BECKMAN RECTANGULAR CHANDELIER 54"
IMPORTANT SAFETY INSTRUCTIONS
INSTALLATION BY A LICENSED ELECTRICIAN IS STRONGLY
RECOMMENDED.
This xture has been rated for up to six (6) 40-watt maximum Type T
lightbulbs or six (6) 13-watt compact uorescent lightbulbs. To avoid the
risk of re, do not exceed the recommended wattage.
WARNINGS
All wires are connected. When unpacking, be careful not to pull wires, as
a bad connection may result. Do not connect electricity until your fixture
is fully assembled. To reduce the risk of fire, electrical shock, or personal
injury, always turn off fixture and allow it to cool prior to replacing the
light bulb. Do not touch or look directly at the bulb when fixture is
illuminated. Keep flammable materials away from lit bulb.
WARNING: This product can expose you to lead, which is
known to the State of California to cause cancer and birth defects or
other reproductive harm. For more information, go to
www.P65Warnings.ca.gov.
THIS PRODUCT IS NOT A TOY AND HAS NO PLAY
VALUE.
WARNING: STRANGULATION HAZARD
Keep cord at least 3 feet away from cribs, bassinets, and toddler beds.
Keep out of reach of children under 3 years of age.
ASSEMBLY & INSTALLATION
SHUT OFF THE MAIN ELECTRICAL SUPPLY FROM THE FUSE
BOX OR CIRCUIT BREAKER PANEL.
1. Carefully remove all parts from the box and remove all plastic
coverings.
2. Remove Metal Tabs (Q) from Lantern Box (N) by removing Set
Screws (R). Remove“L” Metal Tabs (S) by removing Screws (T).
Install Small Glass Panels (O) and Large Glass Panels (P) to side of
Lantern Box (N), then secure with Metal Tabs (Q) and“L” Metal Tabs
(S). Tighten with Set Screws (O) and Screws (T).
3. Carefully slide Lantern Box (N) through Hanging Frame (M). Clip Top
Hooks (U) onto the top loops of Hanging Frame (M) found under
Joints (L). Make sure Top Hooks (U) are sitting in the middle of the
top loop of Hanging Frame (M).
4. Determine the hanging length of xture. Connect Hanging Frame
(M) to some or all Connection Rods (H) (J) (K) and Connective Tubes
(I) according to the height needed. Note: Pre-wire Connection Rods
(H) (J) (K) before putting them together.
5. Feed wires through Connection Rods (H) (J) (K), Hanging Loops (G),
Canopy Rings (E), Canopy (C) and Mounting Loops (B).
6. Thread Hanging Loops (F) onto the inner rod of the top Connection
Rods (H) (J) (K).
7. Unscrew Canopy Rings (E). Slide Canopy Rings (E) and Canopy (C)
onto Connection Rods (H) (J) (K).
8. Attach Mounting Plate (A) to the ceiling and secure with Mounting
Screws (D). If woodscrews and anchors will be used, proper
fasteners can be found from your local hardware store.
9. Connect the safety steel wire from the xture and the safety cable
from ceiling. (Refer to the illustration on previous page).
10. Gently pull the wiring from the ceiling outlet box and allow the wires
to hang. Thread the wires through the center hole in Mounting Plate
(A).
11. Carefully inspect the chandelier’s two xture wires. One has very
ne ridges molded into the plastic covering – this is the neutral wire.
The second wire’s covering is smooth – this is the hot wire. The bare
wire is the ground wire.
12. Connect the ground wire from the xture with the ground wire
(usually bare) from your ceiling box using a wire nut. If your house
does not have ground wire, then attach the ground wire from the
xture to the green grounding screw inside of the outlet box. IT
IS IMPERATIVE THAT THE OUTLET BOX IN YOUR HOME BE
PROPERLY GROUNDED.
13. Connect the neutral wire from your xture with the neutral wire
(usually white) from your ceiling box using a wire nut.
14. Connect the hot wire from your xture with the hot wire (usually
black) from your outlet box using a wire nut. DO NOT REVERSE
THE HOT AND NEUTRAL CONNECTIONS OTHERWISE SAFETY
WILL BE COMPROMISED.
15. Tuck the wire connection neatly into the ceiling outlet box.
16. Hook Hanging Loop (G) to Mounting Loops (B) by opening / closing
Quick Links (F). Raise Canopy (C) to cover the ceiling outlet box,
then secure with Canopy Rings (E) to Mounting Loops (B).
17. Insert Bulbs (V) into each of the sockets.
CARE INSTRUCTIONS
Do not use polishes or cleaners on the fixture. Wipe clean with a soft, dry
cloth.
ASSEMBLY & INSTALLATION CONT.
