Retevis RT22 User manual

RT22
（EN）

WARNINGS
Product safety and RF Exposure for two way radio:
Before using this two way radio, please read
the manual which contains important operating
instructions for safe usage, RF Energy Awa-
reness, control information and operational
instructions for compliance with RF Energy
Exposure limits in applicable national and
international standards, and also read the
operational instructions for safe use.

Function Operation
Standard Accessories
Optional Accessories
More Optional Accessories of Retevis
Get Acqainted
Function Description
Attaching & Removing
Technical Parameters
Warnings
Contents
----------------------------------------- 01
------------------------------------- 02
-------------------------------------- 02
------------------- 03
---------------------------------------------- 04
--------------------------------------- 04
------------------------------------- 05
-------------------------------------- 06
---------------------------------------------------- 07

Antenna
Charger light
Speaker
Microphone
Signal light
PTT key
Monitor
Lock key
Channel
selector plus
Channel
selector reduce
Charger
connector
MIC/Speaker
port
01
USB plug
Charger
connector
Power/Voice volume
Function Operations

Radio body Micro-USB
Belt clip
Charger
Battery
02
Standard Accessories
Optional Accessories

Acoustic tube headset
Speaker microphone
Note:
For more information, please visit our website: www.retevis.com
Throat mic
Programming cable
More Optional Accessories of Retevis
03

● The battery is not charged in a factory. Please charge the battery
before initial use or after long time storage.
● Repeat charging and discharging the battery 2 or 3 times and the
battery would reach its maximum capacity, please replace or
charge the battery when it is in low power.
● The quick consume of the power after normal charge shows
exhaustion of the battery. Please contact your dealer and buy new
approved battery.
● Time-out-timer
The purpose of the Time-out-timer is to prevent any signal person
from using a channel for an extended period of time. If the
transmission continues beyond 10 seconds, the transceiver will
stop transmission and give out alarms. To stop the alarms, please
release the PTT switch and the transceiver will resume the state
of standby.
● Battery Saving
The radio would reduce its power consumption. If there is no
signal or operation over 10 seconds, the battery saving function
would be on automatically. When signal is received or with
operation, the radio would switch to normal mode.
● Low Battery Warning
When the voltage fall down to lowest level, the tone of “Please
04
Get Acquainted
Function Description

Case Port Battery Port
05
Charge” will sound, required to replace battery or recharge the
battery.
● Monitor
This function can be realized by the long press of the default key.
Press the monitor key, the Signal Indicate will change to Green.
● QT and DQT
This function mainly uses to avoid irrelative calling in caertain
channel. With this function, users can receive calling in
corresponding channels only with the same QT/DQT.
● VOX Function
VOX is a function that voice can be launched without pressing the
PTT key,operation details:Operation details：Switch to channel 7
first, then turn off the radio. Press“CH+”key, turn on the radio at the
same time. There will be a voice "VOX ON" or "VOX OFF".
Attaching & Removing

06
Technical Parameters
General
Operating Frequency
Output Power
Channels
Modulation Type
Antenna
Antenna Gain
Bandwidth
Power Source
Dimension
FRS
≤2W
16
FM(F3E)
Integrated Antenna
1.8dBi
12.5KHz/25KHz
DC3.7V
96*55*22mm
Receiver
Sensitivity
Squelch Sensitivity
Intermodulation
Audio Power
Current
Squelch current
<0.16μV (12dB SINAD)
<0.2μV
50dB
≥300mW
≤100mA
20mA
Transmit
The maximum deviation
Residual radiation
Current
≤±5KHz
<60dB
≤1000mA

RF ENERGY EXPOSURE AND PRODUCT SAFETY GUIDE FOR
PORTABLE TWO-WAY RADIOS
This two-way radio uses electromagnetic energy in the radio frequency
(RF) spectrum to provide communications between two or more users
over a distance. RF energy, which when used improperly, can cause
biological damage.
All Retevis two-way radios are designed, manufactured, and tested to
ensure they meet government-established RF exposure levels. In ad-
dition, manufacturers also recommend specific operating instructions
to users of two-way radios. These instructions are important because
they inform users about RF energy exposure and provide simple
procedures on how to control it.
Please refer to the following websites for more information on what
RF energy exposure is and how to control your exposure to assure
compliance with established RF exposure limits:
http://www.who.int/en/
Local Government Regulations
When two-way radios are used as a consequence of employment, the
Local Government Regulations requires users to be fully aware of and
able to control their exposure to meet occupational requirements.
Exposure awareness can be facilitated by the use of a product label
directing users to specific user awareness information. Your Retevis
two-way radio has a RF Exposure Product Label. Also, your Retevis
user manual, or separate safety booklet includes information and
Warnings
07
Before using this radio, read this guide which
contains important operating instructions for safe
usage and RF energy awareness and control for
compliance with applicable standards and
regulations.

operating instructions required to control your RF exposure and to
satisfy compliance requirements.
Radio License
Governments keep the radios in classification, business two-way
radios operate on radio frequencies that are regulated by the local
radio management departments (FCC, ISED, OFCOM, ANFR, BFTK,
Bundesnetzagentur...).To transmit on these frequencies, you are
required to have a license issued by them. The detailed classification
and the use of your two radios, please contact the local government
radio management departments.
Use of this radio outside the country where it was intended to be dist-
ributed is subject to government regulations and may be prohibited.
Unauthorized modification and adjustment
Changes or modifications not expressly approved by the party resp-
onsible for compliance may void the user’s authority granted by the
local government radio management departments to operate this
radio and should not be made. To comply with the corresponding
requirements, transmitter adjustments should be made only by or
under the supervision of a person certified as technically qualified to
perform transmitter maintenance and repairs in the private land mobile
and fixed services as certified by an organization representative of the
user of those services.
Replacement of any transmitter component (crystal, semiconductor,
etc.) not authorized by the local government radio management dep-
artments equipment authorization for this radio could violate the rules.
FCC Requirements:
This device complies with part 15 of the FCC Rules. Operation is
subject to the condition that this device does not cause harmful
interference. (Licensed radios are applicable);
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions: (Other devices are applicable)
08

(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interfer-
ence that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the
limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communic-
ations. Operation of this equipment in a residential area is likely to cause
harmful interference in which case the user will be required to correct the
interference at his own expense.
CE Requirements:
• (Simple EU declaration of conformity) Shenzhen Retevis Technology
Co., Ltd. declares that the radio equipment type is in compliance with
the essential requirements and other relevant provisions of RED Dire-
ctive 2014/53/EU and the ROHS Directive 2011/65/EU and the WEEE
Directive 2012/19/EU; the full text of the EU declaration of conformity is
available at the following internet address: www.retevis.com.
• Restriction Information
This product can be used in EU countries and regions, including:
Belgium (BE), Bulgaria (BG), Czech Republic (CZ), Denmark (DK),
Germany (DE), Estonia (EE), Ireland (IE), Greece (EL), Spain (ES),
France (FR), Croatia (HR), Italy (IT), Cyprus (CY), Latvia (LV), Lithuania
(LT), Luxembourg (LU), Hungary (HU), Malta (MT), Netherlands (NL),
Austria (AT), Poland (PL), Portugal (PT), Romania (RO), Slovenia (SI),
Slovakia (SK), Finland (FI), Sweden (SE) and United Kingdom (UK).
For the warning information of the frequency restriction, please refer to
the package or manual section.
• Disposal
The crossed-out wheeled-bin symbol on your product, literature,
or packaging reminds you that in the European Union, all
09

electrical and electronic products, batteries, and accumulators (rech-
argeable batteries) must be taken to designated collection locations
at the end of their working life. Do not dispose of these products as
unsorted municipal waste. Dispose of them according to the laws in
your area.
IC Requirements:
Licence-exempt radio apparatus
This device contains licence-exempt transmitter(s)/receiver(s) that
comply with Innovation, Science and Economic Development Cana-
da’s licence-exempt RSS(s). Operation is subject to the following two
conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference
that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada appli-
cables aux appareils radio exempts de licence. L’exploitation est
autorisée aux deux conditions suivantes :
(1) l’appareil ne doit pas produire de brouillage;
(2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectriq-
ue subi, même si le brouillage est susceptible d’en compromettre
le fonctionnement.
RF Exposure Information
• DO NOT operate the radio without a proper antenna attached, as
this may damage the radio and may also cause you to exceed RF
exposure limits. A proper antenna is the antenna supplied with this
radio by the manufacturer or an antenna specifically authorized by
the manufacturer for use with this radio, and the antenna gain shall
not exceed the specified gain by the manufacturer declared.
• DO NOT transmit for more than 50% of total radio use time, more
than 50% of the time can cause RF exposure compliance requirem-
ents to be exceeded.
• During transmissions, your radio generates RF energy that can
10

possibly cause interference with other devices or systems. To
avoid such interference, turn off the radio in areas where signs are
posted to do so.
• DO NOT operate the transmitter in areas that are sensitive to elect-
romagnetic radiation such as hospitals, aircraft, and blasting sites.
• Portable Device, this transmitter may operate with the antenna(s)
documented in this filing in Push-to-Talk and body-worn configurat-
ions. RF exposure compliance is limited to the specific belt-clip and
accessory configurations as documented in this filing and the
separation distance between user and the device or its antenna
shall be at least 2.5 cm.
• Mobile Device, during operation, the separation distance between
user and the antenna subjects to actual regulations, this separation
distance will ensure that there is sufficient distance from a properly
installed externally-mounted antenna to satisfy the RF exposure
requirements.
• Occupational/Controlled Radio, this radio is designed for and classi-
fied as “Occupational/Controlled Use Only”, meaning it must be used
only during the course of employment by individuals aware of the
hazards, and the ways to minimize such hazards; NOT intended for
use in a General population/uncontrolled environment.
• General population/uncontrolled Radio, this radio is designed for
and classified as “General population/uncontrolled Use”.
RF Exposure Compliance and Control Guidelines and Operating
Instructions
To control your exposure and ensure compliance with the
occupational/controlled environment exposure limits, always adhere
to the following procedures.
Guidelines:
• User awareness instructions should accompany the device when
transferred to other users.
• Do not use this device if the operational requirements described
11

herein are not met.
Operating Instructions:
• Transmit no more than the rated duty factor of 50% of the time. To
Transmit (Talk), push the Push to Talk (PTT) button. To receive calls
(listen), release the PTT button. Transmitting 50% of the time, or less,
is important because the radio generates measurable RFenergy
exposure only when transmitting in terms of measuring for standards
compliance.
• Transmit only when people outside the vehicle are at least the reco-
mmended minimum lateral distance away from a properly installed
according to installation instructions, externally mounted antenna.
• When operating in front of the face, worn on the body, always place
the radio in a Retevis approved clip, holder, holster, case, or body
harness for this product. Using approved body-worn accessories is
important because the use of Non-Retevis approved accessories
may result in exposure levels, which exceed the IEEE/ICNIRP RF
exposure limits.
Hand-held Mode
• Hold the radio in a vertical position with the microphone
(and other parts of the radio including the antenna) at
least 2.5 cm (one inch) away from the nose or lips. The
antenna should be kept away from the eyes. Keeping
the radio at a proper distance is important as RF
exposure decreases with increasing distance from the antenna.
Phone Mode
• When placing or receiving a phone call, hold your radio product as
you would a wireless telephone. Speak directly into the microphone.
Electromagnetic Interference/Compatibility
NOTE: Nearly every electronic device is susceptible to electromagnetic
interference (EMI) if inadequately shielded, designed, or otherwise
12

configured for electromagnetic compatibility.
Avoid Choking Hazard
Small Parts. Not for children under 3 years.
Turn off your radio power in the following conditions:
• Turn off your radio before removing (installing) a battery or
accessory or when charging battery.
• Turn off your radio when you are in a potentially hazardous
environments: Near electrical blasting caps, in a blasting
area, in explosive atmospheres (inflammable gas, dust
particles, metallic powders, grain powders, etc.).
• Turn off your radio while taking on fuel or while parked at
gasoline service stations.
To avoid electromagnetic interference and/or compatibility
conflicts
• Turn off your radio in any facility where posted notices
instruct you to do so, hospitals or health care facilities
(Pacemakers, Hearing Aids and Other Medical Devices)
may be using equipment that is sensitive to external RF
energy.
• Turn off your radio when on board an aircraft. Any use of
a radio must be in accordance with applicable regulations
per airline crew instructions.
Protect your hearing:
• Use the lowest volume necessary to do your job.
• Turn up the volume only if you are in noisy surroundings.
• Turn down the volume before adding headset or earpiece.
• Limit the amount of time you use headsets or earpieces
at high volume.
13
WARNING
WARNING

• When using the radio without a headset or earpiece, do
not place the radio's speaker directly against your ear
• Use careful with the earphone maybe possible excessive
sound pressure from earphones and headphones
can cause hearing loss
Note: Exposure to loud noises from any source for extended
periods of time may temporarily or permanently affect your
hearing. The louder the radio's volume, the less time is requ-
ired before your hearing could be affected. Hearing damage
from loud noise is sometimes undetectable at first and can
have a cumulative effect.
Avoid Burns
Antennas
• Do not use any portable radio that has a damaged antenna.
If a damaged antenna comes into contact with the skin
when the radio is in use, a minor burn can result.
Batteries (If appropriate)
• When the conductive material such as jewelry, keys or cha-
ins touch exposed terminals of the batteries, may complete
an electrical circuit (short circuit the battery) and become
hot to cause bodily injury such as burns. Exercise care in
handling any battery, particularly when placing it inside a
pocket, purse or other container with metal objects。
Long transmission
• When the transceiver is used for long transmissions, the
radiator and chassis will become hot.
Safety Operation
Forbid
• Do not use charger outdoors or in moist environments,
use only in dry locations/conditions.
• Do not disassemble the charger, that may result in risk
14
WARNING
WARNING

of electrical shock or fire.
• Do not operate the charger if it has been broken or
damaged in any way.
• Do not place a portable radio in the area over an air bag
or in the air bag deployment area. The radio may be
propelled with great force and cause serious injury to
occupants of the vehicle when the air bag inflates.
To reduce risk
• Pull by the plug rather than the cord when disconnecting
the charger.
• Unplug the charger from the AC outlet before attempting
any maintenance or cleaning.
• Contact Retevis for assistance regarding repairs and
service.
• The adapter shall be installed near the equipment and
shall be easily accessible
Approved Accessories
• This radio meets the RF exposure guidelines when used
with the Retevis accessories supplied or designated for
the product. Use of other accessories may not ensure
compliance with the RF exposure guidelines and may
violate regulations.
• For a list of Retevis-approved accessories for your radio
model, visit the following website: http://www.Retevis.com
15
WARNING

Guarantee
Model Number:
Serial Number:
Purchasing Date:
Dealer:
Telephone:
User’s Name:
Telephone:
Country:
Address:
Post Code:
Email:
Remarks:
1. This guarantee card should be kept by the user, no replacement if lost.
2. Most new products carry a two-year manufacturer’s warranty from the date of
purchase. Further details, pls read http://www.retevis.com/after-sale/
3. The user can get warranty and after-sales service as below:
• Contact the seller where you buy.
• Products Repaired by Our Local Repair Center
4. For warranty service, you will need to provide a receipt proof of purchase from the
actual seller for verification
Exclusions from Warranty Coverage:
1. To any product damaged by accident.
2. In the event of misuse or abuse of the product or as a result of unauthorized
alterations or repairs.
3. If the serial number has been altered, defaced, or removed.

Add: 7/F, 13-C, Zhonghaixin Science&Technology Park,
No.12 Ganli 6th Road, Jihua Street, Longgang
District, Shenzhen, China
Web: www.retevis.com
E-mail: [email protected]
Facebook: facebook.com/retevis