Screen Innovations ZERO EDGE PRO User manual

Zero Edge Pro
Installation Instructions
INSTALLERS: PLEASE LEAVE THIS MANUAL WITH THE OWNER.
400025 Ι v. 1.7 Ι 28 February

APPLY S/N
STICKER HERE
Screen Innovations warrants its products, to the original purchaser only, to be free from defects in
materials and workmanship for a period of one (1) year from the date of purchase by the original
purchaser provided they are properly operated according to Screen Innovations' instructions and are
not damaged due to improper handling or treatment after shipment from the factory.
This warranty does not apply to equipment showing evidence of misuse, abuse, or accidental damage,
or which has been tampered with or repaired by a person other than authorized Screen Innovations
personnel.
Screen Innovations’ sole obligation under this warranty shall be to repair or to replace (at Screen
Innovations’ option) the defective part of the merchandise. Returns for service should be made to
your Screen Innovations' dealer. If it is necessary for the dealer to return the screen or part to Screen
Innovations, transportation expenses to and from Screen Innovations are payable by the purchaser and
Screen Innovations is not responsible for damage in shipment. To protect yourself against damage or
loss in transit, insure the product and prepay all transportation expenses.


mandated by statute or rule of law are limited to the one (1) year warranty period. This warranty gives

is assumed for expenses or damages resulting from interruption in operation of equipment, or for
incidental, direct, or consequential damages of any nature.
In the event that there is a defect in materials or workmanship of a Screen Innovations product, you

Important: this warranty shall not be valid and screen innovations shall not be bound by this warranty if
the product is not operated in accordance with screen innovations' written instructions.
Keep your sales receipt to prove the date of purchase and your original ownership.
Limited 1 year warranty
on Screen Innovations products

SUGGESTED PROJECTOR PLACEMENT.............................................1
DETERMINE FRAME TYPE.........................................................
 ....................................................
 ....................................................
 ..................................................... 
LED LIGHTS ATTACHMENT...................................................
MATERIAL ATTACHMENT SEQUENCE .............................................11
DETERMINE YOUR MATERIAL ....................................................11
 ...............................
 ................................................
 ..........................
PVC – AT MATERIAL – SLATE, UNITY, PURE AT ATTACHMENTS ......................
...........................
SMALL TRIM ATTACHMENT.................................................
MEDIUM TRIM ATTACHMENT ...............................................
LOGO ATTACHMENT ............................................................
 ...............................................................
..............................................................
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
IP CONTROLLED LIGHTING SETUP................................................
TABLE OF CONTENTS
For more technical support questions - Call: 512.832.6939 or email: [email protected]
Hours of Support: 7:30am – 5pm CST | screeninnovations.com
Please visit support.screeninnovations.
com to nd all the updated documents,
drivers and tutorial videos.
Use this QR code to see the video
tutorials for Black Diamond or Short
Throw snap attachment method
Use this QR code to see the
video tutorials for Slate material.

1
11°
11°
SCREEN
Better
Best
Good
36”-42”
(91cm - 106cm)
SUGGESTED PROJECTOR PLACEMENT

wizard/) for the minimum throw distance requirements based on screen material.

2
5

DETERMINE FRAME TYPE
Note: The vertical support bar is for certain models and sizes only.
Split Frame
Standard Frame

3
2
in the corners.
1
STANDARD FRAME ASSEMBLY
Insert the thin corner brackets into the outside channels and the thick corner brackets into the
inside channels of the vertical frames. Then slide into the channels in the horizontal frames.
Thin Bracket
Thick
If using AT or Maestro material, check to make sure the channel nuts are installed in the
inner channel before proceeding.

4
It is a critical step to square the frame. Refer to the illustration below.

A
3
4Measure the diagonals to check if frame is square. If one diagonal is longer, push the
corners at the diagonal. Tighten all set screws once the diagonals are equal or within

Note: If LED lights were ordered, refer to page 9
to for instructions on attaching LED lights to the
screen frame.
STANDARD FRAME ASSEMBLY

5
1
SPLIT FRAME ASSEMBLY
If using AT or Maestro material, ensure the channel nuts are installed in the inner channel
before proceeding.
Insert the thin corner brackets into the outside channels and the thick corner brackets into
the inside channels of the vertical frames. Slide backets into the channels in the horizontal
frames.
Thin
Bracket
Thick

6
2Slide the horizontal frame pieces together and secure with the splice bars. Attach the vertical
support to the frame as shown. Fully tighten splice bars, leaving the vertical support bar loose
but snug.
SPLIT FRAME ASSEMBLY

7
3
in the corners.
SPLIT FRAME ASSEMBLY

8
It is a critical step to square the frame. Refer to the illustration below.

A
4
5Measure the diagonals to check if the frame is square. If one diagonal is longer, push
on the corners at that diagonal. Tighten all set screws once the diagonals are equal or

SPLIT FRAME ASSEMBLY
Note: If LED lights were ordered, refer to the
following page for instructions on attaching LED
lights to the screen frame.

9
3Plug the lights into the controller plugs.
1
2

and set up separately. Scan the OR code to see the instructions for setup.
Connect the lighting harness to the nuts in the frame piece with the screws included.
Feed the wires through the provided hole.
Note: The controller may already be attached from the factory on some models. If so, skip this step.
LED LIGHTS ATTACHMENT

10
5
LED LIGHTS ATTACHMENT
Cut the light strips at the copper pad
where indicated to the correct length
so they just overlap at the middle of
the top frame piece. DO NOT cut the
light strips at any other location.
Scan this QR code to see the video for LED kit troubleshooting.
+12V
B
G
R
+12V
B
G
R
CUT HERE
Press the lights into the channel on the frame. LED foam must be used when rounding the
corners to protect the circuit. Failure to do so will damage the LED strips. The strip should gently
round the corner.
4Note: Use caution in the next steps; do not kink or fold the light strip, which will cause damage
in the circuit. Use the foam strips provided to losely wrap LEDs around the corners.

11

sides of the screen material.
MATERIAL ATTACHMENT SEQUENCE – ALL MATERIALS
DETERMINE YOUR MATERIAL
PVC – AT Material (Slate AT, Pure AT, Unity AT)
Black Backer – Any AT Material
Refer to page 16
Refer to page 16
Black Diamond or Short Throw Material
Non – AT Material (Slate, Pure, Unity)
Maestro – White AT Material
Refer to page 12
Refer to page 13
Refer to page 14
7
7
11 11
5
8
8
6
9
12 12
10
1
3
4
2

12
1
2

or crease the material as it is unrolled.
BLACK DIAMOND & SHORT THROW MATERIAL ONLY

Once all snaps are attached ip screen over and make sure that
the screen material is at and tight everywhere.
Scan this QR code for the
video for this step:
Minute mark 2:49
The corner pieces are there to keep the material square with the frame during the
attachment sequence (refer to attachment sequence image on page 11).

13
(Slate, Pure, Unity)
1
Note: Wear gloves when handling material. Carefully unroll the screen material onto a clean oor. Take
care to not bend or crease the screen material.
Carefully lay the frame onto the screen material. Center the frame over the screen material.
NON-AT MATERIAL ATTACHMENT
2Remove and discard the black retaining bumpers; spread out the posts so they align with the
snaps on the screen material.
Note: Refer to attachment sequence image on page 11.

14
2Carefully lay the frame onto the screen material. Center the frame around the screen material.
1
MAESTRO (WHITE) – AT MATERIAL – ATTACHMENT

if the screen material is bunched up at the rods, work from the middle out, spreading the screen

Note: Wear gloves when handling the material. Carefully unroll the screen material onto a clean oor.
Take care to not bend or crease the screen material.

15
3Remove and discard the black retaining bumpers, then spread out the posts so they align
with the holes in the screen material.
Note: This attachment method is for Maestro material only. Skip to next step for all other AT materials.
MAESTRO (WHITE) – AT MATERIAL – ATTACHMENT
4Make sure the screen material is centered around the frame before proceeding. Refer to the
attachment sequence image on page 11.
Pull one end of the bungee through the hole in the material and place around the post while
holding the other end. Pull the other end over the post. Repeat for all four corners.

16

material. Once all snaps are attached (following the sequence above), ip screen over and make sure
that the screen material is at and taut everywhere.
Scan the QR code to the PVC snap
attachement video.
PVC AT MATERIAL ATTACHMENT
(Slate AT, Pure AT, Unity AT)
BLACK BACKER ATTACHMENT – ANY AT MATERIAL

everywhere.

unusable
nuts is to use the screw.
Acoustically Transparent (AT) materials come with a black backer that must be installed to eliminate
light scatter.
1

17
Attach the black backer to the inside of the frame through the grommets. Secure with thumb
screws.
2
BLACK BACKER ATTACHMENT – ANY AT MATERIAL
Secure black backer material with provided thumb screws.
3