Regalo Home Accents 0310 User manual

www.regalo-baby.com
Regalo International, LLC.
3200 Corporate Center Drive, Suite 100 / Burnsville, MN 55306, USA
866.272.5274 (U.S. only) or 952.435.1080
Made in China
Home Accents
Safety Gate
OWNER’S MANUAL MODELS: 0310, 0320
• READ ALL INSTRUCTIONS BEFORE ASSEMBLY AND USE OF GATE.
• KEEP INSTRUCTIONS FOR FUTURE USE.

English 3
Before Using Product
Read and follow all instructions carefully to ensure that your gate and extensions
are properly installed. Improper installation could result in the gate becoming
unstable or dislodged from the doorway. Always make sure the extension is securely
attached to the gate before using. The safety of your child is your responsibility.
Please keep these instructions for your reference.
IMPORTANT
• Never use more than two extensions per side of gate.
• If hardware mounting to a surface other than drywall or wood,
please consult with a professional about installation.

English4
WARNING
• Install according to manufacturer's instructions.
• Children have died or been seriously injured when
gates are not securely installed. ALWAYS install
and use gate as directed using all required parts.
• STOP using when a child can climb over or
dislodge the gate.
• Use only with the locking/latching mechanism
securely engaged.
• To prevent falls, never use at top of stairs.
• NEVER use to keep child away from pool.
• MODEL 0310: Intended for use with children from
6 months through 24 months.
• MODEL 0320: Intended for use with children from
6 months through 36 months.
• This product will not necessarily prevent all
accidents. Never leave child unattended.
•Always ensure the gate is resting against the floor
before beginning installation.
• Check the gate regularly to see if all the hardware
and mountings are tightened.
• Do not use if any components are missing or
damaged.

English 5
PLEASE CHECK TO MAKE SURE YOU HAVE THE FOLLOWING PARTS:
A Gate Frame (1)
B Wall Cups (4)
C Screws (4) (requires a Phillips/cross-head screwdriver)
D Threaded Spindle Rods (4)
Before Assembly
A
D
C
B

English6
MODEL NO. MAX SIZE
0310
0320
30 – 43.5 inches
30 – 43.5 inches
Extensions List
NOTE
NOTE: When installing any gate at its maximum width, use wall cups to
ensure stability and safety.
4" 6" 8" 12"
WARNING: The gap between the gate and wall should not exceed
more than 2.5 inches.

English 7
STEP 1
Locate the (4) threaded
spindle rods. Rotate the
adjustment wheels along
the threading, eliminating the
gap between the adjustment
wheel and the rubber foot.
NOTE: You will notice a slight gap between the gate door latch and the
frame. This is not a defect. Your gate is a pressure mounted gate and this
gap will disappear once you tighten your gate in its opening.
Assembling and Installing Your Gate
STEP 2
Insert the (4) threaded spindle
rods into the holes at each of
the four corners of the gate.
RUBBER FOOT
ADJUSTMENT WHEEL

English8
NOTE: It may be necessary to hold the threaded spindle rods or rubber feet
while rotating the adjustment wheels to ensure the entire unit does not rotate.
STEP 3
Position the gate so that it is level and centered within your doorway or
opening. Rotate the adjustment wheels on the threaded spindle rods in the
opposite direction as in STEP 1, expanding the gap between the rubber foot
and the adjustment wheel. Expand each of the (4) threaded spindle rods
until they make contact with the doorway or opening. Do not fully tighten the
threaded spindle rods yet.

English 9
STEP 4
When you are satisfied with the general placement of your gate, fully
tighten the threaded spindle rods attached to the lower corners of the gate
by further rotating the adjustment wheels.
Continue by tightening the upper threaded spindle rods. As you tighten the
threaded spindle rods, you will notice the gap between the door frame and the
easy slide latch begin to narrow.
In order for the gate to function properly, stop tightening the upper threaded
spindle rods just before the outer housing of the easy slide latch and the
receiving component touch.
RECEIVING COMPONENT
OUTER HOUSING
NOTE: The gap between the gate and wall should not exceed more than
2.5 inches. Make the appropriate adjustment to ensure you have installed
your gate safely.

English10
Positioning and Attaching the Wall Cups
Using the wall cups will affix your gate more firmly in the doorway or opening.
This is the recommended way to use the gate.
STEP 1
After you have mounted your gate, and you are satisfied with its positioning,
draw a circle on the surface of your doorway or opening around the perimeter
of the (4) rubber feet.
STEP 2
Next, completely remove the gate from the opening by loosening each of the
(4) threaded spindle rods and depressurizing the gate.

English 11
STEP 3
With the gate fully removed, you can now use the circles you marked during
STEP 1 as guides for screwing in your (4) wall cups.
Center each of the wall cups within the guide circles and use the provided
self-tapping screws to fasten them in place via the hole through the center of
each wall cup.
STEP 4
Reinstall your gate in the doorway or opening according to the instructions,
using the newly installed wall cups as anchoring points for the (4) threaded
spindle rods.

English12
Operating the Door Latch
STEP 1
Squeeze one or both of the circular buttons on the easy slide latch while
simultaneously pulling back on one or both of the locking slides. These two
actions combined will disengage the lock and allow the gate to open freely.
STEP 2
Push or pull to open the gate door. To close, simply push or pull the door back
into its original position. The easy slide latch will re-engage automatically and
lock the door into its closed position.
NOTE: If your easy slide latch is not properly engaging with the receiving
component, ensure that your gate is level, mounted properly, and that you
have not over-tightened the threaded spindle rods.
CIRCULAR BUTTON
LOCKING SLIDE

English 13
Adding a Gate Extension
STEP 1
Choose the side of the gate to be extended and remove the top and bottom
threaded spindle rods.
STEP 2
Assemble the gate and extension as illustrated. Reposition the gate and fit in
accordance with the gate fitting instructions.
NOTE: It is preferable to install any extensions on the hinge side of the gate.
If you have an application that requires additional extensions, please
contact the manufacturer.

English14
REMOVING YOUR GATE FROM THE WALL
To remove your gate from the wall, rotate the adjustment wheels on each of the
(4) threaded spindle rods to depressurize the gate from its doorway or opening.
Then, gently pull or push the gate free from its doorway or opening.
CARE AND MAINTENANCE
Periodically check the gate for signs of damage, wear, or missing components.
Do not use if any part is missing, worn or damaged. Check the gate regularly to
ensure all the hardware and mountings are tightened. Do not use abrasive
cleaners or bleach. Clean by sponging with warm water and a mild detergent.
90 DAYS LIMITED WARRANTY
If, during the first 90 days after consumer purchase of the item, under reasonable
and non-commercial use and conditions of maintenance, it fails while owned by
the original purchaser because of the quality of materials or workmanship of finish
and assembly, Regalo International, LLC, will replace or repair it at Regalo’s option.
PROOF OF PURCHASE REQUIRED.

English 15
Replacement Parts
A Threaded Spindle Rods
w/Adjustment Wheel
Black = #11016
B Top Plug Insert
Black = #11020
C
C Easy Slide Latch
Black = #11125
D 1" Wall Mount Screws
#10001
E Bottom Plug Insert
Black = #11019
F Wall Cups
Black = #11015
CBA
D
F
E

www.regalo-baby.com
Regalo International, LLC.
3200 Corporate Center Drive, Suite 100
Burnsville, MN 55306, USA
866.272.5274 (U.S. only) or 952.435.1080
20170524EF