Rinnai RH-90 CGT User manual

SHANGHAI RINNAI CO, .LTD
RH-90 CGT
CORPORATION
CONTINENTAL COOKER HOOD
Thank you very much for choosing
Rinnai cooker hood. Before operating
the cooker hood, please read this
instruction manual carefully and keep
this instruction manual in a safe place
for future use.
CONTENTS : PAGE
PARTS NAME.......................................... 1
INSTALLATION...................................... 2~3
HOW TO USE.......................................... 4
ATTENTION............................................. 4
TROUBLE SHOOTING............................ 5
MAINTENANCE....................................... 6
RH-90 CGT
TOLL FREE: 0800-1-889-889
http://www.rinnai.co.id
RIT-0003-125-10

PARTS NAME MAINTENANCE
!
!
Pull out the plug to cut electrical power
During cleaning and maintaining, please wear glove, the edge of the accessories
may hurt your hands.
Cleaning
1. The oil net and oil cup should be cleaned once a week with special detergent for
filter or detergent mixed with a little alkali.
2. Clean the impeller and rotating parts with soft detergent, clean the cover of the
cooker hood if necessary.
3. The cover of the main body should be cleaned with soft detergent and soft cloth to
prevent scratch.
4. Please DO NOT wet electrical parts.
Replace the light bulb
Remove the lamp cover with pull out the holder, replace the light bulb with new
one, and then fix the lamp cover
- 6 -
- 1 -
Oil Net
Key
Oil Cup
SalverL o w e r
Glass
Cover
RH-90 CGT
Model Voltage Motor Input
Power Lamp N.W Total Power
RH-90CGT
Size
900x525x585 Single Motor
Motor
Type
AC220V 50Hz 218 W
Outlet
Diameter
180mm
9W
Airflow
12.5 3
±0m /min
24.5kg
Noise
69dB
227W
Air
Pressure
180Pa
TECHNICAL DATA

INSTALLATION
1. NOTICE BEFORE INSTALLATION
2. INSTALLATION DIRECTION
- 2 -
- 5 -
!
!
!
!
!
!
The reference height from the table cooker to the cooker hood is 650 - 700 mm.
Above the cooker make three holes on the wall with diameter of 10mm and
distance between adjacent hole is 165 mm (see installation sketch). Push the fisher
into the holes on the wall until on same surface with the wall.
Hang the cooker hood on the hook steadily.
Connect the outlet pipe with the outlet cover with three pieces of ST 2.9 x 8 screws.
Put the rubber packing on the outlet of cooker hood, and fix the outlet cover on the
outlet of cooker hood 3 pieces of M5 x 12 screw.
Extend the outlet pipe out of the room with reasonable length (the extended length
should be less than 2 meters).
Malfunction
A f t e r p r e s s t h e
function button, the
cooker hood and the lights do not work
Lights work and the motor doesn’t work Cooker hood shaking.
Only one button
works
Absorbing inefficiently
Possible Cause Remedy
Plug do not fit properly
The lamps are damaged
The wire and/or the cable disconnected
The transformer for lights is damaged
Change the lamp
Contact our distributor/After Sales Service
Contact our distributor/After Sales Service
Check the plug and insert completely
Contact our distributor/After Sales Service
Contact our distributor/After Sales Service
Check and remove the obstacle
Hang the cooker hood steady
Tighten it
Contact our distributor/After Sales Service
Contact our distributor/After Sales Service
Contact our distributor/After Sales Service
Check it and make it flexible
Close the window reasonably
Clean it Contact our distributor/After Sales Service
Lower the cooker hood
The impeller are stopped
The capacitor is disconnected and/or
damaged
The motor is damaged
The motor is not fixed tight The damaged impeller break the balance
Hanging is not steady
Connection with the control board not well
The switch is out of order
The flakes on the outlet cover not open
completely
Air flow is too strong around the cooker
hood
The oil filter net board is too dirty
The wire and/or cable damaged
Cooker hood is too high
TROUBLE SHOOTING
!
!
!
!
!
!
!
!
!
!
!
!
!
When install cooker hood, be careful that the cooker hood does not come in
contact with any metal parts (the lath in the wall or the like) of the house.
Do not install or mount the body of the cooker hood inside the wall because
leakage current, if any, on the steel mesh inside the wall will come in contact with
the casing.
Use gas cooker within the width of cooker hood
Do not use cooker hood by modifying switch, etc.
Exhaust air discharges from air discharge outlet shall not effect the flame of gas
cooker.
Check strength of wall, please install cooker hood to wall which can hold weight of
product. (15.0 kg)
Wooden wall
When the thickness of wall is more than 20 mm, install to wall directly.
When the thickness of wall is less than 20 mm, fix reinforcement first, then
install cooker hood to reinforcement.
Concrete, Tail Wall.
Fix reinforcement to wall or use screw fisher.
Brick Wall
Fix reinforcement to pillar first.

4. PACKING LIST
INSTALLATION HOW TO USE
ATTENTION
Insert the electrical plug into the socket steadily and safely
1. Clock adjustment
Push ¿key, clock display will turn on and the hour on the clock will start to blink,
push or ¿to find desired hour, push again ¿the minute on the clock will blink
find desired minute by pushing or ¿, push again ¿to exit from adjusting mode.
2. Motor
Push the motor will run at high speed, push for second time the motor will run
at middle speed push for third time the motor will run at low speed. Push again
the motor will stop.
3. Lamp
Push the lamp will turn on, and push again the lamp will turn off.
!Must use two legs plug with single phase and safely earthen.
!DO NOT discharge the exhaust from the cooker hood into the hot pipe.
!DO NOT dismantle and clean the cooker hood without disconnecting the power.
!Clean the dirt and oil on the cover regularly often. DO NOT wet the motor, control
board and other electrical parts.
!DO NOT dismantle and maintain the cooker hood unless by qualified person.
!Must use the special wire or cable, from our distributor/after sales service when
your cooker hood wire or cable is damaged.
!DO NOT touch the lamp with hand when they are working. The hot lamp may
burn your hands.
!Clean the cover surface with soft cloth and wipe gently to prevent scraping the
scraping the coating surface.
!Keep the kitchen well ventilated when the cooker hood used with gas cooker(s)
during cooking.
!DO NOT clean the cooker hood without reading the instruction manual.
!DO NOT change the specification of the electric parts during maintenance.
!The working cooker hood may blow out the flame of the cooker (s).
!This cooker hood is house electrical appliance. Do not use it in other special
circumstance.
!Put the oil cup into oil net before using.
- 4 -
- 3 -
NO
1
2
3
4
5
6
7
8
9
10
11
12
13
14
NAME
Main body
Pothook
Special discretness
Oil cup
Outlet pipe Ø 180 x 2000mm
Ø 10 plastic fischer
Rubber packing
M 5x14 screw
ST 2.9x8
Instruction manual
Quality certificate
Warranty card
Screw fisher
Outlet cover
QUANTITY
1 pcs
1 pcs
1 pcs
1 pcs
1 pcs
3 pcs
1 pcs
3 pcs
3 pcs
1 pcs
1 pcs
1 pcs
3 pcs
1 pcs
4‑ 10
165 165
905
650‑700 505
3. INSTALLATION SKETCH