Risco iREX User manual

with the IQ feature
INSTALLATION INSTRUCTIONS
DESCRIPTION
iREX and iREX Plus are PIR detectors specifically designed for request-to-exit (REX) and request-to-enter (REN) applications.
The iREX detectors are designed with the IQ feature (Intelligent Queuing) used to remotely enable or disable the iREX.
The iREX detectors can be installed as stand alone units or in conjunction with Access Control systems.
The iREX can be mounted on both walls and ceilings and are designed with flexible adjustment to cover the specific needs of each secured area.
1. INSTALLATION
IMPORTANT:
The iREX should always be installed with the rounded
side of the detector pointing to your left side when you
are facing the iREX.
iREX Components:
1
2
Adjusting Buzzer Volume:
Masking:
To insert a masking wedge:
To remove a masking wedge:
Masking Coverage:
2. MOUNTING AND DETECTION
Ceiling Mounting 4.6m
Position 0
Wall Mounting 4.6m
Position 0
Ceiling Mounting 2.3m
Position 0
Wall Mounting 2.3m
Position 0
0
CC
4.7m
15.4ft
Wall WallDoor
X
XXXX
Wall
1.2m
3.9ft
1m
2m
0m
(0ft)
(3.3ft)
(6.6ft)
3m
(9.9ft)
4m
(13.2ft)
4.6m
(15ft)
Front View
Top View
Side View
Wall Mounting 2.3m
Position A
Wall Mounting 2.3m
Position B
A
B
2.4m
7.9ft
Wall
Door
1m
2m
2.3m
0m
(0ft)
(3.3ft)
(6.6ft)
(7.5ft)
Side View

3. WIRING 4. DIP SWITCH OPTIONS
1234567
O
N
TTDR-+
NC C NO NC C NO
MIN MAX
PIR
Sensor
LED
Buzzer Volume
Adjustment
DIP Switches
iREX Plus
RELAY 1 RELAY 2
TAMPER
CONTROL LINES
POWER SUPPLY
Terminal Application
"+" "-" Power Connection Connect to power supply between (+) and (-) terminal. (Voltage must be between 12-30 VAC or DC)
"NC,C,NO" Contact Output Wiring
Wiring to an Access Control System
Access Controller
12 - 30 Volt
DC or AC
Power
Supply
+
_
NC C NO NC C NO
TTD R -+
Input
Basic Connection: Magnetic Lock Only
During motion detection, power is removed from
the magnetic lock. The relay behaves according
to the Fail Safe/Fail Secure definition.
Spike Protection
Add a diode or bridge rectifier for locks
that are not spike protected.
Diode /
Bridge Rectifier
Note: It is recommended to set the
Relay Timer Activation to 1/2
second.
"R" Input Terminal Wiring
Parallel Door Control (iREX or iREX
Plus)
Use to control the door both from the
iREX or from an external device (card
reader, keypad) usually placed on the
other side of the door.
(Dip Switch settings
on iREX Plus)
Remote iREX Disable (IQ feature) *
Use the Intelligent Queuing feature to remotely
enable or disable the iREX from a remote device
(such as a floor switch, additional PIR, Keycard,
Burglar alarm system, etc.). The iREX will only
activate by motion if the "R" terminal is open, or
for 10 seconds after it closes. The iREX is
disabled when the "R" input is closed after a
delay of 10 seconds.
Remote Buzzer Control *
Use this wiring option to control the iREX
buzzer from a remote contact. Buzzer is
activated while R is open. Turning the
buzzer on does not affect the relay.
Wiring the Remote Buzzer Control
to an Access Control System*
Access Controller
12 - 30 Volt
DC or AC
Power
Supply
+
_
NC C NO NC C NO
TTDR-+
Input
Output
"D" Input Terminal Wiring * Door Alarm Mode *
If the door is forced open or left open for 10
seconds the buzzer turns on.
Door Secure Mode *
When the iREX is activated but the door remains closed, the relay will drop out after
ten seconds. When the iREX is activated and the door is opened and then closed, the
relay will drop out after 2 seconds.
Maglock
+
_
NC C NO NC C NO
TTD R - +
Door Contacts
(Normally Closed)
Other Inputs
12 - 30 Volt
DC or AC
Power
Supply
+
_
Notes: Relay Timer Mode must be set for at least 16 seconds
The Door Alarm Mode isnot to be considered as a UL listed Burglar Alarm System.
"T" Tamper Switch Wiring * The tamper terminals are connected to the tamper switch, which opens when the cover is opened.
NOTE:
* Available on iREX Plus only
Switch Function Description
1 LED
Operation
ON (default) - LED is activated. The LED turns on when motion is detected.
OFF - LED is disabled.
2 Timer Reset
Mode
ON (default) - Relay timer resets when motion is detected during the Relay operation
time.
OFF - Relay timer does not reset when motion is detected during the Relay time.
3 Relay Mode
This switch defines the relay's operation when power is removed from the iREX.
OFF (default) - Fail Secure mode. When power is removed from the iREX a locked
door will remain locked and secured against opening. (This mode should be
authorized by your local authority)
ON - Fail Safe mode. When power is removed from the iREX a locked door will
unlock and be safely opened.
(See Contact Output Wiring)
4, 5, 6 Relay Timer
Activation
SwitchRelay Timer
(seconds) 4 5 6
1/2 OFF OFF OFF
1 OFF OFF ON
2 OFF ON OFF
4(default) OFF ON ON
8 ON OFF OFF
16 ON OFF ON
32 ON ON OFF
7 Signal
Processing Determines the detector's PIR detection sensitivity to movement.
ON - High PIR sensitivity
OFF (default) - Low PIR sensitivity.
8, 9, 10 Remote Input
Functions
(See Wiring
options)
Switch
Function 8 9 10
Parallel Door Control (default) OFF OFF OFF
Remote Buzzer Control * OFF OFF ON
Remote iREX Disable * OFF ON OFF
Door Alarm Mode * OFF ON ON
Door Secure Mode * ON ON ON
NOTE:
* Available on iREX Plus only
TECHNICAL SPECIFICATIONS
Power
Voltage 12-30 Volts DC or AC
Current Consumption 8mA standby,
iREX: 30mA max (Relay+LED),
iREX Plus: 50mA max at 12/24 VDC
(including Buzzer)
Relay Output Rating 1A @ 30 volts DC or AC, two form “C”
contacts
Tamper Output Rating 50mA @ 30 volts DC or AC
Buzzer Output (iREX Plus) 85dB with adjustable volume
Output Level at 10ft 69dBA
Detection System
Mounting Height 2.3m - 4.6m (7.5ft – 15ft)
Detection range Width From 0.6m (2ft) up to 2.4m (7.9ft)
Physical
Dimensions (LxHxD) 177mm x 50mm x 45mm
Weight 150g
Color Black or White
Environmental
Radio Frequency Interference
(RFI) Immunity 30 V/m from 10 MHz to 2 GHz
Operating Temperature -20°C to 55°C (-4°F to 131°F)
Storage Temperature -20°C to 60°C (-4°F to 140°F)
Humidity Up to 75%
Note: For indoor use only.
ORDERING INFORMATION
Part Number Description
RK700PR0W00A iREX Request-to-Exit PIR White
RK700PR0B00A iREX Request-to-Exit PIR Black
RK700PRPW00A iREX Plus Request-to-Exit PIR White
RK700PRPB00A iREX Plus Request-to-Exit PIR Black
For UL Standard 294 Compliance:
1. RFI is not verified by UL
2. IQ remote feature is UL listed when it is controlled by Access
Control units and not burglar alarm units.
3. NFPA 101 requires the use of Fail Safe relay mode. Fail Secure
relay mode should be used where accepted under Local
Authority jurisdiction.
4. Setting of low sensitivity at the mounting height of 15ft and 8.5ft
may affect the maximum range.
RISCO Group Limited Warranty
RISCO Group and its subsidiaries and affiliates ("Seller") warrants its products to be free from defects in materials and
workmanship under normal use for 24 months from the date of production. Because Seller does not install or connect
the product and because the product may be used in conjunction with productsnot manufactured by the Seller, Seller
can not guarantee the performance of the security system which uses this product. Sellers obligation and liability
under this warranty is expressly limited to repairing and replacing, at Sellers option, within a reasonable time after the
date of delivery, any product not meeting the specifications. Seller makes no other warranty, expressed or implied, and
makes no warranty of merchantability or of fitness for any particular purpose. In no case shall seller be liable for any
consequential or incidental damages for breach of this or any other warranty, expressed or implied, orupon any other
basis of liability whatsoever.Sellers obligation under this warranty shallnot include any transportation charges or costs
of installation or any liability for direct, indirect, or consequential damages or delay. Sellerdoes not represent that its
product may not be compromised or circumvented; that the product will prevent any persona; injury or property loss by
intruder, robbery, fire or otherwise;or that the product will in all cases provide adequate warning or protection. Buyer
understands that a properly installed and maintained alarm may only reduce the risk of intruder, robbery or fire without
warning, but is not insurance or a guaranty that such will not occur or that there will be no personalinjury or property
loss as a result. Consequentlyseller shall have no liability for any personal injury, property damage or loss based on a
claim that the product fails togive warning. However, if seller is held liable,whether directly or indirectly, for any loss or
damage arising from under this limited warranty or otherwise, regardlessof cause or origin, sellers maximum liability
shall not exceed the purchaseprice of the product, which shall be completeand exclusive remedy against seller. No
employee or representative of Selleris authorized to change this warranty in any way orgrant any other warranty.
WARNING: This product should be tested at least once a week.
Contacting RISCO Group
RISCO Group is committed to customer service and product support. You can contact us through our website
(www.riscogroup.com) or at the following telephone and fax numbers:
United Kingdom
Tel:[phone]
[email protected]
USA
Tel:[phone]
[email protected]
Poland
Tel: [phone]
[email protected]
Italy
Tel: [phone]
[email protected]
Belgium
Tel: [phone]
[email protected]
Israel
Tel: [phone]
[email protected]
Spain
Tel:[phone]
[email protected]
Brazil
Tel:[phone]
[email protected]
France
Tel: [phone]
[email protected]
China
Tel: [phone]
[email protected]
All rights reserved. No part of this document may be reproduced in any form without prior written permission from the
publisher.
© RISCO Group 01/09 5IN700PR B