RealFlame IGNITE XLF50 User manual

XLF50IK - VERSION 1
ASSEMBLY & INSTALLATION MANUAL
IGNITE
XLF50
INSTALLATION KIT

REAL FLAME IGNITE XLF50 INSTALLATION KIT

1
TABLE OF CONTENTS
1. Fasteners Included............. 2
2. Tools Required................ 2
3. Enclosure Assembly ............ 3
3.1. Step 1 .................. 3
3.2. Step 2 .................. 3
3.3. Step 3 .................. 4
3.4. Step 4 .................. 4
3.5. Step 5 .................. 5
3.6. Step 6 .................. 5
3.7. Step 7 .................. 6
4. Enclosure Wall Mounting........ 7
4.1. Step 1 .................. 7
4.2. Step 2 .................. 8
4.3. Step 3 .................. 9
4.4. Step 4 ..................10
4.5. Step 5 ..................11
4.6. Step 6 ..................12
4.7. Step 7 ..................13
5. Dimensions ..................14
6. Warranty ....................15
6.1. Australia Warranty Claims ...16
6.2. NZ Warranty Claims .......16
7. Notes ......................17

2
1. FASTENERS INCLUDED
2. TOOLS REQUIRED
The Real Flame Ignite XLF50 Installation
Kit can be installed using a power drill,
phillips head bit, 3mm wood drill bit
and an M6/10mm socket bit. These
tools are not supplied with the kit.
4X
38X
4X
4X
Phillips
3mm
10mm

3
3. ENCLOSURE ASSEMBLY
3.1. STEP 1
After unboxing the XLF50 unit, remove
the 4X trim pieces attached to the top,
bottom and sides of the unit with 12 X
screws. Retain 4X screws, as these will
be used later.
3.2. STEP 2
Once the trims have been removed, lay
the unit face down on a soft surface such
as a rug or carpet.
4X

4
3.3. STEP 3
Install the Bottom Panel of the Enclosure
using 4X screws supplied with the XLF50
unit (removed from trims in Step 1),
routing power cord through the cut out in
the Bottom Panel.
3.4. STEP 4
Attach 2X Side Panels to Bottom Panel
using 8X screws.
8X
4X

5
3.5. STEP 5
Attach Top Panel to Side Panels using
8X screws.
3.6. STEP 6
Attach Mounting Frame to Top and
Bottom Panels using 10X screws.
8X
10X

6
3.7. STEP 7
Attach 3X Mounting Rails to Mounting
Frame using 10X screws.
ENCLOSURE ASSEMBLED,
PROCEED TO WALL MOUNTING.
10X

7
4. ENCLOSURE WALL MOUNTING
To aid in a successful installation, it is
advised that two people help when wall
mounting the Enclosure.
4.1. STEP 1
First, locate 2X timber studs on the
intended installation wall.
Example Wall

8
4.2. STEP 2
Using two people - lift Wall Mounting
Hanger into place, aligning slots with
the previously located studs, use slot
adjustment to centralise the Hanger as
necessary. For optimal viewing height,
measure 730mm from the bottom of the
Wall Mounting Hanger to the ground.
Use the spirit level provided with the
XLF50 unit to ensure the Wall Mounting
Hanger is level, before marking the wall
in 4X places to drill pilot holes.
NOTE
The Enclosure can be mounted at any
height if desired, under the condition that
room is left for the power cord to run
below it.
730mm

9
4.3. STEP 3
Using marks from the previous step, drill
4X pilot holes to a depth of 50mm using
a 3mm drill bit.
3mm
X4

10
4.4. STEP 4
Using two people - lift Wall Mounting
Hanger into position, aligning slots
with previously drilled pilot holes. Drive
4X M6 X 50mm screws with 4X washers
into studs using M6/10mm socket bit.
Do not drive screws to full depth at
first, to allow for small adjustments as
necessary. Once desired positioning is
achieved, drive screws to full depth.
X4
1
0mm
X4

11
4.5. STEP 5
Using two people - lift assembled
Enclosure into place on Wall Mounting
Hanger. Locate the top hanger into
the top of the Mounting Frame and the
bottom hangers into the 3X Mounting
Rails.
Side View

12
4.6. STEP 6
Secure the Enclosure to the Wall
Mounting Hanger with 2X screws.
2X

13
4.7. STEP 7
Ignite XLF50 Installation Kit has now
been assembled and wall mounted.
Please refer to the Ignite XLF50
instruction manual for further installation
and operating instructions.

14
5. DIMENSIONS
1297mm
174mm
401mm

15
6. WARRANTY
The benefits provided to you under the
following warranty are in addition to
any other rights and remedies available
to you under the law.
1. Warranty
If during the first 2 years from the date
of purchase (Warranty Period), there is
a defect in the Installation Kit (Product),
due to improper workmanship or
material, Glen Dimplex will replace or
repair the Product without charge. Any
replacement Product is warranted only
for the time remaining on the original
Warranty Period or the Parts Warranty
Period as relevant.
2 . Registration
You must register to receive the benefit of
this warranty by completing the warranty
registration on our website within 30
days of purchase of your Product.
Australia:
https://www.realflame.com.au/en-au/
support/warranty
New Zealand:
https://www.realflame.co.nz/en-nz/
support/warranty
3 . Exclusions
Glen Dimplex is not obliged to replace
or repair the Product under clause 1 if:
(a) it has been improperly stored,
installed, assembled, used, operated
or repaired, or damaged, abused,
tampered with, altered (without our
written approval), or not maintained in
strict accordance with our installation
and operating instructions; or
(b) it has been installed in an outdoor
setting.
4 . Limit of Liability
The warranty provided under this
warranty is limited to replacement
or repair of the Product only, at our
option. To the extent permitted by law,
Glen Dimplex excludes liability for
consequential loss or any other loss or
damage caused to property or persons
arising from any cause whatsoever, and
damage arising from normal wear and
tear.
5 . Claiming under the Warranty
In order to claim under this warranty
you must, within the Warranty Period or
the Parts Warranty Period (as relevant),
contact Glen Dimplex, providing the
original proof of purchase and the
details below:
Supplier Name____________________
Date Of Purchase __________________
Model / Serial Number_____________
This warranty does not cover the cost
of claiming under the warranty or
transporting the Glen Dimplex Product to
and from the supplier.
Our goods come with guarantees
that cannot be excluded under the
Australian Consumer Law and Consumer

16
Guarantees Act 1993 (New Zealand).
You are entitled to a replacement
or refund for a major failure and for
compensation for any other reasonably
foreseeable loss or damage. You are
also entitled to have the goods repaired
or replaced if the goods fail to be of
acceptable quality and the failure does
not amount to a major failure.
6.1. AUSTRALIA WARRANTY CLAIMS
If you would like to speak to someone
about your Product or claiming under
this warranty, please contact the Service
Warranty Desk on 1300 554 155.
Glen Dimplex Australia Pty Ltd
ACN 69 118 275 460
Head Office: 8 Lakeview Drive,
Scoresby 3179 Victoria, Australia
Phone: [phone]
Fax: [phone]
Email: [email protected]
6.2. NZ WARRANTY CLAIMS
If you would like to speak to someone
about your Product or claiming under
this warranty, please contact the Service
Warranty Desk on 0800 666 2824.
Glen Dimplex New Zealand Ltd
Head Office: 38 Harris Rd, East Tamaki
Auckland 2013, New Zealand
P.O Box 58473
Phone: [phone]
Fax: [phone]
Email:info@realflame.co.nz

17
7. NOTES

18
Glen Dimplex Australia Pty Ltd
8 Lakeview Drive,
Scoresby Victoria 3179
Australia
T: 1300 556 816 | F: 1800 058 900
Email: [email protected]
www.glendimplex.com.au
Glen Dimplex New Zealand Pty Ltd
38 Harris Rd,
East Tamaki Auckland 2013
New Zealand
P.O. Box 58473
T: 09 274 8265 | F: 09 274 8472
Email: info@realflame.co.nz
www.glendimplex.co.nz