REP AB-5202 User manual

45-0189-V2
AB-5202
6MM
1X INCLUDED
19MM WRENCH
2X INCLUDED

 
25-1512
STEP 2
X1
X1
25-1698
STEP 1
X1
STEP 10
25-1129
X1
STEP 10
20-0188 - NARROW
20-0251 - WIDE
X1
20-0235 - NARROW
STEP 9
20-0250 - WIDE
X1
STEP 1A
25-1469
25-1701
STEP 1B
X1
X1
STEP 5
25-1647
BOX 2
BOX 1
BOX
3
OR BOX
4
RIGHT
LEFT
X1
STEP 7
15-1099
STEP 7
15-1098
X2
STEP 3
15-1598
X1
STEP 3
15-1597
X1
STEP 7
15-1599
X1

 
HARDWARE LIST
M12 WASHER,
BLACK
10-0418
STEP 2
X4
X8
STEPS 2,
10-0419
NYLON INSERT,
M12X1.75, NUT,
BLACK
3, 4, 7, 8
ONE PRE-INSTALLED
M12X1.75, L140
BOLT, BLACK
10-0707
STEP 4
X1
M12X1.75, L105
BOLT, BLACK
10-0443
STEPS 3, 7
X4
STEP 4
10-0706
X1
X2
STEP 2
10-0439
BOLT, BLACK
M12X1.75, L100
X8
STEPS 9, 10
10-0445
BLACK
M10 WASHER,
X8
STEPS 9, 10
10-0449
BOLT, BUTTON HEAD,
M10X1.25, L25,
BLACK
6MM
1X INCLUDED
19MM WRENCH
2X INCLUDED
STEP 5
X2
10-0429
CAP NUT, BLACK
M12X1.75, NUT,
M12X1.75,
CARRIAGE BOLT,
10-0615
X2
STEP 5
BLACK
STEP 8
10-0437
X1
L102
L117

 
SAFETY
ENSURE ALL HARDWARE IS PROPERLY TIGHTENED BEFORE USE.
USE CAUTION WHEN STORING BENCH IN VERTICAL POSITION. IT MAY TIP IF STORED
WITHOUT CARE.
ONLY STORE BENCH WITH THE SEAT PAD AND BACK PAD IN THE 0° POSITION.
DO NOT ADJUST SEAT PAD OR BENCH PAD POSITIONS WHILE IN STORAGE.

 
6
1A
7
1B

 
25-1469
25-1698
10-0450
PRE-INSTALLED
ON 25-1469
8
1A
19MM WRENCH
1X INCLUDED
X1
25-1698
X1
25-1469

 
19MM WRENCH
1X INCLUDED
X1
25-1698 25-1701
X1
8
PRE-INSTALLED
ON 25-1701
25-1701 25-1698
10-0450
1B
1C

 
=

 
10-0439
10-0418
10-0418
10-0419
25-1512
2
19MM WRENCH
2X INCLUDED
X2
10-0439
BOLT, BLACK
M12X1.75, L100
M12 WASHER,
BLACK
10-0418
X4 X2
10-0419
NYLON INSERT,
M12X1.75, NUT,
BLACK
25-1512
X1

 
19MM WRENCH
2X INCLUDED
3
15-1598
X1
X2
10-0419
NYLON INSERT,
M12X1.75, NUT,
BLACK
M12X1.75, L105
BOLT, BLACK
10-0443
X2
15-1597
X1
10-0443
10-0419
15-1597
15-1598

 
4
X1
10-0419
NYLON INSERT,
M12X1.75, NUT,
BLACK
19MM WRENCH
1X INCLUDED
10-0706
X1
L117
M12X1.75, L140
BOLT, BLACK
10-0707
X1
0
4B
4B
4A
10-0707
10-0706
10-0419

 
19MM WRENCH
1X INCLUDED
5
M12X1.75,
CARRIAGE BOLT,
10-0615
X2
BLACK
X2
10-0429
CAP NUT, BLACK
M12X1.75, NUT,
X1
25-1647
10-0615
10-0429
25-1467

 
6
8
X1
10-0419
NYLON INSERT,
M12X1.75, NUT,
BLACK
M12X1.75, L125
BOLT, BLACK
10-0441
X1
10-0419
10-0441
PRE-INSTALLED
PRE-INSTALLED

 
19MM WRENCH
2X INCLUDED
7
X1
15-1099
15-1098
X2
15-1599
X1
X2
10-0419
NYLON INSERT,
M12X1.75, NUT,
BLACK
M12X1.75, L105
BOLT, BLACK
10-0443
X2
10-0443
10-0419
15-1599
15-1098
15-1098
15-1099

 
8
X1
10-0419
NYLON INSERT,
M12X1.75, NUT,
BLACK
19MM WRENCH
1X INCLUDED
10-0437
X1
M12X1.75, L125
BOLT, BLACK
10-0441
X1
8B
8B
8A
10-0441
10-0419
10-0437
20
L102

 
10-0449
10-0445
20-0235 - NARROW
20-0250 - WIDE
9B
9A
DO NOT FULLY
TIGHTEN UNTIL
12
6MM
1X INCLUDED
9
X1
20-0235 - NARROW
20-0250 - WIDE
X2
10-0445
BLACK
M10 WASHER,
X2
10-0449
BOLT, BUTTON HEAD,
M10X1.25, L25,
BLACK

 
10-0445
10-0449
25-1129
20-0188 - NARROW
20-0251 - WIDE
10A
10B 10C
6MM
1X INCLUDED
10
X1
20-0188 - NARROW
20-0251 - WIDE
X6
10-0445
BLACK
M10 WASHER,
X6
10-0449
BOLT, BUTTON HEAD,
M10X1.25, L25,
BLACK
X1
25-1129
0
30

 
11
0

 
6MM
1X INCLUDED
12
FULLY
TIGHTEN

 
TROUBLESHOOTING
IF EITHER PAD HAS TOO MUCH SIDE TO SIDE MOVEMENT
TIGHTEN BOTH CENTRAL HINGE BOLTS UNTIL THERE ARE NO GAPS.
IF SIDE TO SIDE MOVEMENT STILL EXISTS, PROCEED TO
6MM
1X INCLUDED
1TS
2TS
21