RAMSET XT540 Maintenance and service guide

XT540 TOOL
OPERATOR’S
SAFETY & OPERATING
INSTRUCTION MANUAL
DANGER
THIS TOOL FOR USE BY LICENSED OPERATORS ONLY.
READ AND OBEY ALL SAFETY AND OPERATING
INSTRUCTIONS BEFORE OPERATING TOOL.
SEMI-AUTOMATIC, LOW VELOCITY
PISTON TYPE FASTENING TOOL

Just as no one can merely read a book about driving an automobile and then hope
to drive one safely, no one should attempt to use any Ramset tool without adequate,
competent personal instruction. And just as one must be licensed to drive an automobile,
one must also be licensed to use a powder actuated tool. No automobile instruction
book or instructor can forewarn a learner against all possibilities and emergencies, nor
can Ramset instructors and printed material detail all possible conditions surrounding
the use of Ramset tools and products.
Responsibility for the safe and proper use of this tool rests with the tool user
and the employer.
SAFETY INTRODUCTION DANGER
SAFETY INTRODUCTION DANGER
2
Operator’s and bystanders
must wear eye and hearing
protection.
Never close tool with hand over fastener loading end of the tool.
A serious hand injury from penetration by the piston or a
discharged fastener could result.
Read manual before
operating tool.
DANGER
THIS TOOL IS TO BE USED ONLY BY PROPERLY TRAINED
AND LICENSED OPERATORS.
YOU MUST SUCCESSFULLY COMPLETE THE
RAMSET TRAINING PROGRAM FOR THE
TOOL AND OBTAIN A CERTIFIED OPERATOR’S LICENSE
BEFORE HANDLING, LOADING OR OPERATING THIS TOOL.
ATTEMPTING TO HANDLE OR OPERATE THIS TOOL
WITHOUT PROPER TRAINING AND LICENSING CAN RESULT IN
SERIOUS INJURY TO THE OPERATOR OR BYSTANDERS.
DANGER

Preparation
Acceptable Base Materials
Powder actuated fastening is suitable for
use in the following base materials only:
• PouredConcrete
• StructuralSteel
• MasonryJoints(seepage8)
Never attempt to fasten into any other
type of material. Fastening into other
materials can cause blindness or other
serious injury.
Unacceptable Base Materials
Never attempt to fasten into very hard or
brittle materials such as cast iron, tile,
glass, or rock of any type. These materials
can shatter, causing the fastener and/or base
material fragments to fly free and cause
serious injury to the tool operator and others.
Never fasten into soft base materials, such as
drywall or lumber products. These materials
may allow the fastener to travel completely
through and out the other side, endangering
those in the path of the fastener.
Never fasten into any base material that
does not pass the Center Punch test.
Failure to assure the suitability of the base
material can result in serious injury to the
eyes or other body parts.
Center Punch Test
ALWAYS WEAR SAFETY GOGGLES
WHEN PERFORMING THIS TEST.
1. Always check the material being
fastened into for hardness before
attempting any fastening operation.
2. Using a fastener as a center punch,
strike the fastener against the work
surface using an average hammer
blow and check the results.
Center Punch Test Results
1. If the fastener point is flattened,
the material is too hard for a
powder actuated fastening.
2. If the fastener penetrates the
material easily, the material is
too soft.
3. If the material cracks or shatters,
the material is too brittle.
4. If the fastener makes a small
indentation into the material, the
material is suitable for fastening.
DANGER SAFETY INSTRUCTIONS
SAFETY INSTRUCTIONS
DANGER 3
NEVER FASTEN INTO VERY HARD OR
BRITTLE MATERIALS
NEVER FASTEN INTO SOFT MATERIALS
SUCH AS DRYWALL

Loads & Load Selection Safety
1. Always make a test fastening after
being sure that the base material
is suitable for powder actuated
fastening. Failure to determine the
correct power level to be used may
result in the use of excessive power,
allowing the fastener to pass completely
through the work material, causing
serious or fatal injuries to others who
may be in the path of the fastener.
2. Color-blind operators must always
select loads by number to prevent
use of an incorrect load for the
same reasons as in #1 above.
Workplace Safety
1. Operators and bystanders must
always wear approved eye protection
and approved hearing protection.
Failure to do so may result in blindness
or serious eye injury from flying debris
and loss of hearing from constant or
repeated unprotected exposure to
fastening noise.
2. Always keep the work area clear of
bystanders and unnecessary materials
that could interfere with safe tool
operation. Operating the tool in a
congested or cluttered area may affect
your ability to operate the tool safely.
3. Never operate tool if flammable
or explosive materials are nearby.
Powder loads burn and create sparks
when fired and could ignite these
materials or fumes.
4. Always post warning signs within
50 ft. of the area where fastening
is to be done. Sign must state:
“WARNING - Powder Actuated Tool
In Use”. Failure to warn others may
result in serious injury to them. Contact
Ramset at 1-800-241-5640 to obtain
this sign.
SAFETY INSTRUCTIONS DANGER
SAFETY INSTRUCTIONS DANGER
4
ALWAYS MAKE A TEST FASTENING
COLOR-BLIND OPERATORS MUST
ALWAYS SELECT LOADS BY NUMBER
KEEP WORK AREA CLEAR OF
BYSTANDERS AND CLUTTER
NEVER OPERATE THE TOOL AROUND
FLAMMABLE OR EXPLOSIVE MATERIALS
WARNING
POWDER
ACTUATED
TOOL IN USE
WITHIN 50 FEET
Safety is important – Take proper precautions.
ALWAYS POST WARNING SIGNS

Tool Handling Safety
1. Always be sure tool is operating
properly before attempting to use
it. Follow the “Daily Function Test”
shown to the right and described
on page 9.
2. Always load tool using a strip load
selected directly from a box indicating
the power load type and number.
Never attempt to use loose strip
loads that could be mis-identified.
3. Never carry loose loads in pockets
with pins or other hard objects.
4. Never load a tool unless you intend
to immediately make a fastening.
Loading a tool and leaving it unattended
in the work area can result in the tool
being accidentally discharged by others.
5. Never place your hand or any other
body part over the fastener loading
end of the tool. Serious hand injury
could result from being struck by either
a fastener or the tool piston should the
tool be accidentally fired.
6. Always store the tool unloaded and
keep the tool and the loads securely
locked in a tool box. Keep keys away
f rom children and unlicensed persons.
7. Always keep the tool pointed away
from yourself and others.
8. Never carry a loaded tool around
the work area.
9. Never allow anyone not trained
to use the tool.
10. Never engage in horseplay with
the tool.
11. Using the tool in poorly ventilated
areas, cleaning tool or handling
loads may result in exposure to
lead or other substances known
to cause birth defects, and other
physical harm. Have adequate
ventilation at all times and wash
thoroughly after exposure.
DANGER SAFETY INSTRUCTIONS
SAFETY INSTRUCTIONS
DANGER 5
NEVER LOAD THE TOOL UNLESS IT IS
TO BE USED IMMEDIATELY
NEVER PLACE HANDS OR BODY OVER
MUZZLE OPENING
KEEP TOOL LOCKED & OUT OF THE
REACH OF CHILDREN
ALWAYS DO A DAILY FUNCTION TEST
BEFORE LOADING TOOL
12
Empty

FAILURE TO FOLLOW
INSTRUCTIONS CAN
CAUSE INJURY TO THE
TOOL OPERATOR OR
TO BYSTANDERS.
Fastener Driving Safety
1. Only use the tool for fastening into
a suitable base material.
2. Never fire the tool without a fastener.
Firing a tool without a fastener will
cause the piston to strike the work
surface, and may cause serious injury
to you and others in the work area.
3. Always use the spall guard whenever
possible to minimize flying particles
or debris.
4. Always hold the tool perpendicular
to and firmly against the work
surface when making a fastening.
Failure to do so could allow a fastener
to ricochet.
5. Never attempt to drive a fastener
close to an edge or to another
fastener. See page 8 for guidelines.
ALWAYS FOLLOW THE
MISFIRE PROCEDURE.
If the tool does not fire after the normal
firing sequence, continue to hold the
depressed tool against the work surface
for at least 30 seconds. Then carefully lower
the tool, remove the strip load, and put it
in a can of water or other non-flammable
liquid. Never carelessly discard a strip with
live loads into a trash container.
If the tool becomes stuck or jammed with
a live powder load, keep the tool pointed
in a safe direction, and immediately tag it,
“Danger- defective - do not use”. Lock
the tool in a tool box and call your local
Ramset distributor for assistance.
SAFETY INSTRUCTIONS DANGER
SAFETY INSTRUCTIONS DANGER
6
USE SPALL GUARD WHENEVER POSSIBLE
ALWAYS HOLD THE TOOL
PERPENDICULAR TO THE WORK SURFACE
NEVER DRIVE A FASTENER CLOSE TO
AN EDGE
HOLD THE TOOL FIRMLY AGAINST
THE WORK SURFACE FOR AT
LEAST 30 SECONDS
SPALL
GUARD
90°

FASTENERS / LOADS
FASTENERS / LOADS
7
Your Ramset XT540 Tool uses only the Ramset fasteners and loads shown below or
listed for the tool in the Product Catalog.
Never use any other types of fasteners or strip loads in the Ramset XT540 Tool. Use of other
types of fasteners or loads may cause unintentional load discharge, damage the tool, cause
poor fastening performance, or create a risk of serious injury to the operator or bystanders.
DANGER
LOADS
Ramset RS27 strip loads are specially made for use in the Ramset XT540 Tool.
The power level of the load is indicated by
the number marked on each box, the color
of the box, and the color on the tip of each
load. As the number increases, the power
level also increases.
Always perform the center punch test
described on page 3 to test the base material.
Always make a test fastening using the
lowest power level first. If more power is
required to set the fastener, use the next
higher power level until the powder level
necessary to drive the fastener is reached.
RS27 10 SHOT STRIP LOAD
POWER CATALOG LOAD CASE
LEVEL NUMBER COLOR COLOR
3 3RS27 Green Brass
4 4RS27 Yellow Brass
5 5RS27 Red Brass
.300 HEAD PLASTIC FLUTED DRIVE PINS
.145 Shank Diameter in Shank Lengths from
1/2” to 3”
.300 HEAD PLASTIC
FLUTED DRIVE PINS
WITH 7/8” WASHER
.145 Shank Diameter in Shank Lengths from
1” to 3”
.300 HEAD POWER POINT
PLASTIC FLUTED DRIVE PINS
.150 Straight Shank in Shank Lengths from
1/2” to 3/4”
.150 /.180 Step Shank in Lengths from 1” to
1-7/8”
CEILING CLIP
ASSEMBLIES
Ceiling Clip with 1” or 1-1/4” premounted
.145 Shank Pin and Ceiling Clip with 1” or
1-1/4” Premounted .150/.180 Shank Pin
1/4” - 20 THREADED STUDS
.145 Shank Diameter in Shank Lengths of 1/2”
and 1” and Thread Lengths of 1/2”, 3/4” and 1”
8 mm HEAD TOP-HAT DRIVE PINS
.145 Shank Diameter in Shank Lengths from
1/2” to 1”
CONDUIT CLIP ASSEMBLIES
For 1/2” and 3/4” Diameter Conduit with 1”
Premounted Fastener
TE PINS
.157 Diameter 1/2 to 1-1/2
FASTENERS

FASTENING APPLICATIONS
Your Ramset tool can be used for a wide
range of fastening needs in a variety of base
materials. Reading and follow these important
fastening guidelines will help you get the best
results from your tool, fasteners, and powder
loads, as well as help you perform these
fastening operations safely and effectively.
Powder actuated fastenings are permanent
fastening so attempting to remove a fastener
from concrete or steel may result in serious
injury.
Fastening to Concrete
When fastening into concrete, always maintain
a minimum spacing of 3” between fastenings
and 3” from any free edge. Concrete thickness
should be at least three times the intended
penetration depth into the concrete. The
primary exception to the 3” edge distance
can occur in a sill plate application where,
by necessity, the edge distance is reduced.
Driving fasteners too close to an edge or too
close to each other can cause the concrete
edge to fail or fasteners to fly free.
Fastening to Concrete Block or
to Masonry Walls
While this application is not recommended,
when used, it is necessary to take care to
observe a 3” edge distance to avoid cracking
the block and over penetration of the fastener
to avoid loss of holding value. Fastening
may be made into the horizontal joint but
not into the vertical joint.
Fastening to Steel
Your Ramset tool can be used for fastening
on the flat surfaces of structural steel. When
fastening into steel, always maintain a mini-
mum spacing of 1-1/2” between fastenings
and 1/2” from any edge.
FASTENING APPLICATIONS
FASTENING APPLICATIONS
8
3"
MIN.
3"
MIN.
3" MIN.
3" MIN.
1/2"
MIN.
1-1/2"
MIN.
SPACING WOOD TO CONCRETE
3"
MIN.
3"
MIN.
3" MIN.
3" MIN.
1/2"
MIN.
1-1/2"
MIN.
SPACING — THIN GAUGE
METAL TO CONCRETE
3"
MIN.
3"
MIN.
3" MIN.
3" MIN.
1/2"
MIN.
1-1/2"
MIN.
SPACING — FURRING
STRIP TO CONCRETE
3"
MIN.
3"
MIN.
3" MIN.
3" MIN.
1/2"
MIN.
1-1/2"
MIN.
SPACING — STEEL TO STEEL

TOOL OPERATION
DAILY FUNCTION TEST
Always check the tool first to make sure
that it does not contain a strip load or
fastener. Test the tool several times by
depressing the muzzle bushing fully on a
hard surface and pulling the trigger. You
should hear an audible click as the firing
pin releases. Let up on the tool and check
to be sure that the barrel has opened to the
semi- open position.
OPERATING THE RAMSET XT540
TOOL
Note: Refer to safety precautions before
attempting to operate the tool.
1. Select and insert the fastener.
Select the correct fastener for the
application (see Fastener Selection,
page 7). Point the tool down and away
from yourself and any other person.
1a. Tool fitted with single shot fastener
guide. Insert a fastener, HEAD FIRST
into the fastener guide at the front end of
the tool, making sure the fastener guide
stays in the forward position.
1b. Tool fitted with fastener magazine.
1 - Press the magazine release button.
2 - Slide the magazine cover down.
3 - Insert Ramset collated drive pins.
4 - Push the magazine cover back into
the closed position.
TOOL OPERATING INSTRUCTIONS
TOOL OPERATING INSTRUCTIONS
9
1. SELECT AND INSERT THE FASTENER
1b. TOOL FITTED WITH FASTENER
MAGAZINE
PUSH
12
PERFORM THE FUNCTION TEST WITH
EMPTY, UNLOADED TOOL
Empty

2. Insert the power load.
With the tool in the closed position
insert a power load strip into the
cavity in the base of the rubber handle
and push in until the flat of your finger
tip is firmly against the handle recess.
The first power load is now aligned
with the chamber.
Note: Always use the lowest strength
power load and lowest power setting
first, for a firing test, then adjust the
power to suit the job.
3. Fire the tool.
Press the fastener guide firmly against
the work surface, and pull the trigger.
4. Check the fastener has been
correctly set. (See Fastening
Applications, page 8)
5. Adjust the power, if necessary.
Increase power by increasing
power setting. When maximum
setting is reached, move wheel back
to minimum position and insert next
strength power load.
TOOL OPERATING INSTRUCTIONS
TOOL OPERATING INSTRUCTIONS
10
2. INSERT THE POWER LOAD
5. ADJUST THE POWER, IF NECESSARY

TROUBLESHOOTING
TROUBLESHOOTING
11
Most commonly, problems are caused by over driving due to poor fastener or charge
selection. It is wise to consider these two factors as the first options in trouble shooting.
SYMPTOM POSSIBLE PROBLEMS SERVICE
— Fastener over driven
— Fastener under driven
— Rough action
— Reduction or loss of
power
— Tool misfire
Do not remove the tool
from the work surface
for at least 30 seconds
— Tool Jam
— Cartridge strip does not
index in tool
— Cartridge strip melts
— Cartridge falls out
of the strip
— Too much power
— Fastener too short
— Too little power
— Fastener too long
— Excessive carbon
build up
— Piston not returning to
position
— Faulty piston circlip
— Build up of dirt in tool
— Broken piston
— Failure of tool to
depress completely
— Cartridge strip damaged
— Problem with tool or
faulty charge / power
load
— Damage to power load
chamber
— Cartridge strip damaged
— Strip index mechanism
damaged
— Tool overheated –
fastening rate too high
— “Hot” tool compressed
for too long
— Use a low strength power load or use the
power adjustment feature if applicable
— Select the correct fastener
— Use a higher strength power load or use the
power adjustment feature if applicable
— Select the correct fastener
— Disassemble, clean and lightly oil tool
— Check the length of the piston Return
Spring (Refer to page 13)
— Remove piston. Replace piston circlip
— Clean tool parts
— Replace piston
— Disassemble tool and check all parts for
correct assembly after first removing the
power loads
— Remove and replace with new cartridge strip
— Refer to page 5
— Refer to page 5
— Refer to page 5
— Refer to page 5
— Allow the tool to cool. Disassemble tool to
increase rate of cooling.
— Reduce fastening rate
— Compress tool for a shorter period of time

PARTS SCHEMATIC
PARTS SCHEMATIC
12
XT540

PARTS LIST / MAINTENANCE
PARTS LIST / MAINTENANCE
13
Always make sure the tool is not loaded before performing any service or repair and
always wear safety goggles when cleaning or servicing the tool.
DAILY CLEANING
All front end parts shown in the disassembly section are to be cleaned daily with a good
detergent oil and wire brush. Remove all dirt and carbon buildup and wipe parts dry with
a clean rag. Check all parts for wear or damage before reassembly and replace or repair
any worn or damaged parts.
PERIODIC COMPLETE CLEANING / GENERAL MAINTENANCE
Heavy or constant exposure to dirt and debris may require that the tool be cleaned more
extensively. Complete disassembly and cleaning of all parts may be necessary to restore
the tool to normal operation. General maintenance should be performed every six months
or more often if the tool is subjected to heavy use. General maintenance/complete
cleaning should be done by a qualified repair person.
IMPROPERLY MAINTAINED TOOLS CAN CAUSE SERIOUS INJURIES
TO TOOL OPERATOR AND BYSTANDERS
CLEAN TOOL DAILY
ALWAYS FUNCTION TEST THE TOOL AFTER PERFORMING ANY
SERVICE. SEE PAGE 9 FOR DETAILS ON THE FUNCTION TEST.
MAINTENANCE
XT540 PARTS LIST
KEY PART NO. DESCRIPTION
1 PA37040 FASTENER GUIDE ASSEMBLY
1A 100227 MAGNETIC FASTENER GUIDE ASSM (NOT SHOWN)
2 100167 PISTON RETURN RING (PKG OF 2)
3 010983 PISTON BUFFER/INSULATION RING (PKG OF 2)
4 PA37037 PISTON
5 PA37021 POWER ADJUSTMENT ASSEMBLY
6 PA37007 BARREL ASSEMBLY
7 010975 STOP RING KIT
8 PA37015 COCKING ROD KIT
9 PA37016 CHARGE ADVANCE LEVER ASSEMBLY
10 PA37003 RUBBER GRIP
11 PA37001 OUTER HOUSING ASSEMBLY (L & R)
12 N/A RECEIVER ASSEMBLY
13 PA37009 OUTER HOUSING SCREWS (PKG OF 9)
14 PA37032 HANDLE SCREW (PKG OF 5)
15 PA37017 TRIGGER ASSEMBLY
16 PA37033 END CAP SCREWS (PKG OF 2)
17 PA37004 END CAP
18 PA37030 FIRING PIN SPRING GUIDE
19 PA38160 FIRING PIN ASSEMBLY
20 PA28111 MECHANISM HOUSING ASSEMBLY
21 PA37012 CHARGE ADVANCE SPRING KIT
22 27516A TRIGGER SEAR SPRING KIT
23 PA37023 SPALL GUARD

INSPECTION / TOOL MAINTENANCE
14
INSPECTION / TOOL MAINTENANCE
1. Ensure that no power loads are loaded
in the tool. Remove the power load strip
by pulling it upwards out of the tool.
2. Hold the tool vertical with the fastener
guide/ magazine pointing upwards.
Unscrew the fastener guide/magazine.
If this is too difficult by hand, use pliers.
3. Take out the piston assembly (piston,
piston return spring and buffer).
4. Push the barrel downwards and
unscrew the collar surrounding the
barrel. Remove the barrel assembly.
5. Check the length of the return spring
using the measuring points located on
the top of the tool housing. This check
should be made every 3,000 shots.
6. CHECK:
• The piston tip - replace if it is damaged.
•Thestraightnessofthepiston–ifitis
not straight, replace it.
•Thepistonbuffer-replaceifitisworn
or less than 3/16” thick.
7. Using wire brushes, thoroughly clean all
internal and external steel surfaces of
any carbon buildup.
It is important to clean a Powder Acuated
Tool weekly. The carbon build up from the
explosive material can decrease the effective-
ness of the tool and if not removed, cause long
term damage to the tool.
CAUTION: The tool may become hot during
operation. Tool maintenance should be
performed when the tool has cooled down
to avoid the possibility of receiving burns to
hands.
OK!
CHANGE
STEP 2
STEP 3
STEP 4
STEP 5

INSPECTION / TOOL MAINTENANCE
15
INSPECTION / TOOL MAINTENANCE
Re-assembly is the reverse of
disasssembly
1. Position the barrel’s groove at the top.
2. Insert the barrel’s assembly into the
main housing and screw the knurled
collar by hand. (Do not over tighten).
3. After re-assembly check that the barrel
slides properly in the handle.
4. Slide the buffer onto the piston.
5. Slide the piston return spring onto the
piston.
6. Insert the piston assembly into the barrel.
7. Screw the magazine or the fastener
guide onto the barrel.
8. Without any power loads or fasteners,
test the tool for correct function by
cocking the tool and depressing the
trigger. If this test does not work, do
no attempt to use the tool.

XT540 WARRANTY AND LIMITATIONS
POWDER ACTUATED TOOL
MANUFACTURERS' INSTITUTE INC.
TM
Concrete Fastening Systems
Glendale Heights, IL 60139
800-RAMSET6 (1-800-726-7386)
www.ramset.com
Buy with Confidence...
Buy From Your Authorized Distributor
AN ILLINOIS TOOL WORKS COMPANY
© ILLINOIS TOOL WORKS 2011
PRINTED IN THE U.S.A. Form No. SS165 – 07/11
THE MODEL XT540 TOOL COMPLIES WITH OSHA REQUIREMENTS
AND WITH ANSI A10.3 SPECIFICATIONS
FOR TOOL REPAIR SERVICE CONTACT YOUR LOCAL AUTHORIZED
RAMSET DISTRIBUTOR OR TO FIND YOUR NEAREST RAMSET TOOL
REPAIR CENTER VISIT OUR WEB SITE AT WWW.RAMSET.COM
OR CALL 800-241-5640
Ramset warrants that new XT540 power fastening
tools, parts and accessories will be free from
defects in material and workmanship for the
period shown below.
THREE-YEAR WARRANTY
A three-year warranty will apply to all parts,
except those listed below as normal wearing
parts, or parts which are specifically covered
by an extended warranty.
The following parts are considered normal
wearing parts and are excluded from the
warranty:
• Piston • Buffer • Spring Clips
• Pawls • Piston Rings • Piston Return Spring
The warranty period is based off of tool build
date, determined from the tool serial number.
Ramset may extend the warranty time frame
from the date of purchase with a qualifying
document proving date of purchase.
WARRANTY STATEMENT
Ramset’s sole liability hereunder will be to
replace any part or accessory which proves
to be defective within the specific time period.
Any replacement part or accessory provided
in accordance with this warranty will carry a
warranty for the balance of the period of
warranty applicable to the part it replaces.
This warranty does not apply to part
replacement required due to normal wear.
This warranty is void as to any tool which has
been subjected to misuse, abuse, accidental
or intentional damage, use with fasteners, and
loads not meeting Ramset specification, size,
or quality, improperly maintained, repaired
with other than genuine XT540 replacement
parts, damaged in transit or handling, or
which, in Ramset’s opinion, has been altered
or repaired in a way that affects or detracts from
the performance of the tool.
Ramset MAKES NO WARRANTY, EXPRESSED OR
IMPLIED, RELATING TO MERCHANTABILITY,
FITNESS, OR OTHERWISE, EXCEPT AS STATED
ABOVE and the liability AS STATED ABOVE
AND AS ASSUMED ABOVE is in lieu of all other
warranties arising out of, or in connection with,
the use and performance of the tool, except to
the extent otherwise provided by applicable law.
Ramset SHALL IN NO EVENT BE LIABLE FOR
ANY DIRECT, INDIRECT, OR CONSEQUENTIAL
DAMAGES, INCLUDING, BUT NOT LIMITED TO
DAMAGES WHICH MAY ARISE FROM LOSS
OF ANTICIPATED PROFITS OR PRODUCTION,
SPOILAGE OF MATERIALS, INCREASED COST
OF OPERATION OR OTHERWISE.
Ramset reserves the right to change specifications,
equipment, or designs at any time without notice
and without incurring obligation.
Copyright 2011 Ramset