Rinnai RH-9025A User manual

Warning……………………………………………….
Parts Name……………………………………………
Installation…………………………………………….
Installation Instruction……………………………….
Caution………………………………………………...
Operation Instruction…………………………………
Maintenance & Cleaning……………………………..
Trouble Shooting………………………………………
Warranty & Wiring Diagram……………………….
COOKER HOOD
INSTRUCTION MANUAL
NAME
PAGE
Products and accessory …………1
Dimensions…………………….....2
Caution………………………..…..4
Operating Instruction…………….5
Maintenance ＆
＆＆
＆Cleaning…........6
Trouble Shooting……………….…7
Wiring Diagram……………….….8
Specification……………………....9
Model:RH-9025A
Instruction………………………..3

PART NAME
RH-9025A
Accessories
Aluminium Tube (up) (1 PCS)
Aluminium Tube (down) (1 PCS)
Aluminium Cover Fixing Assy (1 PCS)
Connector (1 PCS)
Charcoal Filter Assy (1 PCS)
Aluminium pipe (1 PCS)
For Fixing Assy screw (2 PCS)
For Aluminium Tube screw (3 PCS)
1
Electric Box Cover
Power Cable
Tube Top Cover
Fan Blade (Left)
Ventilator Seal
Body
Capacitor
Control Board
Fan Blade (Right)
Motor
Ventilator Body
Oil Plate
Main Tube Unit
LED Light
Electric Box
Oil Cup Base
Mesh Filter
Oil Cup
Control Panel Kit
Light Panel

Dimensions
2
MODEL
A B C
RH-9025A 210mm 896mm 500mm
300mm
298mm
896mm
40mm
500mm
min 470 max 910 mm
(*Excluding with height of main unit)
Hook Location A
210
C
40
500
343 153(6")
373
343
B
896
500
290
285
393
20

Installation
Main Set Installation:
The minimum distance between the cooker and the appliance is 75-90CM, and
drill holes on the wall. Screw the main set by using screw nut together. Adjust
the main set till horizontal line.
1. Aluminium Tube Installation:
Aluminium Tube Set Installation Diagram
3
300mm
298mm
896mm
40mm
500mm
min 470 max 910 mm
(*Excluding with height of main unit)
Keep it horizontal (level)
75~90cm
Install alum inium tube bracket
according to the kitchen cabinet
design. Find the suitable location
and install it on the w all.(Fig 1)
A djust aluminium tube height
according to the kitchen cabinet
design.Insert the alum inium tube
into the indentation.(Fig 2 )
Screw the upper alum inium tube and
the bracket(Fig 3)
A luminium tube bracket install
A lum inium tube install(1)
A lum inium tube install(2)
Fig 1
Fig 2
Fig 3

Caution
Surrounding Environment:
The cooker hood should install near outdoor window.
Let the exhaust air from the tube blow out easily thru
the window. Alternatively, make a hole on the wall,
and let the exhaust air from the aluminium tube blow out.
Do not squash the aluminium tube into the hole. However,
do not select a place, where has too many windows. That is
because excess ventilation might affect the result of the (fig1)
cooker hood.(fig1)
Warning: Unplug the power socket before uninstall.
1.Please keep a minimum 75 –90 cm distance between
cooker hood and cooker. Different types of cooker
might require a bigger space.(fig2)
(fig2)
2.Do not flame under the cooker hood. (fig3)
(fig3)
3.Adjust the aluminium tube to make sure all the exhaust air has blown out successful.
4.There shall be adequate ventilation of the room when the cooker hood is used at the
same time as appliances burning gas or other fuels.
5.Accessible parts may become hot when used with cooking appliances.
6.The air must not be discharged into a flue that is used for exhausting fumes from
appliances burning gas or other fuels.
7.The screw must tighten up after fixing the cooker hood.
4
min
650mm
75-90cm

Operating Instruction
Light Timing Speed(-) Monitor Speed(+) Turbo Power
Instruction：
：：
：
Power：
：：
：
Press this button to turn on the range hood and blue indicate light up, press again to turn
off all the functions and blue indicate light off.
PS: If power on without any action for 9 minutes, the system will off
automatically.
Turbo：
：：
：Press this button once to turn the motor operating to the maximum
speed and blue indicate light up, press again to turn off, this button also allows
you to turn on the power.
Speed Adjusting：
：：
：
1.Press (+) for medium speed start。
2.Press (-) for low speed start。
3.Press (+) or (-) after power on to adjust the speed。
4.(+) Button and (-) Button are also allow to turn on the power。
This range hood is programmed to provide 3 operating speed, which are High /
Medium / Low Speed。
Monitor(Green)：
：：
：
Monitor will indicate motor speed (1、2、3) according to motor speed.。When the
timing function on, the monitor will indicate the rest of time, the monitor starts
blink for the last minute.
Timing：
：：
：
Press timing button during operating for delay off and blue indicate
light up. First press for 3 minutes, followed by 15、30、45、60、90
minutes then back to 3 minutes as a circle.
Delay function will maintain the default speed that set up by the
user.
Press (+)、(-) button during timing function to adjust delay off
time.
Press this button under power off condition, the range hood will on
with low speed and 3 minutes delay off.
Light：
：：
：
This button allows you to turn on / off the light. And also allow to
turn power on only.
5
總
T urb o
調
顯
調
定
照

Maintenance ＆
＆＆
＆Cleaning….
1. There is a fire risk if cleaning is not carried out in accordance with the
instructions.
2. Be careful of the flame when cooking alcoholic food. It might cause to burn
the cooker hood.
3. Make sure the ventilation is good when using glass hob and cooker hood
together.
4. Wipe the cooker hood with a soft damp cloth.
5. Do not spray water directly on the cooker hood to avoid electric shock or
damage to it.
6. Use mild detergent to clean the impeller. Pull out the oil cup, and wash it.
7. Always wash or change the filter, and clean up the cooker hood regularly.
8. Minimum clean up the cooker hood once a week.
9. Kindly follow this cleaning instruction to avoid dangerous.
10. If the supply cord is damaged, it must be replaced by the manufacturer, its
service agent or similarly qualified persons in order to avoid a hazard.
11. While having grease to filter, please pull down and wash.
6

Trouble Shooting
1. Motor Malfunction:
•Check the electrical wiring.
•Check the power plug, On / Off switch, or fuse.
•Check the impeller. If can move by hand when power is on, means the condenser capacitor
needed to be changed.
•When turn on the motor, it stops immediately, or only 1 motor works, means you need to
change a new motor.
2. Main Set Shaking:
•Check on the welding spots for losing points.
•Have the motor and impeller screwed properly.
•Has the impeller deformed?
3. Weak Suction:
•Far distance between cooker hood and glass hob?
•Check if aluminium pipe is too long or curve. Change to 7-inch diameter if necessary.
•Check if there is excess ventilation.
•Check the aluminium pipe, make sure exhaust air and flame blow out smoothly.
•Window should be closed while operating cooker hood.
4. Oil Plate Broke:
•Please get the original parts from any authorize dealers.
5. Oil Cup Broke:
•Please get the original parts from any authorize dealers.
6. Light Failure:
•Check if wiring is ok.
•Remove the light lampshade, and change a new LED light.
7. While filter have damaging, please pull down and change the new filter.
7

Wiring Diagram
RH-9025A
8
GRAY
BLUE
WHITE
ELECTRIC BOARD
LAMP
LAMP
BLACK
POWER
CONDENSER
MOTOR
YELLOW
WHITE
BLUE
GRAY
WHITE
YELLOW BROWN
WHITE
( BROWN)
WHITE
BLACK
BLACK
BLACK
( BLUE)
FUSE
Control Board
LED Back Light
Optional Equipment

Specification
MODEL
DATA
RH-9025A
MATERIAL SUS304
SIZE W896xD500xH510~950mm
(
((
(＊
＊＊
＊Height: From button of main unit)
Height: From button of main unit)Height: From button of main unit)
Height: From button of main unit)
OUTLET DIA 153mm
FAN SIZE 14CMx2
MOTOR, S 1
INSULATION E
VOLTTAGE/FREQUENCY
240V/50Hz
AMP 1.5A
LIGHT 2W
SPEED Ⅰ
ⅠⅠ
ⅠⅡ
ⅡⅡ
ⅡⅢ
ⅢⅢ
Ⅲ
MOTOR SPEED 1200rpm 1800rpm 2400rpm
CONSUMPTION POWER 180W 220W 270W
AIR FLOW MAX 600m³
³³
³/hr 900m³
³³
³/hr 1200m³
³³
³/hr
C.O.O TAIWAN
9