Rightest GT333 User manual

Test strips vial Lancing Device
Lancet
Front View of Meter Back View of Meter
Test strips
Sample Entry
View Window
Protective cover
Lancet carrier
Release button
Depth adjustable cap
2
3Setting Up Your Meter - Setting the Date, Time , Volume and Measurement Unit
3
Test Strip Port
Display Window
Left Button ( ) Right Button ( )
Main Button ( )
Battery Cover
Installing the Batteries
1) Turn the meter over. Press and slide battery cover to open.
2) Install the 2 AAA batteries. Be sure to insert the batteries in the correct direction.
3) Slide the battery cover back on until it snaps into place.
1) Press and release the Main button " " to turn on the meter.
2) Press and hold the Main button " " for 7 seconds to enter the Setting Mode. The year will flash.
(Note: The meter will turn off while you are holding down the button. Continue holding down the Main
button to reach the Setting Mode. You will then be asked to set the year.)
21
PlungerHub
Safe switch
Meter label
Clear Cap
Control Solution
GT333 Blood Glucose Monitoring System GETTING STARTED GUIDE (For self-testing and professional use)
4Preparing the Lancing Device
5) Repeat step 3 and 4 to change the date, time format, hour, minute, volume and unit. After
pressing the main button to confirm the volume setting, your set-up is complete.
1 2 3
1) Hold the depth adjustable cap in one hand and hold the hub in the other hand. Bend the cap towards the down
side, until a gap appears between the cap and hub.
2) Pull the cap and hub off in opposite directions, remove the cap.
3) Insert a new disposable lancet firmly into the lancet carrier.
4) Twist off and set aside the protective cover of the disposable lancet.
5) Replace the depth adjustable cap.
6) Choose a depth of penetration by rotating the top portion of the depth adjustable cap until the setting depth
matches the window. Settings are based on skin type
" " for soft or thin skin;
" " for average skin;
" " for thick or calloused skin.
7) Hold the hub in one hand and pull on the plunger in the other hand. The device will be cocked. Release the
plunger, it will automatically move back to its original position near the hub.
46 7
5
3) Press the Left button " " or Right button " " to change the year.
4) Press the Main button " " to confirm the year and move onto the month setting.
NOTE
- Suggest not to use this meter close to source of strong electromagnetic radiation, to avoid interference with
proper operation.
TM
Test Strips
2℃
30℃
0197

12
Performing a Test
5
1 2
1) Wash and dry your hands. Take one test strip from the vial. Close the vial cap immediately.
2) Insert the test strip into the strip port on the meter with the view window facing up. Push the test strip in until you hear
a click. The meter will automatically detect the code number.
3) When you see the flashing blood drop icon on the display window, hold the lancing device to your fingertip and press
the release button.
4) Sample Size Example
4) A blood drop size between 0.75 µL and 3.0 µL is required for testing. See Sample Size Example Chart for drop sizes.
Blood drop sizes greater than 3.0 µL may contaminate the meter. A minimum of a 0.75 µL drop is required for
accurate results.
0.75 µL 1.0 µL 1.5 µL 2.0 µL 3.0 µL
5) Touch and hold the drop to the edge of sample port until you hear a " beep " and the view window is filled with blood.
If the view window is not completely filled with blood, the test will not start. Discard the test strip and repeat the test
with a new test strip.
6) The countdown will begin on the display window. After 5 seconds, your test result will appear. For more information
about your test results, please see your User’s Manual.
7) Rotate the test strip counterclockwise and pull up simultaneously to remove the test strip from the meter. Please
follow your local regulations to properly discard the used test strip.
8) Pull off the adjustable depth cap. Without touching the used disposable lancet, stick the lancet tip into the protective
cover.
9) Hold the release button in one hand and pull the plunger with the other hand. This will safely eject the used
disposable lancet.
10) Discard the used disposable lancet into an appropriate puncture-proof or biohazard container.
11) Replace the adjustable depth cap after finishing the test.
5a 7
6
5b
Alternative site testing: palm or forearm blood sampling
1. Choose the clear cap and follow step 1 to 5 of the above section "
Performing a Test ".
2. Massage the puncture area of your palm or forearm for a few
seconds.
3. Immediately after massaging the puncture area, press and hold
the lancing device with the clear cap against your palm or forearm.
4. Press the release button.
5. Continue holding the lancing device against your palm or forearm.
Gradually increase pressure for a few seconds until the blood
sample size is sufficient.
6. Follow step 9 of the above section to discard the used disposable
lancet.
NOTE: DO NOT test on the palm or forearm if you are testing for
hypoglycemia (low blood glucose).
3a
3b
8
Releasing
button
Pressing for
a few seconds
For more information on how to use your meter and understanding your test results, please see your GT333 Blood
Glucose Monitoring System User's Manual.
45
9 10
Rev. Date:2019-10
101-3GM236-XXX EN
BIONIME CORPORATION
No. 100, Sec. 2, Daqing St., South Dist.,
Taichung City 40242, Taiwan (R.O.C)
Tel: [phone]
Fax: [phone]
E-mail: [e-mail]
http://www.bionime.com
Bionime GmbH
Tramstrasse 16, 9442 Berneck, Switzerland
E-mail: [email protected] 0197
Rotate
Palm
Forearm