Rinnai ZERO CLEARANCE User manual

RIB2310/RIB2311 Sapphire/Neo Zero Clearance Box Assembly
11955-F 06-14
1
Rinnai New Zealand Ltd. 0800 746 624
Rinnai Australia Pty. Ltd. 1300 555 545
Before installation:
• Unpacktheassemblyandcheckfordamage—DONOTinstallanydamageditems
• Checkallcomponentshavebeensupplied
• Readtheseinstructionstogetanoverviewofthestepsrequiredbeforestartingtheinstallation
Failuretofollowtheseinstructionscouldcauseamalfunctionoftheappliance.Thiscouldresultin
seriousinjuryandpropertydamage.
3
5
4
2
10
1
10
9
12
8
5
6
2
7
R2340
Item Qty. Description
1 1 ZCboxbase
2 2 ZCboxside
3 1 ZCboxtop
4 1 ZCboxrear
5 1 ZCspigotguide
6 2 Panelburnboxguideside
7 1 Airductoutletgasket
8 1 Spigottopassembly
9 1 Spigotrear
10 2 Edgeprotectorwhite
11 31 Screw8x10ABzinc
12 2 Rivetpopplain73AS4.2
Important
Toensurethespigotassemblylinesupcorrectlyinsidetheenclosureandthattheapplianceis
installedush,thefrontedgeofthezeroclearanceboxshouldsitushwiththefrontedgeofthe
claddingsurface.
Thedrywalldropsdowntothelevelindicatedbythetwoarrowseithersideofthebox.
Toputtogetherthefullassemblyyoualsoneedtohavetheuespigot(orderedseparately).
RIB2310/RIB2311 Sapphire/Neo
Zero Clearance Box assembly

RIB2310/RIB2311 Sapphire/Neo Zero Clearance Box Assembly
11955-F 06-14
2
Rinnai New Zealand Ltd. 0800 746 624
Rinnai Australia Pty. Ltd. 1300 555 545
General information
Ø 146
81
790
361
Ø 53
86
45
650
Assembly
1. Rivet the spigot guide to the spigot assembly
Assembleuespigot,andrivetfromtheunderside,thespigotguidehandleprovidedinthezero
clearanceboxkittothespigotassembly.
When this spigot is used with the zero clearance box
these dimples are to be drilled at Ø3.2

RIB2310/RIB2311 Sapphire/Neo Zero Clearance Box Assembly
11955-F 06-14
3
Rinnai New Zealand Ltd. 0800 746 624
Rinnai Australia Pty. Ltd. 1300 555 545
Assembly
2. Assemble base, sides and rear panel of zero clearance box
Liethebasepanelontheoorandusingthescrewsprovidedintheassemblypack,screwtheside
panelstothebaseandthenattachtherearpanel.
3. Attach full spigot assembly and top panel
Drilloutthetwo3.3mmholesinthespigotwherethetwodimplesarelocated.Screwthefullspigot
assemblytothebackpanelofthezeroclearancebox(thoughthebackofbox)andattachthetoppanel.

RIB2310/RIB2311 Sapphire/Neo Zero Clearance Box Assembly
11955-F 06-14
4
Rinnai New Zealand Ltd. 0800 746 624
Rinnai Australia Pty. Ltd. 1300 555 545
Assembly
4. Slide into the enclosure and secure
Slidetheassembledzeroclearanceboxintotheenclosureandxthetopandsidestotheenclosure.
Therearetwosetsofscrewholes,thesetyouusewillbedependentonthecladdingthickness.Thezero
clearanceboxMUSTBEinstalledushwiththecladdingsurfacetoensurealignmentoftheue.
Cladding surface
Zero clearance box
front cutout
Top of Neo engine
Top of zero clearance box
5. Apply edge protector
Applywhiteedgeprotectorsprovidedintheassemblypacktothegasandelectricalaccessholes.
6. Side rails
Siderails(number8onfrontpage)needtobeattachedtothetopoftheNeoengineasshown.
N
Side rails Spigot guide handle