RAIS Visio 160 F User manual

1
Arranging ceramic logs - Visio 160 F, LC/RC & 3S
It is very important that you follow this when positioning ceramic “logs” and the
 emberslayerinthereplace.Failuretocarrythisoutcorrectlywillcausethereplace
 tonotburnoptimallyandsoottooccur.
OPSTILLINGSAFSTANDE
ARRANGING CERAMIC ”LOGS” - VISIO 160 F, LC/RC & 3S

2
Important information: Ceramic “logs” and the embers layer
When arranging ceramic “logs” and the embers layer in the combustion chamber, it is important
that they do not cover the pilot ame and its thermocouple, and ember material must not be
placed under the pilot guard.Boththermocouplesmustbekeptfreeoftheemberslayer.
Donotcovertheholesinthemainburner(shownbytheredcircles).
  Pilotame  Second thermocouple for the main burner
OPSTILLINGSAFSTANDE – OVN MED DREJEFOD
IMPORTANT INFORMATION: CERAMIC “LOGS” AND THE EMBERS LAYER
NB!
Please note that there should be a small intermediary space between the “logs” that lie on
theburnersandbetweenthesurroundinglogs,sothereisspacefortheamesinbetween
them.Ifthereisnotspacefortheames,thereplacewillnotburnoptimallyandsootmay
form.
NB!
Themeasurementsonthefollowingphotosaretakenfrom the edge of the base plate.See
photobelow.
cmcm

3
OPSTILLINGSAFSTANDE – OVN MED DREJEFOD
123456
Visio 160 F, LC/RC & 3S
Youwillndtheseceramiclogsinthepackage:
ARRANGING CERAMIC ”LOGS” AND EMBERS
Note the small bump
on the right side
7 8 9 10
NB! Should not
be used for
this model

4
ARRANGING CERAMIC ”LOGS” AND EMBERS
1. Startbysecuringfourburnersinthereplace’sbaseplateasshowninthepicture.
2.  Positionlogno.10betweenthetwomiddleburners(1cmfromthebackwall)asshownin
thepicture.
Procedure:
10
NB! Fornatural gas and city gas please position the
secondary burners as described in the installation manual
onpage28.
ForLPG gas the secondary burners are delivered with two
rowsofholes,andcanbeplacedasbothrightandleftburner.

5
ARRANGING CERAMIC ”LOGS” AND EMBERS
3.  Positionlogno.2(withtherecess)onthemiddlerightburnerasshowninthepicture.
4.  Positionlogno.1(withtherecess)onthemiddleleftburnerasshowninthepicture.
2
1

6
ARRANGING CERAMIC ”LOGS” AND EMBERS
5. Positionlogno.8(withtherecess)onthefarrightburnerasshowninthepicture.
6. Positionlogno.9(withtherecess)onthefarleftburnerasshowninthepicture.
8
9

7
ARRANGING CERAMIC ”LOGS” AND EMBERS
7.  Positionlogno.6asshowninthepicture.
8. Positionlogno.5asshowninthepicture.
6
13 cm13 cm
2 cm2 cm
1 cm1 cm
5
18 cm18 cm 6 cm6 cm
1,5 cm1,5 cm

8
ARRANGING CERAMIC ”LOGS” AND EMBERS
9. Positionlogno.4asshowninthepicture.
10. Positionlogno.3asshowninthepicture.
4
22 cm22 cm
1,5 cm1,5 cm
3
20 cm20 cm
7 cm7 cm

9
ARRANGING CERAMIC ”LOGS” AND EMBERS
5
11. Nowtheglassstonesshouldbespreadoutinthegasreplace.Meassureout1,25lofglass
stonesinameassuringcup.
12. Spreadouttheglassstones(1,25lintotal)oneachsideofthegasreplace-overtheLED
lights.Itisimportantthattheglassstonesarespreadoutinathinlayerthatcoverstheholes
inthebottomofthereplace.

10
ARRANGING CERAMIC ”LOGS” AND EMBERS
13. Nowmeassureout3lofembers(amixofthegreyandblackchips).
14. Spreadtheembers acrossboththeglassstonesandthebaseplatewiththeholes.
Placethelamentsonthepilotarea.
NB! Itisextremelyimportantthat
you do not cover the pilot area and
the holes there(seepage2).