Rimage Everest 600 User manual

EverestTM III Printer
EverestTM 600 Printer

2000621_B
Corporate Headquarters:
Rimage Corporation
7725 Washington Avenue South
Minneapolis, MN 55439
USA
800-553-8312 (toll free US)
Service: [phone] (Asia/Pacic, Mexico/Latin
America)
Fax: [phone]
European Headquarters:
Rimage Europe GmbH
Albert-Einstein-Str. 26
63128 Dietzenbach
Germany
Tel: [phone]
Fax: [phone]
Rimage Corporation reserves the right to make
improvements to the equipment and software described in
this document at any time without any prior notice. Rimage
Corporation reserves the right to revise this publication and
to make changes from time to time in the content hereof
without obligation of Rimage Corporation to notify any
person or organization of such revisions or changes.
This document may contain links to web sites that were
current at the time of publication, but may have moved or
become inactive since. This document may contain links
to sites on the Internet that are owned and operated by
third parties. Rimage Corporation is not responsible for the
content of any such third-party site.
©2009, Rimage Corporation
Rimage®is a registered trademark of the Rimage
Corporation. Rimage Everest™ is a trademark of the
Rimage Corporation. Dell™ is trademark of Dell Computer
Corporation. FireWire™ is a trademark of Apple Computer,
Inc. Windows®is a registered trademark of Microsoft
Corporation.
All other trademarks and registered trademarks are the
property of their respective owners.
2000621_B

2000621_B
Contents
Introduction..............................................................................................................................................................1
About this User Guide................................................................................................................................................................1
Unpacking and Setup Instructions .............................................................................................................................................1
Important Information .............................................................................................................................................3
Support Information ...................................................................................................................................................................3
Learn More Online .....................................................................................................................................................................3
Technical Support ......................................................................................................................................................................3
Optical Disc Recording Software Disclaimer .............................................................................................................................4
Safety and Compliance Information...........................................................................................................................................4
Safety Precautions ......................................................................................................................................................................................... 4
Compliance Information ................................................................................................................................................................................. 5
Rimage Everest 600 and Everest III Printer Specications ....................................................................................................... 6
Printer Requirements..............................................................................................................................................9
Ribbon Requirements ................................................................................................................................................................9
Everest 600 Ribbons...................................................................................................................................................................................... 9
Everest III Ribbons......................................................................................................................................................................................... 9
Label Design Requirements.....................................................................................................................................................10
Print Requirements ..................................................................................................................................................................10
Identify the Parts of the Everest Printer.............................................................................................................. 11
Front View ............................................................................................................................................................................... 11
Control Panel ...........................................................................................................................................................................12
Control Panel Indicators............................................................................................................................................................................... 12
Back View ................................................................................................................................................................................13
Switches...................................................................................................................................................................................14
Mode Switch................................................................................................................................................................................................. 14
AC Voltage Switch........................................................................................................................................................................................ 14
Operate the Everest Printer..................................................................................................................................15
Power On and Off the Everest Printer ..................................................................................................................................... 15
Power On or Off a Standalone Printer.......................................................................................................................................................... 15
Power On or Off a Printer Connected to an Autoloader or AutoPrinter ........................................................................................................ 15
Place a Disc on the Printer Tray ..............................................................................................................................................15
Set Your Printing Preferences..............................................................................................................................17
Set Your Printing Preferences on a Windows PC ....................................................................................................................17
Access Printing Preferences (PC)................................................................................................................................................................ 17
Access Printing Preferences through the Windows Start Menu............................................................................................................... 17
Access Printer Preferences through CD Designer................................................................................................................................... 17
Access Printer Preferences when Printing PDFs..................................................................................................................................... 17
Set the Media Type, Media Size, Orientation and Ribbon Type (PC)........................................................................................................... 18
Set the Print Quality, Color Matching and Image Adjustments (PC) ............................................................................................................ 18
Set the Printable Area (PC) .......................................................................................................................................................................... 19
Adjust the Print Alignment and Color Density (PC) ...................................................................................................................................... 20
Set Your Printing Preferences on a Macintosh ........................................................................................................................ 21
Access Printing Preferences (Macintosh) .................................................................................................................................................... 21
Set the Media Type, Ribbon Type and Print Quality (Macintosh)................................................................................................................. 21
Set the Color Matching and Image Adjustments (Macintosh) ...................................................................................................................... 21
Set the Printable Area (Macintosh)............................................................................................................................................................... 22
Adjust the Print Alignment and Color Density (Macintosh)........................................................................................................................... 22
Check the Ribbon Remaining ..................................................................................................................................................23
View the Ribbon Status (PC)........................................................................................................................................................................ 23
View the Ribbon Status (Macintosh) ............................................................................................................................................................ 24
Maintain the Everest Printer.................................................................................................................................25
Maintenance Schedule ............................................................................................................................................................25
Change the Print Ribbon..........................................................................................................................................................25
Remove the Print Ribbon ............................................................................................................................................................................. 26
Install the Print Ribbon ................................................................................................................................................................................. 27

2000621_B
Rimage Everest™ III and 600 User Guide
Change the Retransfer Ribbon ................................................................................................................................................28
Remove the Retransfer Ribbon.................................................................................................................................................................... 28
Install the Retransfer Ribbon........................................................................................................................................................................ 29
Clean the Everest Printer.........................................................................................................................................................30
Clean the Print Head.................................................................................................................................................................................... 30
Clean the Tacky Rollers................................................................................................................................................................................ 31
Clean the Rear Air Filter ............................................................................................................................................................................... 32
Clean the Side Air Filters (Everest 600 only)................................................................................................................................................ 32
Clean the Platen Roller ................................................................................................................................................................................ 34

12000621_B
Introduction
This manual provides the information needed to operate, congure, and maintain the Rimage Everest™ 600 or Rimage
Everest™ III printer. The information included in this manual and the term “Everest” apply to both the Everest 600 and the
Everest III printers, except when noted otherwise.
Note: Your Everest printer may not look exactly like the model featured in this user guide.
About this User Guide
• While we try to maintain all versions of our manuals and documentations, please note that the English version found on
our web site always contains the most up-to-date information.
• Unless otherwise indicated, all Windows navigation statements are Windows XP paths. Windows Vista, Windows 2000,
and Windows Server 2003 navigation may differ slightly.
• These symbols are used throughout the manual to help clarify information:
Note: A Note provides supplemental information or information that may apply only in special cases. For example,
memory limitations, equipment congurations, or details that apply to specic versions of a program would be
included in a Note.
Tip: A Tip provides techniques and procedures to help with your specic needs. A Tip suggests alternative methods
that may not be obvious and helps you understand the benets and capabilities of the product.
-Important! An Important note provides information essential to the completion of a task. You can disregard
information in a Note or Tip and still complete a task, but do not disregard an Important note.
Caution: A Caution indicates that failure to observe this guideline could result in loss or damage to the equipment,
product, software, or data.
 Warning! A Warning indicates situations that failure to follow this guideline could result in bodily injury to personnel
operating or maintaining the equipment.
Unpacking and Setup Instructions
To unpack your Everest printer, refer to the unpacking label on the Everest printer box. To set up and install your Everest
printer, refer to the Rimage Everest III and 600 Setup and Installation Guide, as well as the setup and installation guide
included with your Rimage product.

32000621_B
Important Information
Important Information
This section provides support contact information, cautions and warnings, and product specications for the Rimage Everest
printer.
Support Information
US, Asia/Pacic, Mexico/Latin America Europe
Rimage Corporation
7725 Washington Avenue South
Minneapolis, MN 55439
USA
Attn: Rimage Services
Rimage Europe GmbH
Albert-Einstein-Str. 26
63128 Dietzenbach Germany
Contact Rimage Services:
Website: www.rimage.com/support
KnowledgeBase: http://rimage.custhelp.com
Log in and select the Ask a Question tab
Telephone:
North America: 800-553-8312
Asia/Pacic, Mexico/Latin America: 952-946-0004
Fax: [phone]
Contact Rimage Services Europe:
Website: www.rimage.de
Email: [email protected]
Telephone: [phone]
Fax: [phone]
When you contact Rimage Services, please provide:
• System serial number and software version
• Functional and technical description of the problem
• Exact error message received
My Rimage Product Information:
Copy this information from your Rimage Product for future
reference.
Note: Make sure you update the Serial Number here
anytime you receive a replacement autoloader.
Serial Number:
Product Name:
Date of Purchase:
Learn More Online
At www.rimage.com/support, you can experience Rimage’s world-class Support and Services.
From the Support home page:
1. Select your product series.
2. Select your product.
3. Learn more on the product page.
From your product page you can access:
• Information about the latest software and rmware
updates
• Product specications
• The latest documents
• Current rmware and driver downloads
Technical Support
Support for the Everest Printer is available through your authorized reseller.
-Important! Make sure that you register your Everest printer so Rimage can notify you of upgrades as they become
available.

4 2000621_B
Rimage Everest™ III and 600 User Guide
Optical Disc Recording Software Disclaimer
This Product, Software, or Documentation may be designed to assist you in reproducing material in which you own the
copyright or have obtained permission to copy from the copyright owner. Unless you own the copyright or have permission to
copy from the copyright owner, you may be violating copyright law and be subject to payment of damages and other remedies.
If you are uncertain about your rights, you should contact your legal advisor. If you are neither in possession of the copyright
nor have authorization from the owner of the copyright, unauthorized copying of copyrighted material on an optical disc or any
other media violates national and international legislation and can result in severe penalties.
Safety and Compliance Information
This manual and the indications on the product allow proper and safe operation. The indication marks below help protect you
and other persons from injury, and equipment from damage.
 Warning! According to ANSI (American National Standards Institute) standards, a warning is used to indicate situations
that could result in bodily injury to personnel operating or maintaining the equipment.
Caution: Indicates that failure to observe this guideline could result in loss or damage to the equipment, product,
software, or data.
Safety Precautions
To ensure safety, read these precautions and familiarize yourself with their meaning before using the equipment.
 Warning!
• Useofcontrolsoradjustmentsorperformanceofproceduresotherthanthosespeciedhereinmayresultin
hazardous radiant exposure.
• Do not disassemble or use tools on the printer. All service procedures should be performed by a Rimage-authorized
technician, or sent in for Rimage-authorized repair.
• Do not service the printer with the power cord plugged in the AC outlet.
• The interior of the printer contains sharp edges.
• Thefrontbezeloftheprintercanbeopenedbyhand.Donotinsertyourngers.
• Do not touch the heat roller.
Caution:
• All equipment with AC line voltage, or low DC voltages, such as switches, power supplies, fuses, fans, and non-
stepper motors, must be replaced with Rimage-approved components to maintain the safety approval issued by UL.
• Use only the supplied AC power cord. Fore more information or to order a new power cord, contact Rimage Customer
Service.
• Thisproductisdesignedforanofceenvironment.
• Donotusetheprinterifitisoverheatingoranabnormalsmellisdetected.Thismayresultinareandanelectric
shock. In case of heating or abnormal smell, immediately disconnect the cable from the outlet. Contact your Rimage-
authorized dealer for repairs.
• Allowsufcientfreespaceforopeningtheprintertray.Donottouchtheprintertraywhileitisinmotion.
• If the side cover is opened while power is supplied, the printer will stop. Do not reach into the printer while it is in
operation. Do not attempt to bypass the door interlock.
• This printer has no power switch. Power is disconnected completely by unplugging the cable. Rimage recommends
installing the printer in a position that allows immediate disconnection of the power cable. Always hold the plug when
disconnecting the cable from the outlet.
• This printer has a voltage slide switch on the back of the unit. Before use, check that is set to the correct voltage.
Pleasedonotuseanyvoltageotherthan110VACor220VAC.Thiscouldresultinareandanelectricshock.
Country-specic cautions for Wideband Data Transmission systems: 2400-2483.5 MHz
• France: Do not use outdoors.
• Italy: If used outside of own premises, general authorization is required.
• Norway: This subsection does not apply for the geographical area within a radius of 20km from the center of NY-
Alesund.

52000621_B
Important Information
Compliance Information
Product Name Rimage Everest Printer
Model CDPR22 (Everest III)
CDPR23 (Everest 600)
Notice for USA NOTE: This equipment has been tested and found to comply with the limits for
a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when this
equipment is operated in a commercial environment. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to cause
harmful interference, in which case the user will be required to correct the interference
at his own expense.
This product complies with UL 60950-1, 1st edition.
Notice for Canada This Class A digital apparatus complies with Canadian ICES-003 Issue 4:2004. Cet
appareil numerigue de la classe A est conforme a la norme NMB-003 du Canade.
This product complies with CAN/CSA-C22.2 No. 60950-1-03 1st edition.
Notice for Europe This product is in conformity with the EMC Directive (89/336/EEC) and the Low-
Voltage Directive (73/23/EEC) through compliance with the following European
standards: EN 55022: 1998 + Amd 1: 2000 Class B Limit; EN 55024: 1998; EN 61000-
3-2:2000; EN 61000-3-3:1995 + Amd 1: 2001; EN 60950: 2000. The CE mark has
been afxed in accordance with the CE Marking Directive 93/68/EEC.
Notice for Japan This is a Class A product based on the standard of the Voluntary Control Council for
Interference by Information Technology Equipment (VCCI). If this equipment is used in
a domestic environment, radio interference may occur, in which case, the user may be
required to take corrective action.
Translation:
この装置は、情報処理装置等電波障害自主規制協議会（ＶＣＣＩ）の基準に基づくクラス
A 情報技術装置です。この装置を家庭環境で使用すると電波妨害を引き起こすことがあり
ま
す。この場合には使用者が適切な対策を講ずるよう要求されることがあります。
Notice for Australia This product complies with AS/NZS CISPR22:2004.

6 2000621_B
Rimage Everest™ III and 600 User Guide
Everest 600 Everest III
Printing Speed*
(For CMY color coverage)
*The rst print takes 5 minutes, which
includes warm-up time.
60 seconds or less Normal mode: 60 seconds
Best mode: 78 seconds
Printing Modes Monochrome and CMY Monochrome, CMY, and CMY+W
Print Quality Equivalent of 600 pixels per inch. Equivalent of 300 pixels per inch.
Media
Requirements
Use Rimage Media Kits™ for optimum
recording and print performance.
Use Rimage Media Kits™ for optimum
recording and print performance.
Print Ribbon
Requirements
Monochrome (Black)
CMY (Cyan, Magenta, and Yellow)
Monochrome (Black)
CMY (Cyan, Magenta, and Yellow)
CMY+W (Cyan, Magenta, Yellow, and
White)
Ribbon Capacity Monochrome Ribbon: 1000 discs
CMY Ribbon: 500 discs
Retransfer Ribbon: 1000 discs
Monochrome ribbon: 1000 discs
CMY Ribbon: 500 discs
CMY+W Ribbon: 375 discs
Retransfer Ribbon (standard): 1000
discs
Retransfer Ribbon (optional): 500 discs
Physical Size
Height 9.7 in (24.6 cm)
Width 9.5 in (24.1 cm)
Width
with left side cover open 23.8 in (60.5 cm)
Depth 14.8 in (37.6 cm)
Depth
with printer tray extended 22.25 in (56.5 cm)
Weight 45 lb (20.4 kg)
Weight
with packaging 50 lb (22.7 kg)
Interface USB 2 (Universal Serial Bus) – B type connector
Rimage Everest 600 and Everest III Printer Specications
Note: The most up-to-date technical specications for the Everest printer are located at www.rimage.com/support. From
the Support menu, select > Printer Series > Product Name > User Manuals tab > Specications link.
Specications are continued are page 7.

72000621_B
Important Information
Everest 600 Everest III
Minimum PC
Requirements -Important! If you do not understand these requirements, ask your computer
technician for help or refer to your PC documentation.
Windows-based PC Processor and Available Space Needed: Celeron 2.0 GHz or better with 512 MB
RAM
Port: USB port
Supported operating systems:
• Windows Vista Business with SP1 (CD Designer Software Suite versions 8.1
and higher; standalone printer and AutoEverest only)
• Windows Vista Business, Enterprise, and Ultimate with SP1 (Rimage Software
versions 8.2 and higher only, when used with an autoloader; CD Designer Software
Suite versions 8.2 and higher only, when used with a standalone printer or
AutoEverest)
• Windows XP Professional SP3
• Windows XP Professional SP2 (Rimage Software versions 8.1 and lower only)
• Windows 2000 Professional SP4 (Rimage Software versions 8.1 and lower only)
• Windows Server 2003
Macintosh Computer Processor and Available Space Needed: G3 or better with 512 MB RAM
Port: USB port
Supported operating system: Macintosh OS X version 10.4/10.5
Power 100 – 120V 500W or 220 – 240V 500W 50 / 60 Hz (manual switching)
Temperature
and Humidity Operating
Conditions
Printer Storage
Requirements*
Ribbon Storage
Requirements**
59° to 86° F
(15° to 30° C)
-13° to 104° F
(-25° C to 40° C)
41° to 95° F
(5° to 35° C)
30% to 80%, non-
condensing Up to 90% 45% to 85%
Temperature
Humidity
*Printer storage requirement values are for the printer without a print ribbon or retransfer ribbon.
**For optimum results, make sure that Everest ribbons are stored within these ranges.

92000621_B
Printer Requirements
Printer Requirements
This section describes ribbon, label design, and print requirements for the Everest printer.
Ribbon Requirements
-Important!
• Rimage only supports the use of Rimage brand ribbons in our printers. Printer issues that occur as a result of using
ribbons from manufacturers other than Rimage are not included under your Rimage warranty or maintenance
agreement.
• For optimum results, make sure that Everest ribbons are stored at a temperature between 41° and 95°F (5° to 35°C)
and humidity level between 45% and 85%.
• Avoid moisture and direct sunlight.
• Do not reuse ribbons.
• Use only ribbons designed for your model of Everest printer. Refer to the tables below.
The Everest printer requires a print ribbon and a retransfer ribbon. The standard print ribbon has three colors: Cyan, Magenta,
and Yellow (CMY). These three colors combine in printing to create full-color discs. Print ribbons are also available in black
and CMY+White. CMY+W is available for Everest III only.
Everest 600 Ribbons
Ribbon Type Everest 600 Part
Number
Number of Discs
Printed
3-Color (CMY) 2000487 500
Black (monochrome) 2000490 1000
Retransfer ribbon (1000 prints) 2000491 1000
Everest III Ribbons
Ribbon Type Everest III Part
Number
Number of Discs
Printed
3-Color (CMY) 203638-001 500
4-Color (CMY+W) 203639-001 375
Black (monochrome) 203640-001 1000
Retransfer ribbon (500 prints) 203474-001 500
Retransfer ribbon (1000 prints) 203384-001 1000

10 2000621_B
Rimage Everest™ III and 600 User Guide
Label Design Requirements
The Everest printer Windows-compatible software ships with the CD Designer™ label editor software. This software is
installed on your PC during a typical installation of the Rimage software. If you have a Windows-based PC, you can use CD
Designer to design your labels.
Note: CD Designer is not Macintosh-compatible and will not be installed with the Macintosh-compatible Rimage software.
If you are using a Macintosh, or prefer to design labels in a software application other than CD Designer, use the following
criteria.
• Label design size – Design labels with a height of 12 cm and width of 12 cm. A full-size disc is 120 mm (4.723”) in
diameter. The hole is 15 mm (0.59”). The printable area and hub sizes vary depending on the disc manufacturer.
Note: The media that are in Rimage Media Kits have a printable area of 118-24 mm. On most labels, print settings of
118 mm and 24 mm are recommended.
• File format – For best results, save your labels as JPEG or TIFF les. However, if you are using the Everest printer on
a Rimage autoloader, these le formats must be imported into CD Designer and saved as CD Designer les (.btw) or
converted to PDF les before printing.
• Color mode – If your Everest printer is on a Rimage autoloader, convert all labels to the RGB color mode in order to
import them into CD Designer. If the Everest is a standalone printer or on an AutoEverest AutoPrinter, and you are printing
directly from an image-editing program, you can work in the color mode of your choice.
• Resolution (pixels per inch) – For best results, use images set to a minimum of 300 pixels per inch. For the Everest 600,
you may notice better results if you use images with 600 pixels per inch or higher.
Print Requirements
Any label you create and save through CD Designer is in the correct le format (.btw) for printing to an Everest on a Rimage
autoloader. You can also print labels saved as PDF les if your Everest is on a Rimage autoloader.
If you are using a standalone Everest printer or an AutoEverest AutoPrinter, you can print directly from any application with
print capability.
Printable
Area 118 mm
Hub Size
24 mm

112000621_B
Identify the Parts of the Everest Printer
Identify the Parts of the Everest Printer
This section describes the Everest printer hardware and features.
Front View
Side
Cover
Side Cover Latches
Handle
Control
Panel
Printer Tray

12 2000621_B
Rimage Everest™ III and 600 User Guide
Control Panel
The control panel is located on the front of the printer. It includes an operator button and four indicator lights.
(One light is on the operator button.) The control panel allows you to monitor and control the Everest printer.
The table below identies the name and function of all parts of the control panel.
Control Panel Indicators
Image Name Function
Operator button The Operator button is used to complete the following tasks:
• Open the printer tray
• Close the printer tray
• Reset after an error
• Put the printer into sleep mode
Tip: To put the printer into sleep mode, press and hold the
Operator button for 10 seconds. To resume normal operation,
press the Operator button again.
Error indicator light (on
the operator button)
The Error indicator light illuminates when operator action is required.
Disc Present indicator
light
The Disc Present indicator light illuminates when a disc is placed on
the tray or when the disc is properly clamped.
The Disc Present indicator light ashes when there is a problem. The
number of ashes in each cycle indicates the type of problem.
1 ash = Side cover is open or ribbon latch 1, 2 or 3 is open
2 ashes = Print ribbon problem (incorrect, missing, or depleted
print ribbon)
3 ashes = Retransfer ribbon problem (missing or depleted
retransfer ribbon)
4 ashes = Error upon clamping the disc on the printer tray
Active indicator light The Active indicator light illuminates when the printer has completed
initialization.
The Active indicator light ashes when the Everest printer is receiving
data from the host.
Power indicator light The Power indicator light illuminates when the Everest printer is
powered on.

132000621_B
Identify the Parts of the Everest Printer
Back View
Printer Cable
Connector
USB Connector
Mode Switch
AC Voltage
Switch
Storage Position for
Shipping Screw
Original Position of
Shipping Screw
Power
Connector

14 2000621_B
Rimage Everest™ III and 600 User Guide
Switches
There are two switches on the rear of the
Everest printer: the mode switch and the
AC voltage switch.
Mode Switch
-Important! After changing the mode, the printer must be powered off and back on again for the change to be recognized.
The mode switch is a rotary switch used to set the operational mode of the Everest printer. The opening at the base of the cap
on the switch indicates the selected mode. When the printer is shipped, it is set to the correct mode for your operation. You
should not have to change the switch position unless you perform diagnostic tests.
Switch Position Use
0 Standalone printer
2Rimage autoloader or
AutoPrinter
3 Diagnostic testing
All others Not used
AC Voltage Switch
The AC voltage switch is used to select the AC voltage of the power outlet. This switch has two positions: 110V and 220V.
 Warning! Set the AC voltage switch to match the voltage of the AC power outlet.
AC Voltage
Switch
Mode Switch

152000621_B
Operate the Everest Printer
Operate the Everest Printer
This section provides the information needed to operate your Everest printer.
Power On and Off the Everest Printer
The Everest printer does not have a power switch. The printer is powered on and off according to your system setup. Refer to
the sections below.
Power On or Off a Standalone Printer
Follow these steps if your Everest is a standalone printer.
• To power on the printer, connect the power cord from the Everest printer to a power outlet.
• To power off the printer, disconnect the power cord from the rear of the Everest printer.
Power On or Off a Printer Connected to an Autoloader or AutoPrinter
Follow these steps if your Everest is connected to an autoloader or AutoPrinter:
• To power on the printer, power on the autoloader or AutoPrinter.
• To power off the printer, power off the autoloader or AutoPrinter.
Note: The printer enters sleep mode if it is idle for more than 30 minutes. When this occurs, the printer will take 2-3
minutes to warm up after a job is sent to the printer.
Place a Disc on the Printer Tray
Use this procedure to place a disc on the printer tray.
1. Press the operator button. The printer tray opens.
2. Place the disc on the print pad with the printable surface facing up and the stacking ring facing the print pad.
-Important! To
avoid scratching
or damaging the
recording surface
of the disc, the disc
must not rest on the
holding pins or the
centering pin.
Holding Pins
Print Pad
Printer Tray
Centering Pin

172000621_B
Set Your Printing Preferences
Set Your Printing Preferences
This section provides the information needed to set up your printing preferences and check the amount of print and retransfer
ribbon remaining using a Windows PC or a Macintosh.
Set Your Printing Preferences on a Windows PC
Printing preferences allow you to set up your Everest printer to produce the best possible labels on your discs.
Note: Unless otherwise indicated, all Windows navigation statements are Windows XP paths. Windows Vista, Windows
2000, and Windows Server 2003 navigation may differ slightly.
Access Printing Preferences (PC)
Use one of the procedures below to access the Everest Printing Preferences.
Access Printing Preferences through the Windows Start Menu
Note: Using this method, printing preferences are saved in the printer driver settings and are applied to all newly created
labels.
1. Select: Start > Printers and Faxes.
2. Right-click the appropriate Everest printer. The dropdown menu displays.
3. From the dropdown menu, select Printing Preferences. The Rimage Everest Printing Preferences dialog box opens.
Access Printer Preferences through CD Designer
Note: Using this method, printing preferences are saved with the label le and are used instead of the printer driver
settings.
1. Open the desired label le in CD Designer.
2. From the File menu, select Print.The Print window opens.
3. From the Name dropdown list, select the appropriate Everest printer.
4. Select the Document Properties button. The Rimage Everest Properties dialog box opens.
Access Printer Preferences when Printing PDFs
Use the procedure below to access printing preferences for PDF les.
-Important! The procedure below applies only if you are printing PDF labels using a Rimage autoloader. It does not apply
if you are using an AutoEverest AutoPrinter. With this procedure, the changes to the settings are global and apply to all
PDF labels.
1. Select: Start > Printers and Faxes.
2. Right-click on the appropriate Everest printer. The dropdown menu displays.
3. From the dropdown menu, select Properties. The Rimage Everest Properties dialog box opens.
4. From the Rimage Everest Properties dialog box, select the Advanced tab.
5. At the bottom of the Advanced tab, select Printing Defaults… The Rimage Everest Printing Defaults dialog box opens.

18 2000621_B
Rimage Everest™ III and 600 User Guide
Set the Media Type, Media Size, Orientation and Ribbon Type (PC)
1. Access printing preferences. Refer to page 17 for instructions.
2. Select the Main tab.
3. View or change the printing preferences.
a. Select the appropriate Media Type.
b. Select the appropriate Media Size.
c. Select the desired number of Copies.
d. Select the desired Orientation.
e. Select the appropriate type of Ribbon.
If you select CMY+White for the ribbon type, select Manual or Auto.
• Select the Manual radio button to manually determine where you would like the a white background to be
applied.
If you select Manual, select Step 1 (CMY) or Step 2 (White).
Note: The Manual options are intended to be used as part of a two-print sequence on the same disc. For the
rst print, select Step 1, and for the second print select Step 2.
• Select the Auto radio button if you want a white background to print automatically.
If you select Auto, select Complete white undercoat or Make pure white transparent from the dropdown list:
Select Complete white undercoat to apply a white background to the entire printable area of the disc. The
printable area is dened on the Advanced tab.
Select Make pure white transparent to print only the areas of the label that are not pure white. Pure white
label areas print as transparent areas on the disc surface.
4. When you have made the desired choices in the Rimage Everest Printing Preferences window, select Apply.
5. Select OK to close the Rimage Everest Printing Preferences window.
Set the Print Quality, Color Matching and Image Adjustments (PC)
1. Access printing preferences. Refer to page 17 for instructions.
2. Select the Advanced tab.
3. View or change the printing preferences.
a. Select the desired Print Quality.
• For the Everest 600, select Photo or Graphics.
• For the Everest III, select Normal or Best.
b. Select the desired criteria for Color Matching.
Note: The default setting for color matching is Match for CMYK printing.
c. From the Image dropdown list, select None, High contrast, Vivid colors, or Custom.
If you select Custom,the Settings button becomes active:
i. Select the Settings button. The Custom Settings window opens.
ii. Select the desired Print Threshold Settings.
iii. Move the Contrast Boost slider to adjust the image contrast.
iv. Move the Saturation Boost slider to adjust the image saturation.
v. Select OK to close the Custom Settings window.
4. When you have made the desired choices in the Rimage Everest Printing Preferences window, select Apply.
5. Select OK to close the Rimage Everest Printing Preferences window.

192000621_B
Set Your Printing Preferences
Set the Printable Area (PC)
This functionality allows you to adjust the printable area settings for standard CD/DVD 120 mm media, which sets the outer
and inner diameters to print the disc label without overlapping the disc edges.
Note: Printable area settings created within a CD Designer label le will override the printer and fax settings on Windows.
1. Access printing preferences. Refer to page 17 for instructions.
2. Select the Advanced tab.
3. View or change the Printable Area preferences.
a. Select the Modify button. The Printable Area Settings window opens.
b. To modify only Standard Area settings, select the Standard radio button.
i. Enter the desired Outer Diameter.
ii. Enter the desired Inner Diameter.
c. To print on a disc with a stacking ring, select the Advanced radio button. The Hub Area settings display.
i. Enter the desired Outer Diameter for the hub.
ii. Enter the desired Inner Diameter for the hub.
d. Select OK to save the changes. The Printable Area Settings window closes.
4. When you have made the desired choices in the Rimage Everest Printing Preferences window, select Apply.
5. Select OK to close the Rimage Everest Printing Preferences window.
Tip: Most discs like the one shown above
have the following printable areas:
• Outer Diameter 118 mm
• Inner Diameter 24 mm
Tip: Most discs like the one shown above
have the following printable areas:
Standard Area:
• Outer Diameter 118 mm
• Inner Diameter 38 mm
Hub Area:
• Outer Diameter 35 mm
• Inner Diameter 17 mm