REVELL KIT 1907 User manual

AM General’s Hummer is one of most rugged and capable 4X4’s ever
built. Development of the Hummer originally began in 1979, when the U.S.
Army needed a High Mobility Multi-Purpose Wheeled Vehicle (HMMWV, or
“Humvee” for short). The Hummer quickly proved itself as a highly versatile,
effective military vehicle, and became so popular that AM General introduced
a civilian version of the Hummer in 1992. The Hummer remains in widespread
use in the U.S. Army and commercial industries, and is a very popular “status”
vehicle among the general public.
The Hummer’s main body is made of a strong, heat-treated aluminum alloy,
held together with more than 2,800 rivets for unmatched durability. It features
a 4-wheel, fully independent suspension system with heavy-duty springs
and hydraulic shock absorbers, plus a Central Tire Inflation System (CTIS)
that enables the driver to inflate or deflate the Hummer’s tires right from the
driver’s seat for better traction. With its low center of gravity, 72 inch track
width, and a full 16 inches of ground clear-
ance, the Hummer can tackle almost any o f f
road terrain, and with a snorkel kit,
it is capable of fording 60 inches
of water.
Your Revell Snaptite model
kit features easy snap and
screw together assembly, accu-
rate body with separate brush
guard, free rolling wheels on metal a x l e s ,
and colorful customizing stickers. Enjoy building your kit of
HUMMER
KIT 1907 85190710200
Step 15 Sticker Placement Guide
ANY UNUSED PARTS MAY BE DISCARDED
7
BRUSH GUARD
Completed
Assembly
METAL AXLES
& SCREWS
20
TIRES
BODY
COMPLETED
CHASSIS
ASSEMBLY
NOTE:
When applying stickers, avoid touching the “sticky” side to prevent finger prints on stickers. Bend sticker sheet slightly to lift edge of sticker & use a finger-
nail to lift sticker from sheet. Line up sticker on body and press an edge into place, slowly working sticker with a finger nail until sticker is fully on model.
If you have any questions or comments, call our hotline at: [phone]
or, please write to:
Revell-Monogram Consumer Service Department, 725 Landwehr Road,
Northbrook, Illinois 60062
Be sure to include the plan number (85190710200), part number, description,
your return address and phone number.
Visit our website: www.revell-monogram.com
CAUTION:
POSITION ALL PARTS IN THIS KIT CAREFULLY. PARTS
WILL ONLY SNAP TOGETHER ONCE.
* REPEAT SEVERAL TIMES
* A REPETER PLUSIEURS FOIS
* REMOVE AND THROW AWAY
* A RETIRER ET JETER
* APPLY STICKERS
*APPLIQUEZ LES AUTO-COLLANTS
* REPEAT SEVERAL TIMES
* A REPETER PLUSIEURS FOIS
READ BEFORE YOU BEGIN
• CLEAR A SPACE TO WORK ON
• STUDY THE ASSEMBLY DRAWINGS BEFORE YOU BEGIN
• EACH PLASTIC PART IS IDENTIFIED BY A PART NUMBER
• DO NOT OVER TIGHTEN SCREWS
• SEE NOTE ABOUT APPLYING STICKERS IN STEP #15
REVELL-MONOGRAM LLC Northbrook, IL. Copyright © 2003. All rights reserved.
Step 14Step 13
Parts Included
5
SCREWS
BODY ASSEMBLY
FRONT
21
7
8
9
12
13
10
6
18 19
17
11
11
18
19
7
6
4
6
7
2
3
2
1

FRONT
UNDERSIDE
SHOWN
851907100200
1
BODY
20
WINDSHIELD &
REAR WINDOW
(CLEAR)
8
STICKER
11
SEAT
10
INTERIOR TUB
13
STEERING WHEEL
12
DASHBOARD
INTERIOR TUB
ASSEMBLY
COMPLETED
INTERIOR
ASSEMBLY
9
ROLL BAR
BRACE
18
WHEEL BACK
METAL AXLE
17
COIL
SPRING
Step 2 Step 3 Step 4
Step 5 Step 8
Step 9 Step 10 Step 11
Step 1
Step 6 Step 7
Step 12
9
STICKER
11
SEATS
11
SEATS
COMPLETED
DASHBOARD
ASSEMBLY
21
HEADLIGHTS
(CLEAR)
19
WHEEL FRONT
REAR
TIRE
8
ROLL BAR
BRACE
PUSH
DOWN
SPRINGS SHOULD ANGLE
TOWARD CENTER OF CHASSIS
*
* *
* *