Ricoh M109 Manual

1
Ti-P1 Training
Slide 1
M109
Service Training
Ti-P1
Version 1.1
This course explains the low-end color A3 printer Ti-P1.
Version 1.1: Changes were made to the following slides
3, 12, 13, 17, 19, 22, 24, 34, 35, 44, 47, 49, 50, 65, 97, 101, 107, 117, 118

2
Ti-P1 Training
Slide 2
M109
Service Training
Product Overview
This section provides an overview of the machine, and the options that can be
installed.

3
Ti-P1 Training
Slide 3
What Models are there in the Series?
Ti-P1a (M109)
32 ppm
Low-end A3 printer
GW+ Controller (2012 Autumn)
Contains PostScript3, Gigabit Ethernet, duplex
unit, and bypass tray as standard equipment.
Main points
LED print head
QSU fusing unit
Eco night sensor
Maintenance can be done by users
No additional notes

4
Ti-P1 Training
Slide 4
Appearance
Up to three one-tray feed units can be installed (not shown
here).
Duplex and bypass are standard.
There are no finishers.
There is no external USB/SD card slot by the operation
panel.
One paper tray
is standard
No additional notes

5
Ti-P1 Training
Slide 5
Options: Paper Feed
Also used with these
new models:
500 sheetsNewOne-tray paper feed unit
(M406): TK2000
NoteSimilar to:
There are no finishers.

6
Ti-P1 Training
Slide 6
Options: Printer
160 GBM417: Hard Disk Drive Option Type C730
M417: IPDS Unit Type C730
M417: Memory Unit Type N 1GB
M417: SD card for NetWare Printing Type M
D417: Camera Direct Print Card Type L
Note
There is no RPCS driver.

7
Ti-P1 Training
Slide 7
Options: Controller
M417: IEEE 802.11
Interface Unit Type O
AL-P2
Also used with these
new models:
Requires the optional
hard disk
M417: VM Card Type W
B679: IEEE 1284 Interface
Board Type A
Note
No Bluetooth option
VM card: requires optional HDD

8
Ti-P1 Training
Slide 8
Controller Options
Memory Upgrade Options
Optional hard disk
160 GB
Memory
Standard memory: 512 MB
Upgrades: 1 GB memory card option
» There is only one slot for memory. To upgrade to 1 GB,
remove the standard 512 GB memory and install the 1
GB memory option.
Max possible memory: 1 GB
No additional notes

9
Ti-P1 Training
Slide 9
Ports on the Controller Board
1. USB port A: Connect external
devices such as a digital
camera, a card
authentication device, etc.
Use of a digital camera
requires the Camera
Direct Print option.
2. Expansion card slots:
Remove the cover to install
SD cards.
3. Optional interface board slot:
Insert an optional wireless
LAN interface board or IEEE
1284 interface board.
4. USB port B: Use a USB cable
to connect the printer to a
computer.
5. Ethernet port: Use a network
interface cable to connect
the printer to a network.
1
2
3
4
5
Board Slot: One of the following can be installed.
¾IEEE 802.11a/g Interface Unit Type J or IEEE 802.11g Interface Unit
Type K
¾IEEE 1284 Interface Board Type A
The SD Card slots are discussed in more detail on the next few slides.
Use of a digital camera requires the Camera Direct Print SD card option.
There is a mini USB slot behind the screw above item 4 in the diagram. This
is for designer purposes only.

10
Ti-P1 Training
Slide 10
SD Card Slots (1)
Slot 1 (upper slot):
The slot is empty when shipped
Use when installing the following options
» Camera direct print
» SD card for Netware printing
»VMcard
If the number of options that you wish to install is
more than the number of available SD card slots,
move them onto one SD card.
» Destination card: SD slot 1
If more than one SD card options must be
merged, and the VM card is one of them, the VM
card must be the target SD card.
» The VM card option cannot be moved.
Installation > Controller Options
PDF Direct/PCL/PostScript 3 are pre-installed in the Controller Firmware.