Ricoh Y017 Manual

1
Rigel-PJ1Training
Slide 1
Y017/Y018/Y019/Y023
Service Training
Rigel-PJ1 cx/cwH/cwL/cxL
Version 1.0
This training course provides service technician training for the Rigel-PJ1
cx/cwH/cwL/cxL series.

2
Rigel-PJ1Training
Slide 2
Y017/Y018/Y019/Y023
Service Training
Product Overview
This section provides an overview of the machine, and the options that can be
installed.

3
Rigel-PJ1Training
Slide 3
What Models are there in the Series?
Rigel-PJ1 cx (Y017): PJ X5260
4950 lumens, XGA resolution
Rigel-PJ1 cwH (Y018): PJ WX5150
3850 lumens, WXGA resolution
Rigel-PJ1 cwL (Y019): PJ WX5140
3000 lumens, WXGA resolution
Rigel-PJ1 cxL (Y023-21): PJ X5140
3000 lumens, XGA resolution
These are standard models for medium-size class and conference
rooms.
The models in this series cannot be used as network projectors.
Wired LAN capability is only for device management purposes.
» Projector Management Utility: Remote management using PJLink
» Web Control: Management system like Web Image Monitor
@Remote is not supported.
Standard model: Higher than an entry level model but lower than a high-end
model.

4
Rigel-PJ1Training
Slide 4
Main Specifications
3200 lm 4000 lm 3000 lm5000 lm
Brightness (average)
WXGA (1280 x 800)
XGA (1024 x 768)Resolution
Yes (for service purposes only)
8W x 1
300W (251W in Eco
mode)
7.6 kg (16.75 lbs)
398 x 129 x 303.5
300W Mercury lamp
Rigel-PJ1 cx
(Y017) PJ X5260
HDMI
USB
Wired LAN
Wireless LAN
Speaker
Power Consumption
Weight
Dimensions (W×D×H)
Projection Distance
Projection Screen Size
Keystone
Lamp type
Type
Yes
For control purposes only (PJLink)
No
5W x 1
300W (230W in Eco
mode)
230W (190W in Eco mode)
3 kg (6.6 lbs)
306 ×238 ×97
1.2 - 10m (3.28 to 32.8 ft)
32 ” - 307 ” (81.3 – 780 cm)
Vertical, adjustable by user
300W Mercury lamp
230W Mercury lamp
DLP
Rigel-PJ1 cwH
(Y018) PJ WX5150
Rigel-PJ1 cwL
(Y019) PJ WX5140
Rigel-PJ1 cxL
(Y023-21) PJ X5140
See the specifications table in the service manual for more details.

5
Rigel-PJ1Training
Slide 5
Features
This product can be installed by users, except
when mounted on a ceiling.
Almost all service parts can be replaced as
units/assemblies.
No special facilities are required to replace parts.
There is no operation panel, but LEDs show the
symptoms for troubleshooting (blinking/lit,
number of times the LEDs blink, etc).
A service mode is available.
No additional notes

6
Rigel-PJ1Training
Slide 6
Consumables and Options
Replacement lamp
Rigel-P1 cx
» 300W mercury lamp (Y208): Type 8
» Life: 2500 hours (normal mode), 3500 hours (Eco mode)
Rigel-PJ1 cwH
» 300W mercury lamp (Y205): Type 5
» Life: 2500 hours (normal mode), 3500 hours (Eco mode)
Rigel-PJ1 cwL/cxL
» 230W mercury lamp (Y206): Type 4
» Life: 2500 hours (normal mode), 4000 hours (Eco mode)
The lamp is regarded as having reached its yield when its
maximum brightness has decreased to 50% of the original
level.
When this occurs, a message to this effect is projected.
3D glasses (Y107)
DLP link is a technology that allows DLP projectors to
transmit 3D data.
DLP link technology sends data seamlessly to the glasses
between frames to create a 3D image.
For more about DLP link: http://www.dlp.com/projector/dlp-innovations/dlp-
link.aspx

7
Rigel-PJ1Training
Slide 7
Reliability Information
Average monthly projection time: 55.0 hrs/month
2.50 hrs/day x 22 working days/month
Failure Rate
1st year: 0.00254 cases/unit/month
2nd year: 0.00302 cases/unit/month
3rd year: 0.00382 cases/unit/month
The failure rate of a projector increases with its
total power-up time. This is due in part to the
failure characteristics of optical engines in
projectors.
No additional notes

8
Rigel-PJ1Training
Slide 8
Lamp Near-end/End Alerts
There is no near-end alert.
The lamp end alert occurs when the machine
calculates that the life time has expired.
If used in Normal Mode only, the alert appears
after 2,500 hrs projection time
If used in Eco Mode only, the alert appears after
4,000 hrs projection time (3,500 hrs for cwH and
cx)
If the user switches between modes, the machine
calculates when to display the alert based on
how long the lamp was used in each mode.
No additional notes

9
Rigel-PJ1Training
Slide 9
Disposal of Broken Lamps
Projector lamps normally contain mercury
vapour.
These lamps can rupture due to impact or being
used longer than their life expectancy.
The time that the breakage will occur differs
widely for each lamp and its circumstances of
use.
These lamps must be disposed of in accordance
with local environmental regulations.
No additional notes

10
Rigel-PJ1Training
10
Slide 10 10
Overview Appearance (Y017)
External View
1. Control panel
2. Lamp cover
3. Zoom lever
4. Ventilation (inlet)
5. Speaker
6. Focus ring
7. Ventilation (outlet)
8. Remote sensor
9. Lens cap
10. Lens
11. Connection ports
12. Adjustable feet
13. Filter
Slide 10 10
Overview Appearance (Y017)
External View
1. Control panel
2. Lamp cover
3. Zoom lever
4. Ventilation (inlet)
5. Speaker
6. Focus ring
7. Ventilation (outlet)
8. Remote sensor
9. Lens cap
10. Lens
11. Connection ports
12. Adjustable feet
13. Filter
Filter
A filter will be provided for the China versions of the other models (Y018, Y019,
Y023). Installation will be explained in a technical bulletin.

11
Rigel-PJ1Training
Slide 11
Appearance (Y017)
Operation Panel
The three LEDs (power,
lamp, temp) are used to
show symptoms for
troubleshooting.
Remote
Controller
1. Power and Power indicator: Indicates the projector’s power status.
2. Lamp indicator: Indicates the projector’s lamp status.
3. Temp indicator: Indicates the status of the projector’s interior temperature.
4. Volume -: Decreases speaker volume.
5. Keystone: Use to adjust the image to compensate for distortion caused by
tilting the projector.
6. Enter: Select or confirm settings.
7. Volume +: Increases speaker volume.
8. Four Directional Select Keys: Use to select items or make adjustments to your
selection.
9. Menu: Press “Menu” to launch the Onscreen display (OSD), or to go back to
the previous menu.
10. Input: Switch between Computer1, Computer2 , Component, Video, S-Video,
DVI, and HDMI.
11. AV Mute: Momentarily turn the audio and video off/on.
Maximum operating range for the remote control is about 23.0’ (7m) and 15°in
front of the projector.

12
Rigel-PJ1Training
12
Slide 12 12
9Interface
Overview Appearance (Y017)
Connection Ports
1. LAN terminal: Use this port for settings via the network.
2. DVI terminal
3. HDMI terminal: Input for digital signals from a HDMI (High-Definition
Multimedia Interface) compatible digital source.
4. COMPUTER 1 IN terminal: Input for analog RGB signals from a computer or a
component video signal (Y/PB/PR) from video equipment.
5. MONITOR OUT terminal: Output for analog RGB signals or component video
signal (Y/PB/PR) to another device.
6. S-VIDEO IN terminal: Input for S video signals from video equipment.
7. Component IN terminal: Y/PB/PR terminals (from left to right)
8. Service Port: Use this port to update the firmware.
9. AC IN socket: Connect the supplied power cord.
10. COMPUTER 2 IN terminal
11. PC CONTROL terminal (RS232 Compliant)
12. VIDEO IN terminal: Input for video signals from video equipment.
13. AUDIO IN terminal (from left to right): Input for audio signals from a computer
or video equipment.
¾(1) For S-VIDEO and VIDEO
¾(2) For COMPUTER1, COMPUTER2, and DVI
¾(3) For COMPONENT AUDIO-OUT terminal
14. AUDIO-OUT terminal
15. Anti-theft lock hole (Kensington™ Lock)

13
Rigel-PJ1Training
13
Slide 13 13
Overview
Appearance (Y018/Y019/Y023)
External View
1. Control panel
2. Zoom ring
3. Ventilation (inlet)
4. Focus ring
5. Ventilation (outlet)
6. Remote sensor
7. Lens
8. Lens cap
9. Connection ports
10.Speaker
11.Adjustable feet
Slide 13 13
Overview
Appearance (Y018/Y019/Y023)
External View
1. Control panel
2. Zoom ring
3. Ventilation (inlet)
4. Focus ring
5. Ventilation (outlet)
6. Remote sensor
7. Lens
8. Lens cap
9. Connection ports
10.Speaker
11.Adjustable feet
No additional notes

14
Rigel-PJ1Training
Slide 14
Appearance (Y018/Y019/Y023)
Operation Panel
The three LEDs (power,
lamp, temp) are used to
show symptoms for
troubleshooting.
Remote
Controller
1. Lamp indicator: Indicates the projector’s lamp status.
2. Temp indicator: Indicates the projector’s temperature status.
3. Power indicator: Indicates the projector’s status.
4. Power: Turns the power on/off
5. Volume -: Decreases the speaker volume.
6. Input: Press “Input” to choose from the RGB, Component, S-Video, HDMI and
Composite sources.
7. Menu: Press “Menu” to launch the Onscreen display (OSD), or to go back to
the OSD main menu.
8. Enter: Use this to confirm your section of items in a menu.
9. Volume +: Increases the speaker volume.
10. Mute: Turns the audio and video off/on.
11. Four Directional Select Keys: Use to select items or make adjustments to
your selection.
12. Keystone Adjustment: Use to adjust the image to compensate for distortion
caused by tilting the projector.
Maximum operating range for the remote control is about 23.0’ (7m) and 30°in
front of the projector.

15
Rigel-PJ1Training
15
Slide 15 15
9Interface
Overview
Appearance (Y018/Y019/Y023)
Connection Ports
1. LAN terminal: Use this port for settings via the network.
2. SERVICE Port: Use this port to update the firmware.
3. HDMI terminal: Input for digital signals from a HDMI (High-Definition
Multimedia Interface) compatible digital source.
4. COMPUTER 1 IN terminal: Input for analog RGB signals from a computer or a
component video signal (Y/PB/PR) from video equipment.
5. MONITOR OUT terminal: Output for analog RGB signals or component video
signal (Y/PB/PR) to another device.
6. S-VIDEO IN terminal: Input for S video signals from video equipment.
7. VIDEO IN terminal: Input for video signals from video equipment.
8. AUDIO IN2 terminal (For COMPUTER IN2): Input for audio signals from a
computer or video equipment.
9. AUDIO OUT terminal
10. AC IN socket: Connect the supplied power cord.
11. COMPUTER 2 IN terminal
12. PC Control terminal (RS232 compliant)
13. AUDIO IN2 terminal (For VIDEO and S-VIDEO)
14. Anti-theft lock hole
15. AUDIO IN1 terminal (For COMPUTER 1 IN): Input for audio signals from a
computer or video equipment.

16
Rigel-PJ1Training
Slide 16
How to Use the Connection Ports - 1
1. Power cord (supplied)
2. LAN cable
3. USB cable
4. HDMI/DVI cable
5. RGB cable (supplied)
6. Audio out cable jack to jack
7. Audio in cable jack to jack
8. Monitor out cable

17
Rigel-PJ1Training
Slide 17
How to Use the Connection Ports - 2
1. Power cord (supplied)
2. LAN cable
3. COMPONENT-RGB Cable
4. 3 RCA Component Cable
5. Composite video cable
6. Audio in cable jack to jack
7. S-Video cable
8. Audio out cable jack to jack
9. HDMI cable

18
Rigel-PJ1Training
Slide 18
Turning Power On
Turn the projector on first, then the signal
sources.
No additional notes

19
Rigel-PJ1Training
Slide 19
Turning Power Off
Press the “Power” button to turn off the projector
lamp. When you see a message on the display,
press the “Power” button again to confirm.
The cooling fan continues to operate for about 60
seconds for cooling cycle and the Power
indicator will flash red. When the light stops
flashing, the projector has entered standby
mode.
If you wish to turn the projector back on, you must
wait until the projector has completed the cooling
cycle and has entered standby mode. Once in
standby mode, simply press “Power” to restart the
projector.
Disconnect the power cord.
No additional notes

20
Rigel-PJ1Training
Slide 20
Warning Indicators
When the “Temp” indicator lights red, and
‘Temperature Error’ appears, the projector has
overheated. The projector will automatically shut
itself down.
When the “Temp” indicator flashes red (0.5 sec
on, 0.5 sec off) and ‘Fan Error’ appears on-
screen, the fan failed. Stop using the projector
and disconnect the power cord from the
electrical outlet.
No additional notes