ReelCraft D9200 OMP User manual

1. Models designed for fuel are coded with the prefix “F” i.e., “FD9400 OMP.”
Check name plate on the reel before installing.
2. Do not use reel at higher pressures or temperatures than listed on the back
of this bulletin.
3. Remove all spring tension before beginning dissassembly process.
4. Reel spring motor case is permanently sealed. Any attempt to remove the
spring motor may cause serious injury.
SAFETY
INSTALLATION: The swivel union is packed separately in the reel carton, use teflon tape to assure a satisfactory seal. A flexible hose
connection must be used between the hose reel inlet and the source of supply to prevent possible misalignment and
binding. Non flexible connections will void the warranty, pressure rating of inlet hose must be equal to or more than
the pressure rating of the reel. Consult factory for proper spring when installing reels above 16 ft.
LUBRICATION: Hose reel spring and bearings are factory lubricated and require no further lubrication.
REPLACING HOSE: 1. Wind spool flange clockwise-facing swivel-until spring is tight.
2. Back off three turns and latch.
3. Insert hose through roller guide.
4. Connect hose fitting to female outlet ell.
ADJUSTMENTS: To adjust spring tension, add or remove wraps of hose from the spool, one wrap at a time until desired tension is
obtained.
REPAIRS: Extensive repairs should be performed only by an authorized serviceman or factory to avoid damage which may
void your warranty. Remove all spring tension before beginning disassembly process.
MODIFICATION: Hose latching mechanism can be removed for constant tension applications.
D9200 OMP D9300 OMP D9350 OMP
D9275 OMP D9330 OMP
Four 7/16” diameter mounting holes
Operating Instructions
Series D9000 Spring Driven Hose Reels
Medium Pressure Model Numbers:
Reelcraft Industries, Inc. • 2842 E Business Hwy 30, Columbia City, IN 46725
Ph: 800-444-3134 / 260-248-8188 • Fax: [phone]
Customer Service: 855-634-9109 • [email protected] • www.reelcraft.com
A26 1/4”
B26 1/4”
C13 3/4”
D12 1/8”
E24 1/4”
F22 1/4”
G4 3/4”
H 12”
J7 3/4”
K 4”
L 7/16”
A
B
E
C
D
FG
JH
L
K
Dimensions
Form# 497-285 Rev: 11/2016

Series D9000 Spring Driven Hose Reels
Page 2 www.reelcraft.com
Item
#Part # # Req Description Item #Part # # Req Description Item #Part # # Req Description
1 S2-41 4 1/4-20 x 1/2” hex screw 14 S270054 1 1” Inlet tube 33 262436-5.468 2Guide roller
2 270009 2 Side frame 15 270029 1 Hose outlet support 34 262436-2.968 2Guide roller
3 S281-6 12 3/8-16 hex flange nut 16 S32-136 1 #10 x 3/8” self tap screw 36 S270014 4Guide roller post
4 S270058 2 Pillow block 18 270029 1 90° ell 37 270011 1 Hose guide roller plate
5 270012 1 End frame support 19 S270001 1 Latch ratchet hub 38 S2-51 4 5/16-18 x 1/2” hex screw
6 S44-2 8 3/8-16 x 5/8” mach. screw 20 S2-42 4 1/4-20 x 5/8” hex screw 39 270045 1 Guide roller plate SW
7 S44-8 4 3/8-16 x 1 3/4” screw 23 S280-8 1 1/2-20 hex flange nut 40 270043 1 SW support bracket
8 602314 1 Support shaft 24 S82-15 1 10-32 x 3/8” nyloc nut 41 270042 1 SW support bracket
9 S140-31 6 Snap ring 25 S600018 1 Latch pawl assembly 42 270044 1 Guide roller plate TW
10 S270105 1 Spring & case assembly 26 S260067 1 Latch spring 43 260143 1 Riser, roller plate LH
11 S270002 1 Spring arbor 28 S393-2 1 10-32 shoulder screw 44 260142 1 Riser, roller plate RH
12 270107 1 Sheave assembly 31 S270016 2 Guide roller pin - long 45 S328-29 4 5/16-18 x 1/2” screw
13 S281-4 8 1/4-20 hex flange nut 32 S270015 2 Guide roller pin - short
Item
#Description # Req D9200 OMP D9275 OMP D9300 OMP D9330 OMP D9350 OMP
17 Bushing 1 S174-112 S174-112 300055 300055 300055
21 Swivel assembly 1 S602033 S602033 S602026 S602026 S602026
22 Coupling reducer 1 S290-5 S290-5 S290-6 S290-6 S290-6
29 Hose assembly 1 None S24-260043 None S26-260043 S27-260043
30 Bumper stop assembly 1 None 2-HR1005 None 3-HR1005 3-HR1005
1
2
3
4
5
6
7
8
9
10
38 37 6
11 12 45 13 14 15 16 17 18 919 20 721
36 34 33 32 31
30
29
28
26
25
2
24
23
4
22 6
39
40
41
3
42
43
6
3
44