Rcom Reptile MAX 60 User manual

Ver. 2.3
DIGITAL REPTILE INCUBATOR
REPTILE MAX 60
Love of life begins with "Rcom"
USER'S MANUAL
PUMP POWER
POWER INLET
PUMP POWER
POWER INLET

5. How to Clean
(1) Disassembling and Cleaning the Incubator 15
Caution : Caution mark against a fault that can cause damage, trouble, or failure of incubation.
Tip : References or useful suggestions in using Rcom product
Mark Explanation
Warning of actions which may be dangerous or cause damage to the incubator.
Prohibited.
Do not disassemble.
Do not touch.
It is necessary to keep.
Remove the power cord from outlet.
Ground Connection for preventing electric shock.
1. Introduction
(1) Rcom Reptile 60 Introduction 3 ~ 6
(2) Safety precautions
(4) Name & Function of Operation Parts
(3) Identification of Parts and Composition
7. Product Information
(1) Troubleshooting 18 ~ 19
(2) Specification
4. Function Settings
(1) Return to Factory Setting 11 ~ 14
(2) Temperature Setting
(3) Abnormal high, Low temperature alarm setting method
(5) Daily Temperature Range(D.T.G) setting method
(6) How to change Centigrade & Fahrenheit
(4) Abnormal high, Low humidity alarm setting method
2. Before use
(1) What is an Incubation Room? 7 ~ 8
(2) How to Assemble
3. Incubation
9 ~ 10
(1) Incubation Installation / Incubation Start
(2) Dew Condensation / Water Makeup / Candling
(3) Incubation Termination
6. Understanding
16
(1) Recommended temperature and humidity table by reptile during incubation
Introduction
Incubation
Product Information
Understanding
Function Settings
How to Clean
Before use
How to use Rcom Reptile MAX 60
The result of Hatching and Brooding can be changed by a large numbers of factors. Autoelex Co., Ltd.
& our distributors will not take any responsibility for ‘Loss of eggs or pet/animal lives’ under any
circumstances such as ‘Hatching/Brooding failures’, ‘User’s carelessness’, ‘Personal (un-certificated)
conversion / alteration’, ‘Arbitrary using out of the machine’s purpose’, ‘Electric power failure’, or
‘Malfunctioning’. Please be sure that the machine works without any problem before placing Eggs or
Pets(Animals). Also, we strongly recommend you to read the User’s Manual carefully to minimize of any
failure.
DIGITAL INCUBATOR
Contents
2

Rcom Reptile 60
Features of Rcom Reptile 60
[Main Function]
* Egg shaped reptile incubator.
* Automatic temperature control and setting function.
* Indicate several kinds of information with FND that visibility is excellent.
* Artificial intelligence automatically controlling its adjustment period according to the exterior environment of incubator.
* Reliability improvement by the 3rd generation temperature and humidity sensor of Swiss Sensirion Company.
* Clean and transparent large view window.
* Electronic control unit one touch removal method for providing cleaning convenience.
* Variable air control lever that can adjust incubator air content.
* Container tray of chamber organ that prevents egg from being dried and that individual management is possible.
* Daily temperature range setting function(D.T.G)
First of all, we would like to express our deep appreciation for all the customers who purchased Rcom Reptile
Incubator. Rcom Reptile Incubator was designed to be used easily and conveniently by the newest digital control
method for controlling optimal incubation environment automatically, however, in order to get the best incubation
result, at first, it is very important for users to have some incubation knowledge and right machine operation method.
Therefore, before suing incubator, be sure to read instruction manual. Rcom Reptile Incubator provides the best
incubation environment, however, it is necessary for users to observe and adjust each environment necessary for
incubation including egg kind, temperature and humidity management by incubation date, surrounding conditions
of incubator, and this product was made it possible to make the best setting for all the environments necessary for
incubation.
It is a function which artificially simulates the natural alteration of the ground temperature during the 24 h day
cycle. This function that can raise the incubation success rate of reptiles due to the optimal incubation
environment by raising temperature at the fixed time zone.
[Easy Function]
* Centigrade and Fahrenheit changing function.
* Alarm(buzzer) and indication function informing abnormal temperature and humidity(high and low temperature/high
and low humidity) for rapid exterior temperature change.
* Incubation Data memory function due to power failure and power failure alarm notification display function.
* Formation structure that the water drops(Drew Condensation) being formed on the view window don’t flow out to the
outside of incubator.
* Rotary Heater Support that that can adjust tension of heater conveniently.
* A sanitary instrument mechanism inhibiting double heat insulated structure and bacteria reproduction by combination
of Bottom and container tray through an innovative technology that can minimize parasitic bacteria by disusing
interior materials.
DIGITAL INCUBATOR
(1) Rcom Reptile 60 Introduction
1. Introduction
3

Electrical hazards Be careful the details below when you use.
Setting Cautions Be careful the details below when you use.
Cleaning Cautions Be sure to disconnect the electric cord from the outlet
before cleaning.
Do not pull the cord when
taking out the power cord, and
keep wet hands away from
connecting plug.
Do not use a damaged power
cord or loose outlet.
▶ Risk of electric shock or fire.
▶ Risk of electric shock or fire.
Do not insert multiple
connecting plugs in an outlet.
▶ Risk of fire or electrical
overload.
Never pull the plug out of the
outlet during the incubation
period.
▶Incubation will be interrupted.
Do not twist or crush electric
cord.
▶ Risk of electric shock or fire.
Clean the incubator by a soft
cloth with a neutral detergent.
Do not spray cleanser directly
on the incubator surface.
Do not use chemicals like wax,
benzene, alcohol, thinner,
aromatic, or lubricant, etc.
Brush away dust on the plug
with a dry cloth.
Wipe inside of incubator and
divider with antibacterial
cleanser to kill germ or bacteria
before use after long time
storage. Remove any foreign
substance on the fan and T/H
sensor with brush to guarantee
long time use. Make dry during
storage to prevent any
electrical problem.
▶ If you don't clean the inside of
incubator for a long time, dust
can cause some trouble or a fire.
Do not install under the direct
sunlight.
Do not install in dusty or dirty
environment.
▶ Risk of fire or interference
with the incubation process.
▶ Risk of damage or fire within
the incubator.
Do not install in excessively
cold or hot conditions,
cigarette smoke, etc.
Do not install in moist or
humid environment.
▶ Risk of interference with
the incubation process.
▶ Risk of fire or electric shock.
Do not use any other
non-standard parts except
those provided.
▶ Risk of damage or hatching
failure.
Please ensure that no small
objects get into
the holes on the incubator.
▶ Risk of electric shock or fire.
Do not disassemble or modify
the incubator in any way.
▶ Risk if electric shock or fire.
If the incubator sounds
strange or emits smoke
contact your service center.
▶ Risk of electric shock or fire.
If the incubator requires repair
disconnect from the power
supply and please contact to
your service center.
Clean the incubator thoroughly
before storing.
Install away from heat
sources.
▶ Risk of damage to the
incubator case and
interference with the
incubation process.
Do not turn the incubator
upside down.
▶ Water will pour out of the
incubator, and view window
can be dropped or damaged.
Ensure that the incubator is
installed on a stable surface
away from edges.
▶ Risk of damage to incubator
and eggs and user from
accidental knocks or drops.
Do not cover the ventilating
opening.
▶ Inner temperature can rise,
interrupting incubation.
Children should be supervised
to ensure that they do not play
with the appliance.
1. Introduction (2) Safety Precautions
DIGITAL INCUBATOR
4

View Window
View window Container tray Set
Main Controller
Power Cap
Ventilation Control Lever
Container Tray
(2pcs.)
Main controller / Sensor
Rated voltage and product serial No. are marked inside of power cover.
Be sure to check this before connecting power.
Digital temperature
and humidity sensor
Serial NO. was indicated on the left of main controller. Please make it not be contaminated.(Example:RCM0000000)
Power Cover
fixing bolt
Reptile Vermi(vermiculite)
170g x 2 sacks
Power Cord
(1pcs.)
Manual
PUMPPOWER
POWERINLET
생명사랑의 시작 “알콤”
DIGITALREPTILE INCUBATOR
REPTILE MAX 60
사용 설명서
Identification of Parts
Basic Components
Bottom body
Bottom body
Power Cap
1. Introduction (3) Identification of Parts
and Composition
DIGITAL INCUBATOR 5

Heater Operation Lamp
: Light on when working
①
Temp. Display
: Current Temperature Display
②
Humidity Display
: Current Humidity Display
③
Power Failure Alarm Function
: Light on when power failure (Cancel Button : OK)
④
Up Button
: Setting Temp. UP
⑤
Down Button
: Setting Temp. DOWN
⑥
Menu Selecting Button
: Setting Value check
⑦
● Name & Function of Operation Parts
①
④
⑤⑥ ⑦
② ③
Setting Mode: Press two buttons at the same time to go to Setting Mode.
Select Menu / Quick Movement / Cancellation / Setting value check during incubation
Value +
Value - / Factory Initialization
● Function Key Press buttons at the same time to go to setting mode.
Function Temp.
26.1℃
tEP HI LO
0℃0℃ ℃
℃
/ ℉
Abnormal low
temp. alarm
Abnormal high
temp. alarm Centigrade / Fahrenheit
ON
dtg
Daily temp.
range set
70%
LO
Abnormal low
humi. alarm
95%
HI
Abnormal high
humi. alarm
Dispaly
Default Setting
Reptile MAX 60 doesn’t have automatic
humidification function.
Name & Function of Operation Parts
1. Introduction (4) Name & Function of
Operation Parts
DIGITAL INCUBATOR
6

How to Assemble
Incubation room? It means the place where the incubator is installed and operated, and as it has much effect on
incubation rate according to the environment of incubation room, it is good to install incubator at the place where
there is little noise and vibration in the vicinity and the temperature range isn’t severe in the temperature of 22~25℃
(71.6~77℉). In particular, as there are many cases that the temperature falls rapidly in the nighttime differently
from the daytime, it is necessary to check certainly, and during daytime, incubator must not be exposed directly to
the sunlight.
▶Unpack incubator and separate each part to do assembly
and check if there is some omission or damage
(Don’t throw away product box to utilize it for safe product
keeping.)
When installing reptile incubator, in case that the temperature of incubation room is higher than its set
temperature, the temperature control of incubator inside may not be done normally. The set temperature
of incubation room should be around 4℃(7.2℉) lower than incubator set temperature.
REPTILE MAX 60 Incubator doesn’t have any automatic
humidity control function. It is recommendable to incubate
by testing if its required humidity is kept after mixing reptile
vermi and water into container tray rather than incubating
immediately and raising temperature up to the incubating
temperature.
▶Mix water 700~800cc with a bag of reptile vermi per one container tray and pour into 40~45mm height.
▶Adding water to vermiculite, inner incubator humidity shall
be increased by 15~20%. Even if the humidity which is
shown on the display window is higher or lower (15-20%)
compare to best incubation condition, that does not really
effect on hatching rate. If hatching is failed, check the
condition of eggs.
It is possible to purchase the vermiculite for reptile
incubation separately.
40~45mm
700~800cc
What is an Incubation Room?
2. Before Use (1) What is an incubation Room?
(2) How to Assemble
DIGITAL INCUBATOR 7

▶Incubation humidity depends on the quantity of the water mixed with reptile vermi, surrounding temperature and
humidity, and incubator set temperature. Please check the moisture state of reptile vermin every two weeks.
▶Fill the tray with vermi, and bury the half
of eggs.
▶Insert container tray carefully in the bottom
body.
▶Put sensor line into container tray furrow and
be sure to close all covers of tray and sight glass.
In case that the sight glass isn’t closed
completely, temperature doesn’t go up.
Be careful.
It is not good for the vermiculite to be reused after an incubation term incubation. The incubation rate will
fall because of bacterial contamination. [It might be possible to purchase the vermiculite at the place you
purchased the incubator.]
After the egg deposition, it is recommended
to lay the eggs in the incubator without
delay. Moreover we commend to mark
the top side of the eggs to make sure
the topside will always be up during t
he incubation process.
In case that the reptile vermi was completed dried, it may be in very dry state by absorbing the surrounding
humidity of incubator inside and egg. It is good to start after understanding the required environment for
each reptile kind and making previous test if incubation environment is proper to minimize incubation failure.
2. Before Use (2) How to Assemble
DIGITAL INCUBATOR
8
Marking
CAP

PUMPPOWER
POWERINLET
PUMPPOWER
POWERINLET
3. 부화
Preparation for Incubation / How to Start Incubation
▶Open power cap to plug-in and close power
cap again to lock bolt.
▶In case of connecting power cord of incubator, incubation starts at the existing set temperature and humidity.
[temperature of initial shipment 26.1℃(78.98℉)]
Power Cord
When locking bolt, be careful for cord
not to be trapped in the power cap.
Open power cap to find the sticker
indicating a rated voltage on the ⓐ
that was attached to the main body.
It is necessary to plug-in after checking
if power supply voltage to use is proper.
There can be some odor the first time you use incubator, which is normal.
▶The first time you connect power, FND light will blink and
pump will work for about 2sec. Then, incubator version
will be indicated on FND for about 1 sec.
▶After version indication, buzzer sounds for about 15sec.
At the same time, present temp. & humiditydisplayed and
power failure alarm indication ⓐis blinking.
▶Press button to remove buzzer and alarm indication. (Buzzer will be removed automatically after 15sec.)
※The artificial intelligence system memorizes and classifies ambient conditions for keeping optimum temperature,
and temperature can move up slowly at the first stage.
※Notice of Power Failure : If power is turned off and then
on again because of power failure or by mistake, first dot
will blink.
▶It indicates present temperature and humidity of incubator, and it goes up to the set temperature value in 1~2
hours. (No humidity control function)
Quick Start : If you just connect power,
it automatically starts incubation with factory setting.
[Factory setting : Temperature 26.1℃(78.98℉)]
Please perform incubation “test run“ to check all functions before incubating with real eggs.
Power
Cord
ⓐ
3. Incubation (1) Preparation for Incubation /
How to Start Incubation
DIGITAL INCUBATOR 9

▶There is no specified ON or OFF button on the incubator. Just take off the power cord after hatching.
▶It is not necessary to do Incubator Initialization with REPTILE MAX 60 incubator after hatching. Just connect
power again when you want to start incubation again.
▶This is a naturally occurring phenomenon when there is a significant difference in temperature between inside
and outside of the incubator during incubation period.If this occurs, water may form in inside bottom of the
incubator(bottom part).
Do not place any goods near the incubator.
Be careful for eggs not to be lifted and for shocks not
to be given.
▶Refill water into each container tray once a month.
▶Pour warm water of 300cc on the edge of each container
tray carefully in order for water not to be touched to egg
and sensor.
Water Makeup
▶Please candle with an egg candler once a week. Open the
cover of sight glass and container tray and flash a light
with a egg candler to candle egg. Remove infertile eggs
or incubation-stopped eggs.
Candling
Egg candler for exclusive use - See Rcom homepage.
Incubation Termination
Dew Condensation
3. Incubation
(2) Dew Condensation / Water Makerup / Candling
(5) Incubation Termination
DIGITAL INCUBATOR
10

PUMPPOWER
POWERINLET
PUMPPOWER
POWERINLET
▶Unplug power cord. Replug during button is pressed.
Then, "rSt AL" will indicated in display, and incubator
return to factory setting. (Default setting)
▶Press and button at the same time then “ tEP ”
will be indicated for about 0.5sec. and then temp display
will blink.
▶When temperature indicator flickers, press button or
button each to increase or decrease temperature
to 0.1℃level. [Default setting : 26.1℃(78.98℉)]
▶In case of pressing button after changing into wanted
value, temperature value is saved and “HI” is displayed
(abnormal high temperature alarm) as a next step at
temperature display window for 0.5 seconds and its set
value flickers.
※In case of not wanting to change setting, press button to go to the next step.
Step 2
Step 1
▶This function is for return incubator to factory setting.
Power Cord
HOLD
Factory Setting Display
When releasing from the factory, temperature was corrected to be optimized according to international
standard. If necessary, recorrection is possible, however, it isn’t desirable for users to correct it directly.
In case that correction is necessary, please contact Rcom homepage (www.Rcom.co.kr→data center →
Instruction manual categoty) or place where you purchased to inquire about it. As low price thermometer and
hygrometer easy to purchase in the open market have much deviation of estimate value, it is desirable to
use corrected thermometer and hygrometer for exclusive use. [thermometer and hygrometer for exclusive
use – See Rcom homepage]
Return to Factory Setting
DIGITAL INCUBATOR
4. Function Settings
11
(1) Return to Factory Settion
(2) Temperature Setting
Temperature Setting

※It displays that it was 3℃(5.4℉) higher than incubation set
value during incubation.
EX :
EX : ※It displays that it was 2℃(3.6℉) lower than incubation set
value during incubation.
▶In case of pressing button after changing into wanted
value, alarm set value is saved and “LO” is displayed
(abnormal low temperature alarm) as a next step at
temperature display window for 0.5 seconds and its set
value flickers.
▶When the alarm set value flickers, press or
button each to increase or decrease its set value to 1℃
level. [Default setting : OFF = 0℃(0℉)]
▶In case of pressing button one time at the temperature
set method stage, “HI” is displayed at the temperature
window for 0.5 seconds and the alarm set value flickers.
Abnormal high temp. alarm setting method
Abnormal high temperature alarm function?
It is a function informing users of that the temperature of incubator inside raised because of abnormal
temperature, and in case that the surrounding temperature of incubation room is higher than the set
temperature of incubator, it is continuously alternated ringing buzzer and displaying set temperature range
(example: 3℃) on the temperature window. After that, even though temperature is recovered to the normal
state, it keeps ringing buzzer and flickering repeatedly until it is cancelled by pressing OK button.
▶In case of pressing button after changing into wanted
value, alarm set value is saved and “HI” is displayed
(abnormal high humidity alarm) as a next step at humidity
display window for 0.5 seconds and its set value flickers.
Abnormal low temp. alarm setting method
In case of abnormal low temperature: In case of abnormal low temperature, "LO" is displayed at humidity
display window and it is the same as at the abnormal high temperature.
▶In case of pressing button one time at the abnormal
high temperature set method stage, “LO” is displayed at
the temperature window for 0.5 seconds and the alarm
set value flickers.
▶When the alarm set value flickers, press or
button each to increase or decrease its set value to 1℃
level. [Default setting : OFF = 0℃(0℉)]
Step 3
Step 4
Step 5
Step 6
(3) Abnormal high, Low temp.
alarm setting method
4. Function Settings
DIGITAL INCUBATOR
12

▶In case of pressing button after changing into wanted
value, alarm set value is saved and “dtg” is displayed
(daily temperature range) as a next step at humidity display
window for 0.5 seconds and its set value flickers.
Abnormal low humi. alarm setting method
In case of abnormal low humidity: In case of abnormal low humidity, "LO" is displayed at temperature display
window and it is the same as at the abnormal high humidity.
▶In case of pressing button one time at the abnormal
high humidity set method stage, “LO” is displayed at the
humidity window for 0.5 seconds and the alarm set value
flickers.
▶When the alarm set value flickers, press or
button each to increase or decrease its set value to 1%
level. [Default setting : RH 70%]
REPTILE MAX 60 Incubator doesn’t have any automatic humidity control function. But, it has an alarm function
informing it to the users in case of getting out of necessary humidity range during incubation. In case that alarm
set humidity range is too sensitive, frequent alarm may ring, however, in case of cancelling this function, just OFF
alarm function. (See step 7~10) ※Abnormal humidity alarm rings for 15 seconds only in the initial occurrence.
▶In case of pressing button after changing into wanted
value, alarm set value is saved and “LO” is displayed
(abnormal low humidity alarm) as a next step at humidity
display window for 0.5 seconds and its set value flickers.
▶When the alarm set value flickers, press or
button each to increase or decrease its set value to 1%
level. [Default setting : RH 95%]
▶In case of pressing button one time at the abnormal
low temperature set method stage, “HI” is displayed at the
humidity window for 0.5 seconds and the alarm set value
flickers.
Abnormal high humi. alarm setting method
Abnormal high humidity alarm function?
It is a function informing users of that the humidity of incubator inside raised because of abnormal humidity,
and in case that it is higher than the set humidity of incubator, it is continuously alternated ringing buzzer and
displaying set humidity range(example: 5%) on the humidity window. After that, even though temperature is
recovered to the normal state, it keeps ringing buzzer and flickering repeatedly until it is cancelled by pressing
OK button. Step 7
Step 8
Step 9
Step 10
※It displays that its inside humidity was temporarily higher than abnormal
high humidity alarm set value(RH 95%) during incubation.
※It displays that its inside humidity was temporarily lower than abnormal
low humidity alarm set value(RH 70%) during incubation.
EX :
EX :
DIGITAL INCUBATOR
(4) Abnormal high, Low humi.
alarm setting method
4. Function Settings
13

▶In case of pressing button one time at the abnormal
low humidity set method stage, “dtg” is displayed at the
temperature window and its set value flickers.
▶When the alarm set value flickers, press or
button each to change to “ON” ↔ “OFF” [Default setting : ON ]
▶In case D.T.G was already set, for 3 hours of 24 hours, the inside temperature of incubator goes up 1.5℃more
than set value, and “dtg” is displayed with temperature alternately at the temperature display window.
▶In case of pressing button after changing into wanted value, changed set value is saved and “C . F”
(Centigrade /Fahrenheit)” is displayed as a next step at temperature window for 0.5 seconds and LED of “℃”
flickers.
Daily Temp. Range(D.T.G) setting method
▶After selecting wanted display, press button to be
set. [Default setting : ℃]
How to change Cels. & Fahr.
▶Whenever pressing or button, LED flickers into
"℃" ↔ "℉" alternately. [Default setting : ℃]
℃= 5/9 (℉ - 32)
Step 11
Step 12
Step 13
Step 14
▶ Daily temperature range (D.T.G)?
It is a function artificially making the highest time zone of
temperature by sun at the natural condition, and it is a
function that can raise the incubation success rate of
reptile by the optimal incubation environment by raising
temperature at the fixed time zone.
(5) D.T.G setting method
(6) How to change Cels. & Fahr.
4. Function Settings
DIGITAL INCUBATOR
14

▶In case of immediately turning off the incubator progressing
incubation with a high humidity and leaving it at the state
that the cover was closed, as the humidity remaining in
the inside evaporates and is attached to the electric device,
it may be a cause of breakdown. Be sure to remove inside
humidity after getting off transparent window to use machine
the most safely.
▶Remove main controller from view window.
▶Sensor unit is connected to the connector to be changed
easily in case of breakdown.
▶Wash container tray, main body(bottom)
cleanly with warm water and dry them
at cool place.
▶Assemble again in the opposite order separated to keep it.
▶Wash the outside of main controller,
transparent window and sensor cleanly
with a soft cloth.
Be sure to take off power cord before cleaning the
incubator.
Never wash sensor unit with water. It may be a cause
of breakdown, and it may decrease the life span of sensor.
Power cord
Sensor
Unit
Disassembling and Cleaning the Incubator
DIGITAL INCUBATOR
5. How to Clean (1) Disassembling and
Cleaning the Incubator
15
PUMPPOWER
POWERINLET
PUMPPOWER
POWERINLET

North American King Snake
North American Milk Snake
60-65 days 28.3˚C / 83˚F 90%
60-65 days 28.3˚C / 83˚F 90%
North American Rat Snake 60-65 days 28.3˚C / 83˚F 90%
Corn Snake 55-60 days 29.4˚C / 85˚F 85%
King Snake 60-65 days 28.3˚C / 83˚F 90%
Amazon Tree Boa 40-50 days 31.1˚C / 88˚F 95%
Python 60-65 days 32.2˚C / 90˚F 90%
Iguana Green Iguana 73-80 days 29.4˚C / 85˚F 85%
Bearded Dragon Lizard 60-70 days 28.9˚C / 84˚F 85%
Uromastyx 55-65 days 33.9˚C / 93˚F 92% 1.5˚F/3hour
Chinese water dragon 60-75 days 29.4˚C / 85˚F 85%
Tegu 60-70 days 28.3˚C / 83˚F 90%
Lizard 50-60 days 30.6˚C / 87˚F 87%
Day Gecko 50-65 days 27.8˚C / 82˚F 75%
Gecko 50-55 days 29.4˚C / 85˚F 88-90% 1.5˚F/3hour
Alligator (Mississippiensis) 63-84 days 31.7˚C / 89˚F 95%
Crocodile (Crocodylus porosus) 89-95 days 30.6˚C / 87˚F 95%
Other Unknown Reptile 50-90 days 30.6˚C / 87˚F 85%
Alligator
Reptile Grouping SPECIES INCUBATION PERIOD TEMPERATURE HUMIDITY DAILY TEMPERATURE GAP
Chameleon Veiled Chameleon 145-180 days 26.1˚C / 79˚F 80%
Box Turtles 70-80 days 27.8˚C / 82˚F 85%
Sea Turtle 58-62 days 29.4˚C / 85˚F 95%
Painted Terrapin Turtle 72-80 days 29.4˚C / 85˚F 95%
Snapping Turtle 60-85 days 29.4˚C / 85˚F 95%
Turtle
Desert Tortoise 85-90 days 30.6˚C / 87˚F 80%
European Tortoise 56-84 days 30.6˚C / 87˚F 75%
Mediterranean Tortoise 56-70 days 30.6˚C / 87˚F 75%
Tortoise
Snake
Lizard
※The recommended environmental conditions as the reptiles may differ slightly.
Recommanded temp. and humi. table by reptile during incubation
DIGITAL INCUBATOR
(1) Recommanded temp. and humi.
table by reptile during incubation
6. Understanding
16

No signs of power
to the incubator.
▶Try to plug-in again.
▶Check other electric and electronic product
nearby.
▶Check after moving to other socket.
▶Check if power cord was connected well.
▶Check power failure.
▶Check if plug is defective.
When temperature
is too high /
When temperature
is too low
When humidity
is too high /
when humidity
is too low
▶Check set temperature.
▶Check if FAN for air circulation doesn’t rotate.
▶Try to make factory initialization. [See 11 page]
▶Adjust set temperature to wanted temperature.
▶Unplug from socket and separate main
body to clean FAN area for air circulation
with a brush or writing brush.
▶Refill water sufficiently.
<when low>
▶Please add water to reptile vermi
(vermiculite) for eggs not to be wet.
[See 10 page]
▶Check if foreign substance was inserted
and close it again.
<when high>
▶Adjust environment of incubation room.
[See 7 page]
▶Try to make factory initialization. [See 11 page]
<When low>
▶Check if reptile vermin(vermiculite) contains
water.
▶Check if sight window closed well.
<When high>
▶Check surrounding environment.
▶Check if tray inside or main body(bottom)
contains water.
▶Remove all the objects put on the incubator.
▶Move incubator to the safe place to install.
▶Unplug from socket and separate main
body to clean FAN area for air circulation
with a brush or writing brush.
▶Check if there is some other object on the
incubator.
▶Check if there is some vibration on the
floor or it was installed on the desk.
▶Check if some foreign substance was
attached to FAN area after incubation.
It is normal that the
machine emits some
sounds because it
uses air circulation
fan for working.
The machine makes
some noise.
▶As reptile incubator operates at high
humidity, there is some dew on the sight
window. It isn’t a breakdown but natural
phenomenon.
▶Please install under the condition of
incubation room.
Water leaks from
the machine.
* In case of keeping
at high humidity, there
may be some dew.
Troubles Expected Causes (Possibility) Countermeasures
Please perform incubation “test run“ to check all functions before incubating with real eggs.
For more detailed self-diagnosis, see Rcom homepage “SELF DIAGNOSIS” category.
Troubleshooting
All our Rcom digital products of Autoelex Co., Ltd. are made by precision systems under strict quality control. But
occasionally some defective products are found on the way of their distribution.If any problem occurs, then please
contact Autoelex service center or distributorsin your country. We will do our best to solve the problems, if any,
for you. This product is designed in modular mode, so for its repair, if any, a qualified person can replace the part
concerned with ease.
* Customer Service : 82-55-337-2560 ＊E-mail Receipt : [email protected]
DIGITAL INCUBATOR
7. Product Information (1) Troubleshooting
17

To provide the best warranty service, please register your product serial number on our website.
Refer to website for how to register
※Product Registration Procedures
If you are a new member of Rcom, you need to log in our website at www.Rcom.co.kr
1. Click “SIGN UP” on top of the right corner.
2. Fill out the information on the blanks.
If you already registered your information on the Rcom website, please log in to
www.Rcom.co.kr.
1. Click “Login” on top of the right corner.
2. Select “Customer” and click “Register Products”.
3. Fill out the information on the blanks.
You will need below information to register on our website.
1. Your name
2. Your (home/company) address & Email address, country
3. Your product(model) name & Serial number
4. Date of purchase & Name of purchased shop you bought from
1-1 Name : Rcom Reptile MAX 60
1-2 Model : MX-R60
Specification
AC 100~120[V], 50/60[Hz] / AC 220~240[V], 50/60[Hz]
Temp. Control Range
Outside
Environment
Temp.
20 ~ 42[℃] /
68 ~ 107.6[℉]
Optimal range : 22 ~ 25[℃] / 71.6 ~ 77[℉]
(Low) 20[℃] / 68[℉] (High) 26[℃] / 78.8[℉]
Power Consumption Average 15[W] Max. 48[W]
60[eggs] (Different from the species of egg)
Product Size
FUSE Standard 250[V] 2.0[A] (Ø5*20[mm])
(W)370×(L)231×(H)209[mm]
Product Weight 2.8[Kg](N.W) / 4.3[Kg](G.W)
Capacity
Power
Rcom Incubator Series
Rcom PRO MINI
Package (PX-03S)
Rcom KINGSURO
MAX 20 (MX-SURO)
Rcom REPTILE
MAX 90 (MX-R90)
Rcom DIGILOG2
(PX-V2)
Rcom REPTILE
PRO 230 (PX-R230)
PUMPPOWER
POWERINLET
WATER
W
A
T
E
R
P
U
LL
OP
EN
It is possible to check additional information at Rcom homepage (www.Rcom.co.kr).
DIGITAL INCUBATOR
7. Product Information (2) Specification
18

Compensation content
Consumer damage type
In case of the naturally occurred breakdown in performance and function during normal use
Breakdown in performance and function due to consumer’s intention or fault
Credit repair
Product Warranty
Product Name :
Date of sales : year month date
Name of customer : Telephone Number : Mailing address :
Place of purchase : Telephone Number : Mailing address :
Consumer compensation for the damage
● When requesting repair, as you should show this warranty that purchase date was indicated
to get satisfactory service, we request you to keep it well.
within
warranty period after warranty period expired
Free repair Credit repair
In case of the breakdown caused by Natural disaster (fire, damage from sea wind, gas,
earthquake, damage from storm, etc.)
In case of exchanging the consumable parts that are worn normally during use
In case of the breakdown caused by power problem and connector defect
In case of the breakdown because the person who isn’t a repair technician of main office
or agency repaired or recomposed
In case that the breakdown was made by the external cause, not other product’s own defect
In case of the breakdown caused by different use of rated voltage
In case of the breakdown caused by the use of the consumables and optional products
undesignated by this company
In case of the breakdown or damage caused by the falling during movement
Breakdown occurred by no cleaning / Breakdown occurred by not using distilled water /
Breakdown occurred when incubator was used for development(brooding) /
Breakdown occurred by wrong machine operation /
Breakdown occurred by using with the method that wasn’t suggested in the instruction /
the case that consumer fault is obvious.
* Customer Service : +82. 55. 337. 2560 ＊E-mail contact : [email protected]
Please see detailed consumer damage compensation regulation
at “Customer Center” of Rcom homepage www.Rcom.co.kr.
The result of Hatching and Brooding can be changed by a large numbers of factors. Autoelex Co., Ltd.
& our distributors will not take any responsibility for ‘Loss of eggs or pet/animal lives’ under any
circumstances such as ‘Hatching/Brooding failures’, ‘User’s carelessness’, ‘Personal (un-certificated)
conversion / alteration’, ‘Arbitrary using out of the machine’s purpose’, ‘Electric power failure’, or
‘Malfunctioning’. Please be sure that the machine works without any problem before placing Eggs or
Pets(Animals). Also, we strongly recommend you to read the User’s Manual carefully to minimize of any
failure.
7. Product Information (2) Specification
DIGITAL INCUBATOR 19

www.Rcom.co.kr




SELLER MANUFACTURER
● OFFICE : 218, Sangdong-ro, Sangdong-myeon,
Gimhae-si, Gyeongsangnam-do, 50805 Korea
● TEL : [phone]
● FAX : [phone]
● E-MAIL : [email protected]