RGBlink M1 User manual

M1 Quick Start
Support signal cross conversion
Support pixel-to-pixel scaling
Support four modular inputs
Support HDMI & SDI outputs
Support touch screen control
Integrated audio
Support configurable PIP
Support Transition effects, DSK, Blending
Support Genlock
Support direct access to stored presets

Address：S603-604 Weiye Building Torch Hi-Tech Industrial Development Zone Xiamen, Fujian Province, P.R.C
Tel: [phone] Fax: [phone]
Email: [email protected] http://www.rgblink.cn
2
CONTENT
Product Introduction................................................................................................................................................... 3
Packing Configuration................................................................................................................................................. 4
Hardware Orientation................................................................................................................................................. 5
Rear Panel............................................................................................................................................................5
Back Panel........................................................................................................................................................... 8
Using Your Product...................................................................................................................................................... 9
Menu Structure................................................................................................................................................... 9
PST Mode...........................................................................................................................................................11
PGM Mode........................................................................................................................................................ 15
Switching Mode.................................................................................................................................................16
Set the Output Parameter.................................................................................................................................17
Using Black Out................................................................................................................................................. 18
Saving Views...................................................................................................................................................... 19
Recall Saved Settings......................................................................................................................................... 20
Contact Information.................................................................................................................................................. 21

Address：S603-604 Weiye Building Torch Hi-Tech Industrial Development Zone Xiamen, Fujian Province, P.R.C
Tel: [phone] Fax: [phone]
Email: [email protected] http://www.rgblink.cn
3
Product Introduction
M1 is All-in-one scaling and vision mixing Tools.
M1 can be up-down cross-covert any input signal to output, support 2 layers switching from preview to
PGM.support Integrated audio .Both LCD touch screen and Menu rotation can be operation M1.M1 via one
HDMI port of PVW output module come ture preview combined windows for PGM+PVW+PST.
Now you choose input options, now you configure output operations, now control transitions from the T-bar,
now do more.
M1 redefines modern hands on scaling and mixing for any environment.
Totally modular and flexible in configuration, M1 is packed with standard features to impress and present with
ease.
System Connection
RGBlink offers solutions to demanding
technical problems. Any application
questions, or required further
information, please contact with our
customer Support Engineers.
M1 System Connection Diagram

Address：S603-604 Weiye Building Torch Hi-Tech Industrial Development Zone Xiamen, Fujian Province, P.R.C
Tel: [phone] Fax: [phone]
Email: [email protected] http://www.rgblink.cn
4
Packing Configuration
Note:
AC Power Cable supplied as standard according to destination market.
USB is contained on the Warranty/Registration Card. Please keep.
Network Cable
USB Cable
QC Declaration
Warranty Card &
USB Files
Antistatic Bag
Screw Driver
HDMI to DVI
Cable
AC Power Cable

Address：S603-604 Weiye Building Torch Hi-Tech Industrial Development Zone Xiamen, Fujian Province, P.R.C
Tel: [phone] Fax: [phone]
Email: [email protected] http://www.rgblink.cn
5
Hardware Orientation
Rear Panel
Panel Instruction
1
Audio adjust area
5
Switching modes area
2
Presets operation area
6
Layer function area
3
Input sources area
7
Layer selection area
4
Menu and LCD display area

Address：S603-604 Weiye Building Torch Hi-Tech Industrial Development Zone Xiamen, Fujian Province, P.R.C
Tel: [phone] Fax: [phone]
Email: [email protected] http://www.rgblink.cn
6
Audio adjust area
1
SOURCE FADER
Source fader adjust 4 input signals' voice separatly to same value, each signal request
to save .
MASTER FADER
MASTER FADER is an amplification-factor of all channel invoice, come true Source value
multiply by current Master value
CUE
EARPHONE voice = PST (MultiView HDMI port) voice channel can be via CUE tranfer to
PGM
MUTE
MUTE only for PGM voice.
Presets operation area
2
SAVE
Support 36 saving modes.
LOAD
Load saving views 1 to 36.
PAGE
For save or load, total 5 pages, and 5 banks for each page.
1/2/3/4/5
The button is lit when select PAGE or BANK.
Input Sources Area
3
LED Indicator
The button 1/2/3/4/LOGO is lit when the signal or background input is selected for use.
PGM Area
For indicating, user can not change the channel or set the size or position in PGM area.
LOGO
Enable or disable the LOGO function. If select “ON”, user can set the X and Y, or load file
from UDisk.
1/2/3/4/5/6/7/8/9/0
Each button is numbered and can be used as direct number entry when values such as
resolution and size.
PST Area

Address：S603-604 Weiye Building Torch Hi-Tech Industrial Development Zone Xiamen, Fujian Province, P.R.C
Tel: [phone] Fax: [phone]
Email: [email protected] http://www.rgblink.cn
7
For indicating, the button is lit when output the signal in PST channel.
For selecting, push any button to switch the PST signal.
For editing, (button light is lit -- the channel is used but can not be edited, button light
is flashing -- the channel can be edited, button light is off -- the channel is not selected.
Menu and LCD Display Area
4
MENU
Menu and exit reuse button.
SELECT/ENTER
Confirmation button.
LCD Display
Displays current status of the product, and for feature selections provides interactive
choices in conjunction with buttons on the Rear Panel.
Switch Mode Area
5
CUT
Zero delay switching.
TAKE
Seamless switching with transition effects.
T-BAR
WIPE and mix switching.
Layer Function Area
6
Mask
Key the video into special shape including diamond, round, heart, star, triangle.
SCALE
This button used for size and crop adjusting. If image quality distorts by improper
operation, it can be recover by reset.
Layer Selection Area
7
A/B
For adding or deleting the layer, the button light is lit when add the layer, off when
delete the layer, and flash when select the layer.

Address：S603-604 Weiye Building Torch Hi-Tech Industrial Development Zone Xiamen, Fujian Province, P.R.C
Tel: [phone] Fax: [phone]
Email: [email protected] http://www.rgblink.cn
8
Back Panel
Input Interface
Optional
Input
Module
1
4 input card slots, supports input signals including DVI, HDMI, USB, SDI.
Each DVI module supports 1 DVI-I input and compatible CVBS, VGA,Ypbpr , VGA
Each HDMI module supports 1 HDMI-A input .
Each USB module supports 1 USB-A input and 1 USB backup.
Each SDI module supports 1 SDI input and 1 SDI loop out.
Output Interface
PVW Output
2
HDMI Output
PGM Output
3.4
HDMI output and SDI output
Audio Area
5
Audio In
Audio Out
Audio Out( Earphone)
Control Interface
6
Genlock input BNC port
7
LAN port RJ-45
8
USB port USB-A
9
TALLY light
Power Connection
10
Power Switch

Address：S603-604 Weiye Building Torch Hi-Tech Industrial Development Zone Xiamen, Fujian Province, P.R.C
Tel: [phone] Fax: [phone]
Email: [email protected] http://www.rgblink.cn
9
11
AC 85-264V Max 65W, IEC-3
Using Your Product
Menu Structure
The menu structure is shown on the LCD Screen and in the figure below:
LCD Touch Screen Menu Instruction
1
Return Button
12
DSK
2
Homepage
13
BLEND
3
Information Page
14
FREEZE
4
Input Resolution Display
15
BLACK
5
output Resolution Display
16
Audio In
6
Input Menu
17
Audio Out
7
Output Menu
18
Lock Rear Panel
8
LOGO
19
Language/语言
9
MASK
20
System
10
Scale
21
Factory Reset
11
Transition Effect

Address：S603-604 Weiye Building Torch Hi-Tech Industrial Development Zone Xiamen, Fujian Province, P.R.C
Tel: [phone] Fax: [phone]
Email: [email protected] http://www.rgblink.cn
10

Address：S603-604 Weiye Building Torch Hi-Tech Industrial Development Zone Xiamen, Fujian Province, P.R.C
Tel: [phone] Fax: [phone]
Email: [email protected] http://www.rgblink.cn
11
PST Mode
M1 supports 1 HDMI preview output, and it supports the functions as below:
Signal Selection
Push any button in Input Sources Area, for example, push the button [5], the border of signal 5 will change to
yellow, and the signal in PGM monitor will be changed to signal 5.
Add or Delete Layer
Push any button of [A] to [B] in Layer Selection Area to add or delete the layer.
Add layer: The light is lit.
Select layer: The light is flashing.
Delete layer: The light is off.
Freeze the Layer(N/A, coming soon)
Push the [FREEZE] button in Layer Adjustment Area, the layer will be freeze, push the button again, the layer is
live.
2 Layers Presets
1. Push A or B button in Layer selection Area to select 1 or 2 layouts, including 1P, PIP.
2. User can adjust the position, size for the selected layer, and set DSK, BLEND and MASK, some function
coming soon.
Set the Position
1. Push any button of [A] to [B] in Layer Selection Area, the light is red lit when the layer is selected.
2. Push the [SCALE] button in Layer Adjustment Area, and enter to the menus as follows:
Use the rotary knob to adjust the position of the layer.
Scale and Crop the Layer
1. Push any button of [A] to [B] in Function Selection Area, the light is flashing when the layer is selected.
2. Push the [SCALE] button in Layer Adjustment Area, and enter to the menus as follows:
->H Pos 120
V Pos 329
H Size 1920
V Size 1920
->H Size 1920
V Size 1080
Reset >>
Crop H Pos 0

Address：S603-604 Weiye Building Torch Hi-Tech Industrial Development Zone Xiamen, Fujian Province, P.R.C
Tel: [phone] Fax: [phone]
Email: [email protected] http://www.rgblink.cn
12
Use the rotary knob to adjust the size of the layer.
If select <Crop>, it will enter to the menus as follows:
Crop H Pos: Crop the horizontal position.
Crop V Pos: Crop the vertical position.
Crop H Size: Crop the horizontal size.
Crop V Size: Crop the vertical size.
Reset: Reset crop if image quality distorts by improper operation.
DSK Setting
1. Firstly, enable the 2 layers function.
2. Push [MENU] button, and enter to the menu items. Turn the rotary knob, and select <DSK> option in LCD
screen, rotary the knob or touch the <DSK> to confirm.
Preset: Can select user, black background, white background, red background, green background and blue
background.
Mode: Select Key In or Key Out.
Alpha: The adjustment range is between 0~128.
Red Min: The adjustment range is between 0~255.
Red max: The adjustment range is between 0~255.
Green Min: The adjustment range is between 0~255.
Green Max: The adjustment range is between 0~255.
Blue Min: The adjustment range is between 0~255.
Blue Max: The adjustment range is between 0~255.
DSK: Can select enable or disable the DSK function.
Transitions Setting
1. Touch the transition buttons in Transition Menu, M1 supports 13 kinds of wipe modes:
Preset User
Mode Key In
Alpha 128
->Red Min 0
Red Max 208
Green Min 0
Green Max 208
->Blue Min 0
Blue Max 208
DSK ON

Address：S603-604 Weiye Building Torch Hi-Tech Industrial Development Zone Xiamen, Fujian Province, P.R.C
Tel: [phone] Fax: [phone]
Email: [email protected] http://www.rgblink.cn
13
Touch the transition button , user can select ←[]→.
Touch the transition button , can select L→R.
Touch the transition button , user can select T→B.
Touch the transition button , can select fade.
Touch the transition button , user can select LT→RB.
Touch the transition button , user can select ←＋→.
Touch the transition button , user can select L←R.
Touch the transition button , user can select B→T.
Touch the transition button , user can select L←M→R.
Touch the transition button , user can select T←M→B.
Touch the transition button , user can select →+←.
Touch the transition button , user can select III→.
Touch the transition button , user can select ←O→.
2. Push the [TAKE] button, or use T-bar switcher to switch the image to program with selected wipe.
Audio In Setting
1. Push [MENU] button, and enter to the menu items. Turn the rotary knob, select <Audio In> option in LCD
screen, rotary the knob or touch the <Audio in>directly to confirm.
2. Select the Audio input 1-4 for setting :
Audio Source Sel: Embedded or External
Audio Gain: The adjustment range is between 0~100
Audio Delay: The adjustment range is between 0~20ms
Audio Source Sel Embedded
Audio Gain 0
Audio Delay 0

Address：S603-604 Weiye Building Torch Hi-Tech Industrial Development Zone Xiamen, Fujian Province, P.R.C
Tel: [phone] Fax: [phone]
Email: [email protected] http://www.rgblink.cn
14
Audio Out Setting
1. Push [MENU] button, and enter to the menu items. Turn the rotary knob, select <Audio Out> option in LCD
screen, rotary the knob or touch the <Audio Out>directly to confirm.
2. Select the Audio Output for setting :
Audio Source Sel: Select Layer A or Layer B
Audio Gain: The adjustment range is between 0~100
Monitor Select: Select PST or PGM
Mute: Select On or Off
BLEND Setting(Coming Soon)
Mask Setting(Coming Soon)
Custom LOGO(Coming Soon)
Audio Source Sel Layer A
Audio Gain 0
Monitor Select 0
Mute On

Address：S603-604 Weiye Building Torch Hi-Tech Industrial Development Zone Xiamen, Fujian Province, P.R.C
Tel: [phone] Fax: [phone]
Email: [email protected] http://www.rgblink.cn
15
PGM Mode
1. Switch the edited PST image to program by pushing the [CUT], [TAKE] button or T-bar, and then the PGM
image will return to PST state, which can be edited.
2. There are 1 HDMI output and 1SDI output for program, and realize 2Kx1K output.

Address：S603-604 Weiye Building Torch Hi-Tech Industrial Development Zone Xiamen, Fujian Province, P.R.C
Tel: [phone] Fax: [phone]
Email: [email protected] http://www.rgblink.cn
16
Switching Mode
1. T-BAR switch: Switch the PST image to program with wipe and fade by T-bar.
2. CUT switch: Seamless switch the PST image to program by pushing [CUT] button.
3. TAKE switch: Switch the PST image to program with wipe and fade by pushing [TAKE] button.
4. CUE switch: EARPHONE voice via CUE transfer PST to PGM
5. MUTE switch: MUTE only for PGM voice.

Address：S603-604 Weiye Building Torch Hi-Tech Industrial Development Zone Xiamen, Fujian Province, P.R.C
Tel: [phone] Fax: [phone]
Email: [email protected] http://www.rgblink.cn
17
Set the Output Parameter
1. Select the Output Resolution
Push the [MENU] button, and enter to the menu items, turn the rotary knob and select <Output>:
Push the rotary knob to confirm, and enter to the menus as below:
<Output Format> is the default option, push the rotary to confirm. Turn the rotary knob, select the output
resolution according to actual need.
2. Output Setting
Push the rotary knob or touch the button <Output setting> to confirm, and enter to the menus as below:
PST and PGM can be choose DVI or HDMI as output port, SDI Level choose Level A or Level B.
3. External Sync
External Including option Off and On, Input will shown as actual input. Format support choose 2 default
resolution: 1280x720 @60 & 1920x1080 @60.
Output Format Output Setting External Sync
PST DVI
PGM DVI
SDI Level Level A
External Sync
External Off
Input No Input
Format 1920x1080 @60

Address：S603-604 Weiye Building Torch Hi-Tech Industrial Development Zone Xiamen, Fujian Province, P.R.C
Tel: [phone] Fax: [phone]
Email: [email protected] http://www.rgblink.cn
18
Using Black Out
This function will coming soon.
Black out description:
Black signal realizes one-key-touch to a black screen.
M1 provides black effect processing for program output and preview output, with cut black effect. Operation is
as below:
Touch the [BLACK] button, then the program output is cut to black.
The effect is shown as below:

Address：S603-604 Weiye Building Torch Hi-Tech Industrial Development Zone Xiamen, Fujian Province, P.R.C
Tel: [phone] Fax: [phone]
Email: [email protected] http://www.rgblink.cn
19
SAVE TO
->PAGE: 1
BANK: 1
SAVE TO
PAGE: 2
->BANK: 2
Saving Views
M1 provides 25 positions for saving or recording parameters. To save current parameters and settings:
1. Push the [SAVE] button in Presets operation area, the button [SAVE] and [PAGE] lights are lit, and some of
buttons 1~5 are lit and some are flashing. The button lit can be saved and flash will be overwrite, push the
button lit to save.
2. Select PAGE, for example, the button [2] is lit, push the button [2].
3. After set the PAGE, it will jump to BANK option, or example, the button [2] is lit, push the button [2]:
4. Push the [SAVE] button again, the button light is off, and exit the save function.
SAVE TO
->PAGE: 2
BANK: 1

Address：S603-604 Weiye Building Torch Hi-Tech Industrial Development Zone Xiamen, Fujian Province, P.R.C
Tel: [phone] Fax: [phone]
Email: [email protected] http://www.rgblink.cn
20
LOAD FROM
->PAGE: 1
BANK: 1
LOAD FROM
PAGE: 2
->BANK: 2
Recall Saved Settings
M1 provides 25 positions for saving or recording parameters. To recall saved settings:
1. Push the [LOAD] button in Presets operation area, the button [LOAD] and [PAGE] lights are lit, and some of
buttons 1~5 are lit and some are flashing. The button lit is ready for recall and flash means just recall, push
the button lit to recall.
2. Select PAGE, for example, the button [2] is lit, push the button [2].
3. After set the PAGE, it will jump to BANK option, or example, the button [2] is lit, push the button [2]:
4. Push the [LOAD] button again, the button light is off, and exit the load function.
LOAD FROM
->PAGE: 2
BANK: 1