REP PR-4000 User manual

PR-4000 Lat Pull-Down Assembly Instructions
Parts Included: Multi-Grip Pullup Bar
2 Poles
Horizontal Pole Brace
2 Weight Horns
2 Cables
Chain
Top Horizontal Brace
Foot Brace
Bottom Horizontal Brace
Name Plate
Hardware Included:
M16x110 Bolt, Washers, Nut
x 4
1. Attach horizontal connecting brace to the
bottom of the back uprights. Also attach
the top brace of the lat pull down to
the top of the rack.
Denver, CO(720) 420-1731
Any issues? Please contact us directly by phone: [phone], email: [e-mail] or
morse code...(.-. . .--. ..-. .. - -. . … …). We are always here for our Customers! - Team REP
M10x25 Bolt, Washers, Nut
x 4
M10x45 Bolt, Washers, Nut
x 3
M12x25 Bolt, Washer
x 4
Handle x 1
M8x20 Bolt, Washer - x 4
2 Pole Supports (Rubber Washer and Bumpers)
6 Pulleys
2 Plates to secure Pulleys
Attachments
x 4
x 8
x 4
(M16x110)
① 㻹㻝㻢㻌㼤㻌㻝㻝㻜㻌㼎㼛㼘㼠㻘㻌㼣㼍㼟㼔㼑㼞㻘㼚㼡㼠
× 4
②
× 2
㻵㼚㼟㼠㼍㼘㼘㼍㼠㼕㼛㼚㻌㻵㼚㼟㼠㼞㼡㼏㼠㼕㼛㼚
PRA-4700
㻼㻾㻭㻙㻠㻣㻜㻜㻚㻝㻥㻜㻟㻞㻝
10 20 30 40 50 60 70 80 90 100 110 120 130 140 150
Millimeters
Inches
1/4 3/4
1/2
1
1/4 3/4
1/2
2
1/4 3/4
1/2
3
1/4 3/4
1/2
4
1/4 3/4
1/2
5
1/4 3/4
1/2
6
䐡
× 3
㻼㼡㼘㼘㼑㼥
④⑤
× 6
⑥
⑦⑧
× 1
× 3
㻹㻝㻜㻌㼤㻌㻥㻜㻌㼎㼛㼘㼠㻘㻌㼣㼍㼟㼔㼑㼞㻘㼚㼡㼠
㼏㼍㼎㼘㼑䞊㻮㻌㻌㻌㻔㻟㻢㻡㻜㼙㼙㻕
㼏㼍㼎㼘㼑䞊㻭㻌㻌㻌㻔㻟㻝㻡㻜㼙㼙㻕
× 4
㻹㻝㻜㻌㼤㻌㻠㻡㻌㼎㼛㼘㼠㻘㻌㼣㼍㼟㼔㼑㼞㻘㼚㼡㼠
M12 x 25 bolt, washer
①
①
②
䐡
䐡
䐡
④
④
× 2
M8 x 20 bolt, washer
⑤
⑤
㻹㻝㻜㻌㼤㻌㻞㻡㻌㼎㼛㼘㼠㻘㻌㼣㼍㼟㼔㼑㼞㻘㼚㼡㼠
⑥
chain
rubber
⑦
⑦
⑦
triangle handle
⑧
䐧㻌㼍㼐㼖㼡㼟㼠㼕㼚㼓㻌㼜㼛㼜㼜㼑㼞㻌㼜㼕㼚
㽢㻝
M10x90 Bolt, Washers,
Stoppers, Nut x 3
Adjusting Pin
(M8x20)
x 2
x 2
2.
Connect bottom pieces of lat
pull down to each other.
x 2
x 2
(M12x25)
x 1
x 1

Denver, CO
Any issues? Please contact us directly by phone: [phone], email: [e-mail] or
morse code...(.-. . .--. ..-. .. - -. . … …). We are always here for our Customers! - Team REP
x4
x 4
(M8x20)
3. Attach bottom of lat attachment to
the horizontal brace of the rack. x 2
x 4
(M12x25)
x 2
4. Set up pole supports and secure them
to the lat attachment.
x3
x 4
(M10x90)
4. Attach the four pulleys that secure
onto the braces of the lat
pulldown system.
x 8
x 6
(M10x45)
x1

Any issues? Please contact us directly by phone: [phone], email: [e-mail] or
morse code...(.-. . .--. ..-. .. - -. . … …). We are always here for our Customers! - Team REP
x 2
5. Feed cables through pulleys and
secure the last two pulleys in their
designated location with plates. One
end of each cable will attach to the
base of the lat pull down to create a
line of tension.
6. Put ball, stopper and cabiner on
the end of each cable so that you can
then attach your attachments.
Secure weight horns.
x 4
(M10x45)
x2
x 4
x 4
(M10x25)
x4