ReSound ONE 9 User manual

Technical Manual
RS Custom Product Platform
Coyote 6 CIC
GN ReSound A/S
Global Technical Operations
https://gto.gnresound.com
Lautrupbjerg 7
DK-2750 Ballerup
Denmark

Doc 0452940 rev. A
Page 2 of 14
Not subject to issue control when printed
Table of Contents
Form-factor-matrix .......................................................................................................................... 3
Part lists ..........................................................................................................................................4-5
Installing programming module on faceplate............................................................................ 6
Faceplate & programming cable ................................................................................................... 7
Faceplates assemblies C6 CIC........................................................................................................ 8
Microphone assembly...................................................................................................................... 9
Receiver assembly..........................................................................................................................10
Wiring diagram C6 .........................................................................................................................11
Final device......................................................................................................................................12
Test equipment...............................................................................................................................13
Test procedure CIC.........................................................................................................................14

Doc 0452940 rev. A
Page 3 of 14
Not subject to issue control when printed
Form-factor-matrix C6 CIC Resound One
For technical data please refer to Technical Data Sheet / Product Information for each model
Below is a form-factor-matrix of available models for each HI family. This Tech Man contains the necessary repair process for each mentioned model
Cambridge Custom (C6) Battery
10A
Power Single
Mic PB VC Tele coil
Auto
Phone
WL
2.4
WL
E2E
WL
iOS/Android
LP MP HP
ONE
9
RT9CIC-LP x x x Optional N/A N/A N/A N/A N/A N/A
RT9CIC-MP x x x Optional N/A N/A N/A N/A N/A N/A
RT9CIC-HP x x x Optional N/A N/A N/A N/A N/A N/A
ONE
7
RT7CIC-LP x x x Optional N/A N/A N/A N/A N/A N/A
RT7CIC-MP x x x Optional N/A N/A N/A N/A N/A N/A
RT7CIC-HP x x x Optional N/A N/A N/A N/A N/A N/A
ONE
5
RT5CIC-LP x x x Optional N/A N/A N/A N/A N/A N/A
RT5CIC-MP x x x Optional N/A N/A N/A N/A N/A N/A
RT5CIC-HP x x x Optional N/A N/A N/A N/A N/A N/A
ONE
4
RT4CIC-LP x x x Optional N/A N/A N/A N/A N/A N/A
RT4CIC-MP x x x Optional N/A N/A N/A N/A N/A N/A
RT4CIC-HP x x x Optional N/A N/A N/A N/A N/A N/A

Doc 0452940 rev. A
Page 4 of 14
Not subject to issue control when printed
Note: Peters coat must be added after soldering check the vendor website: www.peters.de to purchase locally.
Part No’s for test equipment are to be found on the last pages
Item Part No
SLEEVE,WIRE Uncut (Orange FOR MIC) 11834-001
TYGON TUBING .035X.062 (MIC TUBE) 0198602
TUBING TYGON (REC TUBE) 0198601
WIRE ESW GREEN,7X50U,6MM (PROG) 15130206
WIRE,ESW,AMBER,7X50U,14MM (PROG) 15130114
WIRE,ESW,AMBER,7X50U,18MM (MIC) 15130118
WIRE,ESW,BLUE,7X50U,14MM (PROG) 15130314
WIRE,ESW,GREEN,7X50U,18MM (MIC/BAT -) 15130218
WIRE,ESW,GREEN,7X50U,25MM (REC) 15130225
WIRE,ESW,RED,7X50U,14MM (BAT +) 15130014
WIRE,ESW,RED,7X50U,18MM (MIC) 15130018
WIRE,ESW,RED,7X50U,25MM (REC) 15130025
Item Part No
TUBING,Q-FLEX,.062ID,.095OD (for LP REC) 10049101
TUBING,SILICONE,.100ID X.116OD (for MP-HP REC) 11509-000
TUBING,SILICONE,.120ID X.136OD (For REC.) 10929-000
TUBING,SILICONE,.012”ID.025”OD (for PB) 26100668388
MIC,TO38-30702-G33,PKG 18733300
RECEIVER,44A007 (LP) 16909200
RECEIVER,E50DF007GH (MP) 22349000
RECEIVER,E90DZ009 (HP) 22349100
REC INSULATION TAPE, 9*2MM (For LP Rec) 20872300
REC INSULATION TAPE, 12*3MM (For MP-HP Rec) 20701700
HYB INSULATION TAPE,8*23MM 20588400
HYB INSULATION TAPE,5*16MM 20588500
Part List for C6 CIC

Doc 0452940 rev. A
Page 5 of 14
Not subject to issue control when printed
Program Module (I-Block module) Part No
Light (LHT) 19184900
Medium Brown (MBR) 19184905
Note: See next page (page 6) on properly installing the I-Block Prog
module on raw blank faceplate
Part List Faceplates - Battery Doors - Push Buttons C6 CIC
Push Button Part No
PUSH BUTTON SWITCH,PNK/LHT 20743400
SW,PUSH BUTTON 95,BGE 10000604
SW,PUSH BUTTON 95,DBR 10000606
SW,PUSH BUTTON 95,BN 10000603
PUSH BUTTON SWITCH MBR 20008200
PUSH BUTTON SWITCH,ANT 22395800
Accessories Part No
PUSH BUTTON EXTENDER,BE 6655101
WINDHOOD BGE WHB
WINDHOOD CAR WHCB
WINDHOOD MBN WHMB
WINDHOOD PNK WHP
WINDHOOD ANT 22368400
WINDSCREEN BGE MEDIUM WSB-I
WINDSCREEN BGE SMALL WSB-S
WINDSCREEN CAR MEDIUM WSCB-I
WINDSCREEN CAR SMALL WSCB-S
WINDSCREEN MBN MEDIUM WSMB-I
WINDSCREEN MBN SMALL WSMB-S
WINDSCREEN PNK MEDIUM WSP-I
WINDSCREEN PNK SMALL WSP-S
WINDSCREEN ANT MEDIUM 22368300
WINDSCREEN ANT SMALL 22368200
Battery Doors 10A (nano coated) Type A (Left) Type B (Right)
LIGHT BEIGE 21132910 21132920
BROWN 21132912 21132922
BEIGE 21132914 21132924
MEDIUM BROWN 21132915 21132925
DARK BROWN 21132916 21132926
ANTHRACITE 22483011 22482911
Blank FP 10A UNIVERSAL (Raw) Part No
FP,10A,UNIV,LHT (LIGHT BEIGE) 19184600
FP,10A,UNIV,DRK (BROWN) 19184602
FP,10A,UNIV,BGE (BEIGE) 19184604
FP,10A,UNIV,MBR (MEDIUM BROWN) 19184605
FP,10A,UNIV,DBR (DARK BROWN) 19184606
FP,10A,UNIV,ANT (ANTHRACITE) 19184611

Doc 0452940 rev. A
Page 6 of 14
Not subject to issue control when printed
Raw blank faceplate w/o module Using a tweezer, Pick up module
by contact to avoid damaging the
plastic
Insert module into slot in face-
plate. Contacts point toward
hinge pin
Ensure that the I-Block prog
module is placed evenly (both
ends) on faceplate. Module is not
snapped in all the way
Use a tweezer and press down until it clicks into place. Module is
snapped in and flush to surface of faceplate
“CLICK”
Note: No adhesive necessary to place I-Block module
on faceplate
Installing Programming Module on faceplate

Doc 0452940 rev. A
Page 7 of 14
Not subject to issue control when printed
Faceplates with Prog Module for C6
Programming Module
(I-BLOCK)
Faceplate with Programming
Module
Old CS63 flex
cable strip
New CS63 Flex
cable strip
P/N 19181700
CS53 Adapter Flex 3-PIN
P/N 19533900
Longer
connecting
strip
Stop feature
Stop
guide
feature
Note:
Please make sure to use the new CS63 flex cable with a longer strip connection P/N 19181700 or Adapter Flex,3-PIN CS53 P/N 19533900.
Failure to use the new CS63 flex cable or CS53 Adapter Flex 3-Pin will result to failure of connectivity with the device.

Doc 0452940 rev. A
Page 8 of 14
Not subject to issue control when printed
Faceplates Assemblies C6 CIC
Picture shown is example of the assembly of dierent configurations.
10A FP ASM
C6 CIC

Doc 0452940 rev. A
Page 9 of 14
Not subject to issue control when printed
Solder wires as shown above
NOTE: Peters coat must be added after soldering
(+)
(0)
(-)
(+)
(0)
(-)
(+)
(0)
(-)
Microphone Assembly C6 CIC
Install orange sleeve (2.5mm) to the Mic wire.

Doc 0452940 rev. A
Page 10 of 14
Not subject to issue control when printed
Q-flex tubing
p/n 10049101
Silicone tubing
p/n 10929-000
Solder the wires - Paste Rec Insulation Tape
NOTE: Peters coat must be added after soldering
For LP For - MP-HP
Receiver Assembly C6 CIC
Paste Rec Insulation Tape in the solder joint of REC
Wrap Rec with Tubing,silicone p/n 10929-000.
Place Tubing,silicone uncut 1.3mm around Rec&Wrap
HPMPLP
Place the Q-flex tubing as shown. Bend the wires.
Cut the silicone tubing to 1.3 mm and place it over the wires