Regalo WideSpan Extra Wide 1158 User manual

www.regalo-baby.com
Regalo International, LLC.
3200 Corporate Center Drive, Suite 100 / Burnsville, MN 55306, USA
866.272.5274 (U.S. only) or 952.435.1080
Made in China
WideSpan Extra Wide
Safety Gate
OWNER’S MANUAL MODEL: 1158, 1158CA
• READ ALL INSTRUCTIONS BEFORE ASSEMBLY AND USE OF GATE.
• KEEP INSTRUCTIONS FOR FUTURE USE.

English2
Before Using Product
Read and follow all instructions carefully to ensure that your gate and extensions are
properly installed. Improper installation could result in the gate becoming unstable or
dislodged from the doorway. Always make sure the extension is securely attached
to the gate before using. The safety of your child is your responsibility. Please keep
these instructions for your reference.
IMPORTANT
• Never use more than two extensions per side of gate.
• If hardware mounting to a surface other than drywall or wood,
please consult with a professional about installation.

English 3
WARNING
• Install according to manufacturer's instructions.
• Children have died or been seriously injured
when gates are not securely installed. ALWAYS
install and use gate as directed using all required
parts.
• STOP using when child can climb over or
dislodge the gate.
• Use only with the locking/latching mechanism
securely engaged.
•If using this gate at the top of stairs, the four wall
cups MUST be used. If not used, the gate may be
dislodged from the opening.
• NEVER use to keep child away from pool.
• Intended for use with children aged 6 months
through 24 months.
• This product will not necessarily prevent all
accidents. Never leave child unattended.
•Always ensure the gate is resting against the floor
before beginning installation.
• Check the gate regularly to see if all the hardware
and mountings are tightened.
• Do not use if any components are missing or
damaged.

A
English4
PLEASE CHECKTO MAKE SUREYOU HAVE THE FOLLOWING PARTS:
A Gate Frame (1)
B Wall Cups (4)
C Screws (4) (requires a Phillips/cross-head screwdriver)
D Threaded Spindle Rods (4)
Before Assembly
D
C
B

English 5
MODEL NO. MAX SIZE
6" 8" 12"
1158/1158CA 29 – 58 inches
Extensions List
NOTE
NOTE: When installing any gate at its maximum width, use wall cups to
ensure stability and safety.
WARNING: The gap between the gate and wall should not exceed
2.5 inches.

English6
STEP 1
Locate the (4) threaded
spindle rods. Rotate the
adjustment wheels along
the threading, eliminating the
gap between the adjustment
wheel and the rubber foot.
Assembling and InstallingYour Gate
STEP 2
Insert the (4) threaded
spindle rods into the holes
at each of the four corners
of the gate.
NOTE: You will notice a slight gap between the gate door latch and the
frame. This is not a defect. Your gate is a pressure mounted gate and this
gap will disappear once you tighten your gate in its opening.
RUBBER FOOT
ADJUSTMENT WHEEL

English 7
NOTE: It may be necessary to hold the threaded spindle rods or rubber feet
while rotating the adjustment wheels to ensure the entire unit does not rotate.
STEP 3
Position the gate so that it is level and centered within your doorway or
opening. Rotate the adjustment wheels on the threaded spindle rods in the
opposite direction as in STEP 1, expanding the gap between the rubber foot
and the adjustment wheel. Expand each of the (4) threaded spindle rods
until they make contact with the doorway or opening. Do not fully tighten the
threaded spindle rods yet.

English8
STEP 4
When you are satisfied with the general placement of your gate, fully
tighten the threaded spindle rods attached to the lower corners of the gate
by further rotating the adjustment wheels.
Continue by tightening the upper threaded spindle rods. As you tighten
the upper threaded spindle rods, you will notice the gap between the door
frame and the easy open latch begin to narrow.
In order for the gate to function properly, stop tightening the upper
threaded spindle rods just before the inner wall of the locking latch and
the gate frame touch.
NOTE: There should be equal spacing among each of the (4) threaded
spindle rods. Make the appropriate adjustment to ensure you have installed
your gate safely.
LOCKING LATCH
GATE FRAME

English 9
Positioning and Attaching the Wall Cups
Your gate is a pressure mounted gate. Therefore, it is not necessary to use the
screw attached wall cups in your door opening if you choose not to. However, if
you are using the gate at the top of the stairs you must use the wall cups.
Using the wall cups will affix your gate more firmly in the doorway or opening.
STEP 1
After you have mounted your gate, and you are satisfied with its positioning,
draw a circle on the surface of your doorway or opening around the perimeter
of the (4) rubber feet.
STEP 2
Next, completely remove the gate from the opening by loosening each of the
(4) threaded spindle rods to depressurize the gate.

English10
STEP 3
With the gate fully removed, you can now use the circles you marked during
STEP 1 as guides for screwing in your (4) wall cups.
Center each of the wall cups within the guide circles and use the provided
self-tapping screws to fasten them in place via the hole through the center of
each wall cup.
STEP 4
Reinstall your gate in the doorway or opening according to the instructions,
using the newly installed wall cups as anchoring points for the (4) threaded
spindle rods.

English 11
Operating the Door Latch
STEP 1
Pull the spring lock away from the easy open latch while simultaneously lifting
the lock lever upwards. This will release the locking latch from the gate frame
and allow the door to push or pull open.
STEP 2
To lock the door shut, close the door completely, then push down on the lock
lever to re-engage the spring lock.
NOTE: If your easy open latch is not properly engaging with the receiving
component, ensure that your gate is level, mounted properly, and that you
have not over-tightened the threaded spindle rods.
LOCK LEVER
SPRING LOCK

English12
Adding a Gate Extension
STEP 1
Choose the side of the gate to be extended and remove the top and bottom
threaded spindle rods.
STEP 2
Assemble the gate and extension as illustrated. Reposition the gate and fit in
accordance with the gate fitting instructions.
NOTE: It is preferable to install any extensions on the hinge side of the gate.
If you have an application that requires additional extensions, please
contact the manufacturer.

English 13
REMOVING YOUR GATE FROM THE WALL
To remove your gate from the wall, rotate the adjustment wheels on each of the
(4) threaded spindle rods to depressurize the gate from its doorway or opening.
Then, gently pull or push the gate free from its doorway or opening.
CARE AND MAINTENANCE
Periodically check the gate for signs of damage, wear, or missing components.
Do not use if any part is missing, worn or damaged. Check the gate regularly to
ensure all the hardware and mountings are tightened. Do not use abrasive
cleaners or bleach. Clean by sponging with warm water and a mild detergent.
90 DAYS LIMITED WARRANTY
If, during the first 90 days after consumer purchase of the item, under reasonable
and non-commercial use and conditions of maintenance, it fails while owned by
the original purchaser because of the quality of materials or workmanship of finish
and assembly, Regalo International, LLC, will replace or repair it at Regalo’s option.
PROOF OF PURCHASE REQUIRED.

English14
Replacement Parts
A
F
B C D E
A Easy Open Latch
White = #13037
B Top Plug Insert
Gray = #14020
C
C Threaded Spindle Rods
w/Adjustment Wheel
Gray = #14016
D 1" Wall Mount Screws
#10001
E Wall Cups
Gray = #14015
F Bottom Plug Insert
Gray = #14019

French 15
www.regalo-baby.com
Regalo International, LLC.
3200 Corporate Center Drive, Suite 100 / Burnsville, MN 55306, É.-U.
866.272.5274 (aux États-Unis seulement) ou 952.435.1080
Fabriqué en Chine
Barrière de sécurité
extra large à grande portée
GUIDE D’UTILISATION MODÈLE : 1158, 1158CA
• LIRE TOUTES LES INSTRUCTIONS AVANT D’ASSEMBLER ET
D’UTILISER LA BARRIÈRE.
• CONSERVER CES INSTRUCTIONS POUR UNE UTILISATION
ULTÉRIEURE.

French16
Avant d’utiliser le produit
Lire et suivre attentivement les instructions pour assurer une installation conforme
de la barrière et des rallonges. Une mauvaise installation risque d’aboutir à une
barrière branlante, ou qui se détache de l’ouverture. Avant utilisation, toujours
s’assurer que la rallonge est fixée solidement à la barrière. Vous êtes responsable
de la sécurité de votre enfant. Conserver ces instructions pour consultation.
IMPORTANT
• Ne jamais utiliser plus de deux rallonges par côté de barrière.
• Si la surface de fixation n’est pas une cloison sèche ou du bois, consulter un
spécialiste au sujet de l’installation.

French 17
MISE EN GARDE
• Installer conformément aux instructions du
fabricant.
• Des enfants sont morts ou ont subi de graves
blessures en raison de barrières et de parcs mal
fixés. TOUJOURS installer et utiliser les barrières
et les parcs conformément aux directives en
utilisant toutes les pièces nécessaires.
• CESSER l'utilisation si un enfant est capable de
grimper par-dessus la barrière ou le parc ou de
les déloger.
• N'utiliser l'article que lorsque le mécanisme de
fermeture/verrouillage est solidement enclenché.
•Si l’on monte cette barrière en haut d’un escalier,
les quatre coupelles murales DOIVENT être
utilisées. Sinon, la barrière risque de se détacher.
• Ne JAMAIS utiliser pour tenir les enfants à l'écart
d'une piscine.
• Destiné aux enfants de 6 à 24 mois.
• Cet article ne prévient pas nécessairement tous
les accidents. Ne jamais laisser l’enfant sans
surveillance.
•Toujours s’assurer que la barrière repose sur le
sol avant de commencer l’installation.
• Vérifier régulièrement le serrage des pièces de
montage et de fixation.
• Ne pas utiliser s'il manque des pièces ou elles
sont endommagées.

A
French18
VEUILLEZ VÉRIFIER QUE VOUS DISPOSEZ DES ARTICLES SUIVANTS:
A Cadre de barrière (1)
B Coupelles murales (4)
C Vis (4) (tournevis cruciforme/Phillips requis)
D Tiges filetées (4)
Avant l’assemblage
D
C
B

French 19
NODE MODÈLE DIMENSIONS MAXIMUM
15 cm 20 cm 30 cm
1158/1158CA 74 cm à 147 cm
Liste des rallonges
REMARQUE
REMARQUE : Si l'on déploie la barrière à sa largeur maximale, utiliser les
coupelles murales pour assurer la stabilité et la sécurité.
MISE EN GARDE : La distance entre la barrière et le mur ne doit
pas être supérieure à 6 cm (2,5 po) sur l’un ou l’autre des côtés de la barrière.

French20
ÉTAPE 1
Repérez les quatre (4)
tiges filetées. Tournez les
molettes le long du filetage
de manière à supprimer
l'écart entre la molette et le
pied caoutchouté.
Assemblage et installation de la barrière
ÉTAPE2
Insérez les quatre (4)
tiges filetées dans les
trous situés aux quatre
coins de la barrière.
REMARQUE : Vous remarquerez un léger espace entre le loquet de porte
et le cadre de la barrière. Cela n'est pas un défaut. Le montage de votre
barrière s'effectue en effet par pression : le serrage de la barrière dans
l'ouverture comblera cet espace.
PIED CAOUTCHOUTÉ
MOLETTE