REP PR-4700 User manual

WWW.REPFITNESS.COM 45-0102-A
ASSEMBLY INSTRUCTIONS
PR-4700
STILL NEED HELP WITH ASSEMBLY?
VISIT OUR ASSEMBLY LIBRARY HERE:
HELP.REPFITNESS.COM
NOTE: DO NOT FULLY TIGHTEN
UNTIL FINISHED WITH STEP 10
1X (6MM) ALLEN KEY INCLUDED
NOT INCLUDED
1X 14mm WRENCH
1X 19mm WRENCH
2X 17mm WRENCH
2X 24mm WRENCH

1
WWW.REPFITNESS.COM
If you are missing
any parts, or
otherwise have
any warranty issues,
please file a
warranty claim
on our website:
PARTS LIST
1
10-0023
STEP 2, 6
X8
10-0126
STEP 9
X1
15-0199
STEP 7B
X2
10-0024
X4
STEP 2, 6
STEP 2, 6
X4
10-0057
10-0015
X2
STEP 4
10-0078
X16
STEP 5B, 7B, 8B
10-0020
STEP 5B, 7B, 8B
X10
10-0130
X5
STEP 8C, 10
10-0017
X6
STEP 7B, 8B
10-0021
X6
STEP 7B, 8B
10-0227
X1
STEP 9
10-0225
X2
STEP 5A
X2
10-0314
STEP 4
X3
STEP 7B, 8B
10-0033
10-0228
STEP 5B
X4
X3
STEP 7B, 8B
10-0133

1
WWW.REPFITNESS.COM 2
25-0860
STEP 5A
X1
25-0527
X1
STEP 3
25-0900
X1
STEP 2
25-0529
X1
STEP 9
STEP 8C
X1
25-0958
X1
STEP 6
10-0412
10-0413
STEP 8C
X1
X2
STEP 5B
25-0532
25-0749 / 25-0750
X1
STEP 8A
25-0768 / 25-0767
X1
STEP 7A
25-0530
X1
STEP 10
25-0531
X1
STEP 10
10-0208
10-0208
10-0104
10-0104
X2
STEP 3
25-0536 / 25-0542
PARTS LIST (CONT.)

1
WWW.REPFITNESS.COM 3
STEP
1
IF REAR BASE
STABILIZER
ALREADY
INSTALLED
SKIP TO STEP 2
REAR BASE STABLIZER AND
HARDWARE NOT INCLUDED

1
WWW.REPFITNESS.COM 4
NOTE: CENTER
FRONT BASE ON
REAR BASE
STABILIZER
X2
X4
25-0900
10-0023
10-0024
X2
10-0057
X1
STEP
2
10-0057
10-0023
10-0023
10-0024
25-0900

1
WWW.REPFITNESS.COM 5
STEP
3
25-0527
X1
X2
25-0536 /25-0542
X2
(PRE-INSTALLED)
X2
10-0208
ROD BOLTS
NOTE: GUIDE
COME PRE-
INSTALLED
25-0536 / 25-0542
25-0536 / 25-0542
25-0527
25-0527
10-0104
10-0208
25-0536 / 25-0542
25-0536 / 25-0542
FULLY TIGHTEN BOLTS
10-0104
(PRE-INSTALLED)

1
WWW.REPFITNESS.COM 6
STEP
4
10-0015
10-0314
X2
X2
10-0015
10-0314

1
WWW.REPFITNESS.COM 7
STEP
5A
25-0860
X1
10-0225
X2
25-0860
10-0225
10-0225

1
WWW.REPFITNESS.COM 8
STEP
5B
10-0078
X4 X4
10-0020
X4
X2
25-053210-0228
25-0532
10-0020
10-0078
10-0228

1
WWW.REPFITNESS.COM 9
STEP
6
25-0958
X1
10-0104
X2
X2
X2
X4
10-0023
10-0024
X2
10-0057
25-0962
10-0104
10-0208
10-0024
10-0023
10-0023
10-0057
10-0208
(PRE-INSTALLED) (PRE-INSTALLED)

1
WWW.REPFITNESS.COM 10
STEP
7A
NOTE: THIS CABLE
HAS THREADED BOLT
ATTACHED TO IT.
ROUTE UPPER CABLE
NOTE: CABLE GOES
ABOVE THE BAR
25-0768 / 25-0767
25-0768 / 25-0767
X1

1
WWW.REPFITNESS.COM 11
STEP
7B
ONCE PULLEYS
ARE INSTALLED,
THREAD UPPER
CABLE BOLT
INTO TROLLEY
NOTE: ONLY
THREAD CABLE
HALF WAY
X2
10-0033
10-0017
X4
10-0021
X4
10-0078
X8
10-0020
X4
X2
10-0133
15-0199
X2
NOTE: CABLE
GOES ON TOP OF
BOTH PULLEYS
10-0133
10-0017
10-0033
10-0078
10-0021
10-0021
10-0078
10-0020
10-0033
10-0133 10-0078
10-0020
15-0199
10-0017
10-0078

1
WWW.REPFITNESS.COM 12
STEP
8A
ROUTE LOWER
CABLE
25-0749 / 25-0750
X1

1
WWW.REPFITNESS.COM 13
STEP
8B
INSTALL PULLEYS FOR
LOWER CABLE
TIP: INSTALL
PULLEY FROM
DETAIL VIEW "A"
BEFORE PULLEY
FROM DETAIL
VIEW "B"
10-0020
10-0078
10-0021
10-0033
10-0017
B
10-0078
10-0021
10-0020
10-0133
10-0078
10-0017
A
10-0078
10-0021
X2
10-0078
X4
10-0020
X2
X2
10-0133
10-0017
X2
X1
10-0033
B
A

1
WWW.REPFITNESS.COM 14
STEP
8C
NOTE: ADJUST
CABLE SO
MINIMAL SLACK
IS PRESENT
10-0130
10-0130
ADJUST CABLE TENSION WITH CHAIN
10-0413
X1
10-0130
10-0413
X2

1
WWW.REPFITNESS.COM 15
STEP
9
25-0529
X1
10-0227
X1
10-0126
X1
25-0529
10-0126
10-0227

1
WWW.REPFITNESS.COM 16
STEP
10
10-0130
X3
25-0530
X1
25-0531
X1
10-0412
X1
TIGHTEN ALL HARDWARE
(BOTTOM TO TOP)
ENSURE TOP AND
BOTTOM SQUARENESS
TIP: FOR BEST
OPERATION APPLY
SILICONE SPRAY TO
GUIDE RODS [WHITE
LITHIUM OR GREASE
NOT RECOMMENDED]
REAPPLY AFTER 3-6
MONTHS
NOTE: CHAIN AND
EXTRA CARIBINER
CAN BE USED TO
INCREASE LENGTH
FOR EITHER THE LAT
PULL OR LOW ROW
ATTACHMENT
25-0530
25-0531
10-0130
10-0130