Rice Lake 160-10-7N User manual

160-10-7N
Low-Profile Digital Athletic Scale
Software Version 11525
Technical Manual
PN 194095 Rev CAugust 18, 2022

© Rice Lake Weighing Systems. All rights reserved.
Rice Lake Weighing Systems® is a registered trademark of
Rice Lake Weighing Systems.
All other brand or product names within this publication are trademarks or
registered trademarks of their respective companies.
All information contained within this publication is, to the best of our knowledge, complete and
accurate at the time of publication. Rice Lake Weighing Systems reserves the right to make
changes to the technology, features, specifications and design of the equipment without notice.
The most current version of this publication, software, firmware and all other product
updates can be found on our website:
www.ricelake.com

Revision History
© Rice Lake Weighing Systems ● All Rights Reserved i
Technical training seminars are available through Rice Lake Weighing Systems.
Course descriptions and dates can be viewed at www.ricelake.com/training
or obtained by calling 715-234-9171 and asking for the training department.
Revision History
This section tracks and describes the current and previous manual revisions for awareness of major updates and when the
updates took place.
Revision Date Description
C August 18, 2022 Established a revision history; formatted content to match other medical manuals; software version 11525
Table i. Revision Letter History

Contents
160-10-7N Low-Profile Digital Athletic Scale
ii Visit our website www.RiceLake.com
Rice Lake continually offers web-based video training on a growing selection
of product-related topics at no cost. Visit www.ricelake.com/webinars
1.0 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1.1 FCC Compliance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1.2 Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
2.0 Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2.1 Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2.1.1 Repacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2.2 Scale Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2.2.1 Leveling the Scale . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2.3 Indicator Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2.3.1 Load Cell Connection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2.3.2 Insert Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2.3.3 Power Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
3.0 Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
3.1 Key Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
3.2 Weighing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
3.3 Hold/Release Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
3.4 Preset Tare . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
3.5 Toggle Tare. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
3.6 Using the Body Mass Index (BMI) Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
3.6.1 LB Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
3.6.2 KG Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
3.7 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
4.0 Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
4.1 Setup Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
4.2 Setup Mode Navigation: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
4.3 General Navigation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
4.3.1 Change Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
4.3.2 Enter Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
4.3.3 Save and Return to Main Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
4.4 User Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
4.5 Configuration Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
4.6 Default Scale. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
4.7 Program Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
4.8 Scale Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
4.9 Test Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
5.0 Communication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
5.1 Push-button Keypad Print . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
5.2 Communication Protocols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
5.2.1 Escape Protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
5.2.2 Maintenance Protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
5.3 USB Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
6.0 Sealing of the Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
6.1 NTEP Regulations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
6.2 Measurement Canada Regulations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
7.0 Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
7.1 Basic Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
7.2 Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
8.0 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Introduction
© Rice Lake Weighing Systems ● All Rights Reserved 1
1.0 Introduction
The 160-10-7N low-profile digital athletic scale is efficiently designed to provide accurate, reliable and repeatable weight
measurements. The large, stand-alone indicator can be placed on a table or the floor. It can also be mounted to a wall using the
sturdy, built-in bracket. The 160-10-7N low-profile digital athletic scale is an NTEP-certified device that provides the highest
possible accuracy when weight is a critical factor.
Manuals, resources and warranties are available from Rice Lake Weighing Systems website at
www.ricelake.com/health
1.1 FCC Compliance
United States
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated
in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the
interference at his own expense.
Canada
This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus set out in the Radio
Interference Regulations of the Canadian Department of Communications.
Le présent appareil numérique n'émet pas de bruits radioélectriques dépassant les limites applicables aux appareils
numériques de la Class A prescites dans le Règlement sur le brouillage radioélectrique edicté par le ministère des
Communications du Canada.

160-10-7N Low-Profile Digital Athletic Scale
2 Visit our website www.RiceLake.com
1.2 Safety
Safety Definitions:
Indicates an imminently hazardous situation that, if not avoided, will result in death or serious injury. Includes
hazards that are exposed when guards are removed.
Indicates a potentially hazardous situation that, if not avoided, could result in serious injury or death. Includes
hazards that are exposed when guards are removed.
Indicates a potentially hazardous situation that, if not avoided, could result in minor or moderate injury.
Indicates information about procedures that, if not observed, could result in damage to equipment or corruption
to and loss of data.
General Safety
Do not operate or work on this equipment unless this manual has been read and all instructions are understood.
Failure to follow the instructions or heed the warnings could result in injury or death. Contact any Rice Lake
Weighing Systems dealer for replacement manuals.
Failure to heed could result in serious injury or death.
Ensure every individual who operates or works with this unit has read and understands all safety information.
Do not transport the scale while someone is on the scale.
Do not allow minors (children) or inexperienced persons to operate this scale.
Do not use in the presence of flammable materials.
Do not use this product if any of the components are loose or cracked.
Do not use near water.
Do not use the scale on slippery surfaces, such as a wet floor.
Do not use this scale when a person’s body or feet are wet, such as after taking a bath.
Do not place fingers into slots or possible pinch points.
To avoid cross contamination, the scale should be cleaned regularly.
Prior to cleaning, make sure the scale is disconnected from the power source.
People with disabilities, or who are physically frail, should always be assisted by another person when using this scale.
Do not drop the scale or subject it to violent shocks.
Do not jump on the scale.
For accurate weighing, the scale must be placed on a flat, stable surface.
Operating at voltages and frequencies other than specified could damage the equipment.
Avoid contact with excessive moisture.
Do not make alterations or modifications to the scale.
Rice Lake Weighing Systems offers optional AC adapters; utilizing an adapter not supplied by Rice Lake Weighing Systems voids
all warranties and approvals.
Weight exceeding the maximum capacity may damage the scale.
DANGER
WARNING
CAUTION
IMPORTANT
WARNING
IMPORTANT

Assembly
© Rice Lake Weighing Systems ● All Rights Reserved 3
2.0 Assembly
2.1 Unpacking
Place the unopened shipping container in an open area with room for unpacking the scale. If parts were damaged in shipment,
notify Rice Lake Weighing Systems and the shipper immediately. Parts included:
• Scale base and indicator
• Six AA batteries
• AC adapter
• USB 2.0 Cable AM/BM 1.5 M
• Serial cable 9.5 feet with female DB9 and RJ45 connectors
2.1.1 Repacking
Retain the packaging for use in the event that the scale must be returned or moved. It must be properly packed with sufficient
packing materials. Whenever possible, use the original shipping carton when shipping the scale back.
Damage caused by improper packaging is not covered by the warranty.
2.2 Scale Setup
Place the scale on a hard level surface for the most accurate weighments.
Thin carpeting is acceptable but is not recommended. Weighing on carpet can cause a weight discrepancy.
2.2.1 Leveling the Scale
On a flat surface, adjust scale feet until the bubble level indicates that the scale is level.
Figure 2-1. Bubble Level
IMPORTANT
Note

160-10-7N Low-Profile Digital Athletic Scale
4 Visit our website www.RiceLake.com
2.3 Indicator Setup
Use the following sections to set up the provided Rice Lake Indicator.
2.3.1 Load Cell Connection
The indicator and scale comes factory installed with a load cell cable connection. Follow the procedure below if the load cell
cable needs to be replaced or reconnected to the indicator.
1. Unscrew and remove the tilt stand bracket from the indicator to gain access to the load cell connection.
Figure 2-2. Remove Tilt Stand
2. Remove the four back retaining screws to remove the back cover to the indicator.
Figure 2-3. Remove Back Cover
3. Plug the end of the load cell cable into the load cell connection. When it clicks the load cell cable is properly seated
into the connection.
Figure 2-4. Load Cell Connection Point
4. Reinstall the back cover and attach to the tilt stand.
Unscrew tilt stand
knobs and remove tilt
stand from indicator
Load Cell
Connection
Do Not Use this
Connection for
Load Cells

Assembly
© Rice Lake Weighing Systems ● All Rights Reserved 5
2.3.2 Insert Batteries
The six AA batteries supplied with the scale provide an average of 25 hours of continuous use.
To install the batteries:
1. Turn thumbscrew counterclockwise then remove battery cover.
2. Insert batteries into the battery chamber as illustrated.
Figure 2-5. Battery Chamber
3. Put the cover in place and turn the thumbscrew clockwise to secure.
Remove the batteries prior to storing if the product is not going to be used for an extended period of time.
If the LO BAT indicator activates, for accurate weighing, replace the batteries or connect the scale to an AC power
source as soon as possible.
2.3.3 Power Connection
An optional AC power adapter can be used when a power outlet is available.
Only use power adapters supplied by or purchased from Rice Lake Weighing Systems. The use of a power
adapter not from Rice Lake Weighing Systems voids the warranty.
Figure 2-6. Power Connection Site
The battery annunciator on the display turns off when using an AC power connection.
The brightness of the backlight is reduced to 60% when using battery power.
Thumb Screw
Note
Note
IMPORTANT
AC Power
Connection
Note

160-10-7N Low-Profile Digital Athletic Scale
6 Visit our website www.RiceLake.com
3.0 Operation
This section describes the front panel and includes procedures for operation of the scale.
Figure 3-1. Front Panel Keypad
3.1 Key Descriptions
The display has 10 front panel keys. Key functions are described in the table below.
The front panel keys are very sensitive, so only a gentle press is required.
Key Name Function
On/Off Powers the scale on or off
Print
LB/KG
Sends data out from the RS-232 port; Allows to toggle between kilograms and pounds providing that it is enabled in
Configuration mode; Cannot toggle while in the BMI mode
Zero Only functions if the current weight is stable and less than 2% of the capacity of the scale. Anything over 2% requires
a recalibration
Hold Release Does not function when set up as an NTEP-certified scale.
Displays most current weight value on the display and holds that value when the patient is off the scale. A second
press releases the weight value. Not active while in BMI mode
BMI Does not function when set up as an NTEP-certified scale.
Pressing the BMI key enables access to the BMI (Body Mass Index) mode (defaults when scale is turned on). The
patient is gets on the scale, weight stabilizes and press the BMI key. The display then asks for the patient height to
calculate out the patient BMI.
TARE Used to remove the weight initially of anything on the scale that shouldn’t be included in the total weight of the
patient on the scale
CLEAR When using the BMI function, the display looks for a height entry. Pressing Clear changes this entry back to 190.0
cm (default) or 5 ft, 7.5 in.Once BMI is displayed, pressing the Clear key exits BMI
ENTER Used to accept height in BMI mode; accepts the value of the parameter last entered and moves to the next stage
Pressing and holding Enter during startup will display ID. This is the first setup on entering into configuration mode
Up Arrows Adjusts the value of the flashing digit/number
Adjusts height input (0.5 in/0.5 cm) while in BMI mode
Down Arrows Adjusts the value of the flashing digit/number
Adjusts height input (0.5 in/0.5 cm) while in BMI mode
Table 3-1. Key Functions
IMPORTANT
On/O
LB/KG
Print
Zero
Hold
Release
BMI
TARE
T
CLEAR
ENTER

Operation
© Rice Lake Weighing Systems ● All Rights Reserved 7
3.2 Weighing
Use the following steps to weigh.
1. Press to turn on the scale. 0.0 prompts along with ZERO on the display.
2. Place the patient on the scale. The patient’s weight is displayed, the LOCK annunciator is on and the indicator beeps
to indicate the end of the weighing process.
3. Press to change the display from lb to kg and vice-versa.
4. Press and hold until OFF displays to turn off the scale.
3.3 Hold/Release Function
Use the following steps to use the Hold/Release function.
1. Press to turn on the scale. 0.0 prompts along with ZERO on the display.
2. Press once the patient’s weight stabilizes. The patient’s weight and the HOLD and LOCK annunciators remain
on the display when the patient is off the scale.
3. Press again to return the scale to zero.
Pressing will not work while using Hold/Release function.
Pressing prior to the patient getting on the scale will also hold the weight display.
3.4 Preset Tare
Use the following steps for the Preset Tare function prior to patient weighing if additional items are being used by the patient.
1. Press to turn on the scale. 0.0 appears on the display along with the ZERO annunciator.
2. Place additional item(s) on the scale.
3. Press until the display returns to 0.0 and NET annunciator appears on the display.
4. Remove additional item(s) from the scale. The weight displays with a negative symbol to the left of it.
Not removing the additional item(s) prior to patient weighing will also work.
5. Position the patient and additional item(s) on the scale. The display identifies the patient weight. The NET annunciator
is still active. The weight of the additional item(s) remains stored in memory for the duration of this weigh in.
6. To cancel the tare weight, remove patient from the scale and press until NET disappears from the display and
the display turns back to 0.0 and GROSS appears.
Tare weight is also canceled when the scale is turned off.
3.5 Toggle Tare
Use the following steps to use the Toggle Tare function when the additional item to be weighed is known.
1. Press when the scale is empty and 0.0 displays. The default values prompts while 0.0 is flashing on the display
(default is programmed to be 33.0 lb/15.0 kg).
2. Use and to adjust the value. Press to start the tare function. The NET annunciator turns on instead
of the GROSS annunciator.
Note
Note
TARE
T
Note
TARE
T
Note
TARE
T
ENTER

160-10-7N Low-Profile Digital Athletic Scale
8 Visit our website www.RiceLake.com
3.6 Using the Body Mass Index (BMI) Function
The BMI key does not function when set up as an NTEP-certified scale.
Use the following steps in determining the BMI.
3.6.1 LB Mode
1. Ensure that the scale is at zero.
2. Have the patient step onto the scale to obtain a weight. The LOCK annunciator appears on the display.
3. Press . The BMI and FT/IN annunciators are lit on the display and a default height value of 5 feet - 7.5 inch is
flashing.
4. Use and to adjust the height value.
5. Press .
6. The BMI value and BMI annunciator are shown on the display. Press to return to the Weighing mode and the
BMI function will be turned off.
3.6.2 KG Mode
1. Ensure that the scale is at zero.
2. Have the patient step on the scale to obtain a weight.The LOCK annunciator appears on the display.
3. Press . The BMI and CM annunciators appear on the display and a default height value of 170.0 cm (170.0) is
flashing.
4. Use and to adjust the height value.
5. Press .
6. The BMI value and BMI annunciator are shown on the display. Press to return to the Weighing mode and the
BMI function will be turned off.
Note
BMI
ENTER
CLEAR
BMI
ENTER
CLEAR

Operation
© Rice Lake Weighing Systems ● All Rights Reserved 9
3.7 Troubleshooting
Refer to the following table to check and correct any failure before contacting service personnel.
Symptom Possible Cause Corrective Action
Scale does not turn on Dead batteries Replace batteries or connect to AC power
Faulty electrical outlet Use a different electrical outlet
Bad power supply Replace adapter
Questionable weight or the scale does not
zero
External object is interfering with the scale Remove the interfering object from the scale
Display did not show 0.0 before weighing Help the patient off the scale, zero the scale and begin the
weighing process again
Scale is not placed on a level floor Ensure scale is level and begin the weighing process again
Scale is out of calibration Check the weight with a certified calibration weight
The display shows a STOP message The load on the scale exceeds the
capacity of the scale
Remove the excess weight and use the scale according to
manufacture specifications
The display shows LO Bat message The battery is low Replace batteries
The display shows E and Err messages as detailed below
E06 Identifier - ADC AD too high
E07 AD too low
E10 Overload Scale has been overloaded. Remove load from scale
E4L BAT Battery low, but still usable- one bar left on indicator display
E4U Battery low and unstable - no bars left on indicator display
E11 CAL Calibration Error - recalibrate scale
Err 1 Load cell cable may be plugged into wrong
connection port
Ensure cable is connected to the load cell connection port
Note: Load cell connection point is located underneath the
curved plastic cover of the indicator. Remove four back
retaining screws, remove curved back cover to access load
cell connection point.
Err 2 Low saturation state (low A/D) The load cell is not connected properly; Check the cables
and mechanical connections; if the problem persists, replace
the set of load cells
Err 3 High saturation state (high A/D) See Err 2
Err 6 Unstable weight; Cannot calibrate Check the load cell mechanical surroundings and ensure
nothing is contacting the load cell and that the cables are
properly welded
Err 7 Scale isn’t moving Make sure feet are installed on the scale. Turn the feet all
the way in and then back them out three full turns, then level
the scale
SAT Damaged load cell cable Replace load cell cable
Load cell cable may be plugged into wrong
connection port
Ensure cable is connected to the load cell connection port
Note: Load cell connection point is located underneath the
curved plastic cover of the indicator. Remove four back
retaining screws, remove curved back cover to access load
cell connection point.
Table 3-2. Troubleshooting Table

160-10-7N Low-Profile Digital Athletic Scale
10 Visit our website www.RiceLake.com
4.0 Configuration
Options and parameter setup are done through the scale navigation.
4.1 Setup Mode
Accessing the setup menu require the indicator to be in setup mode. It is necessary to break the seal and remove the back
cover to put the indicator into setup mode.Use a Phillips head screwdriver to remove the four screws holding the cover in place
(shown below - left photo).
Figure 4-1. Back of Indicator
4.2 Setup Mode Navigation:
1. Ensure the scale is off.
2. Remove the back plate by loosening the two Phillips screws and two drilled hex head screws (Figure 4-1).
3. Press to turn on the indicator. START displays.
4. Press and hold until ID and it’s value flashes.
Use a small non-conductive tool to press the setup switch. PROG displays.
4.3 General Navigation
Use the buttons on the front panel to navigate through the menus and parameters.
4.3.1 Change Parameters
• Press to scroll through the menus and/or parameters
• Press to enter a displayed menu and/or parameter
• Press or to scroll through values
• Press to save the displayed selection and move to the next parameter
Setup Switch
ENTER
BMI
ENTER
ENTER

• Press
ENTER
to enter parameter value
• Press or to increment/decrement numbers
•
Press
BMI
to move to the next digit
•
Press
ENTER
to save value and move to the next parameter
Configuration
© Rice Lake Weighing Systems ● All Rights Reserved 11
4.3.3 Save and Return to Main Menu
• When a parameters selection/value is correct, press . The next parameter displays
• When all parameters selections/values are correct, SAVE displays
• Press . DONE displays.
• Press to save settings and return to weigh mode.
ENTER
ENTER
ENTER
4.3.2 Enter Numbers
ENTER
ENTER
BMI

160-10-7N Low-Profile Digital Athletic Scale
12 Visit our website www.RiceLake.com
4.4 User Menu
The User Menu allows a user to set the baud, auto off time and turn several other functions on or off.
Figure 4-2. User Menu
User Menu Navigation:
1. Press to turn on the indicator. START displays.
2. Press and hold until ID and it’s value flashes.
3. Press . TEST displays.
4. Press . USER displays.
5. Press . BAUD and it’s value flashes.
6. Press to scroll through the menu items.
7. Press to edit a parameter setting.
8. Press or to select the setting and press to save the setting and move to next parameter.
9. SAVE displays at the end of the menu if a change was made. With SAVE displayed, press . DONE displays.
10. Press . The indicator resumes the self test and returns to weigh mode.
Press when SAVE displays, to return to weigh mode without saving
Parameter Description
BAUD Baud Rate – sets the baud rate; end zeros are not displayed (96 = 9600); Settings: 96 (default), 48, 1152, 576, 384, 288, 192, 144
TOFF Auto Off Timer – turns unit off after the set number of minutes; 0 = always on; battery power only, does not work if using an external power
supply; Settings: 5 (default); 6, 7, 8, 9, 0, 1, 2, 3, 4
LIVE Live Weighing – enables or disables live weighing; must be set to ON for use as an certified NTEP scale; if set to OFF, the weight
stabilizes, the LOCK annunciator displays and an audible tone indicates the end of the weighing process; Settings: ON (default), OFF
MAIN Communication Protocol – enables or disables the communication protocol; Settings: OFF (default), ON
TARE Tare – enables or disables the tare function; a tare subtracts weight of accessory items from the scale; Settings: ON (default), OFF
ANTIP Anti Pressing – when set to OFF the display blinks for two seconds when weight is unstable under the ASTART value; when set to ON the
display does not blink; does not function when set up as an NTEP-certified scale (when LIVE set is to OFF); Settings: OFF (default), ON
SAVE Saves settings and returns to upper level; only appears if changes have been made
Table 4-1. User Menu Parameters
ID
TEST USER DONE
BAUD
96
192
144
288
384
576
48
1152
TOFF
5
7
6
8
9
0
2
1
4
3
LIVE
ON
OFF
MAIN
OFF
ON
TARE
ON
OFF
ANTIP
OFF
ON
SAVE
ENTER
ENTER
BMI
ENTER
BMI
ENTER
ENTER
ENTER
ENTER
Note
CLEAR

Configuration
© Rice Lake Weighing Systems ● All Rights Reserved 13
4.5 Configuration Mode
Use the following steps to enter into Configuration mode.
1. Ensure the scale is turned off.
2. Turn the scale on by simultaneously pressing and . Continue to hold both keys until Id appears.
The unit cycles through its startup function and continues to display the software version.
3. Access the setup switch located in the back of the scale to enter the setup parameters for the scale. Use a small paper
clip, small screwdriver or other similar object to press the setup switch.
4. Once the setup switch is pressed, PROG displays.
5. Scale can be configured using a series of menus accessed through the front panel when the scale is in Setup mode.
Figure 4-3. Top Level Menu
6. Press to advance to the desired menu.
7. Press and advance in the manual to the related menu selection for further instructions.
4.6 Default Scale
The default parameter is used to return the scale to the original factory settings. This does not change the calibration.
Figure 4-4. Default Parameter
Default Scale Navigation:
1. Enter setup mode (Section 4.7 on page 14). PROG displays.
2. Press twice. DEF displays.
3. Press . NO displays.
4. Press . YES displays.
5. Press . DONE displays.
6. Press to return to the setup menu. DEF displays.
7. Press . DONE displays.
8. Press . The indicator resumes the self test and returns to weigh mode.
ENTER
See Section 4.9 on page 16
DEFCALIBPROG DONE TEST
Available only when
accessing test menu
BMI
ENTER
DEFCALIBPROG DONE
NO
YES
BMI
ENTER
ENTER
BMI
BMI
ENTER

160-10-7N Low-Profile Digital Athletic Scale
14 Visit our website www.RiceLake.com
4.7 Program Menu
The program menu allows for the setup of the indicator to determine how the scale reads the weight and displays output.
To enter the program menu:
1. Enter setup mode (Section 4.7).
2. With PROG displayed, press .
3. Use the navigation instructions in Section 4.9 on page 16, to set the necessary PROG parameters.
Figure 4-5. Program Menu
Parameter Description
FULL Full Capacity – enter value of the scale capacity; default: 550.0 lb
LOAD Load – weight applied during calibration (can also be set during calibration process); default: 200.0 lb
G-CAL Gravity Calibration – sets gravity for original calibration; default: 00000
G-LOC Gravity Location – sets gravity for location of use; default: 00000
ASTRT Auto-Start – weight process start limit; maximum (full capacity)/10; determines when the weight algorithm starts; default: 4.0 lb
ARW Auto Reweigh – restarts the weight algorithm if the weight changed by more than this value; default: 4.0 lb
SAL Semi Auto Live – interval between weight displays during the algorithm process; default: 0.5
ROUND Scale Resolution – sets the scale resolution value; Settings: 0.2 lb (default), 0.5, 1.0, 2.0, 5.0, 10.0, 20.0, 0.2
DISP Decimal Point – sets the decimal point location; Settings: 0.0 (default), 00000, 0.0000, 0.000, 0.00
BAUD Baud Rate – sets the baud rate; end zeros are not displayed (96 = 9600); Settings: 96 (default), 144, 192, 288, 384, 576, 1152, 48
ATOL Algorithm Initial Tolerance – a value above 255 (max) does not allow indicator to proceed and returns to the previous value; default: 10
ALEN Algorithm Initial Exponent – a value above 10 (max) does not allow indicator to proceed and returns to the previous value; default: 8
ATOUT Algorithm Maximal Exponent – a value above 15 (max) does not allow indicator to proceed and returns to the previous value; default: 10
TOFF Auto Off Timer – turns unit off after the set number of minutes; 0-9 minutes; 0 = always on; default: 5 min
NOTE: Battery power only, does not work if using an external power supply.
SPACE Space – number of new lines after print; default: 7
Table 4-2. Program Menu Parameters
ENTER
PROG
FULL LOAD G-CAL G-LOC ASTRT ARW SAL ROUND DISP
value value value value value value value
20.0
5.0
10.0
2.0
0.5
1.0
0.2 0.0
0.0000
00000
0.000
0.00
5
7
6
8
9
0
2
1
4
3
96
192
144
288
384
576
48
1152
BAUD ATOL ALEN ATOUT TOFF SPACE UNITS OP SAVE
value value value value PXX-X
LB/KG
LB
KG

Configuration
© Rice Lake Weighing Systems ● All Rights Reserved 15
4.8 Scale Calibration
Use the following steps to calibrate the scale.
1. Enter the setup mode (Section 4.7 on page 14). PROG displays.
2. Press . CALIB displays.
3. Press . A numeric value displays (weight to be used for calibration).
Calibrate in the unit of measure that the scale is intended to be used. Press or to change units.
4. Press . The digit on the right flashes.
• Press or to change the value of digit.
• Press to move to the next digit.
• When the desired value is displayed, press . CLEAR displays.
To quit calibration, press or . ABORT displays. Press to abort and return to upper level.
5. Remove all weight from scale platform, then press . ===== displays.
6. When PUT and set weight value flashes on display, put the displayed weight value on the scale platform.
7. Press . ===== and then Save displays.
Press to exit calibration without changing the existing zero or span calibration.
8. Press . DONE displays.
9. Press three times to navigate to the top level DONE parameter.
10. Press . The indicator resumes the self test and returns to weigh mode.
UNITS Units – select the unit of measure; Settings: LB/KG (default), LB, KG
NOTE: When indicator is set to LB or KG, toggling between them is not available in the weighing mode.
OP Binary options:
• P00 — Live weighing options (0=disable, 1=enable); default: 1
• P01 — Communication protocol (0=ESC, 1=maintenance); default: 0
• P02 — BMI menu (0=disable, 1=enable); default: 1
• P03 — RTC power (0=disable, 1=enable); default: 0
• P04 — Semi Auto Live (0=disable, 1=enable); default: 1
• P05 — Full calculation (0=spatial, 1=multiply by (0=disable, 1=enable); default: 0
• P06 — Tare (0=disable, 1=enable); default: 1
• P07 — Bat type (0=dry batteries, 1=rechargeable batteries); default: 0
• P08 — OIML mode (0=disable, 1=enable); default: 1
• P09 — USB (0=disable, 1=enable); default: 0
• P10 — Anti pressing (0=disable, 1=enable); default: 0
• P11 — Last (0=off, 1=on); default: 1
SAVE Saves settings and returns to upper level
Parameter Description
Table 4-2. Program Menu Parameters (Continued)
BMI
ENTER
Note
ENTER
BMI
ENTER
Note
BMI
ENTER
ENTER
Note
BMI
ENTER
BMI
ENTER

160-10-7N Low-Profile Digital Athletic Scale
16 Visit our website www.RiceLake.com
4.9 Test Menu
This menu is read only.
Figure 4-6. Test Menu
Test Menu Navigation:
1. Press to turn on the indicator. START displays.
2. Press and hold until ID and it’s value flashes.
3. Press . TEST displays.
4. Press . RID and it’s value flashes.
5. Press to scroll through the menu items.
6. When TEST displays again, press two times to navigate to the top level DONE parameter.
7. Press . The indicator resumes the self test and returns to weigh mode.
Parameter Description
RID Internal ID number
VER Development internal sub version
A2D Raw weight data
VALUE Processed weight in live display
BAT Relative raw battery value
Table 4-3. Test Menu Parameters
ID
TEST
RID VER A2D VALUE BAT
USER DONE
ENTER
ENTER
ENTER
BMI
BMI
ENTER