resideo Braukmann MiniPlus FF06 User manual

R32345949-001 Rev.A
Br
au
km
a
nn
MiniPlus FF06/FF06-AAM
Installation instructions Einbauanleitung Instructions d'installation Instrucciones de instalación
Istruzioni di montaggio Installatievoorschrift Beépítési útmutató Руководство по установке
Instrucţiunile de montaj Monteringsvejledningen Instrukcja montażu Instruksjoner for installasjon
Fine Filter Finomszűrő
Feinfilter Фильтр тонкой очистки
Filtre fin Filtru fin
Filtro fino Fint filter
Filtro a maglia fine Filtr dokładny
Fijnfilter Finfilter

GB
2 MU1H-1115GE23 R0220
1 Safety Guidelines
1. Follow the installation instructions.
2. Use the appliance
• according to its intended use
• in good condition
• with due regard to safety and risk of danger.
3. Note that the appliance is exclusively for use in the
applications detailed in these installation instructions
(see 2 Technical Data). Any other use will not be
considered to comply with requirements and would
invalidate the warranty.
4. Please take note that any assembly, commissioning,
servicing and adjustment work may only be carried
out by authorized persons.
5. Immediately rectify any malfunctions which may
influence safety.
2 Technical Data
2.1 FF06
Note: The filter is constructed for drinking water installations. In
case of a process water application the filter has to be
proven individually.
2.2 FF06-AAM
Note: The filter is constructed for drinking water installations. In
case of a process water application the filter has to be
proven individually.
3 Options
For Options visit homecomfort.resideo.com/europe
4 Assembly
4.1 Installation Guidelines
• Install in horizontal pipework with filter bowl
downwards
– This position ensures optimum filter efficiency
• Install shut-off valves
• These filters are armatures which need to be
maintained regularly
• Ensure good access
– Degree of contamination can be easily seen with
clear filter bowl
– Simplifies maintenance and inspection
• The installation location should be protected against
frost
• Related to the EN 806-2 it is recommended to install
the filter immediately after the water meter
• In order to avoid flooding, it is recommended to
arrange a permanent, professionally dimensioned
wastewater connection
4.2 Assembly instructions
We recommend to install an inlet check valve
CAUTION!
Observe the flow direction when mounting the
backflow preventer.
CAUTION!
When connecting the solder sockets, do not solder
the sockets together with the filter. High
temperatures destroy internal parts which are
important to the function!
1. Thoroughly flush pipework
2. Install filter
• Note flow direction
• Install without tension or bending stresses
Media
Medium: Drinking water
Connections/Sizes
Connection sizes: 1/2" - 11/4"
Pressure values
Max. operating pressure: 16 bar
Operating temperatures
Max. operating temperature
medium accord. to EN 1567:
30 °C
Specifications
Installation position: Horizontal with filter bowl
downwards
Media
Medium: Drinking water
Connections/Sizes
Connection sizes: 1/2" - 11/4"
Pressure values
Max. operating pressure: 25 bar
Operating temperatures
Max. operating temperature
medium:
70 °C
Specifications
Installation position: Horizontal with filter bowl
downwards

GB
MU1H-1115GE23 R0220 3
4.3 Drain for rinse water
The rinse water must be piped to the drain in such a
way that no back pressure can occur
1. Discharge into drain connector
2. Discharge into floor drain
*at 4 bar inlet pressure and a rinse duration of 15 seconds
5 Maintenance
In order to comply with EN 806-5, water fixtures must
be inspected and serviced on an annual basis.
As all maintenance work must be carried out by an
installation company, it is recommended that a
servicing contract should be taken out.
In accordance with EN 806-5, the following measures must
be taken:
5.1 Inspection
• Non-compliance can lead to the filter becoming
blocked This results in a drop in pressure and
decreased water flow
• The filter meshes are made of stainless steel. A red
coating as a consequence of rust from the pipelines
has no influence on function or the way the filter works
1. Close shut-off valve on inlet and outlet
2. Release pressure on outlet side (e.g. through water
tap)
If rinse water goes into a container, a suitable
container must first be placed below it.
3. Use the wrench to disassemble the filter bowl.
4. Replace filter mesh and supporting body in filter insert
5. Reassemble in reverse order
5.2 Maintenance
If necessary, the outside surface of the filter
combination can be cleaned.
Use only cold, clear drinking water to clean the
surfaces! Any other cleansers cause damage to the
plastic components!
5.2.1Replace filter mesh
1. Close shut-off valve on inlet
2. Release pressure on outlet side (e.g. through water
tap)
3. Close shut-off valve on outlet
4. Unscrew filter bowl
• Use double ring wrench ZR06F
5. Remove filter cartridge
6. Dismount filter insert
7. Replace filter mesh
8. Clean sieve
9. Clean filter bowl
10. Mount the filter insert
11. Re-insert the filter insert
12. Put O-ring on filter bowl
13. Screw in filter bowl hand-tight (without tools)
14. Slowly open shut-off valve on inlet
15. Slowly open shut-off valve on outlet
6 Disposal
Observe the local requirements regarding correct waste
recycling/disposal!
7 Troubleshooting
8 Spare Parts
For Spare Parts visit homecomfort.resideo.com/europe
9 Accessories
For Accessories visit homecomfort.resideo.com/europe
Filter size Reverse rinsing quantity* C (mm)
1/2" - 1 1/4“ 25 litres 20
Problem Cause Remedy
Too little or no water pressure Shut-off valves upstream or downstream
from filter not fully open
Open the shut-off valves fully
Filter mesh dirty Clean or replace filter
Not fitted in flow direction Fit filter in flow direction

28 MU1H-1115GE23 R0220
4.2 5.1
15s
1. 2.
4.3
&
5.2.1
3.
1.
2.
4.
5.
13.
14. 15.
6.
9.
9.
10.
11.