Rheem RKKN-B073 Series User manual

INSTALLATION INSTRUCTIONS
Package Gas Electric Featuring
Industry Standard R-410A Refrigerant
RKKN-B073 (6 TON) SERIES
92-23577-157-00
(BASED ON92-23577-141-03)
ACCREDITED
ISO 9001:2008

2
I. TABLE OF CO TE TS
. Table of Contents ..................................................................................................2
. ntroduction ............................................................................................................3
. Checking Product Received ..................................................................................3
V. Specifications.........................................................................................................3
A. General .............................................................................................................3
B. Major Components............................................................................................3
C. R-410A Refrigerant ...........................................................................................3
1. Specifications of R-410A...............................................................................3
2. Quick Reference Guide for R-410A ..............................................................4
3. Evaporator Coil/TXV .....................................................................................4
4. Tools Required for nstalling and Servicing R-410A Models.........................4
V. Safety nformation..................................................................................................4
V . Unit Dimensions.....................................................................................................5
V . nstallation..............................................................................................................7
A. General .............................................................................................................7
1. Pre- nstallation Check ..................................................................................7
2. Location Considerations...............................................................................7
B. Outside nstallation............................................................................................8
C. Attaching Exhaust and Combustion Air nlet Hoods .........................................9
D. Cover Panel nstallation/Conversion Procedure ...............................................9
E. Clearances ........................................................................................................9
F. Rooftop nstallation ...........................................................................................9
G. Ductwork .........................................................................................................10
H. Return Air ........................................................................................................11
V . Gas Supply, Condensate Drain and Piping .........................................................13
A. Gas Connection ..............................................................................................13
B. LP Conversion.................................................................................................14
C. NOx Models ....................................................................................................14
D. Adjusting or Checking Furnace nput ..............................................................15
E. Condensate Drain ...........................................................................................17
X. Wiring...................................................................................................................17
A. Power Supply ..................................................................................................17
B. Hook Up ..........................................................................................................19
C. nternal Wiring .................................................................................................19
D. Thermostat ......................................................................................................19
X. Furnace Section Controls and gnition System....................................................20
Normal Furnace Operating Sequence.................................................................20
Operating nstructions .........................................................................................20
Burners ................................................................................................................21
Manual Reset Overtemperature Control..............................................................21
Pressure Switch...................................................................................................21
Limit Control ........................................................................................................22
X . System Operating nformation .............................................................................22
Advise the Customer ...........................................................................................22
Furnace Section Maintenance.............................................................................22
Lubrication ...........................................................................................................23
Cooling Section Maintenance..............................................................................23
Replacement Parts ..............................................................................................24
Troubleshooting...................................................................................................24
Wiring Diagrams ..................................................................................................24
Charging ..............................................................................................................24
X . General Data ..................................................................................................25-27
X . Miscellaneous ......................................................................................................28
Electrical Data .....................................................................................................28
Airflow Performance ............................................................................................29
Wiring Diagrams.............................................................................................30-32
Charge Chart .......................................................................................................33
Troubleshooting..............................................................................................34-36

3
II. I TRODUCTIO
This booklet contains the installation and operating instructions for your combination gas
heating/electric cooling unit. There are some precautions that should be taken to derive
maximum satisfaction from it. mproper installation can result in unsatisfactory operation
or dangerous conditions.
Read this booklet and any instructions packaged with separate equipment required to
make up the system prior to installation. Give this booklet to the owner and explain its
provisions. The owner should retain this booklet for future reference.
III. CHECKI G PRODUCT RECEIVED
Upon receiving the unit, inspect it for any damage from shipment. Claims for damage,
either shipping or concealed, should be filed immediately with the shipping company.
IMPORTANT: Check the unit model number, heating size, electrical characteristics, and
accessories to determine if they are correct.
IV. SPECIFICATIO S
A. GE ERAL
The Combination Gas Heating/Electric Cooling Rooftop is available in 100,000 and
135,000 BTU/Hr. heating inputs and cooling capacity of 6 nominal tons of cooling. Units
are convertible from bottom supply and return to side supply and return by relocation of
supply and return air access panels. See cover installation detail.
The units are weatherized for mounting outside of the building.
The information on the rating plate is in compliance with the FTC and DOE rating for sin-
gle phase units. The following information is for three phase units which are not covered
under the DOE certification program.
1. The energy consumption of the ignition system used with this unit is 9 watts.
2. The efficiency rating of this unit is a product thermal efficiency rating determined
under continuous operating conditions independent of any installed system.
B. MAJOR COMPO E TS
The unit includes a hermetically-sealed refrigerating system (consisting of a scroll com-
pressor, condenser coil, evaporator coil with thermostatic expansion valve), a circulation
air blower, a condenser fan, a heat exchanger assembly, gas burner and control assem-
bly, combustion air motor and fan, and all necessary internal electrical wiring. The cool-
ing system of these units is factory-evacuated, charged with R-410A refrigerant and per-
formance tested. Refrigerant amount and type are indicated on rating plate.
C. R-410A REFRIGERA T
All units are factory charged with R-410A refrigerant.
1. Specification of R-410A:
Application: R-410A is not a drop-in replacement for R-22; equipment designs must
accommodate its higher pressures. t cannot be retrofitted into R-22 units.
Pressure: The pressure of R-410A is approximately 60% (1.6 times) greater than R-
22. Recovery and recycle equipment, pumps, hoses and the like need to have design
pressure ratings appropriate for R-410A. Manifold sets need to range up to 800 psig
high-side and 250 psig low-side with a 550 psig low-side retard. Hoses need to have a
service pressure rating of 800 psig. Recovery cylinders need to have a 400 psig service
pressure rating. DOT 4BA400 or DOT BW400.
Combustibility: At pressures above 1 atmosphere, mixture of R-410A and air can
become combustible. R-410A and air should never be mixed in tanks or supply
!WAR I G
T E MANUFACTURER’S WARRAN-
TY DOES NOT COVER ANY DAM-
AGE OR DEFECT TO T E AIR CON-
DITIONER CAUSED BY T E
ATTAC MENT OR USE OF ANY
COMPONENTS, ACCESSORIES OR
DEVICES (OT ER T AN T OSE
AUT ORIZED BY T E MANUFAC-
TURER) INTO, ONTO OR IN CON-
JUNCTION WIT T E AIR CONDI-
TIONER. YOU S OULD BE AWARE
T AT T E USE OF UNAUT O-
RIZED COMPONENTS, ACCES-
SORIES OR DEVICES MAY
ADVERSELY AFFECT T E OPERA-
TION OF T E AIR CONDITIONER
AND MAY ALSO ENDANGER LIFE
AND PROPERTY. T E MANUFAC-
TURER DISCLAIMS ANY RESPON-
SIBILITY FOR SUC LOSS OR
INJURY RESULTING FROM T E
USE OF SUC UNAUT ORIZED
COMPONENTS, ACCESSORIES OR
DEVICES.
!WAR I G
UNITS ARE NOT DESIGN CERTIFIED TO BE INSTALLED INSIDE T E STRUC-
TURE. DOING SO CAN CAUSE INADEQUATE UNIT PERFORMANCE AS WELL
AS PROPERTY DAMAGE AND CARBON MONOXIDE POISONING RESULTING
IN PERSONAL INJURY OR DEAT .
Recognize this symbol as an indi-
cation of mportant Safety
nformation!
!
!WAR I G
INSTALL T IS UNIT ONLY IN A
LOCATION AND POSITION AS
SPECIFIED IN T E LOCATION
REQUIREMENTS AND CONSIDERA-
TIONS SECTION OF T ESE
INSTRUCTIONS. PROVIDE ADE-
QUATE COMBUSTION AND VENTI-
LATION AIR TO T E UNIT SPACE
AS SPECIFIED IN T E VENTING
SECTION OF T ESE INSTRUC-
TIONS.
!WAR I G
PROVIDE ADEQUATE COMBUS-
TION AND VENTILATION AIR TO
T E UNIT SPACE AS SPECIFIED IN
T E COMBUSTION AND VENTILA-
TION AIR SECTION OF T ESE
INSTRUCTIONS.
!WARNING
EFFICIE CY TESTI G OTICE
FOR PURPOSES OF VERIFYI G OR TESTI G
EFFICIE CY RATI GS, THE TEST PROCEDURE
I TITLE 10 PART 431 APPE DIX A TO
SUBPART F (U IFORM TEST METHOD FOR
MEASURI G THE E ERGY CO SUMPTIO OF
SMALL LARGE A D VERY LARGE
COMMERCIAL PACKAGE AIR CO DITIO I G
A D HEATI G EQUIPME T), TITLE 10 PART
431.76 SUBPART D (U IFORM TEST METHOD
FOR MEASURI G E ERGY CO SUMPTIO OF
COMMERCIAL WARM AIR FUR ACES), A D
THE CLARIFYI G PROVISIO S PROVIDED I
THE AHRI OPERATIO S MA UALS FOR
U ITARY LARGE EQUIPME T 340/360, 365
A D COMMERCIAL FUR ACES THAT WERE
APPLICABLE AT THE DATE OF MA UFACTURE
SHOULD BE USED FOR TEST SET UP A D PER-
FORMA CE.

4
lines, or be allowed to accumulate in storage tanks. Leak checking should never
be done with a mixture of R-410A and air. Leak checking can be performed safely
with nitrogen or a mixture of R-410A and nitrogen.
2. Quick Reference Guide For R-410A
• R-410A refrigerant operates at approximately 60% higher pressure (1.6 times) than R-
22. Ensure that servicing equipment is designed to operate with R-410A.
• R-410A refrigerant cylinders are pink.
• R-410A, as with other HFC’s is only compatible with POEoils.
• Vacuum pumps will not remove moisture from POE oil.
• R-410A systems are to be charged with liquid refrigerants. Prior to March 1999, R-
410A refrigerant cylinders had a dip tube. These cylinders should be kept upright for
equipment charging. Post March 1999 cylinders do not have a dip tube and should
be inverted to ensure liquid charging of the equipment.
• Do not install a suction line filter drier in the liquid line.
• A liquid line filter drier is standard on every unit.
• Desiccant (drying agent) must be compatible for POE oils and R-410A
3. Evaporator Coil / TXV
The thermostatic expansion valve is specifically designed to operate with R-410A. DO
NOT use an R-22 TXV. The existing evaporator must be replaced with the factory
specified TXV evaporator specifically designed for R-410A.
4. Tools Required For Installing & Servicing R-410A Models
Manifold Sets:
-Up to 800 PS G High side
-Up to 250 PS G Low Side
-550 PS G Low Side Retard
Manifold Hoses:
-Service Pressure Rating of 800 PS G
Recovery Cylinders:
-400 PS G Pressure Rating
-Dept. of Transportation 4BA400 or BW400
V. SAFETY I FORMATIO
!
CAUTIO
R-410A systems operate at higher pressures than R-22 systems. Do not use
R-22 service equipment or components on R-410A equipment.
!WAR I G
USE ONLY WIT TYPE OF GAS APPROVED FOR T IS UNIT. REFER TO T E
UNIT RATING PLATE.

5
2-5/32
[55]
4-5/8
[118]
26
[660]
4.502
[114]
13-1/8
[333]
4-1/2
[114]
13-1/8
[333]
77-15/32
[1968]
20
[508]
2-3/8
[60]
43-7/32
[1098]
2-3/8
[60]
2-3/8
[60]
RETURN
AIR SUPPLY
AIR
[ ] DESIGNATES METRIC CONVERSIONS
TOP VIEW
ST-A1143
FIGURE 2
VI. U IT DIME SIO S
RKKN 6 TON [21.1 kW] MODELS
FIGURE 1
ST-A1224-01
OUTDOOR FAN
OUTDOOR
CO L

6
FIGURE 3
ST-A1148
ST-A1224
BACK VIEW
FRONT VIEW
FIGURE 5
ST-A1224
SIDE
VIEW
FIGURE 4

7
VII. I STALLATIO
A. GE ERAL
nstall this unit in accordance with The American National Standard Z223.1-latest edition
booklet entitled “National Fuel Gas Code,” and the requirements or codes of the local
utility or other authority having jurisdiction.
Additional helpful publications available from the “National Fire Protection Association”
are: NFPA-90A - nstallation of Air Conditioning and Ventilating Systems 1985 or latest
edition. NFPA-90B - Warm Air Heating and Air Conditioning Systems 1984.
These publications are available from:
National Fire Protection Association, nc.
1 Batterymarch Park
Quincy, MA 02169-7471
www.nfpa.org
1. PRE- NSTALLAT ON CHECK-PO NTS — Before attempting any installation, care-
fully consider the following points:
Structural strength of supporting members
(Rooftop nstallation)
Clearances and provision for servicing
Power supply and wiring
Gas supply and piping
Air duct connections and sizing
Drain facilities and connections
Location for minimum noise and
vibration - away from bedroom
windows
2. LOCAT ON CONS DERAT ONS
The metal parts of this unit may be subject to rust or deterioration in adverse envi-
ronmental conditions. This oxidation could shorten the equipment’s useful life. Salt
spray, fog or mist in seacoast areas, sulphur or chlorine from lawn watering systems,
and various chemical contaminants from industries such as paper mills and petrole-
um refineries are especially corrosive.
If the unit is to be installed in an area where contaminants are likely to be a
problem, give special attention to the equipment location and exposure.
1. Avoid having lawn sprinkler heads spray directly on the unit cabinet.
2. n coastal areas locate the unit on the side of the building away from the water-
front.
3. Shielding by a fence or shrubs may give some protection.
1. Frequent washing of the cabinet, fan blade and coil with fresh water will remove
most of the salt or other contaminants that build up on the unit.
2. Regular cleaning and waxing of the cabinet with a good automobile polish will pro-
vide some protection.
3. A good liquid cleaner may be used several times a year to remove matter that will
not wash off with water.
Several different types of protective coatings are offered in some areas. These coatings
may provide some benefit, but the effectiveness of such coating materials cannot be
verified by the equipment manufacturer.
The best protection is frequent cleaning, maintenance and minimal exposure to
contaminants.
!WAR I G
ALWAYS INSTALL UNIT TO OPER-
ATE WIT IN T E UNIT'S INTENDED
TEMPERATURE-RISE RANGE WIT
A DUCT SYSTEM W IC AS AN
EXTERNAL STATIC PRESSURE
WIT IN T E ALLOWABLE RANGE,
AS SPECIFIED IN DUCTING SEC-
TION OF T ESE INSTRUCTIONS.
SEE ALSO UNIT RATING PLATE.
!WAR I G
W EN A UNIT IS INSTALLED SO
T AT SUPPLY DUCTS CARRY AIR
CIRCULATED BY T E UNIT TO
AREAS OUTSIDE T E SPACE CON-
TAINING T E UNIT, T E RETURN
AIR S ALL ALSO BE ANDLED BY
DUCT(S) SEALED TO T E UNIT
CASING AND TERMINATING OUT-
SIDE T E SPACE CONTAINING
T E UNIT.
!WAR I G
NEVER TEST FOR GAS LEAKS
WIT AN OPEN FLAME. USE A
COMMERCIALLY AVAILABLE
SOAP SOLUTION MADE SPECIFI-
CALLY FOR T E DETECTION OF
LEAKS TO C ECK ALL CONNEC-
TIONS, AS SPECIFIED IN GAS
SUPPLY AND PIPING SECTION OF
T ESE INSTRUCTIONS.
!WAR I G
DISCONNECT ALL POWER TO UNIT BEFORE STARTING MAINTENANCE.
FAILURE TO DO SO CAN CAUSE ELECTRICAL S OCK RESULT ING IN PER-
SONAL INJURY OR DEAT . REGULAR MAINTENANCE WILL REDUCE T E
BUILDUP OF CONTAMINANTS AND ELP TO PROTECT T E UNIT’S FINIS .

8
B. OUTSIDE SLAB I STALLATIO
(Typical outdoor slab installation is shown in Figure 6.)
1. Select a location where external water drainage cannot collect around unit.
2. Provide a level slab sufficiently high enough above grade to prevent surface water
from entering the unit
3. The location of the unit should be such as to provide proper access for inspection
and servicing as shown in Figure 8.
4. Locate unit where operating sounds will not disturb owner or neighbors.
5. Locate unit so roof runoff water does not pour directly on the unit. Provide gutter or
other shielding at roof level. Do not locate unit in an area where excessive snow
drifting may occur or accumulate.
6. Where snowfall is anticipated, the height of the unit above the ground level must be
considered. Mount unit high enough to be above anticipated maximum area snowfall
and to allow combustion air to enter the combustion air inlet.
7. Select an area which will keep the areas of the vent, air intake, and A/C condenser
fins free and clear of obstructions such as weeds, shrubs, vines, snow, etc. nform
the user accordingly.
8. Remove compressor shipping supports (if so equipped) after installation.
!WAR I G
T IS UNIT MAY BE USED TO EAT
TE BUILDING OR STRUCTURE
DURING CONSTRUCTION IF T E
FOLLOWING INSTALLATION
REQUIREMENTS ARE MET.
INSTALLATION MUST COMPLY
WIT ALL INSTALLATION
INSTRUCTIONS INCLUDING:
• PROPER VENT INSTALLATION;
• FURNACE OPERATING UNDER
T ERMOSTATIC CONTROL;
• RETURN AIR DUCT SEALED TO
T E FURNACE;
• AIR FILTERS IN PLACE;
• SET FURNACE INPUT RATE AND
TEMPERATURE RISE PER RAT-
ING PLATE MARKING;
• MEANS OF PROVIDING OUT-
DOOR AIR REQUIRED FOR COM-
BUSTION;
• RETURN AIR TEMPERATURE
MAINTAINED BETWEEN 55°F
(13°C) AND 80°F (27°C); AND
• INSTALLATION OF EX AUST
AND COMBUSTION AIR INLET
OODS COMPLETED;
• CLEAN FURNACE, DUCT WORK
AND COMPONENTS UPON SUB-
STANTIAL COMPLETION OF T E
CONSTRUCTION PROCESS, AND
VERIFY FURNACE OPERATING
CONDITIONS INCLUDING IGNI-
TION, INPUT RATE, TEMPERA-
TURE RISE AND VENTING,
ACCORDING TO T E INSTRUC-
TIONS.
!WAR I G
T ESE UNITS ARE DESIGNED CERTIFIED FOR OUTDOOR INSTALLATION
ONLY. INSTALLATION INSIDE ANY PART OF A STRUCTURE CAN RESULT IN
INADEQUATE UNIT PERFORMANCE AS WELL AS PROPERTY DAMAGE.
INSTALLATION INSIDE CAN ALSO CAUSE RECIRCULATION OF FLUE PROD-
UCTS INTO T E CONDITIONED SPACE RESULTING IN PERSONAL INJURY
OR DEAT .
FIGURE 6
OUTSIDE SLAB INSTALLATION. CLOSET DISTRIBUTION SYSTEM. SLAB FLOOR CONSTRUCTION.
SR-A1224

9
C. ATTACHI G EXHAUST A D COMBUSTIO AIR I LET HOODS
IMPORTANT: Do not operate this unit without the exhaust/combustion air inlet hood
properly installed. This hood is shipped in a carton in the blower compartment inside
the unit and must be attached when the unit is installed. See Figure 3.
To attach exhaust/combustion air inlet hood:
1. Remove screws securing blower access panel and remove access panel. For location of
blower access panel, see Figure 2.
2. Remove exhaust/combustion air inlet hood from the carton, located inside the blower
compartment.
3. Attach blower access panel.
4. Attach the combustion air inlet/exhaust hood with screws. Reference Figure 3 for proper
location. Screws are in carton with the hood.
5. Vent the unit using the flue exhaust hood, as supplied from the factory, without alteration
or addition.
D. COVER PA EL I STALLATIO /CO VERSIO PROCEDURE
DOWNFLOW TO HOR ZONTAL
1. Remove the screws and covers from the outside of the supply and return sections.
2. nstall the covers in the bottom supply and return openings with the painted side up.
See Figure 7. Use the existing gasket to seal the covers.
3. Secure the supply cover to the base of the unit with 1 screw, engaging prepunched
tab in unit base.
4. Secure the return cover to the base of the unit with screws engaging prepunched
holes in the unit base.
E. CLEARA CES
The following minimum clearances must be observed for proper unit performance and
serviceability. Reference Figure 8.
NOTE: Supply duct may be installed with “0’ inch clearance to combustible materials,
provided 1(minimum Fiberglass insulation is applied either inside or on the outside of
the duct.
F. ROOFTOP I STALLATIO
1. Before locating the unit on the roof, make sure that the roof structure is adequate to
support the weight involved. (See Electrical & Physical Tables in this manual.) TH S
S VERY MPORTANT AND THE NSTALLER’S RESPONS B L TY.
2. For rigging and roofcurb details, see Figures 9, 10, 11 and 12.
3. The location of the unit on the roof should be such as to provide proper access for
inspection and servicing.
4. Remove compressor shipping supports (if so equipped) after installation.
IMPORTANT: If unit will not be put into service immediately, block off supply and return
air openings to prevent excessive condensation.

10
G. DUCTWORK
The installing contractor should fabricate ductwork in accordance with local codes. Use
industry manuals as a guide when sizing and designing the duct system. Contact Air
Conditioning Contractors of America, 2800 Shirlington Road, Suite 300, Arlington, VA
22206, http://www.acca.org.
36“
60“
48“
VERTICAL
CLEARANCE
18“
12“
FIGURE 8
CLEARANCES
ST-1224
FIGURE 7
COVER GASKET DETAIL FOR UNITS S IPPED FOR DOWNFLOW APPLICATION
BEING CONVERTED TO ORIZONTAL
631
Recommended
Clearance Location
48( A - Front
18( B - Condenser Coil
12(* C - Duct Side
36( D - Evaporator End
60( E - Above
*Without Economizer. 57 With Economizer

11
Place the unit as close to the conditioned space as possible allowing clearances as indi-
cated. Run ducts as directly as possible to supply and return outlets. Use of non-flam-
mable weatherproof flexible connectors on both supply and return connections at unit to
reduce noise transmission is recommended.
On ductwork exposed to outside temperature and humidity, use a minimum of 2(of
insulation and a vapor barrier. Distribution system in attic, furred space or crawl space
should be insulated with at least 2(of insulation. 1⁄2(to 1(thick insulation is usually suffi-
cient for ductwork inside the air conditioned space.
Provide balancing dampers for each branch duct in the supply system. Properly support
ductwork from the structure.
IMPORTANT: n the event that the return air ducts must be run through an “unconfined”
space containing other fuel burning equipment, it is imperative that the user/homeowner
must be informed against future changes in construction which might change this to a
“confined space.” Also, caution the user/homeowner against any future installation of
additional equipment (such as power ventilators, clothes dryers, etc., within the existing
unconfined and/or confined space which might create a negative pressure within the
vicinity of other solid, liquid, or gas fueled appliances.
H. RETUR AIR
FIGURE 9
FLAT ROOFTOP INSTALLATION, ATTIC OR DROP CEILING DISTRIBUTING SYSTEM. MOUNTED ON
ROOFCURB. CURB MUST BE LEVEL.
ST-1224
!WAR I G
NEVER ALLOW PRODUCTS OF COMBUSTION OR T E FLUE PRODUCTS TO
ENTER T E RETURN AIR DUCTWORK, OR T E CIRCULATING AIR SUPPLY.
ALL RETURN DUCTWORK MUST BE ADEQUATELY SEALED AND SECURED
TO T E FURNACE WIT S EET METAL SCREWS, AND JOINTS TAPED. ALL
OT ER DUCT JOINTS MUST BE SECURED WIT APPROVED CONNECTIONS
AND SEALED AIRTIG T.
FAILURE TO PREVENT PRODUCTS OF COMBUSTION FROM BEING CIRCU-
LATED INTO T E LIVING SPACE CAN CREATE POTENTIALLY AZARDOUS
CONDITIONS, INCLUDING CARBON MONOXIDE POISONING T AT COULD
RESULT IN PERSONAL INJURY OR DEAT .
!WAR I G
DO NOT, UNDER ANY CIRCUMSTANCES, CONNECT RETURN DUCTWORK TO
ANY OT ER EAT PRODUCING DEVICE SUC AS FIREPLACE INSERT,
STOVE, ETC. UNAUT ORIZED USE OF SUC DEVICES MAY RESULT IN FIRE,
CARBON MONOXIDE POISONING, EXPLOSION, PERSONAL INJURY, PROP-
ERTY DAMAGE OR DEAT .

12
ROOFTOP UNI
COUNTER FLA
GASKET
NAILER STRIP
DUCT*
ROOFCURB
INSULATION*
CANT STRIP*
ROOF FE
INSULATI
ROOF DE
TURAL
ER*
FIGURE 12
ROOFCURB
FIGURE 11
ROOFCURB
RETURN DUCT*
SUPPLY DUCT*
NAILING STRIP
INSULATION PANELS
(2) SUPPLIED
GASKET
(FULL PERIMETER
AND ON DIVIDERS,
MUST BE ABOVE DUCT
AND INSULATION
PANEL FLANGES.)
HOLD
DOWN
BRACKET
TYP. (4) PLCS.
UNIT
296
ST-A0801-19-01
CORNER WEIG TS BY PERCENTAGE
A B C D
22% 27% 23% 28%
SPREADER BAR
A
B
D
C
L FT NG BEAM
CABLE OR CHA N
5/8(SHACKLE
(EACH CORNER)
38.25
25.75
C.G.
ST-A0801-19-01
ROOFTOP UN T
COUNTER FLASH NG*
NSULAT ON*
CANT STR P*
ROOF FELT*
NSULAT ON*
ROOF DECK*
*BY CONTRACTOR
ROOF
STRUCTURAL
MEMBER*
ROOFCURB
DUCT*
NA LER STR P
GASKET
RETURN
SUPPLY
FIGURE 10
LIFTING DETAIL

13
VIII.GAS SUPPLY, CO DE SATE DRAI A D
VIII.PIPI G
A. GAS CO ECTIO
IMPORTANT: Connect this unit only to gas supplied by a commercial utility.
1. nstall gas piping in accordance with local codes and regulations of the local utility
company. n the absence of local codes, the installation must conform to the specifi-
cations of the National Fuel Gas Code, ANS Z223.1 - latest edition.
NOTE: The use of flexible gas connectors is not recommended. f local codes allow
the use of a corrugated stainless steel flexible gas appliance connector, always use
a new listed connector. Do not use a connector which has previously serviced anoth-
er gas appliance.
NOTE: The Commonwealth of Massachusetts requires the gas shut-off valve to be a
T-handle gas cock.
2. Connect the gas line to the gas pipe inlet opening provided into the 1/2(inlet valve.
See Figure 6 or 9 for typical piping.
3. Size the gas line to the furnace adequately to prevent undue pressure drop and
never less than 1/2(nominal pipe size.
4. nstall a drip leg or sediment trap in the gas supply line as close to the unit as possible.
5. nstall an outside ground joint union to connect the gas supply to the control assem-
bly at the burner tray.
6. Gas valves have been factory installed. nstall a manual gas valve where local codes
specify a shut-off valve outside the unit casing. (See Figure 13.)
7. Make sure piping is tight. A pipe compound resistant to the action of liquefied
petroleum gases must be used at all threaded pipe connections.
8. IMPORTANT: Any additions, changes or conversions required for the furnace to
satisfactorily meet the application should be made by a qualified installer, service
agency or the gas supplier, using factory-specified or approved parts. In the com-
monwealth of Massachusetts, installation must be performed by a licensed plumber
or gas fitter for appropriate fuel.
IMPORTANT: Disconnect the furnace and its individual shutoff valve from the gas sup-
ply piping during any pressure testing of that system at test pressures in excess of 1/2
pound per square inch gauge or isolate the system from the gas supply piping system
by closing its individual manual shutoff valve during any pressure testing of this gas sup-
ply system at pressures equal to or less than 1/2 PSIG.
TO CHECK FOR GAS LEAKS, USE A SOAP AND WATER SOLUT ON OR OTHER
APPROVED METHOD. DO NOT USE AN OPEN FLAME.
IMPORTANT: Check the rating plate to make certain the appliance is equipped to burn
the type of gas supplied. Care should be taken after installation of this equipment that
the gas control valve not be subjected to high gas supply line pressure.
FIGURE 13
SUGGESTED GAS PIPING
FROM GAS
METER
*Factory supplied grommet must be utilized.
MANUAL GAS
SHUT-OFF
VALVE
UN T GAS SUPPLY
CONNECT ON *
ROOF OR GROUND LEVEL INSTALLATION
!WAR I G
C ECK FOR LEAKS. T E USE OF AN OPEN FLAME CAN RESULT IN FIRE,
EXPLOSION, PROPERTY DAMAGE, PERSONAL INJURY OR DEAT .
Nominal
ron Pipe
Size,
nches
Equivalent Length of Pipe, Feet
10 20 30 40 50 60 70 80
1⁄2 132 92 73 63 56 50 46 43
3⁄4 278 190 152 130 115 105 96 90
1 520 350 285 245 215 195 180 170
11⁄4 1,050 730 590 500 440 400 370 350
11⁄2 1,600 1,100 890 760 670 610 560 530
TABLE 1
NATURAL GAS PIPE CAPACITY TABLE (CU. FT./ R.)

14
n making gas connections, avoid strains as they may cause noise and damage the con-
trols. Use a backup wrench on the valve to avoid damage.
The capacities of gas pipe of different diameters and lengths in cu. ft. per hr. with pres-
sure drop of 0.3 in. and specific gravity of 0.60 (natural gas) are shown in Table 1.
After determining the pipe length, select the pipe size which will provide the minimum
cubic feet per hour re quired for the gas input rating of the furnace. By formula:
Gas Input of Furnace
(BTU/HR)
Cu. Ft. Per Hr. Required = Heating Value of Gas
(BTU/FT3)
The gas input of the furnace is marked on the furnace rating plate. The heating value of
the gas (BTU/FT3) may be determined by consulting the local natural gas utility or the
L.P. gas supplier.
B. LP CO VERSIO
Convert the valve to use liquefied petroleum (LP) gas by replacing the pressure regula-
tor spring with the conversion kit spring. This LP kit spring allows the regulator to main-
tain the proper manifold pressure for LP gas. The correct burner LP orifices are included
in the kit. See Figure 14.
IMPORTANT: To remove the gas valve, remove the four screws securing the manifold pipe
to the burner tray. Remove the manifold pipe with gas valve attached. See Figure 15.
NOTE: Order the correct LP conversion kit from the furnace manufacturer. See
Conversion Kit Index shipped with unit for proper LP kit number. Furnace conver-
sion to LP gas must be performed by a ualified technician.
C. Ox MODELS
When converting units equipped with NOx inserts to LP gas, the stainless steel screen
mesh inserts in the entrance of the tubular exchangers are not required to meet
SCAQMD NOx emission levels. These inserts and 1/8(diameter retaining rod should be
carefully removed before firing this furnace on LP gas. IMPORTANT: This furnace is not
designed to operate on LP gas with the NOx inserts in place.
Step by step instructions on removing the NOx inserts and retaining rod are included in
the Conversion Kit nstallation nstructions.
!WAR I G
FACTORY FOR USE ON NATURAL GAS ONLY. CONVERSION TO LP GAS
REQUIRES A SPECIAL KIT SUPPLIED BY T E DISTRIBUTOR OR MANUFACTUR-
ER. MAILING ADDRESSES ARE LISTED ON T E FURNACE RATING PLATE,
PARTS LIST AND WARRANTY. FAILURE TO USE T E PROPER CONVERSION
KIT CAN CAUSE FIRE, CARBON MONOXIDE POISONING, EXPLOSION, PERSON-
AL INJURY, PROPERTY DAMAGE OR DEAT .
Maximum capacity of pipe in thousands of BTU per hour of undiluted liquefied petroleum gases
(at 11 inches water column inlet pressure).
(Based on a Pressure Drop of 0.5 Inch Water Column)
TABLE 2
LP GAS PIPE CAPACITY TABLE (CU. FT./ R.)
ominal
Iron Pipe
Size, Inches 10 20 30 40 50 60 70 80 90 100 125 150
275 189 152 129 114 103 96 89 83 78 69 63
567 393 315 267 237 217 196 182 173 162 146 132
1,071 732 590 504 448 409 378 346 322 307 275 252
2,205 1,496 1,212 1,039 913 834 771 724 677 630 567 511
3,307 2,299 1,858 1,559 1,417 1,275 1,181 1,086 1,023 976 866 787
6,221 4,331 3,465 2,992 2,646 2,394 2,205 2,047 1,921 1,811 1,606 1,496
1/2
3/4
1
1-1/4
1-1/2
2
Length of Pipe, Feet
Example (LP): Input BTU requirement of unit, 150,000
Equivalent length of pipe, 60 ft. = 3/4(IPS required.

15
D. ADJUSTI G OR CHECKI G FUR ACE I PUT
– Natural Gas Line Pressure 5(- 10.5(W.C.
– LP Gas Line Pressure 11(- 13(W.C.
– Natural Gas Manifold Pressure 3.5( W.C
– LP Gas Manifold Pressure - 10(W.C.
Supply and manifold pressure taps are located on the gas valve body 1/8(N.P.T. and
on the manifold.
Use a properly calibrated manometer gauge for accurate gas pressure readings.
Only small variations in the gas flow should be made by means of the pressure regulator
adjustment. Furnaces functioning on LP gas must be set by means of the tank or branch
supply regulators. The furnace manifold pressure should be set at 10(W.C. at the gas
control valve.
To adjust the pressure regulator, remove the regulator cap and turn the adjustment
screw clockwise to increase pressure or counterclockwise to decrease pressure. Then
replace the regulator cap securely.
Any necessary major changes in the gas flow rate should be made by changing the size
of the burner orifices. To change orifice spuds, shut off the manual main gas valve and
remove the gas manifold.
For elevations up to 2,000 feet, rating plate input ratings apply. For high altitudes (eleva-
tions over 2,000 ft.), see conversion kit index 92-21519-XX for derating and orifice spud
sizes.
Check of input is important to prevent over-firing of the furnace beyond its
design-rated input. NEVER SET NPUT ABOVE THAT SHOWN ON THE RAT NG
PLATE. Use the following table or formula to determine input rate.
Heating Value of Gas
(BTU/Cu. Ft.) × 3600
Cu. Ft. Per Hr. Required = Time in Seconds
(for 1 Cu. Ft.) of Gas
Start the furnace and measure the time required to burn one cubic foot of gas. Prior to
checking the furnace input, make certain that all other gas appliances are shut off, with
the exception of pilot burners. Time the meter with only the furnace in operation.
MPORTANT NOTE FOR ALT TUDES ABOVE 2,000 FEET (610 METERS): The main
burner orifices in your furnace and in these kits are sized for the nameplate input and
intended for installations at elevations up to 2,000 feet in the USA or Canada, or for ele-
vations of 2,000 - 4,500 feet (610 -1,373 meters) in Canada if the unit has been derated
at the factory. For elevations above 2,000 feet (610 meters) N THE USA ONLY (see
ANS -Z223.1), the burner orifices must be sized to reduce the input 4% for each 1,000
feet (305 meters) above sea level.
FIGURE 14
FIGURE 15
MAN FOLD P PE

16
Alternate Method for Canadian igh-Altitude Derate for Residential and Light
Commercial Gas/Electric Package Units
n Canada, unless an orifice change is specifically mandated by local codes, an alter-
nate method of altitude deration through a reduction in manifold pressure is acceptable
as described in Table 4.
The information in Table 1 is based on a heating value of 1000 BTU per cubic feet of
natural gas, and 2500 BTU per cubic feet of LP gas.
Important: Actual input rates must be measured on-site with manifold pressure
adjustment to ensure that an actual 10% reduction in input rate is achieved.
Once this field adjustment has been made, the label shown in Figure 17 must be affixed
in a conspicuous location on the front of the furnace cabinet.
NOTE: This label is supplied in the information package shipped with each unit.
ONE 1 21 1 30 1 34 1 39 3 45
40,000 TEN 13 30 15 0 15 36 16 30 37 30
ONE 0 54 1 0 1 3 1 6 2 30
60,000 TEN 9 0 10 0 10 24 11 0 25 0
ONE 0 41 0 45 0 47 0 50 1 53
80,000 TEN 6 45 7 30 7 48 8 15 18 45
ONE 0 33 0 36 0 38 0 40 1 30
100,000 TEN 5 24 6 0 6 15 6 36 15 0
METER TIME I MI UTES A D SECO DS FOR ORMAL
I PUT RATI G OF FUR ACES EQUIPPED FOR ATURAL
OR LP GAS
I PUT
BTU/HR
METER
SIZE
CU. FT.
HEATI G VALUE OF GAS BTU PER CU. FT.
900 1000 1040 1100 2500
MI . SEC. MI . SEC. MI . SEC. MI . SEC. MI . SEC.
TABLE 3
FIGURE 16
CONDENSATE DRAIN
DO NOT OVERTIG TEN DRAIN FITTING
Altitude
40,000 32,000
60,000 48,000
80,000 64,000 #45
0’-2000’ 100,000 80,000 3.5” W.C.
120,000 96,000
135,000 108,000 #43
36,000 28,800
54,000 43,200
2001’- 72,000 57,600 #45
4500’ 90,000 72,000 2.9” W.C.
108,000 86,400
121,500 97,200 #43
Input Output Orifice
Size
Manifold
Pressure
TABLE 4
ALTERNATE MET OD FOR CANADIAN IG -ALTITUDE DERATE
NATURAL GAS
Altitude
40,000 32,000
60,000 48,000
80,000 64,000 #55
0’-2000’ 100,000 80,000 10” W.C.
120,000 96,000
135,000 108,000
36,000 28,800
54,000 43,200
2001’- 72,000 57,600 #55
4500’ 90,000 72,000 8.1” W.C.
108,000 86,400
121,500 97,200
Input Output Orifice
Size
Manifold
Pressure
LP GAS
FIGURE 17
MANIFOLD PRESSURE C ANGE LABEL
The manifold pressure of this appliance has
been field adjusted to obtain the correct input
rating for installation at altitudes between
2,000 feet and 4,500 feet elevation.
La pression du distributeur d’alimentation de cet
appareil a ete ajuste sur les lieux afin d’obtenir la
bonne puissance d’entrée pour une installation
entre 2000 et 4500 pieds d’altitude.

17
E. CO DE SATE DRAI
The condensate drain connection of the evaporator is threaded 3/4(nominal P.V.C.
pipe. IMPORTANT: Install a condensate trap to ensure proper condensate drainage.
See Figure 16.
IX. WIRI G
A. POWER SUPPLY
1. All wiring should be made in accordance with the National Electrical Code.
Consult the local power company to determine the availability of sufficient power to
operate the unit. Check the voltage at power supply to make sure it corresponds to
the unit’s RATED VOLTAGE REQU REMENT. nstall a branch circuit disconnect
near the rooftop, in accordance with the N.E.C., C.E.C. or local codes. A bracket is
provided with the unit for mounting of the disconnect. See Figure 17.
2. t is important that proper electrical power is available at the unit. Voltage should not
vary more than 10% from that stamped on the unit nameplate. On three phase units,
phases must be balanced within 3%.
3. For branch circuit wiring (main power supply to unit disconnect), the minimum wire
size for the length of run can be determined from Table 3 using the circuit ampacity
found on the unit rating plate. Use the smallest wire size allowable in Table 4 from
the unit disconnect to unit.
GAS SUPPLY
FIGURE 18
RECOMMENDED BRANCH C RCU T D SCONNECT LOCAT ON
ST-1224
AWG Copper AWG Aluminum Connector Type and Size
Wire Size Wire Size (or equivalent)
#12 #10 T & B Wire Nut PT2
#10 # 8 T & B Wire Nut PT3
# 8 # 6 Sherman Split Bolt TSP6
# 6 # 4 Sherman Split Bolt TSP4
# 4 # 2 Sherman Split Bolt TSP2
TABLE 6
200 6 4 4 4 3 3 2 2
150 8 6 6 4 4 4 3 3
100 10 8 8 6 6 6 4 4
50 14 12 10 10 8 8 6 6
15 20 25 30 35 40 45 50
BRANC CIRCUIT AMPACITY
SUPPLY WIRE
LENGT -FEET
*Taken from National Electric Code
TABLE 5
BRANC CIRCUIT COPPER WIRE SIZE
(Based on 1% Voltage Drop)*
!WAR I G
TURN OFF T E MAIN ELECTRICAL POWER AT T E BRANC CIRCUIT DIS-
CONNECT CLOSEST TO T E UNIT BEFORE ATTEMPTING ANY WIRING. FAIL-
URE TO DO SO CAN CAUSE ELECTRICAL S OCK RESULTING IN PERSONAL
INJURY OR DEAT .

18
NOTE: A bracket is provided with the unit for mounting the branch circuit disconnect
to the unit. This is the recommended location for the disconnect. See Figure 17.
4. For through the base wiring entry reference Figure 18. All fittings and conduit are
field supplied for this application. Reference the chart with Figure 18 for proper hole
and conduit size.
NOTES:
1. Wire size based on 60°C rated wire insulation and 30°C Ambient Temp. (86°F).
2. For more than 3 conductors in a raceway or cable, see the N.E.C. for derating the
ampacity of each conductor.
When installed, the unit must be electrically grounded in accordance with local
codes or, in the absence of local codes, with the National Electrical Code,
ANSI/NFPA 70, if an external electrical source is utilized.
IMPORTANT: THIS UNIT IS AP PROVED FOR USE ITH COPPER CONDUCTORS
ONLY CONNECTED TO UNIT CONTACTOR.
ARRANTY MAY BE JEOPARDIZED IF ALUMINUM IRE IS CONNECTED TO UNIT
CONTACTOR.
Special instructions apply for power wiring with aluminum conductors: Warranty
is void if connections are not made per instructions.
Attach a length (6(or more) of recommended size copper wire to the unit contactor ter-
minals L1 and L3 for single phase, L1, L2 and L3 for three phase.
Select the equivalent aluminum wire size from Table 6:
Splice copper wire pigtails to aluminum wire with U.L. recognized connectors for copper-
aluminum splices. Please exercise the following instructions very carefully to obtain a
positive and lasting connection:
1. Strip insulation from aluminum conductor.
2. Coat the stripped end of the aluminum wire with the recommended inhibitor, and
wire brush the aluminum surface through inhibitor. NH B TORS: Brundy-Pentex “A”;
Alcoa-No. 2EJC; T & B-KPOR Shield.
3. Clean and recoat aluminum conductor with inhibitor.
WIRE SIZE, AWG
FIGURE 19
FIGURE 20
TYPICAL T ERMOSTAT WIRING
14
1/2(
7/8(
12
1/2(
7/8(
10
1/2(
7/8(
8
3/4(
1-31/32(
6
1(
1-23/64(
4
1(
1-23/64(
3
1-1/4(
1-23/32(
2
1-1/4(
1-23/32(
1
1-1/2(
1-31/32(
0
1-1/2(
1-31/32(
00
2(
2-15/32(
000
2(
2-15/32(
CONDUIT SIZE
OLE SIZE
NOTES: 1. DETERM NE REQU RED W RE S ZE FROM M N MUM C RCU T AMPAC TY SHOWN N NSTALLAT ON & OPERAT NG NSTRUCT ON.
2. BOTTOM POWER ENTRY W LL NOT ACCOMMODATE W RE LARGER THAN #2 AWG (SHADED AREA).
ST-A1141
EXAMPLE FOR CONNECT NG
THRU-BASE POWER AND
CONTROL W R NG. ALL
CONNECT ONS TO USE
WATER-T GHT F TT NGS.
MA NTA N CLEARANCE
W TH ALL COPPER TUB NG.
HIGH VOLTAGE
DISCONNECT
SWITCH
ST-A1294
T1
T2
T3
L1
L2
L3
Y2 Y1 GRW
LOW VOLTAGE
WIRE LEADS
CHASSIS GROUND
FOR INTERNAL WIRING SEE WIRING LABEL ATTACHED TO UNIT.
HIGH VOLTAGE POWER WIRING
24 VOLT CONTROL WIRING
THERMOSTAT
SUBBASE
RW
Y1
Y2
G
HEAT
POWER
FAN
1ST. STAGE COOL
2ND. STAGE COOL

19
4. Make the splice using the wire nuts or split bolt connectors shown in Table 6.
5. Coat the entire connection with inhibitor and wrap with electrical insulating tape.
B. HOOK-UP
To wire unit, refer to the following hook-up diagram.
Refer to Figures 3 and 18 for location of wiring entrances.
Wiring to be done in the field between the unit and devices not attached to the unit, or
between separate devices which are field installed and located, shall conform with the
temperature limitation for Type T wire [63°F rise (35°C)] when installed in accordance
with the manufacturer’s instructions.
C. I TER AL WIRI G
IMPORTANT: Some single phase units are equipped with a single pole contactor.
Caution must be exercised when servicing as only one leg of the power supply is broken
with the contactor.
Some models are equipped with electronically commutated blower motors which are
constantly energized, unless the main unit disconnect is in the off position.
A diagram of the internal wiring of this unit is located under the electrical box cover and
this manual. f any of the original wire as supplied with the appliance must be replaced,
the wire gauge and insulation must be same as original wiring.
Transformer is factory wired for 230 volts on 208/230 volt models and must be changed
for 208 volt applications. See unit wiring diagram for 208 volt wiring.
D. THERMOSTAT
The room thermostat must be compatible with the spark ignition control on the unit.
Generally, all thermostats that are not of the “current robbing” type are compatible with
the integrated furnace control. The low voltage wiring should be sized as shown in
Table 6.
nstall the room thermostat in accordance with the instruction sheet packed in the box
with the thermostat. Run the thermostat lead wires inside the compressor access panel
compartment and connect to low voltage terminals as shown on the wiring diagram.
Never install the thermostat on an outside wall or where it will be influenced by drafts,
concealed hot or cold water pipes or ducts, lighting fixtures, radiation from fireplace, sun
rays, lamps, televisions, radios or air streams from registers. Refer to instructions
packed with the thermostat for “heater” selection or adjustment.
The following are the recommended thermostats available through the manufacturer to
be used:
FIELD WIRE SIZE FOR 24 VOLT T ERMOSTAT CIRCUITS
SOLID COPPER WIRE - AWG.
3.0 16 14 12 10 10 10
2.5 16 14 12 12 12 10
2.0 18 16 14 12 12 10
50 100 150 200 250 300
Length of Run – Feet (1)
Thermostat Load -
Amps
TABLE 7
(1) The total wire length is the distance from the furnace to the thermo-
stat and back to the furnace.
NOTE: DO NOT USE CONTROL W R NG SMALLER THAN NO. 18
AWG.
W/O Economizer W/Economizer
(-)HC-TST213GESS (-)HC-TST213UNMS
(-)HC-TST213UNMS (-)HC-TST305UNMS
(-)HC-TST305UNMS (-)HC-TST314UNMS
(-)HC-TST314UNMS

20
X. FUR ACE SECTIO CO TROLS A D
IG ITIO SYSTEM
ORMAL FUR ACE OPERATI G SEQUE CE
This unit is equipped with an integrated direct spark ignition control.
1. The thermostat calls for heat.
2. The control board will run a self check to verify that the limit control and manual
reset overtemperature control are closed and that the pressure switch is open.
3. Upon closure of the pressure switch, the control board energizes the induced draft
blower for a 15 second prepurge.
4. After the 15 second prepurge, the gas valve opens and the spark is initiated for 7
second trial for ignition.
5. Burners ignite and flame sensor proves all burners have lit.
6. The circulating air blower is energized after 30 seconds.
7. The control board enters a normal operation loop in which all safety controls are
monitored continuously.
8. Thermostat is satisfied and opens.
9. The gas valve is de-energized and closes, shutting down the burner flame.
10. The control board will de-energize the inducer after a five second post purge.
11. The circulating air blower is de-energized after 90 seconds.
The integrated control is a three ignition system.
After a total of three cycles without sensing main burner flame, the system goes into a
100% lockout mode. After one hour, the ignition control repeats the prepurge and igni-
tion cycles for 3 tries and then go into 100% lockout mode again. t continues this
sequence of cycles and lockout each hour until ignition is successful or power is inter-
rupted. During the lockout mode, neither the ignitor or gas valve will be energized until
the system is reset by turning the thermostat to the “OFF” position or interrupting the
electrical power to the unit for 3 seconds or longer. The induced draft blower and main
burner will shut off when the thermostat is satisfied.
The circulating air blower will start and run on the heating speed if the thermostat fan
switch is in the “ON” position.
The integrated furnace control is equipped with diagnostic LED. The LED is lit continu-
ously when there is power to the control, with or without a call for heat. f theLED is not
lit, there is either no power to the control or there is an internal component failure within
the control, and the control should be replaced.
f the control detects the following failures, the LED will flash on for approximately 1/4
second, then off for 3/4 second for designated failure detections.
1 Flash: Failed to detect flame within the three tries for ignition.
2 Flash: Pressure switch or induced draft blower problem detected.
3 Flash: High limit or auxiliary limit open.
4 Flash: Flame sensed and gas valve not energized or flame sensed with no “W” signal.
5 Flash: Overtemperature switch open.
OPERATI G I STRUCTIO S
This appliance is equipped with integrated furnace control. This device lights the main
burners each time the room thermostat (closes) calls for heat. See operating instructions
on the back of the furnace/controls access panel.
TO START T E FURNACE
1. STOP! Read the safety information on the Operating nstructions label located on
this appliance.
2. Set the thermostat to its lowest setting.
3. Turn off all electric power to the appliance.
4. This appliance does not have a pilot. t is equipped with an ignition device which
automatically lights the burner. Do NOT try to light the burner by hand.
!WAR I G
DO NOT ATTEMPT TO MANUALLY LIG T T IS FURNACE WIT A MATC OR
ANY OPEN FLAME. ATTEMPTING TO DO SO CAN CAUSE AN EXPLOSION OR
FIRE RESULTING IN PROPERTY DAMAGE, PERSONAL INJURY OR DEAT .
!WAR I G
IF YOU DO NOT FOLLOW T ESE INSTRUCTIONS EXACTLY, A FIRE OR
EXPLOSION MAY RESULT CAUSING PROPERTY DAMAGE, PERSONAL
INJURY OR LOSS OF LIFE.