Rinnai RH-C759-SB User manual

Operation / Installation Manual
操作 / 安装说明
Petunjuk Pemakaian / Pemasangan
Hoạt động / Hướng dẫn lắp đặt
  
Chimney Hood
塔形烟机
Tudung Hisap
Máy Hút Khói Mùi – Dòng Chimney

RH-C759-SB
RH-C759-SG
RH-C759-SC
RH-C759-MB
RH-C759-MG
RH-C759-MC
Rinnai Corporation
English
中文
Bahasa Indonesia
Tiếng Việt
ภาษาไทย

TABLE OF CONTENTS
TABLE OF CONTENTS
English
Page 1 - 7
中文
8 - 14 页
Bahasa Indonesia
Hal. 15-21
Tiếng Việt
Trang 22 - 28

  29 - 35
Version: 2013 10

Safety warnings -------------------------------------------------------------------------------------------------------------------------------------------1
Specifications & components--------------------------------------------------------------------------------------------------------------------------3
Installation -------------------------------------------------------------------------------------------------------------------------------------------------4
Operation---------------------------------------------------------------------------------------------------------------------------------------------------5
Maintenance and care ----------------------------------------------------------------------------------------------------------------------------------6
Troubleshoot ----------------------------------------------------------------------------------------------------------------------------------------------7
Unpacking
•Do not use the appliance if there are obvious signs
of transportation damage.
•
If the power supply cord is damaged, it must be
replaced by the manufacturer, its service agent or
qualified technician to avoid hazard.
•
Please ensure that young children do not play with
plastic bag packaging.
For the installer
•
The extractor hood can be installed over gas and
electric cook top. Minimum installation height from
the bench top to the bottom of the hood is 700mm
(gas range) and 550mm (electric range) (Fig. 1).
For the user
•The extractor hood is designed for domestic use to
eliminate unpleasant odors from the kitchen. Do not
use the hood for uses other than its specific purpose.
•Do not allow young children to play with or operate
the appliance. Supervise its use by the elderly or
infirm.
•Installation and re
pair should be attempted by
qualified technical personnel only.
•
It is dangerous to modify any part of this appliance.
Tampering with electrical connections or mechanical
parts can cause operation faults and may put the
user at risk.
•Never leave high naked flames under the extractor
hood when it is in operation. Always cover lit burners
with cookware.
CONTENTS
Please read this user manual thoroughly before attempting to use this appliance for the first time. This manual contains
important information on safe installation, use and care of the appliance. Keep these instructions for reference and pass
them on to future user.
IMPORTANT
To register your product warranty, please paste the serial numbers stickers enclosed with the packaging on your
warranty card. Please contact your local Rinnai Customer Care Centre should you require further assistance.
SAFETY WARNINGS
English
1

•Always mount the extractor hood over the center of
the hob.
•Ensure that the appliance is installed in a location
with good and permanent ventilation.
•When making the electrical connections, check that
oT
he mains voltage and frequency corresponds
to the technical information shown on the
rating plate.
oE
lectrical connection must be made in
accordance to local standards only. Check that
the voltage in your area is correct before
plugging in.
•Use an electrical connector with earth that is correct
for your location. The electrical connection of this
appliance must be connected to earth (where
applicable):
oGreen & Yellow = EARTH; Blue = NEUTRAL;
Brown =LIVE
•Ducted mode:
oConnect the extractor hood to the exhaust duct
through a pipe of minimum Ø120mm. Use the
shortest and straightest duct route possible.
oDo not connect the extractor hood to exhaust
ducts carrying combustion fumes.
oArrange proper ventilation if the extractor hood
is used in conjunction with other appliances
which are not supplied by electrical power e.g.
gas burning appliances. The kitchen must have a
direct opening to the outside in order to allow
entry of fresh air.
Note: The manufacturer accepts no responsibility for
complaints attributed to the design and layout of the
pipe work.
•Do not flambé or grill with an open flame directly
under the extractor hood. Flames could be drawn up
into the hood by the suction and the grease filters
may catch fire.
•
Monitor cooking continuously as overheated oil
increases the risk of self-ignition.
•Do not operate the extractor hood without a grease
filter.
•It is important to clean and/or replace the filters at
appropriate intervals.
•Grease deposits build-up increases the risk of fire.
•
Always disconnect the unit from the power supply
before carrying out any cleaning or maintenance work
on the hood.
•Ensure that the power supply chord is free from any
heat source or sharp objects.
•Multiple plugs and extension cables must not be used.
Overloading is dangerous and may cause a fire hazard.
Disposal
•This appliance and its packaging are environmentally
friendly and recyclable. Please help us to care for the
environment by disposing the packaging in a proper
manner and recycling any old appliances.
•
Before disposing an old appliance, disconnect it from
the power supply and cut the power supply cord to
prevent hazards.
The manufacturer will not be held liable for any
damages resulting from improper installation nor
failure to adopt proper safety measures during
installation and operational use of the appliance.
Fig. 1
English
2

Model RH-C759
SB/SG/SC/MB/MG/MC
Voltage 220V - 240V / 50Hz
Power of Motor 280W
LED Lights 2 x 2W
Cable Length 1.5m
Appliance
Dimension
(W x D x H):
90cm model
896 x 475 x 565-950mm
Note:
The manufacturer reserves the right to effect any
technological improvement or modification without prior notice.
Ref Qty Product components
A 2 Mounting bracket
B 1 Inner Duct
C 1 Outer Duct
D 1 Blower Assembly
E 1 Charcoal Filter
F 2 Aluminium Filter
Qty Installation components
8 Screw M4 x 8
4 Screw ST5 x 50
4 Ø10 Wall Plug
Qty Documentation
1 Operation / Installation Manual
SPECIFICATIONS
COMPONENTS
Fig. 2
Fig. 3
English
Wall Plug
Wall Plug
3

This appliance can be installed in ducted or recirculation
mode.
Ducted mode (Fig. 4)
•In ducted mode, the extractor hood fan extracts the
cooking vapours and passes t
hem through the
grease filter. The air then flows to the outside.
•The grease filter absorbs the solid particles in the
cooking vapors.
•In this mode, only grease filters are installed
(charcoal filter is optional).
Recirculation mode (Fig. 5)
•
In recirculation mode, the extractor hood fan
extracts the cooking vapors which are purified in the
grease filter and charcoal filter.
•The purified air is then recirculated into the kitchen
via a vent opening in the hood. The grease filter
absorbs the solid particles in the cooking vapors.
•The charcoal filter is designed to absorb cooking
odor. In this mode, both grease filters and charcoal
filters are installed.
Connection to exhaust air pipe (Fig. 6 & 6.1)
•Attach Ø150mm pipe directly to the air outlet and
secure appropriately (Fig. 6).
•If using Ø120mm pipe, connect to the air outlet
using a reducing connector (not provided).
•Secure both joints appropriately (Fig. 6.1).
•Connect pipe to the outdoor duct.
Wall mounting (Fig. 7 & 8)
Do ensure that the appliance is mounted
on a solid
surface which could withstand the appliance’s weight.
•Draw a vertical line at the center of the wall.
•From bench top (see A), draw a horizontal line above
minimum installation height level (see B).
•Mark a reference point at C. Repeat this step on the
other side.
•Drill Ø 8mm holes at center of marking points. Insert
wall plugs in the wall.
•Fix the hood body to wall using 2 (two) ST5 x 50
screws provided. Tighten screws firmly. Note: Adjust
the hood body alignment if necessary (Fig. 9).
•Place mounting bracket on the wall at desired height
level. Align bracket center at vertical line (see D).
•Mark the center of the bracket holes and drill Ø 8mm
holes. Insert wall plugs in the wall.
•Secure mounting bracket firmly using 2 (two) ST5 x
25 screws provided.
•Fix the inner duct to mounting bracket using 2 (two)
M4 x 8 screws provided (Fig. 8).
•Slide the outer duct downwards and ensure that it is
well seated on the hood body.
INSTALLATION
Fig. 4
English
Fig. 5
Fig. 6
Fig. 6.1
Fig. 8
Fig. 7
4

To achieve better air extraction, we recommend you to switch on the blower a few minutes before starting to cook.
Leave it on for approximately 15 minutes after cooking or till all cooking smell is completely removed.
Switch control
Note: Touch the sensor buttons gently to operate this appliance.
On/delay/Off key: Touch to select on/off. When in operating mode, press once to enter into delay mode; default delay
timer is 1 minute. Gently slide through the ten-key slider to adjust the delay time: slide to the right to increase timing, slide
to the left to decrease timing. Maximum delay timing is 10 minutes. When in countdown mode, display will show the time,
and slider indicator will show the speed. Press the on/off key to exit delay timer mode, and to turn off the blower/fan.
Lights on/off: Touch to select lights on/off
Timer setting: When in “off” mode, press and hold the on/off key to enter clock settings. Once the display starts blinking,
press to decrease hour unit and to increase hour unit. After that, press to confirm and proceed to do the same
for the minutes display.
Low speed: Press to turn blower on/off at low speed
Medium speed: Press to turn blower on/off at medium speed
High speed: Press / to turn blower on/off at high speed
Touch slider: Gently slide across to the right to increase blower speed, and across to the left to lower blower speed
Aligning the hood body (if necessary) (Fig. 9)
•Before attaching hood body to wall, adjust the
2(two) screws located on the hood body mounting
points.
•Hook the hood body onto the support screws and
tighten the support screws fully.
•Adjust screws to level the hood body.
Installation must be performed by qualified personnel
only. The manufacturer declines all responsibility for
improper installation and does not accept responsibility
for appliance warranty in the event of damage caused by
incorrect installation.
OPERATION
English
Fig. 9
5

Grease filter (Fig. 10)
•
Grease filters are used to absorb the grease
particles formed during cooking process. The filters
must be removed and cleaned every 4 weeks,
depending on frequency of usage. Clean the filter
either by hand or in the dishwasher. Note: Take
care not to bend the filters during washing.
•
If by hand washing, soak the filters in warm
detergent solution to simplify the removal of
grease. Brush the filters, rinse thoroughly a
nd
leave it to dry before refitting.
•
If by dishwasher, select an appropriate wash
program. Leave it to dry before refitting. Note:
slight discoloration of the filter may occur.
•Removing and inserting the grease filters:
oTo remove, depress the handle and pull down
at the same time.
oTo refit, slot the filter into position. Make sure
that the handle is visible on the outside.
Charcoal filter (where applicable) (Fig. 11)
•
The charcoal filters should be replaced when it is
noticeably dirty or discolored, usually after 6 to 12
months depending on the conditions of use.
•These filters are not washable and
cannot be
restored. To ensure that this appliance functions
effectively, regular maintenance is necessary as
clogged filters restrict airflow and may cause the
motor to overheat.
•Removing and inserting the charcoal filter:
oRemove the saturated charcoal filter from the
blower as shown.
oFit in the new charcoal filter.
Cleaning the appliance body
•Clean the extractor hood using warm detergent
solution and a soft damp cloth. Wipe dry with a lint-
free cloth.
•Avoid using corrosive or abrasive products that could
damage the surface.
Light replacement (Fig. 12 & 12.1)
Replace the light bulb with another which has the
same characteristics as a higher voltage bulb could
damage the electrical unit.
•Removing and replacing the lights:
o
Push out the light assembly from inside of the
hood body (Fig. 12).
oDisconnect the light connector (Fig. 12.1).
oReplace a new set of light assembly. Note: For
purchase of spare part, please check with your
local Rinnai Rinnai Customer Care Centre for
assistance.
oReverse the procedure for refitting.
MAINTENANCE AND CARE
Disconnect the power supply cord before carrying out
any cleaning or maintenance activities. It is important
to clean and/or replace the filters at appropriate
intervals as grease deposits build-up increases the risk
of fire. Do not operate the extractor hood without
grease filter.
You are strongly recommended to follow these safety
instructions. The manufacturer will not be held liable for
any damages to the appliance or any fire hazard due to
failure to observe the above safety recommendations.
English
Fig. 10
Fig. 11
Fig. 12
Fig. 12.1
6

Problem
Possible Cause
Solution
Extractor hood does not
function
No electrical supply
Check that plug is
connected and main power
switch is turned on
Poor airflow
Grease filters clogged with
grease build-up
Clean the grease filters and
refit when dry
Charcoal filters clogged
with grease build-up
Replace charcoal filters
with new sets
Hood suction is not effective
Inadequate ventilation
Ensure that the kitchen is
sufficiently ventilated to
allow entry of fresh air
Charcoal filters are not
installed
Install charcoal filters for
setting in recirculation mode
Motor is running but no airflow
Poor exhaust
Please contact Rinnai
Customer Care Service
Whirring sound
Foreign object may be in
contact with fan blade
Please contact Rinnai
Customer Care Service
Lights are not working
Lamps are burnt out
Replace the damaged lamps
Lamps are loose
Tighten the lamps
TROUBLESHOOT
If problem persists after the above checks, please contact Rinnai Customer Care
Centre for assistance.
Please quote the model number of your appliance as shown on the rating plate
attached to your equipment (Fig. 13).
For service calls under warranty, please note that it is necessary to produce your
proof of purchase and valid warranty card.
Fig.13 - Rating plate is for illustration
purpose only and its specifications
vary across models.
English
7

安全警告 --------------------------------------------------------------------------------------------------------------------------------------------------8
规格和部件-----------------------------------------------------------------------------------------------------------------------------------------------10
安装 --------------------------------------------------------------------------------------------------------------------------------------------------------11
操作---------------------------------------------------------------------------------------------------------------------------------------------------------12
维修与保养-----------------------------------------------------------------------------------------------------------------------------------------------13
常见问题 --------------------------------------------------------------------------------------------------------------------------------------------------14
开箱
•如有明显的运输过程造成的损伤，请不要使用该
器具。
•如果电源线破损，则必须由生产商，服务代理或
者合格的技术人员进行更换，防止伤害风险。
•请确保孩童远离塑料包装。
给安装人员
•此油烟机罩可以安装在燃气炉和电炉上方。从台
面到烟机底部的最小的安装高度为 700mm
(燃气灶) 和550mm (电炉) (图. 1).
给用户
•烟机是适合国内使用的，用于消除厨房的异味。
请不要把烟机使用于其他用途。
•请不要让孩童玩弄或者操作器具。请监督年老体
弱者的使用。
•安装与维修只能让合格的技术人员进行。
•对烟机任意的修改将导致危险。篡改电气连接配
件或机器配件都会导致运行错误并会使使用人员
陷入危险。
•当烟机运行时请不要使用较高火焰的燃烧器。会
点燃燃烧器上面的炊具。
目录
在使用本器具前，请仔细阅读本使用手册。本手册包括重要的涉及人身安全以及器具使用和保养方面的信息。
请保存好这份说明书，以传递给以后的使用者。
重要提示
要注册您的产品保修，需要把序列号贴纸贴到随机器包装的保用证上。请联系当地的林内客户售后服务中心咨
询更新信息。
安全警告
中文
8

•请确保器具的安装地点有良好的通风。
•连接电源时，请按照铭牌所示信息确认电源电压
与频率。.
•电源连接必须符合当地标准。请在插入电源之前
确认当地的电压是否正确。
•请使用符合当地的接地连接器。此器具的电源连
接必须接地 (
合适的 ):
ο绿色 & 黄色 = 接地; 蓝色 = 零线; 褐色 = 相线
•管道模式
：
请使用管径最小为 120mm 的管来连接烟机与排
气管。请尽量使用最短与最直的管道。
ο请不要将火焰排进与烟机连接的排气管。
ο如果烟机与其他非电器器具如燃气器具一起使
用，请务必做好适当的通风。厨房必须打开直
接通往室外的窗门来换气。
注意 :生产商没有任何义务接受管道安装与设计的投
诉。
•
请不要在烟机下方直接燃火或烤火。火焰会被吸进
烟机，里面的油脂过滤器会着火.
•请注意不断观察，因为过热的热油会增加自燃的危
险。
•请不要操作没有油脂过滤器的器具。
•定期清理与更换过滤器很重要，因为油脂积聚会增
大着火的危险。
•请在取出清理或维修之前务必切断电源。
•请确认电源线远离任何热源或尖锐的物体。
•禁止使用多用插头与延长电线。有超负荷的危险，
会引发火灾。
处理
•此器具与其包装都是环保及可循环再用的。
•请帮助我们爱护环境，用适当的方式处置包装以及
旧的器具。
•在处置旧器具前，请切断电源以及移走电源线防止
危险发生。
注意
:
生产商不会对由于任何安装或者通过非正当的
方式安装与运行产生的损坏负责。
图
. 1
中文
9

型号
RH-C759
SB/SG/SC/MB/MG/MC
电压 220V - 240V / 50Hz
马达功率 280W
LED 灯泡 2 x 2W
电缆长度 1.5m
产品尺寸
(W x D x H):
90cm model
896 x 475 x 565-950mm
注意: 生产商拥有改造器具而不预先对消费者进
行告知的权利。
参照
数量
产品配件
A 2 安装支架
B 1 内管
C 1 外管
D 1 风机组件
E 1 木炭过滤器
F 2 铝制过滤器
数量
安装配件
8 螺丝 M4 x 8
4 螺丝 ST5 x 50
4 Ø10 墙钉
数量
文件
1 操作 / 安装说明手册
规格
部件名称
图
. 2
图
. 3
中文
Wall Plug
Wall Plug
10

该器具必须以管道模式或回流模式安装。
管道模式
(图. 4)
•在管道模式中，烟机的风扇会把煮食的油烟吸进管
道并通过油脂过滤器排出屋外。
•油脂过滤器吸收煮食过程中油烟的固体物质。
•在此模式中，
只需安装油脂过滤器
(
木炭过滤器可选性安装
).
回流模式
(图. 5)
•在回流模式里，烟机的风扇将吸走被油脂过滤器
与木炭过滤器净化后的煮食气体。
•净化后的气体之后通过烟机里的一个排气孔回流
进厨房. 油脂过滤器吸收煮食气体的固体物质。
.
•木炭过滤器是设计吸收煮食气味的。 在此模式
里，要安装油脂过滤器与木炭过滤器
。
连接排气管
(图. 6 & 6.1)
•直接把 Ø150mm 管连接到排气口并固定 (图. 6).
•如果使用 Ø120mm 管，用连接器来连接排气口
(不提供).
•固定连接口 (图. 6.1).
•连接管道到外管。
上墙 (
图
. 7 & 8)
确保安装器具的表面稳固，并能支撑器具的重量。
•在墙的中央画一条垂直直线。
•从桌面顶部 (参照 A),在离桌面最低安装水平位置
上画一条水平线 (see B).
•标记一个参照点 C。在另外一边重复此步骤。
•在标记点的中央钻一个 Ø 8mm 的孔，把墙钉钉进
墙内。
•用配套的 2 (two) ST5 x 50 螺丝把机体固定到墙
上。拧紧螺丝。注意: 如果需要可调整机身平衡。
(图. 9).
•在希望的高度处放置安装支架。对准垂直直线校
准支架的中心。 (参照 D).
•标记支架洞的中央，并钻一个 Ø 8mm 的孔。把墙
钉钉进墙内。
•使用配套的 2 (two) ST5 x 25 螺丝固定安装支架。
•使用 2 (two) M4 x 8螺丝固定内管到安装支架
上。 (图. 8).
•滑动外管到下面并确保固定在机体上。
安装
图. 4
中文
图5
图. 6
图. 6.1
图. 8
图
. 7
11

我们推荐在烹煮之前先打开器具几分钟以达到更好的排气效果。在烹煮之后继续开 15 分钟左右，直到气味完全消
失。
开关控制
注意 : 轻轻碰触传感按键来操作器具。
On/delay/Off
按键
: 碰触 on/off 按键。在操作模式中，按一下进入延迟模式; 默认延迟时间为 1分钟。轻轻滑过
十键来调整延迟时间：滑到右边表示增加时间，滑到左边表示减少时间。最大延迟时间为 10 分钟。在倒计时模式
中，显示屏会显示时间，滑碰指示器会显示速度。按下 on/off 键来推出延迟时间模式，然后关闭吹风机/风扇.
Lights on/off: 按触选择灯亮/灭
Timer setting
计时器设置
:
当
“off” 模式中，长按 on/off 按键进入时钟设置。当显示屏闪烁，按 键来减少小时数字
设置，按 来增加小时数字设置。之后，按 键来确认，分钟设置时步骤相同。
Low speed 低速: 按键来开/关低速风机
Medium speed 中速: 按键来开/关中速风机。
High speed 高速: 按/ 键来开/关高速风机。
Touch slider 滑条: 向右轻轻滑动是增加风机速度，向左则是减少风机速度。
校准机体
(
如果需要
)(图. 9)
•在把机体安装到墙上之前，调整 2(two)个在机体
安装点上的螺丝。
•把机体勾到支撑螺丝上并拧紧支撑螺丝。
•调整螺丝来平衡机身。
安装必须由有资质的人士进行。生产商对所有不适当
安装，以及由不当安装引起的损坏负责和器具保修。
操作
中文
图. 9
12

油脂过滤器
(图. 10)
•油脂过滤器是用于吸收煮饭过程中发出的油脂
的。此过滤器必须根据使用频率每 4周清洗或者
移出。过滤器可以用手或洗碗机清洗。注意: 注
意清洗时不要弯曲过滤网。
•如果用手洗，用温水清洗液洗更容易洗掉油脂。
再重新安装回去之前，要擦洗干净并晾干过滤
器。
•如果用洗碗机，选择一个适合的清洗程序。重新
安装回去之前要晾干过滤器。
注意: 过滤器会有轻微的掉色现象。
•移走与插入油脂过滤器:
o要移走，就要拧开中心的螺丝.
o要安装，把油脂过滤器安进去并拧紧螺丝。
木炭过滤器
( 合适处 )
(图. 11)
•木炭过滤器在明显脏污或者褪色时就要更换，通
常在 6-12 个月，根据使用情况而定。
•此类过滤器不能清洗也不能修复。要确保机器功
能正常，定时的保养是必要的，因为堵塞的过滤
器不能排气，并可能导致马达过热。
•从油脂过滤器上移走饱和的木炭过滤器
o从送风机移走已饱和的木炭过滤器，如图所
示。
o装上新的木炭过滤器。
清洗机体
•清洗烟机要使用温水清洗液和软湿布。清洗之后，
用无尘布来擦干。
•避免使用腐蚀性或研磨性的产品，因为这样会容易
刮花产品表面。
灯泡的更换
(图. 12 & 12.1)
更换新的灯泡时，新的灯泡需要与原来的灯泡的
规格一致，高电压会损坏电子元件。
•移走并更换灯泡 ：
o从机体内部按压灯泡组件 (图. 12).
o断开灯泡连接器 (图. 12.1).
o更换新的灯泡组件。 注意: 要购买零件，请与
当地的林内售后客服中心联系。
o倒反刚才的顺序来重新安装灯泡。
维修与保养
请确保主电源在清洗或保养维修之前已经被切断。
定期对过滤器清洗或更换是很重要的，因为油脂积
聚会增加着火的危险。不要在没有油脂过滤器的情
况下开动机器。
注意
:
强烈建议您阅读这些安全提示。制造商对任何由
于不遵守上述安全建议而引致器具损伤或火灾都不需
负任何责任。
中文
图
. 10
图
. 11
图
. 12
图
. 12.1
13

问题
可能导致问题的原因
解决方法
烟机不运作 没电 确认插头已经插上，电源已
经开启。
风量小 油脂过滤器被油脂堵塞
清洗油脂过滤器，晾干后安
装回去
木炭过滤器被油脂堵塞
更换新的木炭过滤器
抽油烟率太低
通风不足 确保厨房通风情况良好以使
新
鲜空气能进入厨房内
木炭过滤器没安装 安装木炭过滤器，以设置为
回流模式
马达启动但是不能抽风 排风不好
请联系林内的售后服务中心
呼呼的声音 风扇页可能有外物碰触到 请联系林内的售后服务中心
灯不亮 灯泡损坏 更换掉烧坏的灯泡
灯泡松了 拧紧灯泡
常见故障的识别与处理
如果进行了以上的确认之后问题依然存在，请联系林内的售后服务中心请求
帮助。
请找出产品的型号，型号在机体的铭牌上，如图所示。(图.13).
如果需要保修服务，请提供购买产品的证明与有效的保修证。
图.13 - 注意
:
铭牌只起插图提示的
作用，不同产品的铭牌不同。
中文
14

Peringatan Keselamatan--------------------------------------------------------------------------------------------------------------------------------15
Spesifikasi dan komponen------------------------------------------------------------------------------------------------------------------------------17
Pemasangan -----------------------------------------------------------------------------------------------------------------------------------------------18
Pengoperasian---------------------------------------------------------------------------------------------------------------------------------------------19
Pemeliharaan dan perawatan--------------------------------------------------------------------------------------------------------------------------20
Pemecahan Masalah-------------------------------------------------------------------------------------------------------------------------------------21
Membuka kemasan
•Jangan gunakan alat ini jika terdapat kerusakan saat
proses pengangkutan.
•
Jika kabel listrik rusak harus diganti oleh pihak
perusahaan. Agen servis resmi atau teknisi yang
berpengalaman untuk menghindari kerusakaan.
•
Pastikan bahwa anak kecil tidak bermain dengan
bekas kemasan plastik ini.
Untuk pemasangan
•Tudung hisap bisa dipasang di atas kompor gas dan
juga kompor listrik. Batas jarak tinggi minimum
pemasangan dari atas kompor ke bagian bawah
tudung hisap untuk kompor gas adalah 700mm dan
550mm untuk kompor listrik (Gbr. 1).
Untuk Pengguna
•Tudung hisap
didesain untuk penggunaan rumah
tangga untuk mengurangi bau tidak sedap dari
dapur. Jangan gunakan tudung hisap untuk tujuan
tidak semestinya.
•
Jangan biarkan anak kecil mengoperasikan tudung
hisap ini. Awasi penggunaan yang dilakukan oleh
orang tua atau orang sakit.
•
Pemasangan dan perbaikan harus dilakukan oleh
teknisi yang berpengalaman.
•
Sangat berbahaya untuk memodifikasi bagian dari
tudung hisap ini. Merusak sambungan listrik atau
bagian mekanik bisa menyebabkan kesalahan
penggunaan dan mungkin menyebab
kan pengguna
dalam bahaya..
•
Jangan pernah biarkan api naik langsung di bawah
tudung hisap. Selalu tutupi dengan peralatan
memasak.
DAFTAR ISI
Silakan baca buku petunjuk ini secara seksama sebelum Anda menggunakan alat ini untuk pertama kalinya. Buku
petunjuk ini berisi informasi penting tentang pemasangan yang aman, cara penggunaan dan perawatan kompor ini.
Simpan buku petunjuk ini sebagai referensi di masa yang akan datang.
PENTING
Silakan salin nomer seri pada stiker yang ada pada kemasan kartu garansi Anda, untuk meregistrasi garansi
produk Anda. Silakan hubungi Layanan Purna Jual RINNAI di kota Anda jika Anda memerlukan bantuan lebih lanjut.
PERINGATAN KESELAMATAN
Bahasa Indonesia
15

•Selalu pasang tudung tepat berada di atas kompor.
•Pastikan bahwa tudung hisap anda terpasang pada
lokasi yang mempunyai ventilasi udara yang
permanen.
•Saat membuat sambungan listrik, periksa :
o
Tegangan utama dan frekuensi sesuai dengan
Informasi teknis yang ada di data plate.
o
Sambungan listrik harus dibuat sesuai dengan
standar local. Periksa apakah tegangan di area
anda sudah benar sebelum dinyalakan.
•Gunakan penghubung listrik ke tanah (ground) yang
sesuai dengan lokasi anda. Sambungan listrik dari
tudung hisap ini harus terhubung ke tanah (yang
dapat dipakai ) :
oHijau & ku
ning= Tanah (GROUND), biru =
NETRAL, Cokelat = FASE
•Mode ventilasi :
o
Hubungkan tudung hisap ke saluran
pembuangan melalui pipa dengan diameter
minimum Ø
120mm. gunakan rute terpendek
dan terlurus yang paling mungkin.
oJangan hubungkan tudung hisap ke saluran
pembuangan yang menghasilkan asap
pembakaran.
o
Atur ventilasi yang tepat jika tudung hisap
dihubungkan dengan alat lain yang tidak
dialirkan sumber listrik misalnya alat
pembakaran gas. Dapur harus mempunyai
ventilasi udara yang terhubung langsung keluar
untuk memungkinkan masuknya udara segar.
Catatan:
RINNAI tidak akan bertanggung jawab
terhadap keluhan yang menyangkut desain dan tata
letak pipa.
•Jangan memasak atau memanggang dengan api
terbuka langsung di bawah tudung hisap. Api bisa naik
samp
ai ke tudung hisap karena terhisap dan
penyaring minyak bisa terkena api.
•
Selalu pantau saat memasak secara terus menerus
karena minyak yang terlalu panas bisa meningkatkan
resiko kebakaran.
•Jangan mengoperasikan tudung hisap tanpa penyaring
(filter) minyak.
•
Sangat penting untuk membersihkan dan atau
mengganti penyaring (filter) pada waktu tertentu.
•Tumpukan endapan minyak bisa meningkatkan resiko
kebakaran.
•Selalu putuskan sambungan tudung hisap ini dengan
aliran listrik saat membersihkan atau melakukan
tindakan pemeliharaan.
•
Pastikan bahwa aliran kabel sambungan bebas dari
berbagai sumber panas atau benda tajam.
•
Steker ganda dan kabel yang terlalu panjang tidak
boleh digunakan. muatan berlebih berbahaya dan bisa
menyebabkan bahaya kebakaran.
Pembuangan
•
Tudung hisap ini dan kemasannya merupakan bahan
yang ramah lingkungan dan bisa didaur ulang. Harap
bantu kami untuk menjaga lingkungan dengan
membuang kemasan pada tempatnya dan mendaur
ulang tudung yang sudah lama.
•Sebelum membuang tudung hisap yang sudah lama,
putuskan sambungan listrik dan potong kabel
sambungan untuk mencegah bahaya kebakaran.
RINNAI tidak bertanggung jawab atas kerusakan akibat
pemasangan yang tidak benar atau kegagalan karena
mengambil tindakan-tindakan keselamatan yang tidak
tepat selama pemasangan dan penggunaan tudung
hisap ini.
Gbr. 1
Bahasa Indonesia
16

Model RH-C759
SB/SG/SC/MB/MG/MC
Tegangan Volt 220V - 240V / 50Hz
Kekuatan Mesin 280W
Lampu LED 2 x 2W
Panjang Kabel 1.5m
Dimensi Alat
(W x D x H):
90cm model
896 x 475 x 565-950mm
Catatan:
RINNAI berhak untuk melakukan pengembangan
teknologi dan memodifikasi tanpa ada pemberitahuan terlebih
dahulu.
Ref Qty Komponen Produk
A 2 Rangka pemasangan
B 1 Saluran kedalam
C 1 Saluran keluar
D 1 Peniup rakitan
E 1 Saringan arang
F 2 Saringan aluminium
Qty Komponen Pemasangan
8 Baut M4 x 8
4 Baut ST5 x 50
4 Ø10 Steker
Qty Dokumentasi
1 Pengoperasian/ petunjuk
manual
SPESIFIKASI
COMPONENTS
Gbr. 2
Gbr. 3
Bahasa Indonesia
Wall Plug
Wall Plug
17

Tudung hisap ini bisa dipasang dengan menggunakan
mode ventilasi dan sirkulasi.
Mode Ventilasi (Gbr. 4)
•
Pada mode ventilasi ini, kipas tudung hisap
membersihkan uap masakan dan melewatinya
melalui penyaring minyak. Udara kemudian mengalir
keluar.
Penyaring minyak menyerap partikel padat dalam uap
masakan.
•Dalam mode ini, hanya filter minyak yang di pasang
(Filter arang adalah opsi).
Mode resirkulasi (Gbr. 5)
•Pada mode sirkulasi, kipas tudung hisap memurnikan
asap masakan, yang dimurnikan di dalam penyaring
minyak dan penyaring arang.
•
Udara yang dimurnikan tersebut kemudian
disirkulasikan lagi ke dalam dapur melalui lubang
udara yang terbuka pada tudung. Penyaring minyak
menyerap partikel padat dalam asap masakan.
•Penyaring arang didesain untuk menyerap bau tidak
sedap. Pada mode ini, baik penyaring minyak dan
penyaring arang harus dipasang.
Koneksi ke pembuangan udara (Gbr. 6 & 6.1)
•Pasang pipa Ø150mm langsung ke
saluran keluar
udara dan pengamanan yang tepat (Gbr. 6).
•Jika menggunakan pipa Ø120mm, hubungkan ke
lubang udara menggunakan pengurangan konektor
(tidak disediakan).
•Amankan kedua sambungan dengan tepat (Gbr 6.1).
•Sambungkan pipa ke saluran keluar.
Pemasangan dinding (Gbr. 7 & 8)
P
astikan bahwa alat dipasang pada permukaan padat
yang bisa menahan berat alat tersebut.
•Gambar garis vertical di tengah dinding.
•Dari dudukan atas (lihat A), gambar garis horizontal
diatas level ketinggian pemasangan minimum (lihat
B)
•Tandai titik referensi di C. Ulangi langkah ini di sisi
lain.
•Lubangi
Ø8mm ditengah poin yang telah ditandai.
Masukkan fischer ke dinding.
•
Perbaiki badan hood ke dinding menggunakan 2
(dua) baut ST5 x 50 yang disediakan. Kencangkan
baut dengan kuat. Catatan : Sesuaikan keselarasan
badan hood jika diperlukan (Gbr. 9).
•Tempatkan pemasangan baut pada dinding di tingkat
ketinggian yang diinginkan. Luruskan penyangga
ditengah pada garis vertikal (lihat D).
•Tandai bagian tengah lubang penyangga dan lubangi
Ø8mm. Masukkan fischer di dinding.
•
Mengamankan pemasangan bracket dengan kuat
menggunakan 2 (dua) ST5 x 25 baut yang tersedia.
•Perbaiki saluran kedalam untuk pemasangan bracket
gunakan 2 (dua) M4 x 8 baut yang tersedia (gbr. 8).
•Geser saluran luar ke bawah dan pastikan itu telah
terpasang dengan baik pada badan hood.
PEMASANGAN
Bahasa Indonesia
Gbr. 8
Gbr. 4
Gbr. 5
Gbr. 6
Gbr. 6.1
Gbr. 7
18