Regalo 1164 W User manual

www.regalo-baby.com
Regalo International, LLC.
3200 Corporate Center Drive, Suite 100 / Burnsville, MN 55306, USA
866.272.5274 (U.S. only) or 952.435.1080
Made in China
Easy Step
Safety Gate
OWNER’S MANUAL MODELS: 1160,1164 W/B/P, 1165
• READ ALL INSTRUCTIONS BEFORE ASSEMBLY AND USE OF GATE.
• KEEP INSTRUCTIONS FOR FUTURE USE.

English2
Before Using Product
Read and follow all instructions carefully to ensure that your gate and extensions are
properly installed. Improper installation could result in the gate becoming unstable or
dislodged from the doorway. Always make sure the extension is securely attached
to the gate before using. The safety of your child is your responsibility. Please keep
these instructions for your reference.
IMPORTANT
• If using this gate at the top of stairs, the four wall cups MUST be used.
If not used, the gate may become dislodged from the opening.
• Never use more than two extensions per side of gate.
• If hardware mounting to a surface other than drywall or wood,
please consult with a professional about installation.
WARNING
• Intended for young children aged 6 months through 24 months
• To prevent serious injury or death, securely install gate or enclosure
and use according to manufacturer’s instructions.
• Never use with a child able to climb over or dislodge the
gate or enclosure.
• Never leave child unattended.
• Use only with the locking/latching mechanism securely engaged.
• Check the gate regularly to see if all the hardware and
mountings are tightened.

English 3
PLEASE CHECK TO MAKE SUREYOU HAVE THE FOLLOWING PARTS:
A Gate Frame (1)
B Wall Cups (4)
C Screws (4) (requires a Phillips/cross-head screwdriver)
D Threaded Spindle Rods (4)
Before Assembly
A
D
C
B

English4
MODEL NO. MAX SIZE
1160
1164 W/B/P
1165
29 – 39 inches
29 – 52 inches
29 – 44 inches
Extensions List
NOTE
NOTE: When installing any gate at its maximum width, use wall cups to
ensure stability and safety.
4" 6" 8" 12"

English 5
STEP 1
Locate the (4) threaded
spindle rods. Rotate the
adjustment wheels along
the threading, eliminating the
gap between the adjustment
wheel and the rubber foot.
Assembling and Installing Your Gate
STEP 2
Insert the (4) threaded
spindle rods into the holes
at each of the four corners
of the gate.
NOTE: You will notice a slight gap between the gate door latch and the
frame. This is not a defect. Your gate is a pressure mounted gate and this
gap will disappear once you tighten your gate in its opening.
RUBBER FOOT
ADJUSTMENT WHEEL

English6
NOTE: It may be necessary to hold the threaded spindle rods or rubber feet
while rotating the adjustment wheels to ensure the entire unit does not rotate.
STEP 3
Position the gate so that it is level and centered within your doorway or
opening. Rotate the adjustment wheels on the threaded spindle rods in the
opposite direction as in STEP 1, expanding the gap between the rubber foot
and the adjustment wheel. Expand each of the (4) threaded spindle rods
until they make contact with the doorway or opening. Do not fully tighten the
threaded spindle rods yet.

English 7
STEP 4
When you are satisfied with the general placement of your gate, fully
tighten the threaded spindle rods attached to the lower corners of the gate
by further rotating the adjustment wheels.
Continue by tightening the upper threaded spindle rods. As you tighten
the upper threaded spindle rods, you will notice the gap between the door
frame and the easy open latch begin to narrow.
In order for the gate to function properly, stop tightening the upper
threaded spindle rods just before the inner wall of the locking latch and
the gate frame touch.
NOTE: There should be equal spacing among each of the (4) threaded
spindle rods. Make the appropriate adjustment to ensure you have installed
your gate safely.
LOCKING LATCH
GATE FRAME

English8
Positioning and Attaching the Wall Cups
Your gate is a pressure mounted gate. Therefore, it is not necessary to use the
screw attached wall cups in your door opening if you choose not to. However, if
you are using the gate at the top of the stairs you must use the wall cups.
Using the wall cups will affix your gate more firmly in the doorway or opening.
STEP 1
After you have mounted your gate, and you are satisfied with its positioning,
draw a circle on the surface of your doorway or opening around the perimeter
of the (4) rubber feet.
STEP 2
Next, completely remove the gate from the opening by loosening each of the
(4) threaded spindle rods to depressurize the gate.

English 9
STEP 3
With the gate fully removed, you can now use the circles you marked during
STEP 1 as guides for screwing in your (4) wall cups.
Center each of the wall cups within the guide circles and use the provided
self-tapping screws to fasten them in place via the hole through the center of
each wall cup.
STEP 4
Reinstall your gate in the doorway or opening according to the instructions,
using the newly installed wall cups as anchoring points for the (4) threaded
spindle rods.

English10
Operating the Door Latch
STEP 1
Pull the spring lock away from the easy open latch while simultaneously lifting
the lock lever upwards. This will release the locking latch from the gate frame
and allow the door to push or pull open.
STEP 2
To lock the door shut, close the door completely, then push down on the lock
lever to re-engage the spring lock.
NOTE: If your easy open latch is not properly engaging with the receiving
component, ensure that your gate is level, mounted properly, and that you
have not over-tightened the threaded spindle rods.
LOCK LEVER
SPRING LOCK

English 11
Adding a Gate Extension
STEP 1
Choose the side of the gate to be extended and remove the top and bottom
threaded spindle rods.
STEP 2
Assemble the gate and extension as illustrated. Reposition the gate and fit in
accordance with the gate fitting instructions.
NOTE: It is preferable to install any extensions on the hinge side of the gate.
If you have an application that requires additional extensions, please
contact the manufacturer.

English12
REMOVINGYOUR GATE FROM THE WALL
To remove your gate from the wall, rotate the adjustment wheels on each of the
(4) threaded spindle rods to depressurize the gate from its doorway or opening.
Then, gently pull or push the gate free from its doorway or opening.
CARE AND MAINTENANCE
Periodically check the gate for signs of damage, wear, or missing components.
Do not use if any part is missing, worn or damaged. Check the gate regularly to
ensure all the hardware and mountings are tightened. Do not use abrasive
cleaners or bleach. Clean by sponging with warm water and a mild detergent.
90 DAYS LIMITED WARRANTY
If, during the first 90 days after consumer purchase of the item, under reasonable
and non-commercial use and conditions of maintenance, it fails while owned by
the original purchaser because of the quality of materials or workmanship of finish
and assembly, Regalo International, LLC, will replace or repair it at Regalo’s option.
PROOF OF PURCHASE REQUIRED.

English 13
Replacement Parts
A Easy Open Latch
Gray = #14037
Black = #11037
White = #13037
B Top P l ug I n se r t
Gray = #14020
Black = #11020
C Threaded Spindle Rods
w/Adjustment Wheel
Gray = #14016
Black = #11016
D 1" Wall Mount Screws
#10001
E Wall Cups
Gray = #14015
Black = #11015
F Bottom Plug Insert
Gray = #14019
Black = #11019
A
F
B C D E

French14
www.regalo-baby.com
Regalo International, LLC.
3200 Corporate Center Drive, Suite 100 / Burnsville, MN 55306, É.-U.
866.272.5274 (aux États-Unis seulement) ou 952.435.1080
Fabriqué en Chine
Barrière de sécurité
à ouverture facile
GUIDE D’UTILISATION MODÈLES:1160,1164 W/B/P, 1165
• LIRE TOUTES LES INSTRUCTIONS AVANT D’ASSEMBLER ET
D’UTILISER LA BARRIÈRE.
• CONSERVER CES INSTRUCTIONS POUR UNE UTILISATION
ULTÉRIEURE.

French 15
Avant d’utiliser le produit
Lire et suivre attentivement les instructions pour assurer une installation conforme
de la barrière et des rallonges. Une mauvaise installation risque d’aboutir à une
barrière branlante, ou qui se détache de l’ouverture. Avant utilisation, toujours
s’assurer que la rallonge est fixée solidement à la barrière. Vous êtes responsable
de la sécurité de votre enfant. Conserver ces instructions pour consultation.
IMPORTANT
• Si l’on monte cette barrière en haut d’un escalier, les quatre coupelles murales
DOIVENT être utilisées. Sinon, la barrière risque de se détacher.
• Ne jamais utiliser plus de deux rallonges par côté de barrière.
• Si la surface de fixation n’est pas une cloison sèche ou du bois, consulter un
spécialiste au sujet de l’installation.
AVERTISSEMENT
• Conçue pour les jeunes enfants de 6 à 24 mois.
• Pour prévenir des blessures graves voire mortelles, assembler
solidement la barrière ou le parc; leur utilisation doit être conforme
aux directives du fabricant.
• Ne jamais utiliser si l’enfant est capable de grimper par-dessus ou de
déloger la barrière ou le parc.
• Ne jamais laisser l’enfant sans surveillance.
• Utiliser uniquement lorsque le mécanisme de verrouillage est
solidement engagé.
• Vérifier régulièrement le serrage des pièces de montage et de
fixation.

French16
VEUILLEZ VÉRIFIER QUE VOUS DISPOSEZ DES ARTICLES SUIVANTS:
A Cadre de barrière (1)
B Coupelles murales (4)
C Vis (4) (tournevis cruciforme/Phillips requis)
D Tiges filetées (4)
Avant l’assemblage
A
D
C
B

French 17
NODE MODÈLE DIMENSIONS MAXIMUM
1160
1164 W/B/P
1165
74 cm à 99 cm
74 cm à 132 cm
74 cm à 112 cm
Liste des rallonges
REMARQUE
REMARQUE : Si l’on déploie la barrière à sa largeur maximale, utiliser les
coupelles murales pour assurer la stabilité et la sécurité.
10 cm 15 cm 20 cm 30 cm

French18
ÉTAPE 1
Repérez les quatre (4)
tiges filetées. Tournez les
molettes le long du filetage
de manière à supprimer
l’écart entre la molette et le
pied caoutchouté.
Assemblage et installation de la barrière
ÉTAPE2
Insérez les quatre (4) tiges
filetées dans les trous
situés aux quatre coins de
la barrière.
REMARQUE : Vous remarquerez un léger espace entre le loquet de porte et le
cadre de la barrière. Cela n’est pas un défaut. Le montage de votre barrière
s’effectue en effet par pression : le serrage de la barrière dans l’ouverture
comblera cet espace.
PIED CAOUTCHOUTÉ
MOLETTE

French 19
REMARQUE : Vous devrez peut-être tenir les tiges filetées ou le pied
caoutchouté pendant que vous tournez les molettes afin d’empêcher
l’ensemble de pivoter.
ÉTAPE3
Placez la barrière de niveau et centrée dans l’embrasure de la porte ou dans
l’ouverture. Tournez les molettes des tiges filetées dans la direction opposée
de L’ÉTAPE1, en augmentant la distance entre le pied caoutchouté et la
molette. Étendez les quatre (4) tiges filetées jusqu’à ce que le pied touche
l’embrasure de la porte ou l’ouverture. Ne serrez pas complètement les tiges
filetées à ce stade.

French20
ÉTAPE4
Une fois satisfait de la position globale de votre barrière, serrez fermement les
tiges filetées fixées aux coins inférieurs de la barrière en continuant de tourner
les molettes.
Serrez ensuite fermement les tiges filetées supérieures. À mesure que vous
serrez les tiges filetées supérieures, vous constaterez que l’espace se resserre
entre le cadre de la porte et le loquet à ouverture facile.
Pour que la barrière fonctionne bien, arrêtez de serrer les molettes des tiges
filetées supérieures juste avant que le cadre de la barrière touche le côté du
loquet.
REMARQUE : Les quatre (4) tiges filetées devraient être espacées
également. Faites le réglage approprié pour que la barrière installée soit
sécuritaire.
LOQUET
CADRE DE BARRIÈRE