Ricoh MP CW2201 Quick start guide

MP CW2201
Machine Code:
D262
Field Service Manual
March, 2016

Important Safety Notices
Warnings, Cautions, Notes
In this manual, the following important symbols and notations are used.
• A Warning indicates a potentially hazardous situation. Failure to obey a Warning could result in
death or serious injury.
• A Caution indicates a potentially hazardous situation. Failure to obey a Caution could result in
minor or moderate injury or damage to the machine or other property.
• Obey these guidelines to avoid problems such as misfeeds, damage to originals, loss of valuable
data and to prevent damage to the machine.
• This information provides tips and advice about how to best service the machine.
General Safety Instructions
For your safety, please read this manual carefully before you use this product. Keep this manual handy
for future reference.
Safety Information
Always obey the following safety precautions when using this product.
Safety During Operation
In this manual, the following important symbols and notations are used.
[A]: ON
[B]: OFF
[C]: Push ON/Push OFF
[D]: Standby
1

Switches and Symbols
Where symbols are used on or near switches on machines for Europe and other areas, the meaning of
each symbol conforms with IEC60417.
Safety
Prevention of Physical Injury
1. Before disassembling or assembling parts of the machine and peripherals, make sure that the
machine and peripheral power cords are unplugged.
2. The plug should be near the machine and easily accessible.
3. Note that some components of the machine and the paper tray unit are supplied with electrical
voltage even if the main power switch is turned off.
4. Always unplug the power cord from the power source before you move the product. Before you
move the machine, arrange the power cord so it will not fall under the machine.
5. Disconnect all peripheral units (finisher, LCT, etc.) from the mainframe before you move the
machine.
6. If any adjustment or operation check has to be made with exterior covers off or open while the
main switch is turned on, keep hands away from electrified or mechanically driven components.
7. The machine drives some of its components when it completes the warm-up period. Be careful to
keep hands away from the mechanical and electrical components as the machine starts operation.
8. The inside and the metal parts of the fusing unit become extremely hot while the machine is
operating. Be careful to avoid touching those components with your bare hands.
9. To prevent a fire or explosion, keep the machine away from flammable liquids, gases, and
aerosols.
10. Do not use flammable sprays or solvent in the vicinity of the machine. Also, avoid placing these
items in the vicinity of the machine. Doing so could result in fire or electric shock.
11. To avoid fire or explosion, never use an organic cleaner near any part that generates heat.
12. Never remove any safety device unless it requires replacement. Always replace safety devices
immediately.
13. Never do any procedure that defeats the function of any safety device.
14. Modification or removal of a safety device (fuse, switch, etc.) could lead to a fire and personal
injury. Always test the operation of the machine to ensure that it is operating normally and safely
after removal and replacement of any safety device.
15. For replacements use only the correct fuses or circuit breakers rated for use with the machine. Using
replacement devices not designed for use with the machine could lead to a fire and personal
injuries.
2

16. When using a vacuum cleaner around the machine, keep others away from the cleaner, especially
small children.
Observance of Electrical Safety Standards
1. The machine and its peripherals must be installed and maintained by a customer service
representative who has completed the training course on those models with exceptions on some
machines where the installation can be handled by the user.
Safety and Ecological Notes for Disposal
1. Dispose of replaced parts in accordance with local regulations.
2. When keeping used lithium batteries in order to dispose of them later, do not put more than 100
batteries per sealed box. Storing larger numbers or not sealing them apart may lead to chemical
reactions and heat build-up.
3. The danger of explosion exists if a battery of this type is incorrectly replaced. Replace only with the
same or an equivalent type recommended by the manufacturer. Discard used batteries in
accordance with the manufacturer’s instructions.
Safety Instructions for Ink Cartridges
Accidental Exposure To Ink
1. If ink gets on the skin, wash the affected area immediately with soap and cold running water.
2. If ink gets into the eyes, immediately flush the eyes with cold running water. If there are signs
of irritation or other problems, seek medical attention.
3. If ink is swallowed, drink a strong solution of cold water and table salt to induce vomiting.
Seek medical attention immediately.
4. Ink is difficult to remove from fabric. Work carefully to avoid staining clothing when perfo
Handling and Storing Ink Cartridges
• Ink is flammable. Never store ink cartridges in a location where they will be exposed to high
temperature or an open flame.
3

1. Always store ink cartridges out of the reach of children.
2. Always store ink cartridges in a cool, dry location that is not exposed to direct sunlight.
Ink Cartridge Disposal
1. Attach the caps to empty ink containers for temporary storage to avoid accidental spillage.
2. Return empty ink cartridges to a local dealer who can accept such items for collection and
recycling or disposal.
3. If the customer decides to dispose of empty ink cartridges, make sure that they are disposed of
in accordance with local laws and regulations.
4

Symbols and Trademarks
Symbols
Symbol What it means
Bushing
C-ring
Connector
E-ring
FFC (Flexible Film Cable)
Gear
Harness clamp
Hex head screw
Hook (or tab release)
Knob screw (black)
Knob screw (sliver)
Pivot screw
Screw (common screw)
Shoulder screw
Spring x2
Standoff
Stud screw
Timing belt
1

• The notations "SEF" and "LEF" describe how paper is fed from the bypass tray, short edge first or
long edge first.
• "Main Scan" means "horizontal direction", the left to right and right to left movement of the
carriage.
• "Sub Scan" means the "vertical direction", the direction of paper feed.
Trademarks
Adobe is either registered trademarks or trademarks of Adobe Systems Incorporated in the United States
and/or other countries.
Firefox is a registered trademark of the Mozilla Foundation.
Google and Chrome are trademarks of Google Inc.
Microsoft, Windows, and Internet Explorer are either registered trademarks or trademarks of Microsoft
Corporation in the United States and/or other countries.
Safari is a trademark of Apple Inc., registered in the United States and other countries.
The SD is a trademark of SD-3C, LLC.
The proper names of Internet Explorer 8, 9, 10 and 11 are as follows:
• Windows® Internet Explorer® 8
• Windows® Internet Explorer® 9
• Internet Explorer® 10
• Internet Explorer® 11
Other product names used herein are for identification purposes only and might be trademarks of their
respective companies. We disclaim any and all rights to those marks.
2

TABLE OF CONTENTS
Symbols and Trademarks...................................................................................................................................1
Symbols...........................................................................................................................................................1
Trademarks..................................................................................................................................................... 2
1. Product Information
Specifications....................................................................................................................................................25
Main Machine, Peripherals, Options.............................................................................................................26
Model Numbers and Names......................................................................................................................26
Configuration............................................................................................................................................... 27
Guidance for Those Who Are Familiar with Predecessor Products............................................................. 29
Comparison to MP CW2201.....................................................................................................................29
Overview.......................................................................................................................................................... 30
New Features...............................................................................................................................................30
Auto Nozzle Check............................................................................................................................ 30
Carriage Unit.......................................................................................................................................31
Ink Supply Motors...............................................................................................................................32
Carriage LED Lamp.............................................................................................................................33
New Bypass Feed...............................................................................................................................33
Manual Cut..........................................................................................................................................33
Configuration.......................................................................................................................................34
Locations of Major Electrical Components....................................................................................... 35
Smart Operation Panel....................................................................................................................... 36
Roll Paper Setting................................................................................................................................ 38
Acronyms and Important Terms.................................................................................................................. 39
Around the Machine....................................................................................................................................40
Main Sections...............................................................................................................................................50
Main Components....................................................................................................................................... 52
Drive Layout..................................................................................................................................................54
Original Path, Paper Paths.......................................................................................................................... 56
2. Installation
Preparation....................................................................................................................................................... 59
Environment..................................................................................................................................................59
Minimum Space Requirements................................................................................................................... 60
Configuration............................................................................................................................................... 61
3

Machine Level..............................................................................................................................................61
Power Source............................................................................................................................................... 61
Installation Overview...................................................................................................................................62
Installation Flow...................................................................................................................................62
Main Machine Installation...............................................................................................................................64
Before You Begin......................................................................................................................................... 64
Accessory Boxes................................................................................................................................. 64
What You Need..................................................................................................................................65
Accessory List in Box [3].....................................................................................................................65
Accessory List in Box [5].....................................................................................................................67
Main Unit Stand...........................................................................................................................................67
Accessories: Main Unit Stand............................................................................................................ 67
Installing the Main Unit Stand............................................................................................................ 68
Mounting the Main Unit.............................................................................................................................. 70
Assembling the Scanner Stand................................................................................................................... 75
Accessories: Scanner Stand............................................................................................................... 75
Installing the Scanner Stand...............................................................................................................76
Mounting the Scanner Unit......................................................................................................................... 78
Roll Unit 1 (Standard)..................................................................................................................................81
Accessories: Roll Unit 1...................................................................................................................... 81
Installing Roll Unit 1............................................................................................................................ 82
Wiring Roll Unit 1................................................................................................................................88
Roll Unit 2 (Option)......................................................................................................................................91
Accessories.......................................................................................................................................... 92
Installing Roll Unit 2............................................................................................................................ 93
Wiring Roll Unit 2................................................................................................................................96
Controller Options.....................................................................................................................................103
Connecting the Scanner and Main Unit..................................................................................................103
Parts to be Used................................................................................................................................103
Connecting the Harnesses............................................................................................................... 104
Wiring the Scanner Cable............................................................................................................... 106
Clamping the Power Cord............................................................................................................... 111
Removing Tapes and Shipping Materials............................................................................................... 113
4

Original Stacker, Guides..........................................................................................................................115
Installing the Original Stacker, Guides...........................................................................................115
Ink Collector Tank Storage Shelf..............................................................................................................117
Installing the Ink Collector Tank Storage Shelf...............................................................................117
Exit Stacker.................................................................................................................................................119
Accessories: Exit Stacker..................................................................................................................119
Installing the Exit Stacker..................................................................................................................119
Changing the mode of the Paper Exit Stacker................................................................................125
Ink Filling.................................................................................................................................................... 126
Draining and Filling Procedure........................................................................................................126
If Draining Fails to Start.................................................................................................................... 129
Setting Roll Paper...................................................................................................................................... 130
Setting the Paper Spool to Roll Paper............................................................................................. 130
Setting the Paper Roll to the Machine.............................................................................................132
Connecting to the Gigabit Ethernet Interface..........................................................................................135
Check Printing............................................................................................................................................137
Nozzle Check Pattern...................................................................................................................... 137
When an Unbroken Nozzle Check Pattern Cannot be Produced............................................... 139
Halftone Check................................................................................................................................. 139
Final Adjustments.......................................................................................................................................140
Caster Lock........................................................................................................................................140
Level Adjustment............................................................................................................................... 141
Manual Adjust Head Position..........................................................................................................142
Adjust Paper Feed.............................................................................................................................144
Adjust Print Position...........................................................................................................................145
Final Settings..............................................................................................................................................146
After Installation.........................................................................................................................................147
Moving the Machine.................................................................................................................................147
Controller Options......................................................................................................................................... 148
Overview....................................................................................................................................................148
Slots....................................................................................................................................................148
Standard Controller Features.......................................................................................................... 149
SD Card Appli Move................................................................................................................................ 149
5

Overview...........................................................................................................................................149
Move Exec........................................................................................................................................ 149
Undo Exec.........................................................................................................................................150
IEEE 802.11 a/g/n Interface Unit Type M19.......................................................................................151
Included Parts....................................................................................................................................152
Installation......................................................................................................................................... 152
Attaching Antennas...........................................................................................................................153
Checking the Wireless LAN Interface Connection.........................................................................158
OCR Unit Type M13.................................................................................................................................159
Recovery Procedure......................................................................................................................... 162
File Format Converter Type M23 (MLB)................................................................................................. 163
Included Parts....................................................................................................................................163
Installation of MLB............................................................................................................................ 163
Data Overwrite Security Unit Type M19................................................................................................ 165
Overview...........................................................................................................................................165
Before You Begin the Procedure..................................................................................................... 165
Seal Check and Removal.................................................................................................................166
Installation Procedure.......................................................................................................................166
R/W NFC Personal Authentication IC Card ..........................................................................................168
Included Parts....................................................................................................................................168
Installation Guide..............................................................................................................................169
Check All Connections..............................................................................................................................175
Security Setting.............................................................................................................................................. 176
Security Function Installation.................................................................................................................... 176
Data Overwrite Security........................................................................................................................... 177
Before You Begin the Procedure..................................................................................................... 177
Using Auto Erase Memory...............................................................................................................177
HDD Encryption.........................................................................................................................................179
Before You Begin the Procedure:.................................................................................................... 179
Enable Encryption Setting................................................................................................................ 179
Backing Up the Encryption Key.......................................................................................................182
Encryption Key Restoration..............................................................................................................182
@Remote Setting............................................................................................................................................ 185
6

Settings Relevant to the Service Contract................................................................................................ 185
Settings for @Remote Service................................................................................................................... 185
3. Preventive Maintenance
Preventive Maintenance Tables....................................................................................................................191
PM Cleaning Points....................................................................................................................................... 192
PM Table....................................................................................................................................................192
Scanner Unit......................................................................................................................................192
Horizontal Unit..................................................................................................................................195
Waste Ink Collection........................................................................................................................ 199
Other Items for Cleaning.......................................................................................................................... 203
External Covers.................................................................................................................................203
Scanner Unit......................................................................................................................................204
Horizontal Unit..................................................................................................................................206
Paper Feed........................................................................................................................................ 206
Roll Units............................................................................................................................................208
4. Replacement and Adjustment
Notes on the Main Power Switch.................................................................................................................213
Push Switch................................................................................................................................................ 213
Characteristics of the Push Switch (DC Switch).............................................................................. 213
Shutdown Method............................................................................................................................214
Forced Shutdown .............................................................................................................................216
General Precautions......................................................................................................................................217
External Covers..........................................................................................................................................217
Original Transport..................................................................................................................................... 217
Paper.......................................................................................................................................................... 219
Copy Quality............................................................................................................................................. 219
CIS..............................................................................................................................................................220
Electrical Components.............................................................................................................................. 220
Adjustments at Machine Installation........................................................................................................ 220
Other Precautions......................................................................................................................................220
Service Precautions................................................................................................................................... 221
Scanner Unit Rollers......................................................................................................................... 221
Main Frame Screws..........................................................................................................................222
7

Right Plate Screws.............................................................................................................................222
Maintenance Unit Base Screws.......................................................................................................223
Solenoid Bracket Screw...................................................................................................................224
Main Carriage Screws.....................................................................................................................225
Temperature/Humidity Sensor Bracket.......................................................................................... 225
Notes on Operation of the Paper Holding Lever...........................................................................226
Common Procedures..................................................................................................................................... 228
Before You Begin.......................................................................................................................................228
Before Servicing the Machine.................................................................................................................. 229
Rear Output Guides..........................................................................................................................229
Original Guides................................................................................................................................ 230
Original Stacker................................................................................................................................230
Ink Collector Tank.............................................................................................................................232
Paper Rolls.........................................................................................................................................232
Main Covers.............................................................................................................................................. 233
Left Cover.......................................................................................................................................... 234
Right Cover........................................................................................................................................239
Right Upper Cover............................................................................................................................241
Ink Cartridge Cover..........................................................................................................................243
Top Cover..........................................................................................................................................245
Right Rear Cover...............................................................................................................................247
Left Rear Cover................................................................................................................................. 248
Front Cover........................................................................................................................................249
Paper Exit Guide...............................................................................................................................251
Scanner Unit.............................................................................................................................................. 254
Raise the Scanner Unit Fully.............................................................................................................254
Scanner Upper Cover...................................................................................................................... 255
Scanner Rear Cover......................................................................................................................... 260
Scanner Left Cover, Scanner Right Cover...................................................................................... 260
Original Table...................................................................................................................................261
Raise the Left Side of the Scanner Unit............................................................................................262
Raise the Right Side of the Scanner Unit.........................................................................................264
Moving the Carriage Unit.........................................................................................................................267
8

Before You Begin..............................................................................................................................267
Move the Carriage Unit with SP2-102-4.......................................................................................267
Uncapping the Print Heads and Moving the Carriage Unit Manually........................................ 269
Capping the Print Heads Manually.................................................................................................273
Disconnecting the Main Unit from the Scanner Unit...............................................................................274
Disconnecting the Scanner Cable...................................................................................................275
Separating the Main Unit from the Scanner Unit .......................................................................... 278
Operation Panel........................................................................................................................................ 279
Remove..............................................................................................................................................279
Precaution..........................................................................................................................................281
Scanner...........................................................................................................................................................284
Before You Begin.......................................................................................................................................284
Safety Switch Diagram.....................................................................................................................284
Original Width Sensors, Original Set Sensor......................................................................................... 285
Safety Switch............................................................................................................................................. 288
Original Registration Sensor.....................................................................................................................289
Scanner Motor...........................................................................................................................................290
SIB (Scanner I/F Board)...........................................................................................................................292
Remove..............................................................................................................................................292
Precaution..........................................................................................................................................293
Original Feed Roller..................................................................................................................................294
Remove..............................................................................................................................................294
Adjustment.........................................................................................................................................298
Exposure Glass..........................................................................................................................................299
Remove..............................................................................................................................................299
Precaution..........................................................................................................................................300
CIS Unit...................................................................................................................................................... 301
Remove..............................................................................................................................................301
Precaution..........................................................................................................................................303
Adjustment.........................................................................................................................................305
Original Exit Sensor.................................................................................................................................. 305
Original Exit Roller.................................................................................................................................... 306
Remove..............................................................................................................................................306
9

Adjustment.........................................................................................................................................310
White Plate Bracket...................................................................................................................................310
Original Stop Switch................................................................................................................................. 311
Roll Units.........................................................................................................................................................314
Roll Unit 1...................................................................................................................................................314
Remove..............................................................................................................................................314
Precaution..........................................................................................................................................320
Roll Unit 2 (Option)...................................................................................................................................322
Remove..............................................................................................................................................322
Precaution..........................................................................................................................................327
Rewind Switch............................................................................................................................................329
Remove..............................................................................................................................................329
Precaution..........................................................................................................................................330
Left Outer Cover, Left Inner Cover........................................................................................................... 330
Remove..............................................................................................................................................330
Precaution..........................................................................................................................................331
Encoder Sensors........................................................................................................................................332
Remove..............................................................................................................................................332
Cleaning............................................................................................................................................333
Roll Paper Feed Motor..............................................................................................................................334
Roll Paper Feed Clutch..............................................................................................................................336
Remove..............................................................................................................................................336
Precaution..........................................................................................................................................340
Paper Release Sensor............................................................................................................................... 342
Remove..............................................................................................................................................342
Cleaning............................................................................................................................................343
Precaution..........................................................................................................................................344
Feed Roller Housing..................................................................................................................................344
Separate the Feed Roller Housing (Roller Unit 1)..........................................................................345
Separate the Feed Roller Housing (Roller Unit 2)..........................................................................348
Paper Entrance Sensors, Exit Sensor....................................................................................................... 352
Remove..............................................................................................................................................352
Cleaning............................................................................................................................................355
10

Feed Roller.................................................................................................................................................355
Remove..............................................................................................................................................355
Precaution..........................................................................................................................................358
Roll End Sensor..........................................................................................................................................358
Paper Transport..............................................................................................................................................361
Bypass Sensor............................................................................................................................................361
Pre-Registration Sensor............................................................................................................................. 362
Registration End Sensor............................................................................................................................ 363
Paper Transport Fan Motor...................................................................................................................... 364
Paper Exit........................................................................................................................................................366
Cutter.......................................................................................................................................................... 366
Exit Guide...................................................................................................................................................367
Remove..............................................................................................................................................367
Precaution..........................................................................................................................................368
Cutter Unit.................................................................................................................................................. 369
Cutter Switch (Right)..................................................................................................................................372
Cutter Switch (Left).....................................................................................................................................373
Cutter Motor.............................................................................................................................................. 374
Motor Timing Belt, Cutter Belt...................................................................................................................375
Remove..............................................................................................................................................375
Precaution..........................................................................................................................................378
Paper Exit Sensor.......................................................................................................................................379
Guide Plate Safety Sensor........................................................................................................................380
Main Scan......................................................................................................................................................382
Horizontal Encoder Sensor.......................................................................................................................382
Remove..............................................................................................................................................382
Precaution..........................................................................................................................................384
Horizontal Encoder Sheet.........................................................................................................................385
Remove..............................................................................................................................................385
Cleaning............................................................................................................................................388
Precaution..........................................................................................................................................388
Horizontal Motor.......................................................................................................................................389
Horizontal Timing Belt...............................................................................................................................391
11

Sub Scan........................................................................................................................................................ 393
Vertical Encoder Sensor............................................................................................................................393
Precaution..........................................................................................................................................394
Vertical Encoder Wheel, Timing Belt....................................................................................................... 394
Vertical Encoder HP Sensor......................................................................................................................397
Vertical Motor............................................................................................................................................399
Bypass Stopper Clutch Sensor................................................................................................................. 400
Bypass Stopper Clutch..............................................................................................................................402
Carriage Unit................................................................................................................................................. 406
Before You Begin.......................................................................................................................................406
DRESS Sensor............................................................................................................................................407
Remove..............................................................................................................................................408
Cleaning............................................................................................................................................410
Adjustment.........................................................................................................................................411
LED..............................................................................................................................................................414
Remove..............................................................................................................................................414
HRB (Head Relay Board)......................................................................................................................... 416
Remove..............................................................................................................................................416
Precaution..........................................................................................................................................423
Head Lift Motor......................................................................................................................................... 423
Print Head Unit...........................................................................................................................................425
Black Print Head Unit Accessories...................................................................................................426
Color Print Head Unit Accessories.................................................................................................. 427
Carriage Unit Cover Removal......................................................................................................... 427
Black Print Head Unit Removal........................................................................................................429
New Black Print Head Unit Installation...........................................................................................437
Color Print Head Unit Removal........................................................................................................446
New Color Print Head Unit Installation.......................................................................................... 454
After the Print Head Unit Replacement............................................................................................462
Carriage Unit............................................................................................................................................. 465
Remove Ink Supply Unit................................................................................................................... 466
Free the Harness on the Right Side of the Main Unit..................................................................... 469
Main Ink Level Sensor Bracket Removal.........................................................................................474
12

Ink Tube Rail Removal...................................................................................................................... 476
Horizontal Encoder Sheet Removal................................................................................................ 477
Tension Bracket Removal................................................................................................................. 479
Right Plate Removal.......................................................................................................................... 481
Carriage Unit Removal.....................................................................................................................486
Precaution..........................................................................................................................................498
Ink Supply.......................................................................................................................................................504
Ink Supply Unit...........................................................................................................................................504
Ink Supply Unit Accessories.............................................................................................................504
Before You Begin..............................................................................................................................505
Ink Supply Unit Replacement...........................................................................................................505
Carriage Disconnection................................................................................................................... 506
Ink Supply Unit Removal.................................................................................................................. 514
New Ink Supply Unit Installation..................................................................................................... 514
Ink Tube Attachment to the Print Head Unit.................................................................................... 516
Air Release Solenoid.................................................................................................................................521
Ink Level Sensor and Temperature/Humidity Sensor.............................................................................525
Maintenance Unit, Waste Ink Collection.....................................................................................................530
Left Ink Sump..............................................................................................................................................530
Ink Collector Unit.......................................................................................................................................531
Ink Collector Unit Contact Switch............................................................................................................ 532
Right Ink Sump........................................................................................................................................... 533
Maintenance Unit......................................................................................................................................534
Auto-Nozzle Check.......................................................................................................................................538
Auto-Nozzle Check Upper Unit...............................................................................................................538
Auto-Nozzle Check Unit...........................................................................................................................540
After Replacement..................................................................................................................................... 542
Electrical Components...................................................................................................................................544
Rear Cover.................................................................................................................................................544
PCB Box..................................................................................................................................................... 545
Controller Board........................................................................................................................................553
Remove..............................................................................................................................................553
Replacing the NVRAM and Memory..............................................................................................555
13

RFDB (Roll Feeder Drive Board)...............................................................................................................556
Remove..............................................................................................................................................556
IOB (Input/Output Board)....................................................................................................................... 558
Remove..............................................................................................................................................558
HDD............................................................................................................................................................560
Remove..............................................................................................................................................560
Settings.............................................................................................................................................. 561
BiCU (Base image Control Unit).............................................................................................................. 562
Remove..............................................................................................................................................563
EEPROM Replacement.....................................................................................................................564
NVRAM......................................................................................................................................................566
NVRAM on the controller board.....................................................................................................566
NVRAM (EEPROM) on the BiCU.................................................................................................... 568
PSU (Power Supply Unit).......................................................................................................................... 570
Remove..............................................................................................................................................571
Precaution..........................................................................................................................................572
Sensors, Switches.......................................................................................................................................... 573
Ink Collector Tank Cover Switch..............................................................................................................573
Ink-cartridge Cover Switch.......................................................................................................................573
Front Cover Safety Switches.....................................................................................................................574
Front Cover Switch.................................................................................................................................... 575
Remove..............................................................................................................................................575
Precaution..........................................................................................................................................577
Special Adjustments.......................................................................................................................................578
Image Adjustment with SP Modes............................................................................................................578
Step 1: Magnification for Paper Type: Plain.................................................................................. 578
Step 2: Copy/Main Scan Magnification.......................................................................................579
Step 3: Copy/Print Sub Scan Magnification................................................................................. 579
Step 4: Scanner Mask Setting......................................................................................................... 580
Step 5: Erase Margins......................................................................................................................581
Step 6: Printer: Leading Edge, Side-to-Side Registration.............................................................. 581
Step 7: Scanner Mask Setting......................................................................................................... 582
Step 8: Erase Margins......................................................................................................................583
14