Regalo Home Accents Superwide User manual

www.regalo-baby.com
Regalo International, LLC.
3200 Corporate Center Drive, Suite 100 / Burnsville, MN 55306, USA
866.272.5274 (U.S. only) or 952.435.1080
Made in China
Home Accents Superwide
Safety Gate
OWNER’S MANUAL MODEL: 1176
• READ ALL INSTRUCTIONS BEFORE ASSEMBLY AND USE OF GATE.
• KEEP INSTRUCTIONS FOR FUTURE USE.

English2
Before Using Product
Read and follow all instructions carefully to ensure that your gate is properly
installed. Improper installation could result in the gate becoming unstable or
dislodged from the doorway. The safety of your child is your responsibility.
Please keep these instructions for your reference.
IMPORTANT
• Mounting hardware must be mounted into the wall.
• Base locks are to be used at all times, on both sides of the gate.

English 3
WARNING
• Install according to manufacturer's instructions.
• Children have died or been seriously injured when
gates are not securely installed. ALWAYS install
and use gate as directed using all required parts.
• STOP using when a child can climb over or
dislodge the gate.
• Use only with the locking/latching mechanism
securely engaged.
•NEVER use to keep child away from pool.
•MODEL NO. 1176: Intended for use with children
from 6 months through 24 months.
• This product will not necessarily prevent all
accidents. Never leave child unattended.
•Always ensure the gate is resting against the floor
before beginning installation.
• Check the gate regularly to see if all the hardware
and mountings are tightened.
• Do not use if any components are missing or
damaged.
• Adult supervision is required at all times.
• Adult assembly required.
• To prevent falls, never use at top of stairs.

English4
MODEL NO. 1176
Manufacturer recommendations:
• For children ages 6 months to 24 months
• When mounting:
•The minimum opening allowed is 56"
• The maximum opening allowed is 74 1/2". Please note if your opening is
larger than 74 1/2" you can purchase the optional Home Accents 2 Panel
Extension Kit, model number 0076.

G
English 5
Before Assembly
F
ABC
DE
H
PLEASE CHECK TO MAKE SURE YOU HAVE THE FOLLOWING PARTS:
A Main Gate Assembly(2) HCap Hinge Cover (1)
B Pan Head Screw (4)
C Wood screw (8)
D Allen Wrench (1)
E Upper Door Hinge Pin (1)
F Door Frame U-bracket (1)
G Door Frame Assembly (1)

English6
Gate Assembly
STEP 1
Start with the main gate assemblies. Loosen the hinge knob in the clockwise
direction. Doing this will let main gate assemblies unfold.
STEP 2
Slide the two gate assemblies together. Place the door frame u-bracket over
the lower frame lining up the four (4) holes. Using the allen wrench tighten
down the four (4) pan head screws. Rotate the allen wrench in the clockwise
direction to tighten the screws.

English 7
Gate Assembly
STEP 3
Set the door frame assembly into the gate. Set the pin of the door frame
assembly into the receiver hole on the main frame assembly.
STEP 4
Place the upper door hinge pin through the hole in the main frame assembly
and into the door frame assembly. Note: Once the upper door hinge pin is
installed it will not be removed easily.

English8
Mounting of the Gate
STEP 1
Determine what side you wish to have the hinge of the door on. Place the wall
mounts on that end of the gate against the wall. Using the wood screws, screw
into the wall. Turning the a screwdriver in the clockwise direction will tighten
the screws. Repeat on both ends of the gate. Note: If your application does not
require both extension gates, refer to removing extension gate.
STEP 2
Tighten all the gate hinges by twising the hinge knob counter clockwise
direction..

English 9
Removing Extension Gate
STEP 1
If the standard gate is too long for your opening you must remove either the
right or left extension gate. Loosen the hinge knob in the clockwise direction.
Slide the hinge knob down and pull out the tube hinge. Do the same with the
tube hinge on the end with the wall mounts.
STEP 2
Remove the hinge cover cap. Hinge cover cap is on the bottom of the hinge
with the wall mounts. Remove the toothed hinge cap from the top.

English10
Removing Extension Gate
STEP 3
Place the tube hinge, wall mounts, hinge knob, and cap hinge cover into the
lower door frame. Place the toothed hinge cover on the top of the gate. Slide
the hinge knob up into the toothed hinge cover and twist counter-clockwise
to tighten. Once the hinge knob is tight lower the cap hinge cover all the way
down.

English 11
Gate Operation
STEP 1
To open the gate, start with rotating the base lock in the upward direction.
Do this on both sides of the door. Note: You can rotate the base lock in either
direction.
STEP 2
Press the release button down on the handle. Slide the handle towards the
hinge. Note: Handle is spring loaded and will return to its "locked" position on
its own. When closing the gate you must do the same operation.

English12
CARE AND MAINTENANCE
Periodically check the gate for signs of damage, wear, or missing components.
Do not use if any part is missing, worn or damaged. Check the gate regularly to
ensure all the hardware and mountings are tightened. Do not use abrasive
cleaners or bleach. Clean by sponging with warm water and a mild detergent.
90 DAYS LIMITED WARRANTY
If, during the first 90 days after consumer purchase of the item, under reasonable
and non-commercial use and conditions of maintenance, it fails while owned by
the original purchaser because of the quality of materials or workmanship of finish
and assembly, Regalo International, LLC, will replace or repair it at Regalo’s option.
PROOF OF PURCHASE REQUIRED.

English 13
Replacement Parts
B
A
A Slide Handle, Kit,
Narrow
#100430-002
B Endcap Plug, Disc
Hinge, Doorframe, Male
#300306-002
C Pin, Hinge, Spring
#100267-001
D Screw Wood, GB 3.5MM
x 25MM
E Screw Wood, GB 3.5MM
x 25MM
B
C
E
F Endcap, Disc Hinge,
Bottom, Male
#300322-002
G Endcap, Disc Hinge,
Bottom, Male
#300322-002
F
F
G
H Knob Hinge
#300778-002
I Endcap, Disc Hinge,
Toothed, Doorframe,
Male
#300779-002
H
I
J Endcap, Disc Hinge,
Toothed, Doorframe,
Female
#300781-002
J
K Disc, Hinge Toothed
#300783-002
K
L U-bracket, Junction,
Doorframe
#301272-001
L
M Tube, Steel, Ø10mm x
683mm
#301273-001
M

English14
Replacement Parts
N
N Cap, Hinge Cover,
Female
#301312-002
O Hinge Cover, Endcap
Plug, 13mm/13mm
#301354-002
O