Rhino-Rack Jerry Can Holder User manual

Page 1 of 5
43107 Rhino Jerry Can Holder
43108 Rhino Jerry Can Holder - Horizontal
Important: Please read these instructions carefully prior to installation.
 Checkthecontentsofkitbeforecommencingtmentandreportanydiscrepancies.
Clean the alloy tray prior to installation.
Place these instructions in the vehicle’s glove box after installation is complete.
Recommendations:
Use only non-stretch fastening ropes or straps. Do not overload your Rhino-Rack Alloy Tray and roof bars. Check your
vehicle’s roof carrying capacity. Exercise caution when driving off road as vehicle roof height has been increased.
Caution:
The handling characteristics of the vehicle change when you transport a load on the roof. For safety reasons, we
recommend exercising extreme care when transporting large wind-resisting loads; special consideration must be taken
into account when negotiating corners and under braking.
Note for Dealers and Fitters:
It is your responsibility to ensure instructions are given to the end user or client.
Rhino-Rack
3 Pike Street, Rydalmere,
NSW 2116, Australia. Document No: RR242
(Ph) [phone] Prepared By: Nigel Greig Issue No: 08
(Fax) [phone] Authorised By: Chris Murty Issue Date: 30/06/2015
These instructions remain the property of RhinoRack Australia Pty. Ltd. and may not be used or changed for any other purpose than intended.
Important Information
Layout
Internal Dimensions:
43107 Vertical: 366 x 170mm
43108 Horizontal: 480 x 170mm
CONTROLLED

Rhino Alloy Tray Fitment . . . . . . . . . . . . . . . . . . Proceed to Step 1.
Parts List
Tools Required:
16mm Spanner 13mm Spanner
10mm Spanner Screwdriver
Item Component Name Part No. Qty.
1 Jerry Can Holder C693 1
1 Jerry Can Holder - Horizontal C694
2 Stainless Steel Ratchet 25mm CA1133 1
3 Mount Bracket Left C695 1
4 Mount Bracket Right C696 1
5 M10 x 40mm Hex Bolt B006 1
6 M10 x 25mm Hex Bolt B071 1
7 M10 Shakeproof Washer W021 1
8 M10 x 30mm Flat Washer W023 1
9 M10 Channel Nut N024 1
10 M8 x 16mm Hex Bolt B019 2
11 M8 Spring Washer W019 2
12 M8 x 17mm Flat Washer W020 2
13 M8 Channel Nut N003 2
14 M6 x 16mm Hex Bolt B168 4
15 M6 x 12.5mm Flat Washer W003 8
16 M6 Nyloc Nut N013 4
17 Fitting Instructions RS-242 1
Jerry Can Holder Vertical
or
Jerry Can Holder Horizontal
3
4
5
6
7
8
9
10
11
12
2
13
14
15
16
Rhino Pioneer Alloy Tray Fitment . . . . . . . . . . . . . . . . . . Proceed to Step 5.
1
Page 2 of 5
43107 Rhino Jerry Can Holder
43108 Rhino Jerry Can Holder - Horizontal
1Fit Mount Brackets:
Place the jerry can holder up-side down on your work bench. Proceed to t the left and right mount brackets with
the hardware supplied as shown below.
M6 x 16mm Hex Bolt
M6 x 12.5mm Flat Washer
M6 x 12.5mm Flat Washer
M6 Nyloc Nut
Brackets tted to inside

3Remove Eye Bolt:
Decide which corner you would like the jerry can to be
located on the alloy tray. Remove the eye nut in this
location with the shank of a screwdriver. Remove the
shakeproof and at washer below the eye nut on the
alloy tray.
Please Note:
If the existing bolt is M10 x 35mm replace it with the M10
x 40mm bolt provided, you will have to remove more eye
nuts and loosen some allen key bolts to slide the bolt
and tab cage in and out of the bar.
Remove the ‘V Tab’ and leave off.
2Fit Hardware to Jerry Can Holder:
Fit hardware to the long mount bracket on the jerry can holder as shown, leave the hardware loose at this stage.
Long
Mount Bracket
M10 x 25mm Hex Bolt
M10 Shakeproof Washer
M10 x 30mm Flat Washer
M10 Channel Nut
Page 3 of 5
43107 Rhino Jerry Can Holder
43108 Rhino Jerry Can Holder - Horizontal
4Fit Jerry Can Holder to Tray:
Lower the jerry can holder onto the tray making sure that
the bolt in the tray goes through the hole in the mount
bracket.
Fit the eye bolt and washers as shown. On the opposite
side make sure that the channel nut rotates 90° when
inserted into the commercial bar.
Tighten the M10 bolt with a spanner. Tighten the eye nut
with the shank of a screwdriver as shown below.
Proceed to Step 6.
M10 Eye Bolt
M10 Shakeproof Washer
M10 x 30 Flat Washer

5Fit Jerry Can Holder to Plank:
Lower the jerry can holder onto the plank where you would like to t the unit. Place two M8 channel nuts into the slot at
the end of the plank and slide the channel nuts under the tabs at each end of the jerry can holder. Fit the hardware to
the channel nuts as shown and fasten in position.
Fitment Note: Jerry can holder must always be tted to the outside plank of the tray. It must also be centred
over one of crossbars running beneath the planks as the strap brackets need to be tted to the crossbar.
Multiple Jerry Can Holders: When tting multiple jerry can holders to the same tray the load must be
distributed evenly over the tray. Fitment note above must also be followed.
Rhino Pioneer Alloy Tray Fitment
Plank
M8
Channel Nut
M8 x 16mm Hex Screw
M8 x 17mm Flat Washer
M8 Spring Washer
Slot
6Insert Jerry Can:
Insert the jerry can to be used into the jerry can holder as shown below.
It is important to keep
the ller cap facing
upwards when you
load the jerry can into
the holder.
Horizontal
Jerry Can Holder
Vertical
Jerry Can Holder
Page 4 of 5
43107 Rhino Jerry Can Holder
43108 Rhino Jerry Can Holder - Horizontal

7Fit Ratchet Strap:
Horizontal Holder:
Lay the ratchet strap over the middle of the
jerry can holder as shown. Wrap the ratchet
end of the strap under the crossbar and feed
through the loop, gently pull the ratchet until
the strap is rmly in place. Repeat this for the
opposite side, ensure that the strap is kept as
close to the jerry can holder as possible.
Tighten the ratchet strap until the jerry can is
secure.
Vertical Holder:
Insert the ratchet strap through the handle of
the jerry can as shown. Wrap the ratchet end of
the strap under the crossbar and feed through
the loop, gently pull the ratchet until the strap is
rmly in place. Repeat this for the opposite side,
ensure that the strap is kept as close to the jerry
can holder as possible.
Tighten the ratchet strap until the jerry can is
secure.
Page 5 of 5
43107 Rhino Jerry Can Holder
43108 Rhino Jerry Can Holder - Horizontal