Regalo Super Wide 1340 User manual

Model / Modelo: 1340
2 in 1 Super Wide Safety Gate and Play Yard
2 en 1 Puerta de Seguridad Super Wide y Patio Infantil
www.regalo-baby.com
Regalo International, LLC.
3200 Corporate Center Drive, Suite 100 / Burnsville, MN 55306, USA / EE. UU.
866.272.5274 (U.S. only / solo en EE. UU.)or / o 952.435.1080
Made in China / Hecha en China
• LEA TODAS LAS INSTRUCCIONES ANTES DE MONTAR Y USAR LAREJA.
GUÁRDELAS PARA UTILIZARLAS COMO REFERENCIA.
• READ ALL INSTRUCTIONS BEFORE ASSEMBLY AND USE OF GATE.
KEEP INSTRUCTIONS FOR FUTURE USE.
™
™

English
• Mounting hardware must be mounted into the wall.
• Base locks are to be used at all times, on both sides
of the gate.
• For children ages 6 months to 24 months
When mounting:
• The minimum opening allowed is 56"
• The maximum opening allowed is 130".
• Please note if your opening is larger than 130" you can purchase
the optional 2 Panel Extension Kit, model number 0040 W.
Periodically check the gate for signs of damage, wear, or missing
components. Do not use if any part is missing, worn or damaged.
Check the gate regularly to ensure all the hardware and mountings
are tightened. Do not use abrasive cleaners or bleach. Clean by
sponging with warm water and a mild detergent.
MANUFACTURER RECOMMENDATIONS:
IMPORTANT
CARE AND MAINTENANCE
BEFORE USING PRODUCT
Read and follow all instructions carefully to ensure
that your gate and extensions are properly installed.
Improper installation could result in the gate
becoming unstable or dislodged from the doorway.
Always make sure the extension is securely attached
to the gate before using. The safety of your child is
your responsibility. Please keep these instructions for
your reference.
A
B
C
F
G
Main Gate Assembly (2)
Pan Head Screw (4)
Wood screw (8)
Allen Wrench (1)
PLEASE CHECK TO MAKE SURE YOU HAVE THE FOLLOWING PARTS:
Upper Door Hinge Pin (1)
Door Frame U-bracket (1)
Door Frame Assembly (1)
Cap Hinge Cover (1)
Before Assembly
D
E
H

Gate Assembly
STEP 1
Start with the main gate assemblies (A). Loosen
the hinge knob in the clockwise direction. Doing
this will let main gate assemblies unfold.
STEP 2
Slide the two gate assemblies together. Place
the door frame u-bracket (F) over the lower
frame lining over the four (4) holes. Using the
allen wrench (D) tighten down the four (4) pan
head screws (B). Rotate the allen wrench in the
clockwise direction to tighten the screws.
STEP 3
Set the door frame assembly (G) into the gate.
Set the pin of the door into the receiver hole on
the bottom main frame assembly.
STEP 4
Place the upper door hinge pin (E) through the
hole in the main frame assembly and into the
door frame assembly.
STEP 1
Determine what side you wish to have the hinge
of the door on. Place the wall mounts on that end
of the gate against the wall. Using the wood
screws (C), screw into the wall. Turning the a
screwdriver in the clockwise direction will tighten
the screws. Repeat on both ends of the gate.
STEP 2
Tighten all the gate hinges by twising the hinge
knob counter clockwise direction.
NOTE: Once the upper door hinge pin is
installed it will not be removed easily.
Mounting of the Gate
NOTE: If your application does not require both
extension gates, refer to removing extension gate.

Mounting of the Gate
Completely remove
hinge knob
Loosen all other
hinge knob(s)
Removing Extension Gate
STEP 1
If the standard gate is too long for your
opening you must remove either the right or
left extension gate. Loosen the hinge knob in
the clockwise direction. Slide the hinge knob
down and pull out the tube hinge. Do the
same with the tube hinge on the end with the
wall mounts.
STEP 2
Remove the hinge cover cap. Hinge cover
cap (H) is on the bottom of the hinge with
the wall mounts. Remove the toothed hinge
cap from the top.
STEP 1
Twist the hinge knobs in clockwise direction to
loosen.
STEP 2 STEP 3
Connecting The Panels
To Convert Into Play Yard
If the standard gate is too long for your opening you
must remove either the right or left extension gate.
Loosen the hinge knob in the clockwise direction.
Slide the hinge knob down and pull out the tube
hinge. Do the same with the tube hinge on the end
with the wall mounts.
Removing the Wall Mount: Panel 1
If the standard gate is too long for your
opening you must remove either the right or
left extension gate. Loosen the hinge knob in
the clockwise direction. Slide the hinge knob
down and pull out the tube hinge. Do the
same with the tube hinge on the end with the
wall mounts.
Removing the Wall Mount: Panel 2
Loosen the hinge knob in the clockwise
direction to disengage the locking teeth.
Slide the hinge knob and the toothed hinge
cap downward. Pull the tube along with the
hinge knob, toothed hinge cap, and wall
mounts away from the gate to release all
the parts. Remove the hinge cover cap from
the bottom of the 2 in 1 Super Wide™
Safety Gate.
STEP 4

LOCKED
UNLOCKED
STEP 1
To open the gate, start with rotating the base
lock in the upward direction. Do this on both
sides of the door.
STEP 2
Press the release button down on the handle.
Slide the handle back towards the hinge.
Gate Operation
NOTE: Handle is spring loaded and will return to
its "locked" position on its own. When closing the
gate you must do the same operation.
NOTE: You can rotate the base lock in
either direction.
STEP 5
Place the tube with the hinge knob on it into
the hole in the bottom of the extension gate.
Slide the tube into place and screw the hinge
knob in the counter clockwise direction to
tighten. Assembly is now complete.
90 DAYS LIMITED WARRANTY
If, during the first 90 days after consumer purchase of the item,
under reasonable and non-commercial use and conditions of
maintenance, it fails while owned by the original purchaser because
of the quality of materials or workmanship of finish and assembly,
Regalo International, LLC, will replace or repair it at Regalo’s option.
PROOF OF PURCHASE REQUIRED.
Need More Width?
Please note if your opening is larger than 130" you
can purchase the optional 2 Panel Extension Kit,
model number 0040 W.