RH Teen FRENCH LIBRARY SINGLE STORAGE DESK User manual

Page 1 of 4
TEEN
F R E N C H L I B R A R Y S I N G L E S T O R A G E D E S K
Center Section 11
2
3
Sr.No. Item Description Qty.
Cross Bracing 1
4
Desk Front Support Angle 1
5
6
7
8
A
B
E
F
G
H
I
J
K
L
1Left Section
2
1
Top Support Angle
Bottom Support Angle
C
D
Left Top Shelf
Right Top Shelf
Narrow Shelf
Wide Shelf
1
1
2
1
Screws 27+3
2Wrench
9 M 3Cast Iron Handles
Customer Service - If you are missing parts or have any questions about this product
please contact us at : 1-800-762-1751
IMPORTANT SAFETY INSTRUCTIONS:
For your safety, it is recommended that two people assemble the unit.
These instructions are provided for your safety. It is important that they are read carefully and completely
before installation of the fixture.

ASSEMBLY INSTRUCTIONS
1. Carefully unpack the contents of the carton.
2. Assemble the unit as close to its final location as possible.
3. Place Center Section (A) away from wall and place Left Section (B) next to it.
4. Remove all the pre-installed bolts from the back of Center Section (A) & Left Section (B).
Place one of the Top Support Angles (C) on top and re-tighten the bolts back in place.
5. Slightly lift the unit and slide Bottom Support Angle (D) underneath and tighten the
bolts back in place.
6. Place Cross Bracing (E) at the back of unit connecting Left Section (B) with Center
Section (A) and tighten the bolts back in place.
Page 2 of 4
TEEN
A
C
B
D
E
E6
4
5
F R E N C H L I B R A R Y S I N G L E S T O R A G E D E S K

F
Top Shelf Top Shelf
I
I
J
GH
8
9
10
7. Slide the unit towards the
wall, to the desired final
location.
8. Remove all the pre-installed
bolts from the front of the
unit & place the other Top
Support Angle (C) on Top
and re-tighten the bolts
back in place.
9. Place Cast Iron Handles
(M) on all the Sections and
tighten the bolts back in
place.
10. Place Desk Front Support
Angles (F) and re-tighten
the bolts.
12
12
11. Place all the Shelves (G-J) into the
slots as shown.
12. Screw (K) all the Shelves in place
(G-J) as shown in picture 12.
Page 3 of 4
M M
TEEN
F R E N C H L I B R A R Y S I N G L E S T O R A G E D E S K
M

13. Open the drawers and unscrew the handles from inside the drawers (13A). Re-screw the
handles onto the fronts of drawers (13B).
Page 4 of 4
TEEN
13A
13B
F R E N C H L I B R A R Y S I N G L E S T O R A G E D E S K

FIGURE 2
Hardware Included:
FURNITURE TIPPING RESTRAINT INSTRUCTION
Thank you for your purchase
Wall
Bracket :
2 Pcs.
Screws :
4 Pcs.
Nylon Strap :
2 Pcs.
Page 1 of 1
WARNING:
Young children may be injured by tipping furniture and proper installation of the mounting hardware for this
item is highly recommended. When properly installed, this mounting hardware could provide protection against
the unexpected tipping of this furniture piece.
This product is only a deterrent. It is not a substitute for proper adult supervision.
Anchors :
4 Pcs.
CARE INSTRUCTIONS:
To clean, wipe with a soft dry cloth.
Avoid use of harsh chemicals or abrasive cleaners as they may damage the finishes.
TOOLS NEEDED
Phillips head screwdriver (not included)
FIGURE 1
ASSEMBLY INSTRUCTIONS:
1. Determine the final position of the furniture piece. Mark location on the
wall approximately 2" below the top of the furniture.
2. Drill a starter hole into the wall stud. If wall stud is not available, drill a hole
into the wall and insert plastic anchor. Gently tap the anchor until the
flange of the anchor is flush with the wall.
3. Place the furniture so the Side Panels (A) are in line with the brackets on
the wall.
4. Lace the supplied nylon straps through the wall bracket & around the side
panel. Bring both ends together and slide the beaded end until it snap locks
into the keyhole slot.
5. To double lock, return the beaded ends back through keyholes.
6. Check to make sure the straps are securely laced and locked to the
brackets.