Rightest GT100 User manual

1
3
23 11 2 3
Front View of Meter Back View of Meter
UP BUTTON
DOWN BUTTON
MAIN BUTTON
( )
DISPLAY WINDOW
Shows test results,
messages and
relative information.
TEST STRIP PORT
Insert test strip here
until you hear a click.
METER LABEL
BATTERY
COVER
Slide cover to
change batteries.
Test strips vial Lancing Device
Lancet
Test strips
Sample Entry
View Window
Protective cover
PlungerHubLancet carrier
Release button
Safe switch
Depth adjustable cap
1) Turn the meter over. Press and push battery cover to open.
2) Install the battery. Be sure to put battery in correct direction.
3) Slide the battery cover back until it snaps into place.
2
1) Press and release main button " " to turn on the meter.
2) Press and hold main button " " for 7 seconds to activate the setting mode. The year will flash.
(NOTE: Prior to setting mode, the meter will turn off. Main button must remain pressed to access
setting mode.)
3) Press up button or down button to change the year.
4) Press main button " " to confirm the year and move to month setting.
5) Repeat steps 3 and 4 to change the date, time format, hour, minute volume and unit of
measurement. After pressing the main button to confirm the minute setting, your set-up is
finished.
NOTE
- In order to ensure proper operation, do not to use this meter close to sources of strong
electromagnetic radiation.
- Keep meter free of dust and liquids including water.
1) Hold the depth adjustable cap in one hand and hold the hub in the other hand. Bend the cap
towards the down side, until a gap appears between the cap and hub.
2) Pull the cap and hub off in opposite directions, remove the cap.
3) Insert a new disposable lancet firmly into lancet carrier.
GT100 Blood Glucose Monitoring System GETTING STARTED GUIDE (For self-testing and professional use)
TM
Battery Installation
Setting Up Your Meter - Setting the Date, Volume and Time
Preparing the Lancing Device
Clear Cap
Control Solution

4) Sample Size Example
4
101-3GM555-XXX EN
Bionime GmbH
Tramstrasse 16
9442 Berneck
Switzerland
Email: [email protected] 0197
4
0.75 µL 1.0 µL 1.5 µL 2.0 µL 3.0 µL
13 2
8
12
9 10 11
5
4) Twist off and set aside the protective cover of the disposable lancet.
5) Replace the depth adjustable cap.
6) Choose a depth of penetration by rotating the top portion of the depth adjustable cap until your
desired setting depth is visible in the window. Settings are based on skin type:
" " for soft or thin skin;
" " for average skin;
" " for thick or calloused skin.
7) Hold the hub in one hand and pull on the plunger with the other hand. The device will be cocked.
Release the plunger and it will automatically move back to its original position near the hub.
4675
1) Wash and dry your hands. Take one strip from the vial. Close the vial cap immediately.
2) Insert the strip into the strip port on the meter with the indication symbol facing up. Push the strip in
until it clicks and stops. The meter will automatically detect the code number.
3) When you see the flashing blood drop icon on the display window, hold the lancing device to the
side of your fingertip and press the release button.
4) The meter only requires a small blood sample. A minimum of 0.75 µL of blood is needed to test.
Blood sample size above 3.0 µL might contaminate the meter. Not enough blood (<0.75 µL) might
cause inaccurate results.
5) Touch and hold the drop to the edge of sample entry until you hear a "beep" and the view window is filled
with blood. If the view window is not completely filled with blood the test will not start. Discard the test
strip and repeat the test with a new test strip.
6) The countdown mode will begin on the display window. After 5 seconds, your test result will appear. For
more information about your test results, please see your User Manual.
For more information on how to use your meter and understand your test results, please see the
User’s Manual.
Alternative site testing: palm or forearm blood sampling
1. Choose the clear cap and follow step 1 through step 3
"Performing a Test".
2. Massage the puncture area of your palm or forearm for a few
seconds.
3. Immediately after massaging the puncture area, press and
hold the lancing device with the clear cap against your palm or
forearm.
4. Press the release button.
5. Continue holding the lancing device against your palm or
forearm and gradually increase pressure for a few seconds
until the blood sample size is sufficient.
6. Follow step 8 to discard the used disposable lancet.
Releasing
button
7) Remove the test strip from the meter. Please follow your local regulations to discard the used strip
properly.
8) Pull off the depth adjustable cap. Without touching the used disposable lancet, insert the lancet tip into
the protective cover.
9) Hold the release button in one hand and pull on the plunger with the other hand to safely eject the used
disposable lancet.
10) Discard the used disposable lancet into an appropriate puncture-proof or biohazard container.
11) Replace the depth adjustable cap after finishing the test.
3a 3b
45
7
BIONIME CORPORATION
No. 100, Sec. 2, Daqing St., South Dist.,
Taichung City 40242, Taiwan
Tel: [phone]
Fax: [phone]
http: //www.bionime.com
E-mail: [email protected]
6
Rotate
Performing a Test
Pressing for
a few seconds
Palm
Forearm
Rev. Date: 2019-10