Regency Sunrise E33S-NG1 Quick start guide



        




        





      




      


918-747b

01/17/12



Tested by:
Installer

Homeowner:
MODELS: E33S-NG1 Natural Gas E33S-LP1 Propane

2Regency® E33S-1 Sunrise Gas Insert


Congratulations! You are the owner of a state-of-the-art Gas Insert by FPI.
The E33 SunriseTM Gas Insert has been designed to provide you with all the warmth and charm of a replace, at
the ick of a switch. The E33S-NG1 and E33S-LP1 have been approved by Warnock Hersey for both safety and
efciency. As it also bears our own mark, it promises to provide you with economy, comfort and security for many
trouble free years to follow. Please take a moment now to acquaint yourself with these instructions and the many
features of your FPI Fireplace.

Regency® E33S-1 Sunrise Gas Insert 33
table of contents

Copy of Safety Decal ....................................................4

MA Code - CO Detector.................................................5

Dimensions ....................................................................6

Important Message .......................................................7
For Your Safety ..............................................................8
Gas Pressure Testing ....................................................8
Specications ................................................................8
Installation Into A Solid Fuel Burning Fireplace Or
Factory Built Fireplace ...................................................8
Before You Start ............................................................8
Installation Checklist .....................................................9
Materials Required ........................................................9
Minimum Fireplace Opening..........................................9
Minimum Clearances To Combustibles .......................10
Combustible Mantel Clearances................................10
Gas Connection .......................................................... 11
Venting......................................................................... 11
Flue Liner nstallation ................................................... 11
Gas Pipe Pressure Testing ..........................................12
SIT Valve Description ..................................................12
Gas Insert Aeration System .........................................12
Conversion from ng to lp .............................................13
Wiring Diagrams ..........................................................17
Optional Remote Control ............................................18
Optional Wall Thermostat ...........................................18
Optional Reective Panel Installation ..........................19
Glass Crystal or Optional Ceramic stones...................22
Glass Door Installation ................................................22
Contemporary Faceplate &..........................................23
Door Frame Installation ...............................................23
Low prole Faceplate Installation ................................25
Optional Hearth Trim Installation .................................27
Final Check..................................................................28
First Fire ......................................................................28

Operating Instructions .................................................28
Lighting Procedure ......................................................28
Shutdown Procedure ...................................................28
Copy Of Lighting Instruction Plate ..............................29
Automatic Convection
Fan Operation..............................................................29
Normal Operating Sounds Of Gas Appliances ............29

Maintenance Instructions.............................................30
General Vent Maintenance ..........................................30
Door Glass ..................................................................30
Valve Tray Replacement ..............................................31
Fan Replacement ........................................................33

Main Assembly ............................................................35
Accessories .................................................................36
Low prole faceplate ...................................................37

Warranty ......................................................................39

4Regency® E33S-1 Sunrise Gas Insert
safetY label
This is a copy of the safety label that
accompanies the E33 SunriseTM Gas
Insert. We have printed a copy of the
contents here for your review. The safety
label is located on a plate inside the
base of the unit visible when the bottom
louver is opened.




D
E
F
A
B
C
Alcove Width E 76" (1930mm)
Alcove Depth F 36" (914mm)
Fan Part No. 320-517/P
Electrical Supply: 115 V, 56 WATTS, 60 Hz
* Alcove side wall must have a
min. of 8” clearance on one side.
NOT FOR USE WITH SOLID FUEL
MADE IN CANADA /FABRIQUE AU CANADA
DO NOT REMOVE THIS LABEL /
NE PAS ENLEVER CETTE ETIQUETTE
Serial No. / No de serie
Duplicate Serial number
This appliance must be installed in accordance with local codes, if any; if none, follow the National Fuel Gas Code, ANSI Z223.1, or Natural Gas and
Propane Installation Code, CSA B149.1.
This appliance must be installed in accordance with the Standard CAN/CSA Z240 MH, Mobile Housing, in Canada, or with the Manufactured Home
Construction and Safety Standard, Title 24 CFR, Part 3280, in the United States, or when such a standard is not applicable,ANSI/NCSBCS A225.1/NFPA
501A, Manufactured Home Installations Standard
This appliance is only for use with the type of gas indicated on the rating plate and may be installed in an aftermarket, permanently located, manufactured
(mobile) home where not prohibited by local codes. See owner's manual for details.
This appliance is not convertible for use with other gases unless a certified kit is used.
WARNING.This fireplace has been converted for use with a gas fireplace insert only and cannot be used for burning wood or solid fuels unless all original
parts have been replaced, and the fireplace re-approved by the authority having jurisdiction.
Installer l'appareil selon les codes ou règlements locaux, ou, en l'absence de tels règlements, selon les codes d'installation ANSI Z223.1, National Fuel
Gas Code ou CSA-B149.1 en vigueur.
Installer l'appareil selon la norme CAN/CSA-Z240, Série MM, Maison mobiles ou CAN/CSA-Z240 VC, Véhicules de camping, ou la norme 24 CFR Part
3280, Manufactured Home Construction and Safety Standard. Si ces normes ne sont pas pertinentes, utilisez la norme ANSI/NCSBCS A225.1/NFPA
501A, Manufactured Home Installations Standard
AVERTISSEMENT : Ce foyer a été converti pour utilisation avec un foyer au gaz encastrable et ne peut être utiliser pour brûler du bois ou d'autres
combustibles solides à moins que toutes les pièces d'origine aient été remplacées et que le foyer ait été approuvé de nouveau par l'autorité compétente.
For use with glass doors certified with the appliance only
This vented gas fireplace heater is not for use with air filters. Ne pas utiliser de filtre à air avec ce foyer au gaz à évacuation.
Cet appareil doit être utilize uniquement avec le type de gaz indiqué sur la plaque signalétique. Cet appareil peut être installé dans une maison
préfabriquée ou mobile (É.-U. seulement) installée à demeure si les règlements locaux le permettent. Voir la notice de l'utilisateur pour plus de
renseignements. Cet appareil ne peut pas être utilisé avec d'autres gaz sauf si une trousse de conversion certifiée est fournie.
Cet appareil n'est pas convertible pour une utilisation avec d'autres gaz, sauf si un kit certifié est utilisé.
Pour utilisation uniquement avec les portes en verre certifiées avec l'appareil
Listed:
Certified for/Certifi e pour:
Tested to:
WN#
CANADA and U.S.A.
CAN/CGA-2.17-M91, ANSI Z21.88-2009 / CSA 2.33-2009
VENTED GAS FIREPLACE HEATER
/
16042
FOYER AU GAZ À ÉVACUATION
é
VENTED GAS FIREPLACE HEATER - NOT FOR USE WITH SOLID FUELS. /
NE PAS UTILISER AVEC DUCOMBUSTIBLE SOLIDE.
FOYER AU
GAZ À ÉVACUATION -
É ÉQUIP A L'UISINE POUR GAZ PROPANE
É ÉQUIP A L'UISINE POUR GAZ NATURAL
FPI Fireplace Products International Ltd.,
Delta BC, CANADA
Pression d'allimentation minimum
Pression la tubulure d' chappement basse
Pression la tubulure d' chappement lev e
Dimensions de l'orifice
D bit Calorifique minimum
D bit Calorifique maximum
à
à
é
é é é
é
é
Pression d'allimentation minimum
Pression la tubulure d' chappement basse
Pression la tubulure d' chappement lev e
Dimensions de l'orifice
D bit Calorifique minimum
D bit Calorifique maximum
à
à
é
é é é
é
é
340
340
Model/Modele:
E33S-NG1
918-748a
Model/Modele:
E33S-LP1
NATURAL GAS FIREPLACE INSERT: MODEL
Factory Equipped For Altitude 0-4500ft. (0-1370m)
Min. Supply Pressure 5“ WC (1.25 kpa)
Low Setting Man. Pressure 1.1" WC (0.27 kpa)
Max. Manifold Pressure 3.8" WC (0.95 kpa)
Orifice Size 42 DMS
Minimum Input 13,500 Btu/h (3.95 kW)
Maximum Input 26,000 Btu/h (7.61 kW)
E33S-NG1
PROPANE GAS FIREPLACE INSERT: MODEL
Factory Equipped For Altitude 0-4500ft. (0-1370m)
Min. Supply Pressure 12" WC (2.99 kpa)
Low Setting Man. Pressure 2.9" WC (0.72 kpa)
Max. Manifold Pressure 11" WC (2.74 kpa)
Orifice Size 54 DMS
Minimum Input 12,000 Btu/h (3.51 kW)
Maximum Input 23,000 Btu/h (6.74 kW)
E33S-LP1
Minimum Clearances to Combustibles
from Insert
Side Walls A* 8" (203mm)
Ceiling B 47" (1194mm)
Min. Mantel Height C 15" (381mm)
Max. Mantel Depth D 3½" (89mm)
For the State of Massachusetts, installation
and repair must be done by a plumber or
gastter licensed in the Commonwealth of
Massachusetts.
For the State of Massachusetts, exible
connectors shall not exceed 36 inches in
length.
For the State of Massachusetts, the appli-
ances individual manual shut-off must be a
t-handle type valve.
The State of Massachusetts requires the
installation of a carbon monoxide alarm in
accordance with NFPA 720 and a CO alarm
with battery back up in the same room where
the gas appliance is installed.

Regency® E33S-1 Sunrise Gas Insert 5
requirements
5.08: Modifications to NFPA-54, Chapter 10
(2) Revise 10.8.3 by adding the following additional requirements:
(a) For all side wall horizontally vented gas fueled equipment installed in every dwelling, building or structure used in whole or in part for
residential purposes, including those owned or operated by the Commonwealth and where the side wall exhaust vent termination is less than
seven (7) feet above finished grade in the area of the venting, including but not limited to decks and porches, the following requirements shall
be satisfied:
1. INSTALLATION OF CARBON MONOXIDE DETECTORS. At the time of installation of the side wall horizontal vented gas fueled
equipment, the installing plumber or gasfitter shall observe that a hard wired carbon monoxide detector with an alarm and battery back-up is
installed on the floor level where the gas equipment is to be installed. In addition, the installing plumber or gasfitter shall observe that a battery
operated or hard wired carbon monoxide detector with an alarm is installed on each additional level of the dwelling, building or structure
served by the side wall horizontal vented gas fueled equipment. It shall be the responsibility of the property owner to secure the services of
qualified licensed professionals for the installation of hard wired carbon monoxide detectors
a. In the event that the side wall horizontally vented gas fueled equipment is installed in a crawl space or an attic, the hard wired carbon
monoxide detector with alarm and battery back-up may be installed on the next adjacent floor level.
b. In the event that the requirements of this subdivision can not be met at the time of completion of installation, the owner shall have a period of
thirty (30) days to comply with the above requirements; provided, however, that during said thirty (30) day period, a battery operated carbon
monoxide detector with an alarm shall be installed.
2. APPROVED CARBON MONOXIDE DETECTORS. Each carbon monoxide detector as required in accordance with the above provisions
shall comply with NFPA 720 and be ANSI/UL 2034 listed and IAS certified.
3. SIGNAGE. A metal or plastic identification plate shall be permanently mounted to the exterior of the building at a minimum height of eight
(8) feet above grade directly in line with the exhaust vent terminal for the horizontally vented gas fueled heating appliance or equipment. The
sign shall read, in print size no less than one-half (1/2) inch in size, "GAS VENT DIRECTLY BELOW. KEEP CLEAR OF ALL
OBSTRUCTIONS".
4. INSPECTION. The state or local gas inspector of the side wall horizontally vented gas fueled equipment shall not approve the installation
unless, upon inspection, the inspector observes carbon monoxide detectors and signage installed in accordance with the provisions of 248 CMR
5.08(2)(a)1 through 4.
(b) EXEMPTIONS: The following equipment is exempt from 248 CMR 5.08(2)(a)1 through 4:
1. The equipment listed in Chapter 10 entitled "Equipment Not Required To Be Vented" in the most current edition of NFPA 54 as adopted by
the Board; and
2. Product Approved side wall horizontally vented gas fueled equipment installed in a room or structure separate from the dwelling, building or
structure used in whole or in part for residential purposes.
(c) MANUFACTURER REQUIREMENTS - GAS EQUIPMENT VENTING SYSTEM PROVIDED. When the manufacturer of Product
Approved side wall horizontally vented gas equipment provides a venting system design or venting system components with the equipment, the
instructions provided by the manufacturer for installation of the equipment and the venting system shall include:
1. Detailed instructions for the installation of the venting system design or the venting system components; and
2. A complete parts list for the venting system design or venting system.
(d) MANUFACTURER REQUIREMENTS - GAS EQUIPMENT VENTING SYSTEM NOT PROVIDED. When the manufacturer of a
Product Approved side wall horizontally vented gas fueled equipment does not provide the parts for venting the flue gases, but identifies
"special venting systems", the following requirements shall be satisfied by the manufacturer:
1. The referenced "special venting system" instructions shall be included with the appliance or equipment installation instructions; and
2. The "special venting systems" shall be Product Approved by the Board, and the instructions for that system shall include a parts list and
detailed installation instructions.
(e) A copy of all installation instructions for all Product Approved side wall horizontally vented gas fueled equipment, all venting instructions,
all parts lists for venting instructions, and/or all venting design instructions shall remain with the appliance or equipment at the completion of
the installation.

