Raritan Marine Elegance 241E User manual

1
Installation and Maintenance Instructions
Description:
Our Marine Elegance Comfort Height Elongated Bowl is
available in 12V or 24V DC. Fresh water model utilizes
onboard freshwater, the Sea water model utilizes a remote
pump installed between raw water source and bowl.
Sea/Fresh model can switch between fresh and raw water
source.
MarineElegance
THE FOLLOWING ARE CAUTIONARY STATEMENTS THAT MUST BE READ AND
FOLLOWED DURING BOTH INSTALLATION AND OPERATION.
WARNING: Raritan Engineering Company, Inc. recommends that a qualied person or electrician install this product.
Equipment damage, injury or death could result from improper installation. Raritan Engineering Company,
Inc. accepts no responsibility or liability for damage to equipment, injury or death that may result from improper
installation or operation of this product.
WARNING: HAZARD OF SHOCK OR FIRE
Always use recommended fuse, circuit breaker and wire size.
 Motorsusedwiththisproductare“IgnitionProtected”.Theyarenothowever,explosion-proofasdenedin46CFR
110.15-65(e),SubchapterJ-ElectricalEngineering.
DO NOT Install in the area requiring ignition protected devices.
DO NOT run continuously for more than 30 seconds.
Model and Serial Number:
1-800-352-5630
www.raritaneng. com
L442 1221jlc
Comfort Height
Link to online
Warranty
Registration
Model 241E with Smart Handle
Operation of handle:
Pull Handle Forward:
Pull handle forward and release: starts a timed ush,
intake pump starts followed by discharge pump.
Push Handle Backward:
Push and hold: runs just the discharge pump for a “dry
bowl”ush.
IMPORTANT: Discharge and Inlet Pump / Valve MUST
BE wired for proper operationand programming.
Smart Toilet Control: provides timed operation and
independant control of water and discharge.

2
SAFETY
IMPORTANT SAFETY INSTRUCTIONS:
WARNING:
Young children should NOT be left unsupervised
around toilet. Serious injury or death could
occur. Children can drown in water retained in
the bowl. Seat and/or lid could close and strike
child. Always replace circuit breaker and fuses
withsamerating.UseRaritanpartstomaintain
ignition protection requirements.
Toilets mounted at or below the waterline must have
a vented loop installed in the discharge line. The top
oftheventedloopmustbeaminimumof4”(10cm)
above the waterline at the boats greatest angle of
heel(seeventedloopmanufacturer’sinstructions).
Sea Water Models must also have a vented loop
installed between the intake pump and the toilet bowl.
Double clamp all below waterline connections.
Recommended Visual Inspection
For leaks at toilet and hose connections
Hose clamps
Condition of hoses
Seacocks
Condition of wires and connections
In-LineStrainer(ifyouhaveone)
• Nospecialtoiletpaperisrequired.
• Water should appear in the bowl within ten
seconds. If not, see troubleshooting section.
• Hard objects or stringy substances (paper
towels, feminine hygiene products, filter
cigarettes, etc.) must not be thrown into the
toilet as they will cause damage.
• Alwaysshutoseacock(s)beforeleavingthe
boat unattended.
WARNING: HAZARD OF FLOODING - Always
shutoseacock(s)beforeleavingthe
boat unattended.
Double clamp all below waterline
hosettingsandcheckfrequentlyfor
integrity.
Cleaning Instructions
IMPORTANT: Do not use cleaners that contain
ammonia, ethyl acetate, phosphoric acid or
concentrated chlorine bleach. Do not allow acids,
such as vinegar, and other cleaners to sit for
extended periods of time in the toilet. These may
cause damage to the toilet. Do not use abrasive
cleaners or cleaning pads. Flushing fresh water
through toilet when leaving for extended periods
is recommended.
Using C.P. a bio-enzymatic toilet bowl cleaner
(available from Raritan Engineering Part#
1PCP32) will keep the bowl clean and fresh
smelling.
L442 1221jlc

3
WINTERIZING
Winterizing:
• Improperwinterlayupisamajorcauseofmarine
toilet failure.
• Useonlynontoxicantifreeze.
• Flush toilet several times to clear waste from
system.
• Disposeofallantifreezeinaccordancewithlocal
and federal regulations.
• Winterize holding tanks, plumbing, treatment
systems(MSD’s),etc.independentlyfollowing
manufacturer’sinstructions.  
Pressurized Freshwater Models
Parts Required
• 1”(25mm.)or11/2”(38mm.)I.D.
dischargehose,approximately3feet(1m.)long
• Twobuckets
• Nontoxicantifreezeapproximately1quart
 (1liter)
Steps
1. Closedischargeseacock(ifoneexists).
2. Shutointakewateratsource.
3. Turnopowertounit.
4. Disconnect and drain discharge hose.
5. Disconnect intake hoses from water solenoid
and place in one of the buckets.
6. Connect short hose to toilet’s discharge and
place in other bucket.
7. Pour antifreeze in bowl.
8. Turnonpowertounitandushuntilantifreeze
is removed from the bowl and water is drained
from the solenoid and hose.
9. Disconnect power to toilet.
10. Reconnectintakehosestowatersolenoid.
Remote Intake Pump Models
Parts Required
3/4”(19mm.)I.D.intakehoseapproximately3feet
(1m.)long.
1”(25mm.)or11/2”(38mm.)I.D.dischargehose
approximately3feet(1m.)long.
Two buckets
Nontoxicantifreezeapproximately1quart(1liter)
Steps
1. Close the intake and discharge seacocks.
2. Turnopowertounit.
3. Disconnect and drain intake hose and discharge
hose .
4. Connect short  hoses to toilet’s intake and
discharge.
5. Place one bucket under hose connected to
toilet’sdischarge.
6. Pournontoxicantifreezeinotherbucket.
7. Place hose connected to intake pump into
bucket with antifreeze.
8. Turn on power to unit and ush toilet until
antifreeze begins to be discharged from toilet.
9. Disconnect power from toilet.
RECOMMISSIONING
1. Using the buckets, hoses and approximately
onegallon(3.8liters)ofcleanfreshwater,ush
antifreezeoutofthetoilet(seeWinterizing).
Dispose of antifreeze in accordance with local
and federal regulations.
2. Reconnecttheintakeanddischargehosesand
open both seacocks and water source valve.
3. Check all connections for leaks with several
testushes.
SYSTEM START-UP
1. Openseacock(s).
NOTE: Pressurized freshwater models; open water
source valve.
2. Turn on power to toilet.
3. Flush toilet per Operation Instructions.
4. Check for leaks.
IMPORTANT: If toilet does not ush properly
or if water does not enter the bowl within 10
seconds, refer to Troubleshooting.
Operation: Please see instructions included
with control to see how to operate your unit.
L442 1221jlc

4
Pressurized Freshwater Model - Recommended Wire and Fuse/Circuit Breaker Size
Sea Water Model - Recommended Wire and Fuse/Circuit Breaker Size
Plumbing
NOTES: for Wiring
Hose Sizes
INLET
1/2”(12.7mm.)forfreshwatermodel
 3/4”(19mm.)forseawatermodel
Discharge
1”(25.4mm.)or11/2”(38mm.)
CONVERSIONS
Wire - AWG to mm2
Feet to Meters
AWG 16 14 12 10 8 6 4 2
mm
2
1.5 2.5 4.0 6.0 10.0 16.0 25.0 35.0
Feet 10 15 20 25 30 40 50
Meter 3.1 4.6 6.1 7.6 9.2 12.2 15.2
1. Distances are from source to unit and back to source.
2.
Distance from power source to remote intake pump MUST be included when
determining total distance.Same wire size MUST be used for lower base and
remote intake pump.
3. Recommended conductor wire minimum AWG (mm2) for 3% voltage drop.
4. Recommended conductor sizes are based on 105oC rated insulation.
Refer to ABYC Standards for other insulation ratings.
5. For 120/240 VAC units use 12VDC specifications from transformer to unit.
Maximum suction of Intake Pump
(Maximum height above waterline)
4  (1.2m) from Intake Pump
Maximum height of discharge vented
loop
10  (3 m) from base of toilet
Pressurized water source minimum
requirements
Minimum ow rate 5 gallons
(19 liters) per minute. Minimum
pressure 5 PSI (34.5 KPA)
Units
Voltage
Circuit
Breaker/
fuse size
(amps)
Toilet
Discharge
Amps draw
Remote
Pump Only
Amp draw
10 feet 15 feet 20 feet 30 feet 40 feet 50 feet
12 VDC 30 18 10 10 AWG 8AWG 6AWG 4 AWG 4 AWG 2 AWG
24 VDC 20 10 5 16AWG 14 AWG 12 AWG 10 AWG 10 AWG 8AWG
Units
Voltage
Circuit
Breaker/fuse
size(amps)
Amp draw 10 feet 15 feet 20 feet 30 feet 40 feet 50 feet
12 VDC 25 18 10 AWG 10 AWG 8AWG 6AWG 6AWG 4 AWG
24 VDC 15 10 16AWG 16AWG 14 AWG 12 AWG 10 AWG 10 AWG
L442 1221jlc
101
4 [260]
141
2 [368]
INCH
[MM]
161
2 [419] 181
2 [470]
161
2 [420]
215
8 [549]
Atlantes discharge Maximum recommended 1” or 1 1/2” PVC hose length
SPECIFICATIONS
4
Discharge maximum recommended 1” or 1 1/2” PVC hose length

5
• 1”(25mm.)or11/2”(38mm.)I.D.dischargehose
• 3/4”(19mm.)I.D.reinforcedintakehose
• 3/4”(19mm.)and1”(25mm.)or11/2”(38mm.)hose
clamps(twoforeachconnectionbelowwaterline)
• Wire
• Terminals
• Fuse/circuitbreaker
Parts included with all models:
1. Toilet bowl assembly
2. Mounting bracket kit
3. Seat
4. Flush control - includes User and Installation guides.
(Insomecasesdistributionpointsmaypackageand
sellcontrolsseparately.)
5. User guide and Installation guide with labels
Additional Parts included with sea water model:
1. Remotepumpassy.
2. Relayforremotepump(SeaFreshmodelsonly)
Additional Parts Required:
MOUNTING
Mounting Toilet
Mounting surface must be at and solid.
Seat must open more than 90 degrees.
Discharge Hose Support Strap
Important: Discharge Hose should be supported. Attach
support strap to seat bolt as shown in FIG 1.
For pressurized fresh water and remote intake pump
models, using through deck plumbing
Mounting toilet to deck
1. Mark deck and walls where center of bowl will be,
FIG 2
FIG 1
Installing the seat and discharge hose
support strapping
FIG 2
WALL
MARK HERE
L442 1221jlc

6
L442 1221jlc
83
4[222]
BOWL CENTER LINE.
ALIGN AT WALL.
CHECK
MEASUREMENT FOR
PROPER SCALE
7/32 [5.5]
NOMINAL
DRILL SIZE
HOLES FOR BOWL
MOUNTING BRACKETS
DISCHARGE HOSE
See #5 under Mounting
See #5 under
Mounting
WIRES See #5 under
Mounting
INLET HOSE
IMPORTANT:
Holes for Wires and
Hoses are for F and R
Models through deck.
INCH [MM]
L500
Mounting Template
Model 2411
WALL MARK HERE
HOLES FOR BOWL
MOUNTING BRACKETS
7/32 [5.5]
NOMINAL
DRILL SIZE
HOLES FOR BOWL
MOUNTING BRACKETS
BRACKET ALIGNMENT
LINES
FIG 3
FIG 4
FIG 5
FIG 6
2. Place Mounting Template on deck, against the
wall with arrow located on center mark and
 securewithtape(FIG3)
3. Drillholesforoormountingbracketsat
 location (FIG4)
4. Lineupoutsideedgesofoormounting 
brackets with adjacent lines on mounting
template. Securebrackets to deck using mount-
 ingscrewsandatwasher(FIG5)
7. Mount toilet to mounting bracket as shown in
 FIG6
5. Drillholesfordischargehose(2”(51mm.)for
11/2”hose;11/2”(38mm)for1”hose),inlet
hose(7/8”(22mm.)andwires(3/4”(19mm.)
Note: check outside diameter of the hoses and
adjust hole sizes accordingly.
6. Complete  plumbing and wiring before
installing toilet.
MOUNTING

7
PLUMBING
PLUMBING
WARNING: HAZARD OF FLOODING
Toilets mounted at or below the waterline, at greatest
angle of heel, and connected to a Seacock/Thru Hull
Fitting(s) MUST have VENTED LOOPS installed in
toilet discharge plumbing and between raw water
intake pump and toilet bowl.
Install vented loops per manufacturer’s instructions.
Sea Water Models installed below the waterline
MUST have a vented loop installed between the intake
pump and the toilet bowl.
Double clamp all below-waterline connections.
IMPORTANT
• Fittings and 90° bends should be kept to a
minimum.
• In-Line Strainer may be installed on Sea Water
Models per Installation Instructions. This will
prevent clogs.
• Discharging untreated sewage is forbidden in all
U. S. waters within the three-mile limit.
• Thru-hull ttings and seacocks must be installed
where they are easily accessible.
• Use only quality reinforced hoses such as Raritan
Saniex (SFH)
• Secure all hoses properly.
Waterline
Pressurized Freshwater Model Installed
Above/below Waterline
Discharge
Pressurized Fresh-
water
Source
Shut o Valve
Waterline
remote pump
Electroscan
Waterline
Discharge Seacock
Waterline
Discharge Vented
Loop
Intake Vented Loop
Discharge
Seacock Intake Seacock
Electroscan
Pressurized Freshwater Model Installed
below Waterline
Holding Tank
Residual Water in the Bowl
The Marine Elegance is equipped with an integral
vent to maintain water in the bowl when the plumb-
inglinesarerouteddownward(SeeFIG8aandFIG
8b).TheSmartToiletControl(STC)isdesignedto
addwaterattheendoftheushcycle.Thetoilet
will not hold more than about 4” in the bowl. If any
of the discharge hose runs higher than the internal
integralvent,DONOTREMOVETHEVENTCAP.
For vent to work properly in downward installa-
tion,theventcapmustberemoved(seeFIG9).
Remote Intake Pump Model Mounted
below Waterline
Toilet Installed above waterline
or above Treatment Device and
or Holding Tank = Downward
dischargeow
Remove vent cap
Toilet installed below waterline
or below Treatment Device
and or holding Tank = Upward
dischargeow
Do not remove vent cap
FIG 7a
FIG 8a
FIG 9
Vent Cap
FIG 7b
FIG 7c
FIG 8b
ToenableIntegralVent,removeVentCap(FIG9),
connect¼hoseandconnecthosetoadeckventtting
(ReferenceFIG7C).Hoseanddeckttingnot
included.
L442 1221jlc

8
Connecting Remote Pump
Intake pump ttings are interchangeable to allow more
exibilityduringinstallation.Inletportsarelocatedoneither
sideofintakepump.Outletport(totoiletbowl)isattopof
intakepump(FIG12).
NOTE: To avoid poor pump performance installation
ofstrainer(163000)isrecommended
1.Slidettingclipstoopenposition(FIG11).
2. Select inlet port to be used.
3.Installappropriatettingsintoinletandoutletports.
NOTE:The90°ttingcanberotated360°.
4.Installtheplugttingintounusedinletport.
Discharge
port
Inlet
port
Discharge Lines
Raritan Sanitation Hose is recommended. Use part
number SFH for 1 ½” hose or SFH1 for 1” hose
1.Connectsanitationhosetodischargettingontoilet.
NOTE: Dischargettingisdesignedfor1”or1½”
hose.1½”hoseissecuredattopofttingand1”is
secured at the bottom. It is not necessary to remove
the1”barbifusing1½”hose.Usethettingasis.
2.Runhosetoappropriatedevice(e.g.:treatment
system,holdingtank,etc.).
NOTE: If installation requires routing through the
backwallratherthantheoor,90degreekitsare
available:
Usepart#221147for1½”hoseor221148for1”hose.
Intake Lines
Pressurized Freshwater Models
1.Connect½(13mm)I.D.hosetopressurized 
freshwater supply.
2.Installashutovalveinintakelinebeforewater
solenoid valve.
3.Connecthosefromshutovalvetoinletportof
water solenoid valve at the toilet.
NOTE: To avoid malfunction of water solenoid due to
debris in water, installation of Freshwater Strainer
(190601)isrecommended.
FIG 10
FIG 11
FIG 13
Open
Arrow
Plug
Inlet Ports
Outlet Port
To Bowl
FIG 8
5. Slidettingclipsbacktoclosedposition(FIG11)
6. Connecthosefromseacocktoinletportofintake
pump. If used, strainer is in-line. Use hose clamp
provided.
IMPORTANT: Double clamp all below waterline
hose connections!
7. Connect hose from outlet port of intake pump to
bowl elbow located on back of toilet bowl.
Mounting Remote Pump
1. Remotepumpuses¾”(19mm)IDhoseforconnec-
tion.
2.Locateremotepumpbetweenthruhullttingand
toilet bowl.
3. Locate in an area away from berth to keep noise
level down.
4.UseInlineStrainer(optional)toavoidclogs.
5.Secureremotepumptotheoorusingfourbolts
throughthepumpbase(FIG13).
Closed
IMPORTANT: Be sure not to install plug tting into
outlet port! Damage to pump will occur!
PLUMBING
L442 1221jlc
FIG 12

9
WIRING
WIRING
WARNING: Hazard of Shock and Fire
• Always use proper wire, wire connectors and fuse/
circuit breaker. See Specication Chart.
• Secure wire properly.
• Do not connect appliances to toilet circuit.
• Make sure power is o before proceeding.
• Use proper wire terminals for all wire connections.
Mounting controls:
Refer to instruction enclosed with control.
Install the Warning Label (L322) where it can be easily
seen.
5. Routewirefromcontrolperwiringdiagrams.
Caution: To avoid kinking, do not pull on the
discharge hose. Be certain there is no pressure on
the discharge line.
Connect Hoses and wiring to toilet
Tip for Removing Intake Pump
Plug
Set screw must be loosened
with 1/8” hex key before
removing the intake pump
from motor
L442 1221jlc
2. Select proper wire and fuse/circuit breaker size
fromSpecicationsonInstallationpage.
3. Install fuse/circuit breaker in positive line at
source.
4. Wire control to the toilet and battery using one
of the wiring diagram supplied with the Smart
Toilet Control.
1. Determine proper wire size by measuring distance
from:
• PowerSourcetotoiletandbacktopowersource.
• Remotepumpunits-alsoincludedistancefrompower
source for remote pump and back to power source.
Same wire gauge must be used for both lower base and
remote pump.
PRESSURIZED FRESHWATER
VALVE
BLACK
BLUE
REMOTE INTAKE
PUMP
BLACK
(14AWG)
ORANGE/RED
(14AWG)
ORANGE
INTAKE
DISCHARGE
BATT + BATT -
STC(H) SMART TOILET CONTROL
STC RARITAN
DISCH + RED
WHITE
DISCH - BLACK
SENSALEVEL
INLET+ BLUE INLET - BLACK
COMMON
FLOAT FROM MSD
TO MSD
FUSE/
CIRCUIT BREAKER
BATTERY
SEE
RECOMMENDED
WIRE SIZE
ORANGE
BLUE
WHITE
WHITE
BLUE
BLUE
RED
RED
DISCHARGE PUMP
RED
RED BLACK
BLACK
BLACK
INLET = NORMALLY OPEN
DISCHARGE = NORMALLY OPEN
WALL
SWITCH
PANEL

10
Marine Elegance Comfort Height PARTS LIST - Smart Handle
EXPLODED PARTS
Item# Part No. Description
1 241011SC Seat & Cover (Slow Close)
2 241101 ME Bowl, Hgt, White
3 M23A #10 Lockwasher SS (5)
4 1108A 10-32 SS Nut
5 161123 Macerator Blade
6 31-102 Motor Shaft Seal
7 221110 Discharge Pump Seal Plate
8 221105 O-Ring
9 161115 Impeller
10 221115 Discharge Pump Macerator Housing
11 31-114 Lock Nut 10-32 W/Nylon(3)
12 221012 Discharge Motor 12 V
12 221024 Discharge Motor 24V
13 221125 Bowl Throat Adapter Clamp - Pump
14 221120 Bowl Throat Adapter
15 221130 Bowl Throat Adapter Clamp - Bowl
16 221158 Discharge Pump Support Bracket
for part 241101
17 F193VT Screw 10-32 X 3/8 W/VT
21 221141W Discharge Hose
22 221135W Joker Valve (2) (Also includes #24)
23 221145 Discharge Adapter Fitting
24 221146 Joker Valve Insert
25 221160 Discharge Hose Clamp (small)
26 221165 Discharge Hose Clamp (large)
27 VLVE Vent Valve Assembly
28 FC001 Vent Valve Hose Clamp
29 221150 Spud Seal
31 221210 ME Bowl Mtg Bushing (2)
32 F200 Screw Mtg, 18-8 SS Hex
Slotted #8 x 2” (2)
33 221215 ME Bowl Mounting Cap (2)
34 241130M ME Mounting “L” Brackets (2)
35 F189 ME Screw: Bowl Mounting (2)
36 F321 ME Washer Fender Style (2)
REMOTE INTAKE PUMP UNITS
40 166012A Pump Motor 12VDC
40 166024A Pump Motor 24VDC
41 162000W Remote Intake Pump w/o Motor
42 162405 3/4” Hose Barb 90° Fitting
43 162410 3/4” Hose Barb Straight
44 162415 Plug Fitting
45 162420 Fitting Retaining Clip (3)
46 162425 O-ring (3)
47 F162VT Inlet Pump Mounting Bolt (4)
48 F144 #10 Washer SS Flat (4)
50 PLA26 Elbow Adapter 3/4 X 1/2
PARTS NOT SHOWN
221175 L Bolt (2)
221170A Discharge Hose Support Strap
F188 Well Nut 10-32 (3)
F144 Washer #10L 18-8 SS (2)
MOUNTING BRACKET ASSEMBLY
221230W Mounting Bracket w/Hardware
(includes items 31-36)
FLUSH CONTROL OPTIONS
SMART TOILET CONTROL
80 STC548W Smart Toilet Control (12 & 24 VDC)
81 STC545 Control Cable 7 ft
83 STC543 Touch Panel w/Back Plate
HANDLE ASSEMBLY
70 AM665W Handle replacement with set screw
71 AV600W Handle Flush Control Replacement
72 AM667 Microswitch V7 Series, 25A at 250 VAC
73 AM666 Spring .250 X 1.375, 316 S/S
74 ETB3 Terminal Block, 3 Poles, Push Connection
75 F108 Screw: #4 X 7/8 Phil. Flat Head, Type B
Self Threading, 18-8 S/S (2)
REPAIR KITS
MERK Discharge Pump Repair Kit (includes #6, 8, 22 and 24)
22100** Discharge Pump Assembly (includes #3 thru 12 and 21
thru 28)
ADDITIONAL ACCESSORIES AVAILABLE FROM RARITAN
NOT INCLUDED
91 221147 1 1/2 inch Thru Wall Discharge Kit
92 221148 1 inch Thru Wall Discharge Kit
1PCP32 C.P. Cleans Potties, 32 OZ
1PCHGAL Cleans Hoses, Tanks and MSD (gal)
SFH Sanitation Hose 1 1/2” (sold by foot)
SFH1 Sanitation Hose 1” (sold by foot)
163000 Seawater Inline Strainer
RTME12D Power Converter for 120/240 VAC
KO2 Deodorant System (Seawater Models)
1PKO32 Kills Odors, 32oz
STCTSA Holding Tank Full Sensor (Sensa Level TM)
For use with STC Flush Control.
STCFL Holding Tank Full Sensor (Float Switch)
For use with STC Flush Control.
** Specify Voltage
L442 1221jlc
PRESSURIZED FRESH WATER UNITS
60 221351 Solenoid Valve 12VDC
60 221352 Solenoid Valve 24VDC
61 221356 ME Nut 3/4 BSP
62 221357 ME Hose Adapter, Straight
67 221335 Hose 1/2”
68 221340 Hose Clamps 1/2” (2)
69 221300 Vacuum Breaker Assembly