Raritan ATLANTES FREEDOM VORTEX-VAC AV User manual

Description:
Atlantes Freedom Vortex-Vac toilet: available in 12V or
24V DC, household and elongated size bowl in White
and Almond (bone). Fresh water models utilize onboard
pressurized freshwater and sea water models utilize a
remote pump installed between raw water source and
bowl. SeaFresh model allows switching between fresh
and raw water source.
Three dierent control options are available:
1. Flush Handle Control: provides
momentary operation of ush water and
discharge.
2. Smart Toilet Control: provides timed operation and
independent control of ush water and discharge with
handle or wall switch.
3. Multifunction Momentary Control: provides
momentary operation and independent momentary
control of ush water and discharge.
THE FOLLOWING ARE CAUTIONARY STATEMENTS THAT MUST BE READ AND
FOLLOWED DURING BOTH INSTALLATION AND OPERATION.
WARNING: Raritan Engineering Company, Inc. recommends that a qualied person or electrician install this
product. Equipment damage, injury to personnel or death could result from improper installation.
Raritan Engineering Company, Inc. accepts no responsibility or liability for damage to equipment,
injury or death to personnel that may result from improper installation or operation of this product.
WARNING: HAZARD OF SHOCK OR FIRE
Always use recommended fuse, circuit breaker and wire size.
Motors used with this product are “Ignition Protected”. They are not however, explosion-proof as
dened in 46CFR 110.15-65(e), Subchapter J-Electrical Engineering.
DO NOT run continuously for more than 30 seconds.
Installation and Maintenance Instructions
ATLANTES FREEDOMTM TOILET
VORTEX-VACTM
1
MODEL AV
Pressurized
Freshwater Model
Model and Serial#:
L476 0719jlc
Sea Water Model
(Remote Pump)

2
IMPORTANT SAFETY INSTRUCTIONS:
WARNING:
Young children should NOT be left unsupervised
around toilet. Serious injury or death could occur.
Children can drown in water retained in the bowl.
Seat and/or lid could close and strike child.
Always replace circuit breaker and fuses with
same rating . Use Raritan parts to maintain
ignition protection requirements.
Toilets mounted at or below the waterline must have
a vented loop installed in the discharge line. The top
of the vented loop must be a minimum of 4” (10cm)
above the waterline at the boats greatest angle of
heel (see vented loop manufacturer’s instructions).
Sea Water Models must also have a vented loop
installed between the intake pump and the toilet bowl.
Double clamp all below waterline connections.
Recommended Visual Inspection
For leaks at toilet and hose connections
Hose clamps
Condition of hoses
Seacocks
Condition of wires and connections
In-Line Strainer (if you have one)
• No special toilet paper is required.
• Water should appear in the bowl within ten
seconds. If not, see troubleshooting section.
• Hard objects or stringy substances (paper
towels, feminine hygiene products, filter
cigarettes, etc.) must not be thrown into the
toilet as they will cause damage.
• Always shut o seacock(s) before leaving the
boat unattended.
WARNING: HAZARD OF FLOODING - Always
shut o seacock(s) before leaving the
boat unattended.
Double clamp all below waterline
hose ttings and check frequently for
integrity.
Operation:
Please see instructions included with control to
see how to operate your unit.
L476 0719jlc
Cleaning Instructions
IMPORTANT: Do not use cleaners that contain
ammonia, ethyl acetate, phosphoric acid or
concentrated chlorine bleach. Do not allow acids,
such as vinegar, and other cleaners to sit for
extended periods of time in the toilet. These may
cause damage to the toilet. Do not use abrasive
cleaners or cleaning pads. Flushing fresh water
through toilet when leaving for extended periods
is recommended.
Using C.P. a bio-enzymatic toilet bowl cleaner
(available from Raritan Engineering Part#
1PCP22) will keep the bowl clean and fresh
smelling.
SAFETY/ CLEANING

WINTERIZING
SYSTEM START-UP
1. Open seacock(s).
NOTE: Pressurized freshwater models; open water
source valve.
2. Turn on power to toilet.
3. Flush toilet per Operation Instructions.
4. Check for leaks.
• Improper winter lay up is a major cause of
marine toilet failure.
• Use only nontoxic antifreeze.
• Flush toilet several times to clear waste from
system.
• Dispose of all antifreeze in accordance with
local and federal regulations.
• Winterize holding tanks, plumbing, treatment
systems (MSD’s), etc. independently following
manufacturer’s instructions.
Pressurized Freshwater Models
Parts Required
• 1” (25 mm.) or 1 1/2” (38 mm.) I.D.
discharge hose, approximately 3 feet (1 m.) long
• Two buckets
• Nontoxic antifreeze approximately 1 quart
(1 liter)
Steps
1. Close discharge seacock (if one exists).
2. Shut o intake water at source.
3. Turn o power to unit.
4. Disconnect and drain intake and discharge
hose.
5. Disconnect intake hoses from toilet and place
in one of the buckets.
6. Connect short hose to toilet’s discharge and
place in other bucket.
7. Pour antifreeze in bowl.
8. Turn on power to unit and ush until antifreeze
is removed from the bowl and water is drained
from the solenoid and hose.
9. Disconnect power to toilet.
10. Reconnect intake hoses to water solenoid.
Intake Pump Models
Parts Required
3/4” (19 mm.) I.D. intake hose approximately 3 feet
(1 m.) long.
1” (25 mm.) or 1 1/2” (38 mm.) I.D. discharge hose
approximately 3 feet (1 m.) long.
Two buckets
Nontoxic antifreeze approximately 1 quart (1 liter)
Steps
1. Close the intake and discharge seacocks.
2. Turn o power to unit.
3. Disconnect and drain pump suction hose and
toilet discharge hose .
4. Connect short hoses to pump’s suction intake
and to toilet discharge.
5. Place one empty bucket under hose connected
to toilet’s discharge.
6. Pour nontoxic antifreeze in other bucket.
7. Place hose connected to intake pump into
bucket with antifreeze.
8. Turn on power to unit and ush toilet until
antifreeze begins to be discharged from toilet.
9. Disconnect power from toilet.
RECOMMISSIONING
1. Using the buckets, hoses and approximately
one gallon (3.8 liters) of clean fresh water, ush
antifreeze out of the toilet (see Winterizing).
Dispose of antifreeze in accordance with local
and federal regulations.
2. Reconnect the intake and discharge hoses and
open both seacocks and water source valve.
3. Check all connections for leaks with several
test ushes.
3
IMPORTANT: If toilet does not ush properly
or if water does not enter the bowl within 10
seconds, refer to Troubleshooting.
WINTERIZING
L476 0719jlc

SPECIFICATIONS
4
Plumbing
NOTES: for Wiring
CONVERSIONS
Wire - AWG to mm2
Feet to Meters
Water Consumption:
Water Saver : 2 pint*
Regular Flush: 2 quarts
* requires timing adjustment
Maximum suction of Intake pump
(Maximum height above waterline) 4 Ft. (1.2m) from Intake Pump.
Maximum height of discharge vented loop 10 Ft. (3 m) from base of toilet.
Pressurized water source minimum
requirements
Minimum fLow rate 3 gallons
(11.3 liters )per minutes, Minimum
Pressure 5 PSI(34.5 Kpa)
1. Distances are from source to unit and back to source.
2.
Distance from power source to remote intake pump MUST be included when
determining total distance.Same wire size MUST be used for lower base and
remote intake pump.
3. Recommended conductor wire minimum AWG (mm
2
) for 3% voltage drop.
4. Recommended conductor sizes are based on 105
o
C rated insulation.
Refer to ABYC Standards for other insulation ratings.
5. For 120/240 VAC units use 12VDC specifications from transformer to unit.
AWG 16 14 12 10 8 6 4 2
mm
2
1.5 2.5 4.0 6.0 10.0 16.0 25.0 35.0
Feet 10 15 20 25 30 40 50
Meter 3.1 4.6 6.1 7.6 9.2 12.2 15.2
Hose Sizes
Inlet: 1/2”(12.7 mm.) for freshwater model
3/4” (19 mm.) for sea water model
Discharge: 1”(25.4 mm.) or 1 1/2”(38 mm.)
Units
Voltage
Circuit Breaker/
Fuse size
Toilet Dicharge
amps draw
Remote Pump
Only amp draw 10
feet
15
feet
20
feet
30
feet
40
feet
50
feet
12 VDC 30 18 10 10 AWG 8 AWG 6 AWG 4 AWG 4 AWG 2 AWG
24 VDC 20 10 5 16 AWG 14 AWG 12 AWG 12 AWG 10 AWG 8 AWG
Sea Water Model (sizes based on inlet and discharge added together)
Recommended Wire and Fuse/Circuit Breaker Sizes
Units
Voltage
Circuit Breaker/
Fuse size
Amp draw 10
feet
15
feet
20
feet
30
feet
40
feet
50
feet
12 VDC 25 18 10 AWG 10 AWG 8 AWG 6 AWG 6 AWG 4 AWG
24 VDC 15 10 16 AWG 16 AWG 14 AWG 12 AWG 10 AWG 10 AWG
Pressurized Freshwater Model
Units
Voltage
Circuit Breaker/
Fuse size
Amp Draw 10
feet
15
feet
20
feet
30
feet
40
feet
50
feet
12 VDC 15 10 14 AWG 12 AWG 10 AWG 10 AWG 8 AWG 6 AWG
24 VDC 10 5 16 AWG 16 AWG 16 AWG 16 AWG 14 AWG 12 AWG
Remote Intake Pump Only
L476 0719jlc

5
SPECIFICATIONS
Additional Parts Required
•Two stainless steel mounting bolts or lag screws
(minimum 1/4” [6mm]) and washers)
• 1” (25 mm.) or 1 1/2” (38 mm.) I.D. discharge hose
• 3/4” (19 mm.) for seawater models or 1/2” (13mm)
for freshwater models, reinforced intake hose.
• Hose clamps (two for each connection below
waterline)
• Wire
• Terminals
• Fuse/circuit breaker
Atlantes discharge Maximum recommended 1” or 1 1/2” PVC hose length
Parts included with all models
1. Toilet bowl assembly
2. Mounting hardware
3. Seat
4. One of the following ush controls:
a. Flush handle control
b. Multifunction Momentary Control
c. Smart Toilet Control
5. User guides and Installation guides with labels
Additional Parts included with sea water
model:
1. Remote pump assy.
SIZE Inches
(mm)
Bowl type A B C D E F
Household 19 1/4
( 489)
15
( 381)
17
( 432)
15
( 381)
14 3/8
( 355)
14
( 355)
Elongated 21 1/2
( 545)
18 1/4
( 455)
17
( 432)
15
( 381)
14 1/8
( 359)
14
( 355)
L476 0719jlc

6
MOUNTING
MOUNTING
Mounting surface must be at and solid.
1. Place toilet where it will be located.
Make sure there is room to route hoses.
Make sure seat will open properly.
2. Using a pencil, mark location of bowl
mounting holes (FIG 2).
3. A. If hoses will be routed through oor,
trace one side of toilet on oor.
B. If hoses will be routed through wall,
trace one side of toilet on wall.
4. Remove toilet and mark location for hoses
and wiring on deck or wall.
5. Cut necessary holes for hoses and wiring.
6. Drill holes for toilet mounting bolts/screws.
NOTE: Use 1/4” [6mm] size bolts/screws. To
select proper Screw or Bolt length, measure
thickness of deck plus 1 1/8’’ (29mm).
TIP: Do not install until all wiring and plumbing
is done. Secure toilet to oor after installation is
complete.
CAUTION: Do Not over tighten mounting
bolts. Damage to the toilet bowl may occur.
Tighten both mounting bolts evenly and
slowly.
Mounting Remote Pump
1. Locate remote pump between thru hull t-
ting and toilet bowl.
2. Locate in an area away from berth to keep
noise level down.
3. Use Inline Strainer part# 163000 (optional)
to avoid clogs.
4. Secure remote pump to the oor using four
bolts through the pump base.
1 Install mounting bushings, bolts.
2. Tighten bolts being careful to not over-
tighten (Do not exceed 30 inch lb. when
tightening)
3. Install caps over mounting bolts.
Mounting toilet
L476 0719jlc
FIG 1
FIG 2
FIG 4
A. Vinyl Cap - # VCAP (supplied)
B. ¼-20 S/S Bolt or ¼ S/S Self
Tapping Screw or ¼ S/S Lag Bolt
C. Flat Washer, Stainless Steel
D. Nylon Shoulder Washer -
# F071 (supplied)
E. S/S Lock Washer (used on top
and bottom for nut and bolt)
F. ¼-20 S/S Nut
C.
FIG 3

WIRING\PLUMBING
PLUMBING
WARNING: HAZARD OF FLOODING
Toilets mounted at or below the waterline, at
greatest angle of heel, and connected to a Seacock/
Thru Hull Fitting(s) MUST have VENTED LOOPS
installed in toilet discharge plumbing and between
raw water intake pump and toilet bowl.
Install vented loops per manufacturer’s
instructions. Double clamp all below-waterline
connections.
IMPORTANT
• Fittings and 90° bends should be kept to a
minimum.
• In-Line Strainer may be installed on Sea Water
Models to prevent clogs.
• Discharging untreated sewage is forbidden in all
U. S. waters within the three-mile limit.
• Thru-hull ttings and seacocks must be installed
where they are easily accessible.
• Use only quality reinforced hoses such as Raritan
SANIFLEX (part# SFH).
• Secure all hoses properly.
7
Intake
Seacock
Remote Pump
Electroscan
Discharge
Vented
Loop
Inlet Vented
Loop
Discharge
Seacock
Remote Pump Model mounted
below waterline
Pressurized Freshwater Model
installed below waterline
Electroscan
Waterline
Discharge
Seacock
Waterline
Discharge Vented
Loop
WIRING
FOLLOW THE INSTRUCTIONS INCLUDED
WITH CONTROL
The Atlantes Internal Discharge Hose is equipped
with an Integral Vent. The Integral Vent is for
toilet installations where the discharge ow is
downward and residual water after the ush is
desired. A ush control that adds water at the
end of the ush cycle, such as our Smart Toilet
Control (STC), is required for optimal water
retention.. The toilet must be highest connection
in the discharge plumbing when using this vent
to retain water in the bowl. The maximum height
of water retained is appox. 4” from the bottom
of the bowl. IF THE DISCHARGE PLUMBING
IS ROUTED UPWARD (such as below water
line installations), DO NOT REMOVE THE
VENT CAP (FIG 7b).
Residual Water in the Bowl
To enable Vent, remove Vent Cap. See FIG 8
Toilet Installed above waterline
or above Treatment Device and
or Holding Tank = Downward
discharge ow
Remove vent cap
Toilet installed below waterline
or below Treatment Device
and or Holding Tank = Upward
discharge ow
Do not remove vent cap
A
Vent Cap
L476 0719jlc
FIG 5
FIG 6
FIG 7a
FIG 8
Waterline Waterline
FIG 7b

1. Route wire from control per control
instruction.
2. Install seat. Install discharge hose support strap
between seat nut and the bowl. See FIG 11
3. Install toilet in place, connect hoses and wire
plugs.
CAUTION: To avoid kinking to not pull on
discharge hose, be certain there is no pressure
on the discharge line.
Connecting hoses and wiring to toilet
8
PLUMBING
Intake Lines
Pressurized Freshwater Models
Install a shut o valve in intake line before water
solenoid valve.
1. Connect hose from shut o valve to inlet port
of water solenoid valve at the toilet (FIG 9).
NOTE: To avoid malfunction of water solenoid
due to debris in water, installation of Freshwater
Strainer (190601) is recommended.
Remote Sea Water Models
Intake pump ttings are interchangeable to allow more
exibility during installation. Inlet ports are located
on either side of intake pump. Outlet port (to toilet
bowl) is at top of intake pump.
NOTE: To avoid poor pump performance installation
of strainer (163000) is recommended
1. Slide tting clips to open position.
2. Select inlet port to be used.
3. Install appropriate ttings into inlet and outlet
ports.
NOTE: The 90° tting can be rotated 360°.
4. Install the plug tting into unused inlet port.
IMPORTANT: Be sure not to install plug tting
into outlet port! Damage to pump will occur!
5. Slide tting clips back to closed position.
6. Connect hose from seacock to inlet port of
optional In-Line Strainer if installed.
7. Connect hose from outlet port of In-Line
Strainer to inlet port of intake pump.
8. Connect hose from outlet port of intake pump
to bowl elbow located on back of toilet bowl.
L476 0719jlc
DISCHARGE
PORT
INLET
PORT
FIG 9
FIG 11
From Strainer
Arrow
Open CLIP MUST BE FULLY SEATED
IN CLOSED POSITION
Plug
Inlet Ports
Outlet Port
To Bowl
FIG 10

TROUBLESHOOTING
WARNING: HAZARD OF ELECTRIC SHOCK - Before beginning any work on the toilet, be sure that all
power to the unit has been turned o.
WARNING: HAZARD OF FLOODING - Make sure seacocks are in the CLOSED or OFF position before
working on toilet.
NOTE: The following information reects the most probable causes and solutions to problems although not
every possible cause and solution is provided.
Any questions regarding servicing or operation of the Marine Elegance should be directed to our Technical Support
Department in Millville, NJ or Ft. Lauderdale, FL. Please have model and serial number available before calling.
SOLUTION
1A. Be sure discharge seacock is open. Clear line, remove
clog.
1B. Replumb to eliminate bends and ells.
1C. Clean holding tank vent and vented loop vents
1D. Clean or replace aected parts. Replace hose if needed.
1E. Check voltage at toilet while toilet is running. If
less than nominal voltage of toilet (12 or 24), check
condition of batteries and wire sizes. Check terminals
and wire connections for corrosion (heat at terminals
and junctions indicates a bad or corroded connection).
2A. Raise rear of toilet; check with level.
2B. Be sure seacock is open. Clear line-remove clog.
2C. Check all connections from intake thru-hull to intake
pump to be sure no air leaks are present.
2D. See 1E, above.
2E. Remove or Clear debris from strainer.
3A. Remove and ush bowl with pressure hose to remove
all material. Install strainer in intake line to avoid
recurrence.
3B. Replace hose with Raritan sanitation hose (#SFH).
3C. Flush toilet longer; replace hose if permeated; reroute
hose making a shorter run if possible.
4A. Close intake, then discharge seacock to determine
which is causing problem. If discharge, be sure the
vent or vented loop is clean. If intake, there is too
much pressure on seacock; contact Raritan Technical
Support.
5A. Tighten adapter clamps.
5B. Check seal and motor shaft.
5C. Check and reseat bowl grommet
PROBLEM
1. Poor pumpout, especially
solids.
2. Poor water ow, especially
at front of bowl (or no
water ow).
3. Foul odors from toilet area.
4. Bowl lls while underway.
5. Water leaking from under
unit.
POSSIBLE CAUSE
1A. Clogged discharge line.
1B. Plumbing restrictions, bends and ells.
1C. Clogged vents.
1D. Mineral buildup in hoses and ttings.
1E. Low voltage.
2A. Toilet not level.
2B. Restriction in intake line.
2C. Pump sucking air.
2D. Low voltage.
2E. Clogged strainer.
3A. “Marine life” lodged in rim of bowl.
3B. Permeated discharge hose.
3C. Sewage remaining in discharge line
4A. Pressure buildup at seacocks.
5A. Leaking Bowl Throat adapter.
5B. Leak at shaft seal.
5C. Leak from bowl spud.
TROUBLESHOOTING
9
Tip for Removing Intake Pump
Set screw must be loosened
with 1/8” hex key before
removing the intake pump
from motor
Plug
L476 0719jlc

10
EXPLODED PARTS
ATLANTES FREEDOM VORTEX VAC PARTS LIST
ItemNo. Part No. Description
1 1245SC Seat & Cover Slow Close (White only)
1 1245A Seat & Cover Almond
1 AL030+ Seat & Cover (Elongated)
2 AM002W Atlantes Bowl (White)
2 AM002AW Atlantes Bowl (Bone)
2 AL002W Atlantes Bowl Elongated (White)
2 AL002AW Atlantes Bowl Elongated (Ivory)
3 M23A #10 Lockwasher SS
4 1108A 10-32 SS Nut
5 161123 Macerator Blade
6 31-102 Motor Shaft Seal
7 221110 Discharge Pump Seal Plate
8 221105 O-Ring
9 161115 Impeller
10 221115 Discharge Pump Macerator Housing
11 31-114 Lock Nut 10-32 W/Nylon(3)
12 221012 Discharge Motor 12 V
12 221024 Discharge Motor 24V
13 221125 Bowl Throat Adapter Clamp - Pump
14 AM221120 Bowl Throat Adapter
15 221126 Bowl Throat Adapter Clamp - Bowl
16 F035 Isolation Nut (2)
17 CH57 Rubber slinger
19 AM021 Pump Mounting Bracket
20 221127 Discharge Motor Mounting Clamp
21 221141W Discharge Hose
21A VLVE Vent Valve Assembly
21B FC001 Vent Valve Clamp
22 221135 Joker Valve (2)
23 221145 Discharge Adapter Fitting
24 221146 Joker Valve Insert
25 221160 Discharge Hose Clamp (small)
26 221165 Discharge Hose Clamp (large)
27 F089 Screw: 1/4-20x 2” (2)
28 AM028 Bushing(2)
29 1236AW Spud Assembly
REMOTE INTAKE PUMP
30 166012A Pump Motor 12 volt
30 166024A Pump Motor 24 volt
39 162420 Fitting Clip (3)
40 162000W Remote Intake Pump w/o Motor
41 162410 3/4” Hose Barb Straight
42 162425 O-Ring (3)
43 162415 Plug Fittting
44 162405 3/4” Hose Barb 90oFitting
45 F162VT Inlet Pump Mounting Bolt (4)
46 F144 #10 Washer SS Flat (4)
50 1236E Bowl Elbow
51 AM012 Nipple
52 AM011 Elbow
PRESSURIZED FRESH WATER UNITS
60 221362 Y Fitting
61 221353 Solenoid Valve 12VDC D90
61 221354 Solenoid Valve 24VDC D90
62 221358W Inlet Adapter Assembly 90 Degrees
64 F201 Screw: M4 x 10mm SS Pan Hd
Phillips
65 PLA29 Elbow: 3/4 FPT x 1/2 Barbed
66 SF50W SEA FRESH: CHECK VLV HG
BOWL MOUNTED FLUSH HANDLE
70 AM665W Handle SS W/Set Screw
71 AV600W Flush Control & Wire Harness
72 ETB3 Terminal Block 3 Poles
73 F108 Screw #4 x 7/8” (2)
74 HLWQB 1/4”Split Lock Washer (4)
75 M31 1/4” Brass Flat Washer (8)
76 31-722 Nylon Shoulder Washer (2)
77 F069 1/4” Fiber Washer (2)
78 HSB1 1/4-20 Brass Screw (2)
79 M30 1/4-20 Brass Nut (4)
SMART TOILET CONTROL UNITS
80 STC548W Smart Toilet Control (12 & 24 VDC)
81 STC545 Control Cable 7ft
82 221524 Wall Switch Cover Plate - White
82 221524A Wall Switch Cover Plate - Ivory
83 STC543W Touch Panel W/Back Plate
84 221525 Touch Panel Gasket
MULTIFUNCTION MOMENTARY CONTROL (NOT SHOWN)
221553 Manual (Relay) Control
W183C Cable for multifunction control
SF77 Switch, Vimar
SF74 Bazel , Vimar white
SF71 Frame, Vimar
SOLENOID VALVE PRESSURIZED SEAWATER UNITS
93 CWPS12B 1/2 GC Solenoid valve 12V
93 CWPS24B 1/2 GC Solenoid valve 24V
93 CWPS32B 1/2 GC Solenoid valve 32V
94 CWPSMB Mounting Bracket for CWPS
95 PLA14 1/2” MPT to 3/4” Barbed Nipple (2)
PARTS NOT SHOWN
RTME12D Power Converter for 120/240VAC UNIT
221170 Discharge Hose Strap
221335 Hose, 1/2 inch
221340 Hose Clamps, 1/2 inch
F071 Nylon Shoulder Washer (2)
VCAP+ Vinyl Cap (2)
ADDITIONAL ACCESSORIES AVAILABLE FROM RARITAN
221147 1 1/2” Thru Wall Discharge Kit
221148 1” Thru Wall Discharge Kit
1PCP22 C.P. Cleans Potties, 22 OZ
1PCHGAL Cleans Hoses, Tanks and MSD (gal.)
SFH Sanitation Hose 1 1/2” (sold by foot)
163000 Seawater Inline Strainer
90323 Vented Loop 1 1/2” (38mm) White
90319 Vented Loop 3/4” (19mm) White
90941 Aquavalve White with (3) Straight Tails
+ specify color (W-White, A-Almond)
* specify Voltage (12, 24)
L476 0719jlc

Atlantes Freedom Vortex Vac Exploded Parts View
EXPLODED PARTS
11
L476 0719jlc

L476 0719jlc Specications Subject to Change Without Notice Printed in U.S.A.
530 Orange Street, Millville, NJ 08332 USA
Telephone: [phone] FAX: [phone]
www.raritaneng.com
Fort Lauderdale, FL
Telephone: [phone]
LIMITED WARRANTY
Raritan Engineering Company warrants to the original purchaser that this product is free of defects
in materials or workmanship for a period of one year from the product’s date of purchase. Should
this product prove defective by reason of improper workmanship and/or materials within the war-
ranty period, Raritan shall, at its sole option, repair or replace the product.
1. TO OBTAIN WARRANTY SERVICE, Consumer must deliver the product prepaid, together
with a detailed description of the problem, to Raritan at 530 Orange St., Millville, N.J. 08332. When
requesting warranty service, purchaser must present a sales slip or other document which establishes
proof of purchase. THE RETURN OF THE OWNER REGISTRATION CARD IS NOT A CONDI-
TION PRECEDENT OF WARRANTY COVERAGE. However, please complete and return the
owner Registration Card so that Raritan can contact you should a question of safety arise which could
aect you.
2. THIS WARRANTY DOES NOT COVER defects caused by modications, alterations,
repairs or service of this product by anyone other than Raritan; defects in materials or workmanship
supplied by others in the process of installation of this product; defects caused by installation of this
product other than in accordance with the manufacturer’s recommended installation instructions or
standard industry procedures; physical abuse to, or misuse of, this product. This warranty also does
not cover damages to equipment caused by re, ood, external water, excessive corrosion or Act of
God.
3. ANY EXPRESS WARRANTY NOT PROVIDED HEREIN, AND ANY REMEDY FOR
BREACH OF CONTRACT WHICH BUT FOR THIS PROVISION MIGHT ARISE BY IMPLICA-
TION OR OPERATION OF LAW, IS HEREBY EXCLUDED AND DISCLAIMED. ALL IMPLIED
WARRANTIES SUCH AS THOSE OF MERCHANTABILITY AND OF FITNESS FOR A PAR-
TICULAR PURPOSE, IF APPLICABLE, AS WELL AS ANY IMPLIED WARRANTIES WHICH
MIGHT ARISE BY IMPLICATION OF LAW, ARE EXPRESSLY LIMITED TO A TERM OF ONE
YEAR. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG A LIMITED WAR-
RANTY LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU.
4. UNDER NO CIRCUMSTANCES SHALL RARITAN BE LIABLE TO PURCHASER OR
ANY OTHER PERSONS FOR ANY SPECIAL OR CONSEQUENTIAL DAMAGES, WHETHER
ARISING OUT OF BREACH OF WARRANTY, BREACH OF CONTRACT, OR OTHERWISE.
SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR
CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT
APPLY TO YOU.
5. No other person or entity is authorized to make any express warranty, promise or armation
of fact or to assume any other liability on behalf of Raritan in connection with its products except as
specically set forth in this warranty.
6. This warranty gives you specic legal rights, and you may also have other rights which vary
from state to state.
12