RH Teen COLBIN BUNK BED - TWIN OVER TWIN User manual

WARNING: Read all
instructions before assembling this
product. KEEP INSTRUCTIONS
FOR FUTURE USE.
C O L B I N STORAGE B U N K B E D - T W I N O V E R T W I N - A S S E M B L Y I N S T R U C T I O N S
CUSTOMER SERVICE
If you are missing parts or have any questions about this product, contact us first. You can also order parts by writing to the address above. Include the
product model number, color, and a brief description of the part.
Call 1-800-762-1751.
CARE AND CLEANING
DO NOT scratch or chip the finish. DO NOT use abrasive chemicals for cleaning. Dust often using a clean, soft, dry cloth. Blot spills immediately and wipe
with a clean damp cloth. If the crib is to be stored, store in a cool dry place and carefully package all original hardware to protect from loss.
TOOLS AND INSTALLATION
Tools Necessary: Allen key (included)
Wrench (included)
Screwdriver (not included)
Note: It may be easier to assemble product with two people.
NOTE: When inserting bolts, turn clockwise until tight. Then loosen 12- 34of a turn. After bunks is completely assembled, return to each bolt and tighten. Use
wax or soap on all bolts to facilitate assembly.
111
/

IMPORTANT SAFETY INFORMATION FOR BUNK BED
1. Follow the information on the WARNINGS appearing on the upper bunk end
structure and on the carton.
2. Always use the specified size mattress, mattress support, or both to help
prevent the likelihood of entrapment or falls.
3. Surface of mattress must be at least 5 inches below the upper edge of
guardrails on top bunk.
4. Do not allow children under 6 years of age to use the upper bunk.
5. Prohibit more than one person on upper bunk.
6. Periodically check and ensure that the guardrails, ladder, and other
components are in their proper position, free from
damage, and that all connectors are tight.
7. Do not allow horseplay on or under the bed and prohibit jumping on the bed.
8. Always use the ladder for entering and leaving the upper bunk.
9. Do not use substitute parts. Contact Restoration Hardware for replacement
parts.
10.Use of a night light may provide added safety precaution for a child using
the upper bunk.
11.Use guardrails on both sides of the upper bunk.
12.If the bunk bed will be placed next to a wall, the guardrail that runs the full
length of the bed should be placed against the wall to prevent entrapment
between the bed and the wall.
13. The use of water flotation mattress is prohibited.
14.STRANGULATION HAZARD - Never attach or hang items to any part of the
bunk bed that are not designed for use with the bed: for example, but not
limited to, hooks, belts, and jump ropes
15.Keep these instructions for future reference.
16.DO NOT remove warning label from bed.
WARNING
DO NOT REMOVE THIS LABEL
TO HELP PREVENT SERIOUS OR FATAL
INJURIES FROM ENTRAPMENT OR FALLS:
1. Never allow a child under 6 years on upper bunk.
2. Use only mattress which is 38''W x 75L x 7''H on Twin
upper bunk, and 38''W x 75L x 10''H on Twin lower
bunk.
3. Ensure thickness of mattress does not exceed 7" and
mattress is at least 5" below upper edge of guardrails.
4. Use guardrails on both sides of upper bunk.
5. Use ladder for entering and leaving upper bunk.
6. Prohibit horseplay on or under bed(s).
7. Prohibit more than one person on upper bunk.
8. If the bunk bed will be placed next to a wall the
guardrails that run the full length of the bed .
STRANGULATION HAZARD
9. Never attach or hang items to any part of the bunk bed
that are not designed for use with the bed; for
example, but not limited to, hooks, belts, and jump
ropes.
211
/

PARTS INCLUDED
A [2] HEADBOARD & FOOTBOARD
B [1] STORAGE
C [1] LOWER SIDE RAIL
D [2] UPPER SIDE RAILS
E1 [1] LONG GUARDRAIL
E2 [1] SHORT GUARDRAIL
F1 [3] BED SLATS (LONG)
F2 [3] BED SLATS (SHORT)
G [1] LOWER PLATFORM PANEL
H [2] UPPER PLATFORM PANELS
I [1] LADDER
COMPONENT IDENTIFICATION AND HARDWARE
NO. ITEM DESCRIPTION QTY.
1Threaded Rod 8 pcs.
2Curved Washer 8 pcs.
3Lock Washer 8 pcs.
4
5Wrench 1 pc.
Hex Nut 8 pcs.
Flat Head Phillips Screw
(M4x20mm)
Allen Bolt
Round Head Screw
(M4x25mm)
Plain Washer
Allen Key
Metal bracket 1
Metal bracket 2
Phillips Screwdriver
(Not provided) 1 pc.
14
NO. ITEM DESCRIPTION QTY.
TOOLS REQUIRED (NOT PROVIDED)
HARDWARE FOR UPPER SIDE RAILS & LOWER SIDE RAILS
NO. ITEM DESCRIPTION QTY.
612 pcs.
712 pcs.
812 pcs.
91 pc.
HARDWARE FOR LOWER SIDE RAILS
Lock Washer
NO. ITEM DESCRIPTION QTY.
10 36 pcs.
11 5 pcs.
12 3 pcs.
HARDWARE FOR GUARDRAILS & LADDER
NO. ITEM DESCRIPTION QTY.
13 42 pcs.
HARDWARE FOR SLATS & PLATFORM PANELS
A
A
B
C
D
D
E1
E2
F1
F2
G
H
H
311
/

ASSEMBLY INSTRUCTIONS
1. Place the upper side rails (D) up on a flat surface.
2. Place the Long guardrail (E1) and Short guardrail (E2) on the top of the upper side rails (D), then attach the metal bracket 1 (11) and metal bracket 2
(12) into the side rails and guardrails. Insert screw (10) provided to pass through hole on metal bracket 1 (11) and metal bracket 2 (12) to the pre-drill
hole on side rails and guardrail. Refer to FIGURE 1 & FIGURE 2.
IMPORTANT
These bed parts can be cumbersome and heavy, therefore the assistance of two or more people is recommended in order to prevent personal injury
and ensure the bed parts are not damaged during the assembly process.
FIGURE 1
10
12
FIGURE 2
Fig. 2
Fig. 2
Fig. 1
Fig. 1
E2
E1
DD
10
11
NOTE: The short guardrail can be installed at either end of either upper side rail, depending on your desired ladder location. To install the short
guardrail on the left side of the upper side rail, refer to option A & B. Option C & D show the short guardrail installed on the right of the upper side rail.
OPTION A OPTION B
OPTION C OPTION D
411
/

FIGURE 3
3. Lay the headboard and the footboard (A) on
a flat surface.
4. Attach the threaded rods (1) into the fixed
nuts in the post of the headboard/footboard
by turning them manually. See FIGURE 3.
5. Fully remove all the drawers out of the
storage (B). Attach the storage to the
headboard (A), as per illustration in FIGURE
4. NOTE: SEE DETAIL ON PAGE 9 TO
REMOVE DRAWER.
6. Attach the lower side rail (C) to the
headboard as per illustration in FIGURE 5.
NOTE: Side panel is exchangeable for
ladder placement on either side.
7. Bring the upper side rail with Guardrail
(D&E1) & (D&E2) in upright position and
align the threaded rods on the headboard to
the corresponding holes in the end of the
upper side rail. Attach the upper side rail to
the headboard, as in FIGURE 6, FIGURE 7.
Insert screw (10) provided to pass through
hole on metal bracket of upper side rail to
the pre-drill hole on headboard, as in
FIGURE 8. KEEP HOLDING THIS SIDE
RAIL DURING NEXT STEP.
1
A
FIGURE 4 FIGURE 5
8769
8769
FIGURE 6
2
3
4
5
2
3
4
5
FIGURE 7
FIGURE 8
10
A
E1
D
E2
D
C
B
Fig. 4
Fig. 5
Fig. 6
Fig. 7
Fig. 8
511
/

8. Align the threaded rods on the footboard (A) to the corresponding holes at the end of the storage (B), lower side rail (C) and upper side rails with
guardrail (D&E1), (D&E2). Align the locator pins on the end of the storage and the side rails to the corresponding holes in the footboard. Insert the
footboard into the storage and the side rails.
9. Repeat step 6, 7 to attach the storage and the side rails to the footboard. See SKETCH below.
10. For packing purpose, the handles were reversed. Unscrew to remove all the handles from inside surface of the drawer front panels.
11. Re-install the handle on the correctly position on the drawer front panel, as illustrated in FIGURE 9.
FIGURE 9A
Handle
Phillips
Head Bolt
Phillips
Head Bolt
FIGURE 9B
611
/

12. Set the bed slats (F1, F2) on the upper bunk and lower bunk. Secure each slat by using screws (13) provided. See FIGURE 10.
13. Return the drawers to the storage by FOLLOW STEP BY STEP AT PAGE 10, 11.
14. Hook simultaneously the ladder (I) on the upper side rail an lower side rail. Use screw (10) provided to fix the top and bottom of ladder with side rail.
as per illustration in FIGURE 11 and FIGURE 12.
FIGURE 10
13
10
FIGURE 11
FIGURE 12
10
F1
F2
Fig. 10
Fig. 11
I
711
/

15. Place the platform panels (G/H) on the lower bunk and the
upper bunk, then fix them with screws (13). See FIGURE 13.
16. INSTALL BEDDING
FIGURE 13
13
BEDDING SPECIFICATION:
The following size mattress and foundation are specified for use with this bunk bed.
Mattress: 38''W x 75''L x 7''H on Twin upper bunk, and 38''W x 75''L x 10''H on Twin lower bunk.
**Note: ENSURE THICKNESS OF MATTRESS DOES NOT EXCEED 7" AND MATTRESS IS AT
LEAST 5" BELOW UPPER EDGE OF GUARDRAILS.
Be sure to adhere to these BEDDING SPECIFICATIONS in order to avoid the possibility of falling
or entrapment. THESE SPECIFICATIONS MUST BE STRICTLY ADHERED TO!
UPPER BUNK MATTRESS DIAGRAM
[5''] MINIMUM DISTANCE
FROM TOP OF MATTRESS
TO TOP OF GUARDRAIL
[7'']
MAXIMUM
THICKNESS
PLATFORM PANEL SLAT SUPPORT
SIDE RAIL
GUARD RAIL
G
H
H
811
/

STEP 1: DRAWER REMOVAL INSTRUCTIONS
FIGURE A
STEP 1.2
Hold the drawer with both your hands. Carefully lift the drawer front up from the front metal pin, then slide drawer forward
to remove from back hooks. See FIGURE B.
Plastic
peg
FIGURE B
Metal pin/
Hole for pin
STEP 1.1
Pull the drawer out. See at bottom side of drawer. Unlock the plastic peg by pulling black plastic peg on runner out.
See FIGURE A.
911
/

STEP 2.2
Hold the drawer with both of your hands. carefully lift the drawer front up from the front metal pin, then slide forward to
remove from back hooks. See FIGURE D.
Metal pin/
Hole for pin
STEP 2.3
Lock the drawer to the runner by pushing the black plastic peg on the runner in. See detail FIGURE E.
FIGURE D
FIGURE E
STEP 2: DRAWER ASSEMBLY INSTRUCTIONS
STEP 2.1
Pull the runner on the way out. Put the drawer onto them then hold both the runner with your hands. Lift the
drawer up with your thumbs and push to hook the drawer at end of the runner. See FIGURE C.
Metal hook
FIGURE C
10 11
/

STEP 3: DRAWER HEIGHT ADJUSTMENT INSTRUCTIONS
FIGURE F
Plastic button
STEP 3
Adjust around gap of drawer by turn plastic button clockwise/counterclock wise direction. See FIGURE F.
11 11
/