Raritan Crown Head Manual

1
THE FOLLOWING ARE CAUTIONARY STATEMENTS THAT MUST BE READ AND
FOLLOWED DURING BOTH INSTALLATION AND OPERATION.
WARNING: Raritan Engineering Company, Inc. recommends that a qualied person or electrician install this
product. Equipment damage, injury to personnel or death could result from improper instal-
lation. Raritan Engineering Company, Inc. accepts no responsibility or liability for damage to
equipment, injury or death to personnel that may result from improper installation operation of
this product.
WARNING: HAZARD OF SHOCK OR FIRE
Always use recommended fuse, circuit breaker and wire size.
Motors and relays used with this product are “Ignition Protected”. They are not however, ex-
 plosion-proofasdenedin46CFR110.15-65(e),SubchapterJ-ElectricalEngineering.
DO NOTrunthissystemdry(withoutwater).
DO NOTruncontinuouslyformorethan30seconds.
WARNING: HAZARD OF FLOODING -Alwaysshutoseacock(s)beforeleavingtheboatunattended.
 Wheneverpossiblehoseconnectionsshouldbesecuredusingtwo(2)all-stainlesssteelhose
 clamps.Integrityofclamps,hosesandttingsshouldbecheckedperiodically.
INTRODUCTION
The Crown Head is a powerful centrifugal
macerating toilet that thoroughly breaks down
waste in preparation for treatment or holding and
requires little maintenance. It can be ordered with
a90degreeorastraightdischargetting,awhite
marine-size bowl or household-style bowl available
in either white or almond.
OPERATION
CAUTION: The Crown Head motor is designed
to be used as a toilet and is not rated for
continuous duty.
TheCrownHeaddoesn’trequirespecialtoiletpaper,
however,hardobjectsorstringysubstances(paper
towels,femininehygieneproducts,ltercigarettes,
etc.)must not be thrown into the toilet as they will
cause damage.
A. Momentary Operation Using Push-button
Switch (#164000BR) - not included: Depress
button and hold. Water should appear in the
bowl within one to four seconds.  Flush as
necessary.
MAINTENANCE
1. Rell the reservoir when empty; occasionally
check that it has not run dry.
 C.P.,CleansPotties,(1PCP22)helpsminimize
the need for cleaning.
Use only Raritan Cleans Potties as an additive in
the Concentrate tank. Other products may cause
damage to the internal parts of the toilet.
2. Using C.P. a bio-enzymatic toilet bowl cleaner
(available from Raritan Engineering) will keep
the bowl clean and fresh smelling.
Do not use any chemical that contains ammonia,
ethyl acetate, phosphoric acid or concentrated
chlorine bleach as a cleaner. These may cause
damage to the toilet.
3. Make a periodic visual check for leaks at the base of
the toilet and at hose connections.
4. Checksemiannuallytoensureallwireterminalsand
junctions are corrosion-free.
5. Whenboatisnotinuse,ushingthesystemwithfresh
water will help minimize odors and reduce mineral
buildup.
1/2” (1.3cm)
(approx.)
2”
(5.1cm)
13 7/8” (34.2cm)
10 7/8” (27.6cm)
11 7/8” (30.2cm)
14 3/8”(36.5)Household-style
13”(33cm)
Marine-size
17 3/8”
(44.1cm)
Household-style
17”
(43.2cm)
Marine-size
FIG 1
Side
Front
6 1/4”
(15.9cm)
8 9/16”
(21.9cm)
20”(50.8cm) Household-style
17”(43.2cm)
Marine-size
L910116jlc
1
CROWN HEAD - Overall Dimensions
crown head™
CENTRIFUGAL DISCHARGE SERIES AUTOMATIC MARINE TOILET
INSTALLATION, OPERATION AND MAINTENANCE INSTRUCTIONS

2
WINTERIZING
WARNING: If connected to a Lectra/San or Purasan
treatment system there should not be any antifreeze in
the system when activating the Lectra/San orPurasan.
Injury to personnel or damage to property could
result if the Lectra/San or Purasan is activated with
antifreeze in the system.
Improper winter lay up is a major cause of marine
toilet failures.
1.Closetheintakeanddischargeseacock.Disconnect
and drain the intake and discharge hoses. Winterize
seacocks and hoses.
2. Youwillneedtwobuckets,threefeetof3/4”(19mm)
hose,threefeetof11/2”(38mm)hoseandaquart
(.95liter)ofnon-toxicantifreeze.
NOTE: Use only non-toxic antifreeze in this unit.
3. Pouraboutonequart(.95liter)ofnon-toxicantifreeze
into one of the buckets. Place intake hose in this
bucket. Place empty bucket under discharge hose.
To ensure antifreeze has circulation through the entire
toilet,ushuntilantifreezeisdischarged.
4.Antifreeze should remain in the toilet until
recommissioning. This will protect both intake and
discharge sides of the pump. Pouring antifreeze into
the bowl will only protect the discharge side of the
pump, allowing the intake side to possibly freeze.
NOTE: Holding tanks, seacocks and treatment
systems need to be independently winterized,
stored and recommissioned (see manufacturer’s
instructions).
RECOMMISSIONING
1. Usingthebuckets,hosesandagallonofcleanwater,
ush the antifreeze out of the toilet.  Dispose of
antifreeze properly, in accordance with local and
federal regulations.
2.Reconnectthehosesandopenbothseacocks.
3. Check all connections for leaks with several test
ushes.
SYSTEM COMPONENTS
Before starting installation please be sure that all parts
that were ordered with your model have been included:
ThecompleteCrownHeadunitincludes:bowl,seatand
cover, motor assembly, shroud assembly, siphon and check
valveassembly,Concentratetank,2oz.(59ml)ofC.P.,
twomountingstripsandanowner’smanual.
CrownHeadunitspurchasedforusewith120/240volt
ACpowerwillalsoincludearectiedtransformerunit
(#RTCH24DA),withinstructions.
INSTALLATION
ReadThis EntireSection Before Beginning Installation.
Below water line installations must include vented
loops. The top of the loop must be above the waterline
at maximum heel to prevent siphoning. (See FIG 3.)
Additional parts required:  Stainless steel fasteners,
a single pole push button switch (#164000BR) and a
continuousdutysolenoid(#CDS*)relayorRaritimetimer
(#RTC*), 1 1/2” (38 mm) I.D. discharge hose (#SFH)
and a reinforced 3/4” (19mm) I.D. intake hose, hose
clamps,wire,fuseorcircuit breaker(seeCrownHead
Specicationchart).
Mounting the Crown Head:BesureCrownHeadison
solid deck construction in a dry location. Never mount
the Crown Head where it may be subject to shower
spray or other sources of external water. Place the
supplied rubber mounting strips between the base plate
oftheCrownHeadandthedeck,allowingairtocirculate
under the motor to prevent moisture from accumulating.
Usestainlesssteelfastenerswithaminimumsizeof1/4”
(6mm).
1. Intake Lines:A3/4”(19mm)thru-hullttingand
seacock located in an accessible area is required to
supplyushwatertothebowl.Connecta3/4”(19
mm)I.D.reinforcedsuctionhosebetweentheseacock
and intake pump.
NOTE: An intake In-Line strainer (#163000) is
recommended to help avoid the accumulation of debris
in the intake pump.
2. Discharge Lines: Connect quality sanitation rated
11/2”(38mm)I.D.hose(#SFH)tothedischarge
tting on the toilet and connect to the treatment
system,holdingtank,ordischargethru-hulltting,
as appropriate.
TIP: To retain water in the bowl install a vented loop
in the discharge line.
*SpecifyVoltage
Allowsucient space atthe side andrear to connect
hoses.Ifspaceislimited,thebowlcanberotated90
degrees (a longer hose [#CH42] is required, contact
RaritanTechnicalSupport).
L910116jlc

3
NOTE: Discharge of raw untreated sewage is
restricted in all U. S. waters inside the three-mile limit.
“Y” Valves, if installed, must direct toilet discharge to
a USCG approved treatment system or holding tank
and must be secured in that position while inside the
three-mile limit.
WIRING
WARNING: RISK OF FIRE - The Crown Head must
be wired to a separately fused circuit with no other
electrical appliances on the circuit.
1. Measure wire distance from power source to toilet
andback,refertoSpecicationTableforproperwire
gaugeandcircuitbreaker/fusesizes.
12, 24 and 32 VDC Crown Head Units: Wire as per
FIG4.(Formomentarypushbuttonswitchoperation.)
2. Usingaprotectedcircuitthatisappropriateforthe
voltage of the unit, connect the positive lead from
thebatteryorpowersourcetothe“BAT”lugonthe
relay and connect a lead from the other relay lug to
thepositiveterminalontheCrownHeadmotor.
3. Connectgroundwirefromthebatteryorpowersource
to the negative terminal on the motor.
For VAC 120/240 Crown Head Units:  See
instructions with transformer units.
SYSTEM START-UP
1. Besureintakeanddischargeseacocksareopen.
2.RemovethecapfromtheConcentratereservoir
andpourin2oz.(59ml)ofConcentrate;llthe
remainder of the reservoir with fresh water and
replace the cap and siphon assembly.
3. RefertoOperationonpage1.Ifthetoiletdoesnot
ushproperly,orifwaterdoesnotenterthebowl
within10seconds,refertotheTroubleshooting
Section.Running the unit dry will damage the
intake pump.
Pushbutton
Switch
(164000BR) 3 Amp Fuse or
Circuit Breaker
Main Fuse or
Circuit Breaker
(See Specication Chart)
Pos Voltage from
Battery or DC Power
Panel
Battery
Lug
Solenoid Relay
(CDS)
#14 Awg
Wire
Ground
-(Neg)
Crown Head
+ (Pos)
Wiring the Crown Head (DC Unit with
Momentary Push Button Switch
PLUMBING
WARNING: HAZARD OF FLOODING
Toilets mounted at or below the waterline, at greatest
angle of heel, and connected to a Seacock/Thru Hull
Fitting(s) MUST have VENTED LOOPS installed
in toilet discharge plumbing and between raw water
intake pump and toilet bowl.
Install vented loops per manufacturer’s instructions.
Double clamp all below-waterline connections.
Whenever possible hose connections should be secured
using two all-stainless steel hose clamps. Integrity of
clamps,hosesandttingsshouldbecheckedperiodically.
Fittingsand90degreebendsshouldbekepttoaminimum
to maintain proper performance.
Crown Head with Raritan Sanitation Device,
Holding Tank and “Y” Valve
Above Waterline Installation Shown
To
Deck
Pumpout
Crown Head
Holding Tank
Discharge
Thru-Hull
and Seacock
Intake
Thru-Hull
and Seacock
“Y” Valve
Drawing Not to Scale
FIG 2 Crown Head with Raritan Sanitation Device
and Vented Loops
Sanitation Device
Crown Head
Intake
Thru-Hull and
Seacock
Discharge
Thru-Hull
And Seacock
Vented Loop
Vented
Loop
At or Below Waterline Installation Shown
Drawing Not to Scale
FIG 3
Sanitation Device
FIG 4
L910116jlc

4
Crown Head Exchange Units
CrownHeadExchangeUnitsareremanufactured
units available as a service to the customer. The
oldpumpandmotorassembly(LBA)aretakenin
tradeonaremanufacturedunit;thebowl,seat,lower
cover and discharge ttings are kept and reused.
WhenorderingdirectlyfromRaritan,acorecharge
isassesseduntiltheoldunitisreceivedbyRaritan.
Subject to parts and production availability,
exchange units are not always available for shipment.
ExchangeunitsincludetheLBAalongwithapackage
of fasteners, new joker valve, mounting strips and a
bowlgaskettoremountthebowltotheLBA.
NOTE: Pre-11/87 Standard LBA’s utilized a
apper valve on the discharge. If replacing this
model, please mention it when ordering; a special
discharge tting will have to be added to the order.
Breaker and wire sizes will have to be increased
- see Specications below.
CROWN HEAD SPECIFICATIONS
A. Nominal Voltage of Unit (Volts D.C.): 12 24 32
 For120/240VACunitsutilizingtherectied
 transformer,referto24VoltD.C.Specications
B. Amperage Draw @ Nominal Voltage 36 20 15
C. Circuit Breaker /Fuse Requirement (Amps): 50 30 20
D. Wire Gauge Sizes (AWG) Circuit Length,
Battery to Crown Head and Back: 0-15Ft. #6 #10 #10
      16-25Ft. #4 #10 #10
      26-50Ft. #2 #8 #10
      Over50Ft.RefertoABYC(E-9)Recommendations
E. Switch Wire Size:   0-50Ft. #14 #14 #14
Switch Wire Fuse Size (Amps): 3 3 3
F. Maximum Height of Discharge Vented Loop: 4Ft.FromBaseofToilet
H. Maximum Suction of Inlet Pump
 (AllowableHeightofToiletAboveWaterline): 3Ft.FromBaseofToilet
I. Duty Cycle:      30SecondsOn;120SecondsO
ONBOARD FRESHWATER USE: If you
would like to retrot your current Crown Head
for use with pressurized freshwater please contact
Raritan Technical Support.
L910116jlc

5
1. Poor pumpout, especially solids.
PROBLEM POSSIBLE CAUSE SOLUTION
TROUBLESHOOTING
WARNING: HAZARD OF ELECTRIC SHOCK - Before beginning any work on the Crown Head, be sure that all
power to the unit has been turned o and that the seacocks are in the CLOSED or OFF position.
NOTE: The following information reects the most probable causes and solutions to problems although not
every possible cause and solution is provided.
AnyquestionsregardingservicingoroperationoftheCrownHeadshouldbedirectedtoourTechnicalSupportDepartment
inMillville,NJorFt.Lauderdale,FL.Pleasehavemodelandserialnumberavailablebeforecalling.
L910116jlc
1A.Clogged discharge line.
1B. Plumbing restrictions, bends and ells.
1C. Clogged Vents.
1D. Mineral buildup in hoses and ttings.
1E. Low voltage
1F. Discharge pump (#CH120) wall not
intact.
1A. Be sure discharge seacock is open.
1B. Replumb to eliminate bends and ells.
1C. Clean holding tank vent and vented loop vents.
1D. Clean or replace aected parts. Replace hose if needed.
1E. Check voltage at toilet while toilet is running. If less
than nominal voltage of toilet (12, 24, or 32), check condi
tion of batteries and wire sizes. Check terminals and wire
connections for corrosion (heat at terminals and junctions
indicates a bad or corroded connection).
1F. Reposition pump wall behind macerating teeth cast in
housing cavity. Replace if necessary.
2. Poor water ow, especially at
front of bowl (or no water ow)
2A. Toilet not level. 2A. Raise rear of toilet; check with level.
2B. Restriction in intake line. 2B. Be sure seacock is open. Clear line-remove clog.
2C. Check ball (#CH12) stuck. 2C. Remove intake hose - poke eraser end of pencil into
intake nozzle of pump to free check ball.
2D. Intake Pump sucking air. 2D. Check all connections from intake thru-hull to
intake pump to be sure no air leaks are present.
2E. Low voltage. 2E. See 1E, above.
2F. Intake pump impeller worn or broken 2F. Replace impeller.
loose from center bushing.
2G. Clogged strainer. 2G. Clean debris from strainer.
3. Foul odors from toilet area. 3A.“Marine life” lodged in rim of bowl. 3A. Remove and ush bowl with pressure hose to remove all
material. Install strainer in intake line to avoid recurrence.
Fill reservoir with Raritan Cleans Potties (#1PCP22) and
use regularly.
3B. Permeated discharge hose 3B. Replace hose with Raritan SaniFlex Hose (#SFH).
3C. Sewage remaining in discharge line. 3C. Flush toilet longer; replace hose if permeated; reroute
hose making a shorter run, if possible.
3D. Concentrate reservoir empty. 3D. Rell with 2 oz. (59ml) Raritan Cleans Potties (1CP22)
and water.
4. Bowl lls while underway. 4. Pressure buildup at seacocks. 4. Close intake, then discharge seacock to
determine which is causing problem. If
intake, replace check ball and spring. If dis
charge, be sure the vent or vented loop is
clean. If intake, there is too much pressure on
seacock; contact Raritan Technical Support.
5. Concentrate tank does not
empty (or overows).
5A.Check valve malfunctioning. 5A. Remove and rinse check valve in warm water
and rein-stall. Should problem continue, replace check
valve. See page 7.
5B. Insucient water ow from pump 5B. Check waterow and correct as needed.
6. Water leaking from under unit. 6A. Leaking bowl gasket. 6A.Tighten (4) bowl mounting nuts (#1226B).
6B. Leaking front cover. 6B. Remove front cover (#CH18) and inspect O”ring
(#CH25) for damage. Replace “O” ring if necessary using Super
Lube (#SL1CC) to reassemble.
6C. Leak at sha seal. 6C. Check #CH59 seal and motor sha.
7. Loud noises from unit. 7A. Object jammed in macerator. 7A. Remove front cover and remove object.
7B. Motor bearings damaged by seal leak or 7B. Return motor to factory for servicing or replacement.
other water source.
8. Erratic operation/sluggish
running
8A.Worn motor brushes. 8A. Return motor to factory for servicing or replacement.
8B. Motor bearings damaged by seal leak. 8B. Return motor to factory for servicing or replace macerator
seal. If bearings are bad, exchange lower base.
8C. Low or inconsistent voltage 8C. See 1E above.

6
Part No. Description
1118  Lockwasher(4)  
1203B1  “O”Ring   
1222AW DischargeEllandFlange  
1222B  StraightDischarge  
1222BW StraightDischargeAssembly(Incl.1222B,
  CH90,CH92,[2]1115,C253,[4]CH27)
1226B  BowlMountingNut(4)  
1234 BowlGasket(tsallRaritantoilets)
1341  DischargeScrew(2)  
31-102  MotorShaftSeal
C253  JokerValve
CH102MW IntakePumpAssembly,complete
CH119MW DischargeImpellerAssy.(Incl.CH119M,
  [2]F149VT)
CH12  CheckBall
CH120  DischargePumpWall
CH121  Macerator
CH136  SiphonCapforShroudBottle
CH18W FrontCover(w/”O”ring)  
CH2  PumpBody(w/shaftseal)
CH25  FrontCover“O”Ring  
CH26  FrontCoverScrew(6)  
CH27  MountingScrew(4)  
CH291  Shroud(2pcs.)
CH29A  ShroudBottle(ConcentrateReservoir)
CH29A1W ShroudAssembly,Completew/bottle,cap
and siphon
CH336W SiphonAssembly,Complete(Incl.CH136,
  CH37,CH37E)
CH34  WoodruKey
CH37  SiphonTubing   
CH37E  SiphonCheckValve  
CH38  BowlStud(4)   
CH42  Hose    
CH43  S/SHoseClamp(2)  
OR
CH43P  NylonHoseClamps(2)
CH5VW PumpPlug,Vented(Incl.1203B1ORing)
CH50CW BowlElboww/SiphonIntake 
CH51  BaseScrew(4)   
CH52  RubberMountingStrip(2)notshown
CH53  PumpMountingScrew(4)
CH55A  BasePlate   
CH57  Slinger    
CH58  EndBellScrew(4)
CH59  SealwithStainlessSteelSpring
CH6  PumpCoverPlate  
CH7  PumpGasket
CH8  CheckValveSpring
CH90  DischargeAdapter
CH92  AdapterGasket
CHM*  Motor
Part No. Description
F149VT SetScrew(2)
G15 ImpellerWasher(2)
G13W PumpImpellerw/(2)G15
G2M ImpellerWearPlate
M23A Lockwasher(4)
M30 HexNut,Brass(2)
M31 FlatWasher,Brass(2)
RNI NylonBowlMountingWasher(4)
VCAP VinylCap(bowlnutcover)
MISCELLANEOUS RELATED PARTS
Part No. Description
1236AW BowlSpudAssembly
1237W Marine-sizeBowl,RoundTopRim(whiteonly),incl.
1236AW
1238SC Slow Close, Seat and Cover for Marine-size Bowl
(whiteonly)
1244W Household-style Bowl, Oval Top Rim available in
whiteorbone,includes1236AW
1245SCSeatandCoverforHousehold-styleBowlSlowClose
163000 In-LineStrainer
CDS* ContinuousDutySolenoidRelay
CHTT9 HoseClampfor11/2”I.D.Hose
1PCP22 CleansPotties22oz.
CSRK RepairKit(CentrifugalDischargeSeries)Includes:
CH25,CH92,1234,CH12,G13, CH8, CH37E,
RNI, CH120, C253, CH59, 31-102, CH7, G15,
1203B1andCH57
CDPUMPRK CrownHeadCDSeries&CHIIIntakePumpRepair
Kit(builtbefore4/95)Includes:1203B1,CH12,G13,
G2M,31-102,CH7andG15
CDDISRK CrownHeadCDSeriesDischargeRepairKit;
Includes:1234,CH120,CH57,CH92,C253,CH25
andCH59
CR1 DischargeImpellerandMaceratorAssy.(incl.CH120,
CH121,F149VT[2],andCH119MW)
164000BR HeavyDutyPushButton,Brass  
RHT4 InlineCheckValvefor11/2”I.D.HoseRTC*Raritan
O-delayTimer
RTCH24DA RectiedTransformer(for120or240VAC input)
SFH SaniexHose
SL1CC Super-Lube1/2oz.tube
TD90319 VentedLoop3/4”
TD90323 VentedLoop11/2”
TD90314W TruDesignAquaValvefor11/2”withtails
L910116jlc
CROWN HEAD PARTS LIST
(Quantities are one unless otherwise indicated)
Beforeordering,locaterequiredpartonexplodedpartsviewtobesureyouareorderingthecorrectpartforyourCROWNHEAD.
*Specify Voltage

7
7
L91 0116jlc
*Specify Voltage
or
CH43 for
S/S Clamp
CH43P for
Nylon Clamp
7
L910116jlc
*Specify Voltage
7
L91 0116jlc
M23A
C253
CH55A
G13W
CHM*
*Specify Voltage
CH136
CH37E
CH29A
CH291
crown head
EXPLODED PARTS VIEW
CENTRIFUGAL DISCHARGE SERIES
CH136
CH37
CR1
CH58
1118
CH51
CH42
L910116jlc
*Specify Voltage

8
LIMITED WARRANTY
  RaritanEngineeringCompanywarrantstotheoriginalpurchaserthatthisproductisfreeofdefects
inmaterialsorworkmanshipforaperiodofoneyearfromtheproduct’sdateofpurchase.Should
thisproductprovedefectivebyreasonofimproperworkmanshipand/ormaterialswithinthewar-
rantyperiod,Raritanshall,atitssoleoption,repairorreplacetheproduct.
1.TOOBTAINWARRANTYSERVICE,Consumermustdelivertheproductprepaid,togetherwith
adetaileddescriptionoftheproblem,toRaritanat530OrangeSt.,Millville,N.J.08332.When
requesting warranty service, purchaser must present a sales slip or other document which establishes
proofofpurchase.THERETURNOFTHEOWNERREGISTRATIONCARDISNOTACONDI-
TIONPRECEDENTOFWARRANTYCOVERAGE.However,pleasecompleteandreturnthe
ownerRegistrationCardsothatRaritancancontactyoushouldaquestionofsafetyarisewhich
couldaectyou.
2.THISWARRANTYDOESNOTCOVERdefectscausedbymodications,alterations,repairsor
serviceofthisproductbyanyoneotherthanRaritan;defectsinmaterialsorworkmanshipsupplied
byothersintheprocessofinstallationofthisproduct;defectscausedbyinstallationofthisproduct
otherthaninaccordancewiththemanufacturer’srecommendedinstallationinstructionsorstandard
industryprocedures;physicalabuseto,ormisuseof,thisproduct.Thiswarrantyalsodoesnotcover
damagestoequipmentcausedbyre,ood,externalwater,excessivecorrosionorActofGod.
3.ANYEXPRESSWARRANTYNOTPROVIDEDHEREIN,ANDANYREMEDYFORBREACH
OFCONTRACTWHICHBUTFORTHISPROVISIONMIGHTARISEBYIMPLICATIONOR
OPERATIONOFLAW,ISHEREBYEXCLUDEDANDDISCLAIMED.ALLIMPLIEDWAR-
RANTIESSUCHASTHOSEOFMERCHANTABILITYANDOFFITNESSFORAPARTICULAR
PURPOSE,IFAPPLICABLE,ASWELLASANYIMPLIEDWARRANTIESWHICHMIGHT
ARISEBYIMPLICATIONOFLAW,AREEXPRESSLYLIMITEDTOATERMOFONEYEAR.
SOMESTATESDONOTALLOWLIMITATIONSONHOWLONGALIMITEDWARRANTY
LASTS,SOTHEABOVELIMITATIONMAYNOTAPPLYTOYOU.
 4.UNDERNOCIRCUMSTANCESSHALLRARITANBELIABLETOPURCHASERORANY
OTHER PERSONS FOR ANY SPECIAL OR CONSEQUENTIAL DAMAGES, WHETHER
ARISINGOUTOFBREACHOFWARRANTY,BREACHOFCONTRACT,OROTHERWISE.
SOMESTATESDONOTALLOWTHEEXCLUSIONORLIMITATIONOFINCIDENTALOR
CONSEQUENTIALDAMAGES,SOTHEABOVELIMITATIONOREXCLUSIONMAYNOT
APPLYTOYOU.
 5.Nootherpersonorentityisauthorizedtomakeanyexpresswarranty,promiseorarmationof
factortoassumeanyotherliabilityonbehalfofRaritaninconnectionwithitsproductsexceptas
specicallysetforthinthiswarranty.
 6.Thiswarrantygivesyouspeciclegalrights,andyoumayalsohaveotherrightswhichvaryfrom
state to state.
SpecicationsSubjecttoChangeWithoutNotice  PrintedinU.S.A.
L910116jlc
530OrangeStreet,Millville,NJ08332USA
Telephone:856-825-4900 FAX:856-825-4409 
www.raritaneng.com
FortLauderdale,FL    
Telephone:954-525-0378 