Ritron OUTPOST RQX-151 User manual

Series OUTPOST®
Owner’s Manual
•For Serial #’s 13250 or Higher – Use Ritron Pub No. 14500056 – “1” Series Owners Manual.
•For Serial #’s 13249 or Lower – Use Ritron Pub No. 14500048 – “1” Series Owners Manual.
Ritron Pub. 14500056 Rev. A 10/05
© 2005-2006 Ritron, Inc. All rights reserved. Ritron, Patriot, Jobcom, OutPost,
GateGuard, Quiet Call and Quick Assist are registered trademarks of Ritron,
Inc. Quick Talk, Liberty and RadioNexus are trademarks of Ritron, Inc.
Call 800-USA-1-USA
For the right Wireless Solutions for your communication needs.
P.O. Box 1998 ·Carmel, Indiana 46082-1998 · 317-846-1201 · Fax: [phone]
Email: HT[email protected]TH · HTwww.ritron.comTH

Series OUTPOST®
Owner’s Manual
•For Serial #’s 13250 or Higher – Use Ritron Pub No. 14500056 – “1” Series Owners Manual.
•For Serial #’s 13249 or Lower – Use Ritron Pub No. 14500048 – “1” Series Owners Manual.
Ritron Pub. 14500056 Rev. A 10/05
© 2005-2006 Ritron, Inc. All rights reserved. Ritron, Patriot, Jobcom, OutPost,
GateGuard, Quiet Call and Quick Assist are registered trademarks of Ritron,
Inc. Quick Talk, Liberty and RadioNexus are trademarks of Ritron, Inc.
Call 800-USA-1-USA
For the right Wireless Solutions for your communication needs.
P.O. Box 1998 ·Carmel, Indiana 46082-1998 · 317-846-1201 · Fax: [phone]
Email: HT[email protected]TH · HTwww.ritron.comTH

1 Series OUTPOST®Wireless Callbox
iHave questions? Call 800-USA-1-USA (800-872-1872) or visit our website at www.ritron.com
T
ABLE OF
C
ONTENTS
..............................................................
Basic Operation 1 SERIES OUTPOST®CALLBOX MODEL NUMBERS................................................1
ABOUT THE 1 SERIES OUTPOST®CALLBOX .........................................................1
OPERATING THE 1 SERIES OUTPOST®CALLBOX WITH FACTORY
DEFAULT SETTINGS............................................................................................2
EXPOSURE TO RADIO FREQUENCY ENERGY ........................................................2
Installation Instructions APPLYING POWER TO THE OUTPOST®CALLBOX...................................................3
FIG-1: Charge Jumper Shown in Charge Position............................................4
POWER MANAGEMENT OPTIONS.........................................................................4
CALLBOX CONTROLS AND CONNECTORS.............................................................5
FIG-2: Callbox Assembly, Controls and Connectors........................................5
FIG-3: XT CALLBOX ASSEMBLY..........................................................................6
BASIC OUTPOST®INSTALLATION INSTRUCTIONS ..................................................7
COVERAGE ........................................................................................................7
XT OUTPOST®INSTALLATION INSTRUCTIONS.......................................................7
FIG-4: XT Callbox Mounting Tabs ...................................................................7
OPTIONAL XT OUTPOST®MOUNTING BRACKET INSTALLATION INSTRUCTIONS.......8
FIG-5: Optional XTMK Mounting Bracket for XT Callbox ................................8
HOW TO SEAL THE ANTENNA ..............................................................................8
Field Programming HOW TO READOUT CURRENT RADIO FREQUENCY & TONE CODES .......................9
HOW TO FIELD PROGRAM FREQUENCY & TONE CODES .....................................10
TABLE 1: PROGRAMMABLE FREQUENCY CODES................................................11
CANADIAN FREQUENCY CODES.........................................................................11
TABLE 2: INTERFERENCE ELIMINATOR PROGRAMMABLE QC TONE CODES .........12
TABLE 3: INTERFERENCE ELIMINATOR PROGRAMMABLE DQC TONE CODES ......12
HOW TO FIELD PROGRAM RADIO FEATURE CODES............................................13
TABLE 4: SINGLE DIGIT RADIO FEATURES CODES .............................................13
TABLE 5: ADVANCED FEATURES CODES ...........................................................14
Programmable Features PROGRAMMABLE OUTPOST®CALLBOX FEATURES .............................................15
Glossary of Terms..........................................................................................15
INTERCOM (ALWAYS-ON) PROGRAMMING..........................................................16
Licensing FCC Licensing................................................................................................17
How to Obtain an FCC Radio License............................................................17
Safety Standards............................................................................................17
INDUSTRY CANADA Regulations..................................................................17
INDUSTRY CANADA License Application......................................................17
Service ...........................................................................................................17
Warranty RITRON, INC. LIMITED WARRANTY..................................................................18
Note: The “6” Series OUTPOST®Callbox features that are not available on the 1 Series include:
Relay Control •
••
•Relay Outputs •
••
•2-Tone Decode •
••
•Sensor Inputs •
••
•DTMF ANI
THANK YOU FOR CHOOSING RITRON
Congratulations on your purchase of the OUTPOST®Callbox. Your new radio is the result of Ritron’s 25+
years of designing, manufacturing, and supplying reliable, professional wireless communication products.
Ritron wireless products will improve the operation, safety, and profitability of any organization by provid-
ing instant voice communications between employees throughout the workplace.

1 Series OUTPOST®Wireless Callbox Basic Operation
Have questions? Call 800-USA-1-USA (800-872-1872) or visit our website at www.ritron.com 1
1 S
ERIES
O
UTPOST
®
C
ALLBOX
M
ODEL
N
UMBERS
............................
VHF MODELS
RQX-151 ........VHF Basic Callbox
RQX-151-XT ..VHF Vandal-Resistant XT Callbox
UHF MODELS
RQX-451 ........UHF Basic Callbox
RQX-451-XT .. UHF Vandal-Resistant XT Callbox
The model number appears on the serial label located
behind the removable faceplate of the basic Callbox
enclosure. On XT models the model number is located
on the bottom of the fiberglass reinforced vandal-
resistant enclosure.
VHF radios are designed to operate within the 15 MHz
band between factory standard 150 and 165 MHz.
UHF radios are designed to operate within the 20 MHz
band between factory standard 450 and 470 MHz.
A
BOUT THE
1 S
ERIES
O
UTPOST
®
C
ALLBOX
......................................
The 1 Series OUTPOST®Callbox is a 2-way radio
transceiver used to communicate directly with portable,
mobile and stationary radios, or through radio repeaters with
Ritron PC Programming software. Each callbox is equipped
with the following features or capabilities
•
••
•Field programming. Field programming allows you to
quickly program your radio in the field without the need for
a PC programmer. Each radio can be field programmed to
one of 26 VHF or 77 UHF channel table frequencies, and
one of 51 QC or 104 DQC interference eliminator codes.
•
••
•VHF “License Free” frequencies. VHF models can be
programmed from a list of 5 MURS frequencies that do
not require FCC licensing.
•
••
•154 interference eliminator codes. Quiet Call (QC) and
Digital Quiet Call (DQC) codes can be programmed to
eliminate other radio users not in your workgroup. For
compatibility, new radios should be programmed with the
same codes.
•
••
•Wide or Narrow Band Operation The radio can be
programmed for wide or narrow operation by selecting
from a variety of field programmable table frequencies, or
custom frequencies via special Ritron PC programming
software by the factory or your Ritron dealer.
•
••
•Normal or High Microphone Gain. Field and PC
programmable to normal or high microphone gain.
•
••
•Volume Level. Field programmable to any one of 5
preset levels and PC programmable to 2 – 100% volume
level.
•
••
•High/Low Power Output The callbox can be field
programmed for transmitter power output.
•VHF: 1 Watt
•UHF: 1 Watt or 2* Watt
* See “Special Note” on page 3
•
••
•Battery Powered The 1 Series OUTPOST®Callbox can
be powered by six (6) Alkaline D-cell batteries for a
completely wireless installation. The D-cell batteries can
power the radio for up to one (1) year or 7,000
transmissions. If external 12 VDC is used, and battery
back-up is required, DO NOT use alkaline batteries. Use
rechargeable NiCd batteries and the Charge Jumper must
be in the Charge position.
•
••
•External Power +12 VDC Capable The Basic and XT
models are capable of being power by an external +12
VDC source. This method of powering the callbox allows
the radio to remain ON at all times, like an intercom.
Automatic Turn Off must be DISABLED via Field or PC
programming.
•
••
•Low Battery Alert The callbox will transmit an Alert Tone
at the end of each transmission when the batteries
approach end-of-life. This allows sufficient time for you to
replace the batteries and assure uninterrupted service.
•
••
•+12 VDC Power Fail Alert This feature can be enabled
via Field or PC programming. The callbox will transmit an
Alert Tone if it detects loss of +12 VDC power. This Alert
Tone replaces a Low Battery Alert. The radio
automatically continues to transmit an Alert Tone once
every hour (unless programmed for Automatic Turn Off)
until +12 VDC is restored or the batteries are depleted.
•
••
•“Automatic Turn-Off” or “Intercom” Operation The 1
Series OUTPOST®Callbox can operate in the standard
“Automatic Turn-Off” mode (Factory Default), where the
radio is normally OFF until the Call Button is pressed, or
can be Field or PC programmed for “Intercom” operation
where the radio is always ON. See “External Power +12
VDC Capable” feature above.
•
••
•DTMF or Selcall ANI 3-7 digit codes can be transmitted
at the beginning of each message for radio identification.
Basic Callbox XT Callbox

1 Series OUTPOST®Wireless Callbox Basic Operation
2Have questions? Call 800-USA-1-USA (800-872-1872) or visit our website at www.ritron.com
O
PERATING THE
1 S
ERIES
O
UTPOST
®
C
ALLBOX WITH
F
ACTORY
D
EFAULT
S
ETTINGS
......................................................................
The 1 Series OUTPOST®Callbox Factory Default setting
is with Automatic Turn Off ENABLED. This means the
callbox is OFF and will not receive a call until the callbox
first initiates a call.
In Automatic Turn Off mode the callbox automatically
shuts off whenever there is “no activity” for ten (10)
seconds.
To Initiate a Call
Press and hold the ON/PTT Button. The callbox will send
a unique CALL TONE to alert radio equipped personnel.
This CALL TONE will also be heard at the callbox.
Listen for the “beep”, then begin speaking into the MIC.
For best communication, the caller should be 3 feet or
less from the microphone.
To Receive a Call
1. When you have finished speaking, release the
ON/PTT Button.
2. Any reply will be heard through the callbox speaker.
If a call is not received within 10 seconds of
releasing the ON/PTT Button and there is no activity
on the channel, the callbox will sound a low double
tone and turn-off automatically. This automatic turn-
off feature is designed to conserve battery life.
Operation Notes
The 1 Series OUTPOST®must be powered with D-cell
Alkaline batteries ONLY, or alternatively, with an external
12 VDC power supply, order Ritron model RPS-EXPO
110 VAC to 12 VDC cube power supply.
If there has been no activity for 10 seconds, i.e. either
the ON/PTT Button has not been pressed or a call has
not been received, the unit automatically shuts OFF.
Low Battery Alert
The callbox will transmit an Alert Tone at the end of each
transmission when the batteries approach end-of-life. This
allows sufficient time for you to replace the batteries and
assure uninterrupted service.
E
XPOSURE TO
R
ADIO
F
REQUENCY
E
NERGY
.....................................
These products generate radio frequency (RF) energy
when the ON/PTT button on the front of the unit is
depressed. These products have been evaluated for
compliance with the maximum permissible exposure
limits for RF energy at the maximum power rating of the
unit when using antennas available from Ritron.
These products are not to be used by the general public
in an uncontrolled environment unless compliance with
the Uncontrolled/General Population limits for RF
exposure can be assured.
Antennas other than those available from Ritron listed
below have not been tested for compliance and may or
may not meet the exposure limits at the distances
given. Higher gain antennas are capable of generating
higher fields in the strongest part of their field and
would, therefore, require a greater separation from the
antenna.
RQX-451: For both the AFB-1545 and RAM-1545
antennas, at the 20 cm (7.9 inches) minimum expected
separation distance and greater, the maximum RF
exposure is well below the General
Population/Uncontrolled limits.
RQX-151: To comply with the General
Population/Uncontrolled limits, all persons must be at
least 7.9 inches (20 cm) from the AFB-1545 antenna
which is supplied by RITRON to be attached directly to
the top of the unit. For the Ritron RAM-1545 magnet
mount antenna, which can be located away from the
unit, all persons must be at least 10.8 inches (28 cm)
from the antenna.
To limit exposure to RF energy to levels below the limit,
please observe the following:
• Use only the antenna(s) available from Ritron for these
models. DO NOT operate the radio without an
antenna.
• Keep talk times as short and infrequent as possible.
DO NOT depress the ON/PTT button when not actually
wishing to transmit. These radios are equipped with an
internal timer to limit continuous transmit times.
• When transmitting, make certain that the distance
limits for the particular model in use are observed.
•DO NOT allow children to operate the radio.
When used as directed, this series of radios is designed to
comply with the FCC’s RF exposure limits for
“Uncontrolled/General Population”. In addition, they are
designed to comply with the following Standards and
Guidelines:
• FCC OET Bulletin 65, Edition 97-01, Supplement C,
Evaluating Compliance with FCC Guidelines for Human
Exposure to Radio Frequency Electromagnetic Fields.
• American National Standards Institute (C95.1-1992),
IEEE Standard for Safety Levels with Respect to Human
Exposure to Radio Frequency Electromagnetic Fields, 3
kHz to 300 GHz.
•American National Standards Institute (C95.3-1992),
IEEE Recommended Practice for the Measurement of
Potentially Hazardous Electromagnetic Fields-RF and
Microwave.

1 Series OUTPOST®Wireless Callbox Installation Instructions
Have questions? Call 800-USA-1-USA (800-872-1872) or visit our website at www.ritron.com 3
A
PPLYING
P
OWER TO THE
O
UTPOST
®
C
ALLBOX
..............................
The Callbox may be powered:
•by six (6) D-cell batteries
•through an external +12 VDC source
•or both (refer to Battery Powered on page 1)
Powering the callbox from internal batteries will allow for
an installation that does not require wiring to an external
source of power. Powering the callbox by an external
source will allow the unit to remain ON, like an intercom*.
To provide a useful amount of battery life, one of two
battery saver options should also be used. See “POWER
MANAGEMENT OPTIONS” on page 4.
* Automatic Turn Off must be DISABLED via Field or
PC Programming.
Using Internal Batteries
Six (6) D-cell batteries may be installed in the internal
battery holder for a no trenching, no wires required
installation. If internal batteries are used, a LOW battery
alert tone will be transmitted when the battery voltage
drops below a programmed value. The LOW battery tone
notifies personnel that the batteries should be replaced.
SPECIAL NOTE: We recommend not operating the UHF
model set to High Power when using Alkaline batteries.
Due to the nature of alkaline batteries your transmit
power output will decrease rapidly as the batteries are
depleted.
Using External +12 VDC Power with Battery Back-up
Note: an additional hole, strain relief, and conduit will
need to be installed into the callbox.
The unit may be powered by an external source of +12
VDC. This source should be filtered, with minimum noise
and hum, and capable of supplying at least 1 Ampere.
Order Ritron model RPS-EXPO 110 VAC to 12 VDC
cube power supply.
Factory Default programming of the callbox is optimized
for battery power operation. The External +12VDC Power
Fail Alert option is NOT ENABLED.
It is recommended that if an external source of power is
used, that the internal batteries be installed as a back-up
against loss of power. If this option is chosen, we
recommend that the “External +12 VDC Power Fail Alert”
feature be ENABLED via Field or PC programming.
How the Callbox Operates:
If External +12 VDC Power Fail Alert Feature is NOT
ENABLED:
•Radio always checks for LOW battery or DEAD battery
condition when the radio is ON.
•If LOW battery is detected, a single Alert Tone will be
transmitted at the end of the transmission.
•Radio does
NOT automatically transmit a LOW battery
tone. The callbox must be ON and Alert Tone is only
sent at the end of a transmission.
•If DEAD battery is detected, the radio ceases all
operation. A DEAD battery tone is heard on the callbox
speaker and the radio will turn OFF.
If External +12 VDC Power Fail Alert Feature is
ENABLED:
•Radio always checks for External +12 VDC when the
radio is ON. If loss of External +12 VDC is detected
while the radio is in standby: a single Alert Tone will be
transmitted immediately.
•If loss of External +12 VDC is detected while the radio
is in receive: a single Alert Tone will be
transmitted after the received message is complete.
•If loss of External +12 VDC is detected while the radio
is in transmit: a single Alert Tone will be transmitted at
the end of the transmission.
•Once loss of External +12 VDC is detected and the
Alert Tone is transmitted, the radio will automatically
send the Alert Tone once every hour until External +12
VDC is restored or the batteries are exhausted. If radio
is set for Automatic Turn-Off (default setting) this
hourly alert will NOT occur.
•If Dead battery is detected the radio ceases all
operation, a DEAD battery tone is heard on the callbox
speaker and the radio will turn OFF.
!

1 Series OUTPOST® Wireless Callbox Installation Instructions
4Have questions? Call 800-USA-1-USA (800-872-1872) or visit our website at www.ritron.com
A
PPLYING
P
OWER TO THE
O
UTPOST
®
C
ALLBOX
(C
ONTINUED
)
.............
Using Rechargeable Batteries for Battery Back-up
If rechargeable NiCd batteries are used for battery
backup the “Charge Jumper” must be placed into the
“charge” position as shown in FIG-1 below.
! ! CAUTION ! !
If rechargeable batteries are NOT used for battery
backup, be sure the “Charge Jumper” is NOT in the
“charge position. Charging Alkaline batteries will damage
the cells and reduce battery life! DO NOT use Alkaline
batteries for back-up battery with external 12 VDC
power.
P
OWER
M
ANAGEMENT
O
PTIONS
..................................................
There are three power management options available to
the 1 Series OUTPOST®Callbox:
Automatic Turn-Off (Field or PC Programmable)
In this mode, the callbox will automatically turn itself off
after a programmed period of no activity (no
transmissions made and no calls received) has
elapsed. Once the unit has turned itself off, it can only be
turned back on by depressing the ON/PTT Button. The
programmed period of no activity necessary before the
unit turns itself off is called the RQX Reset Time. RQX
Reset Time and Automatic Turn-Off can both be Field
programmed, or PC programmed by the factory or your
Ritron dealer via the Ritron RQX Series PC Programmer.
Automatic Turn-Off mode is the factory default mode for
power management with an RQX Reset Time of 10
seconds.
Battery Saver (PC Programmable Only)
This mode is similar to the Automatic Turn-Off mode
except that the unit does NOT turn itself off after the
RQX Rest Time has elapsed. Instead it reverts to a mode
where the unit goes to sleep and periodically wakes up to
test for receive activity on the channel. The Sleep Period
(called Battery Saver Sleep Time) can be set using the
Ritron RQX Series PC Programmer to between 0.5 and 8
seconds. Longer sleep times result in better battery life,
but increase the chances that activity on the channel
may be missed. The unit will come out of this mode when
activity is detected during the wake-up period or if the
ON/PTT button is pressed. The Automatic Turn-Off and
Battery Saver modes cannot be used together.
Neither “Automatic Turn-Off” nor “Battery Saver”
Used (Field or PC Programmable)
If neither Automatic Turn-Off nor Battery Saver are used
the unit will consume the largest amount of current, but is
always ready to instantly receive messages. This mode
should only be considered if an external source of +12
VDC is available (see “Using External +12 VDC Power
with Battery Back-up” on page 3).
FIG-1: Charge Jumper Shown in Charge Position
Charge Jumper in
Char
g
e
p
osition

1 Series OUTPOST®Wireless Callbox Installation Instructions
Have questions? Call 800-USA-1-USA (800-872-1872) or visit our website at www.ritron.com 5
C
ALLBOX
C
ONTROLS AND
C
ONNECTORS
......................................
Antenna Connector
The antenna radiates radio signals. Before using the 1
Series OUTPOST®Callbox, make sure the antenna is
securely fastened into the 50ΩBNC antenna connector.
If the OUTPOST®is to be used outdoors, see page 8for
instructions on properly sealing the antenna connector.
RF Mating Connectors
An internal cable from the antenna connector is
terminated into a phono style connector for connection to
the radio circuit board.
Captive Plastic Case Screws
A captive plastic case screw is located in each corner of
the case front. These four (4) screws are used to secure
the case front containing the radio, to the case back that
contains the batteries.
Charge Jumper
The charge jumper can be set to trickle charge re-
chargeable backup batteries (see “Using Re-chargeable
Batteries for Battery Back-up” on page 4).
12 VDC Input Connector
The 6-pin, plarized connector allows connection of an
external +12 VDC input.
Speaker Connector
The internal speaker is connected to the radio printed
circuit board with a polarized connector.
On/PTT Connector
The ON/PTT switch is connected to the radio printed
circuit board with a polarized connector.
Pre-Drilled Mounting Holes
Mounting holes located in the 4 corners of the case back
are pre-drilled for mounting to a plate, wall or post. Once
mounted, the case front is secured to the case back
through these same threaded holes.
RJ-11 Program Cable Connector
An RJ-11 style connector is used to connect the cable
from the PC programmer to the radio.
Program Button
A small, momentary pushbutton is used for field
programming the OUTPOST®Callbox.
Program Display
A single digit LED display is used during field
programming of the radio.
Battery Holder
The battery holder inside the case back is used for the
installation of 6 D-cell Alkaline or NiCd batteries. Refer to
the diagram below, or the labels beneath the cells, for
correct installation of the batteries.
Battery Mating Connectors
Polarized, 2-pin mating connectors are used to connect
the batteries to the radio circuit board.
+12 VDC Input
Connector
RF Mating Connectors
50Ω
ΩΩ
ΩBNC Antenna Connector
Captive Plastic Case
Screws (4 Corners)
Program Button
Program Display
Battery Mating
Connectors
RJ-11 Program Cable Connector
Battery Holder with
D-Cell Batteries In-
stalled
Pre-Drilled Mounting
Holes
(
4 Corners
)
FIG-2: Callbox Assembly, Controls and Connectors
Charge Jumper
Speaker Connector
On/PTT Connector

1 Series OUTPOST®Wireless Callbox Installation Instructions
6Have questions? Call 800-USA-1-USA (800-872-1872) or visit our website at www.ritron.com
F
IG
: 3 XT C
ALLBOX
A
SSEMBLY
....................................................
XT Callbox 2-Wire Interface Cable
Wire Description
Red External 12 VDC “+” input
Black External 12 VDC “-” input
2-Conductor
Interface Cable
Captive Plastic
Case Screws (4 Corners) RF Mating
Connectors
Battery Mating
Connectors
On/PTT Switch
Front Plate
(Bottom Edge)
Threaded Inserts for Front Plate
Mounting (4 Corners) Internal Antenna
Battery Holder with
D-Cell Batteries Installed
Charge
Jumper
On/PTT
Connector
+12 VDC Input
Connector

1 Series OUTPOST®Wireless Callbox Installation Instructions
Have questions? Call 800-USA-1-USA (800-872-1872) or visit our website at www.ritron.com 7
B
ASIC
O
UTPOST
®
I
NSTALLATION
I
NSTRUCTIONS
...............................
The Basic model can be mounted to virtually any surface
with four (4) #6 panhead screws. Choose a type of screw
thread and screw length which will hold firmly in the
surface to which the unit will be mounted.
MOUNTING the Basic OUTPOST®: (Refer to FIG-2)
1. Loosen the four (4) captive screws in the front
corners of the case and separate the case front from
the case back. These screws are captive to the
housing; to prevent damaging them, DO NOT
remove the screws from the housing.
2. Install 6 D-cell Alkaline or NiCd batteries into the
battery holder. Refer to FIG-2, or the labels beneath
the cells, for correct installation of the batteries.
3. If required, program the radio. Refer to the
programming section of this manual for details.
4. Disconnect the RF mating connectors and the
battery mating connectors. Set the case front
containing the radio circuit board aside.
5. Insert a #6 panhead screw into each of the four (4)
corner holes in the Basic model case back. Position
the case back in the chosen installation location and
secure it in place with the four screws.
CAUTION
DO NOT drill or penetrate the Basic
model case with any additional holes. Use only the
pre-drilled mounting holes.
6. Re-connect the RF mating connectors and the
battery mating connectors between the case front
and case back.
7. Fasten the case front to the case back with the four
(4) captive screws. DO NOT over-tighten the plastic
screws to prevent damage.
8. Insert, rotate and lock the antenna onto the antenna
connector. Orient the antenna vertically.
9. If the Basic model is to be used outdoors, it is
imperative that the antenna connector be sealed
with sealing tape after the antenna has been
installed. Use Grainger #2A-459, Radio Shack #278-
1647, or equivalent seal tape. Refer to “Sealing the
Antenna” instructions in this manual.
10. To install the message placard, align the center of
the hole over the ON/PTT Button, and the
mushroom-head fastener strips on the back of the
placard with the strips on the front of the Basic
model case. Press firmly to interlock the strips,
snapping the panel into position.
XT O
UTPOST
®
I
NSTALLATION
I
NSTRUCTIONS
...................................
The XT model can be mounted to virtually any surface with four (4) ¼” diameter fasteners, not included. Choose a type
of screw thread and screw length which will hold firmly in the surface to which the unit will be mounted.
MOUNTING the XT OUTPOST®WITH INCLUDED MOUNTING TABS: ( Refer to FIG-3 and FIG-4)
1. Place the XT callbox on a flat work surface. Remove the front faceplate from the
callbox. The faceplate is secured to the case with 4 vandal-resistant
buttonhead, Torx screws. Use the T-25 Torx bit included with the radio to
remove these screws.
2. Remove the “Mounting Tabs” kit secured to the inside of the XT callbox case.
3. Loosen the (4) captive screws in the front corners of the internal XT callbox
case and separate the case front from the case back. The screws are captive to
the housing; to prevent damaging them, DO NOT remove the screws from the
housing.
4. Install 6 D-cell Alkaline or NiCd batteries into the battery holder. Refer to FIG-3,
or the labels beneath the cells, for correct installation of the batteries.
5. If required, program the radio. Refer to the programming section of this manual
for details.
6. Fasten the internal case front to the case back with the four (4) captive screws.
To prevent damage, do not over-tighten the plastic screws.
7. Re-fasten the front faceplate to the radio with the 4 buttonhead Torx screws.
8. Install the four (4) mounting tabs to the back of the XT callbox case as shown in
FIG-4 with the #10-32 bolts provided. The mounting tabs can be installed vertically, as shown, or horizontally.
9. Position the XT callbox in the chosen installation location and secure it in place with four (4) screws through the
mounting tabs.
!
COVERAGE Depending on the unit location and installation, the 1 Series OUTPOST
®
set for 1 Watt can cover
up to 1 mile line of sight. To increase range, use an external antenna that is mounted higher.
Contact Ritron for a RAM-1545 Magnet Mounted Antenna. Refer to Special Note on page 3.
FIG-4: XT Callbox
Mounting Tabs

1 Series OUTPOST®Wireless Callbox Installation Instructions
8Have questions? Call 800-USA-1-USA (800-872-1872) or visit our website at www.ritron.com
OPTIONAL XT O
UTPOST
®
M
OUNTING
B
RACKET
I
NSTALLATION
I
NSTRUCTIONS
............................................................................
The optional XT Mounting Bracket (order part # XTMK)
can be attached to the callbox for special applications with
two (2) ¼” diameter fasteners, NOT included. Choose a
type of screw thread and screw length which will will
fasten the callbox securely to the mounting surface.
MOUNTING the OPTIONAL XT OUTPOST®BRACKET:
Refer to FIG-5 :
1. Using the XTMK bracket as a template, mark the two
(2) holes #2 (see FIG-5) on the mounting surface you
intend to fasten the bracket.
2. Find a flat work surface and using the included four
(4) button head tamper resistant fasteners, attach the
XTMK bracket to the existing holes on the back of the
XT callbox (holes #1), as shown in FIG 5.
3. Secure the XTMK bracket to the mounting surface
using holes #2 and two (2) ¼” fasteners (NOT
included), as shown in FIG-5. Make sure mounting
surface and fasteners are capable of supporting the
total weight of the XT callbox.
H
OW TO
S
EAL THE
A
NTENNA
........................................................
If the Basic OUTPOST®Callbox is to be used outdoors it is imperative
that the entire antenna connection be sealed with seal tape to provide
proper operation and prevent voiding warranty.
Seal tape can be purchased at most Industrial Supply Stores,
Hardware and Home Center Stores, or Electronic Supply Stores.
Regarless of the antenna used, it is always best to weatherproof the
antenna connection using seal tape.
NOTICE
Failure to follow these instructions will cause damage to the
product, prevent proper sealing of the enclosure and will void
the Manufacturers Warranty.
Applying Seal Tape:
1. Attach the antenna to the 50ΩBNC connector on the Basic
OUTPOST®Callbox enclosure.
2. Begin wrapping seal tape at the base of the antenna connector
such that it is sealed to the enclosure top.
3. Overlap the seal tape as you tightly wrap upward around the
connector and antenna. Continue to overlap seal tape around the
connector base, past the articulated portion of the antenna and
several inches up the thin, shiny section of the antenna.
FIG-5: Optional XTMK Mounting Bracket
For XT Callbox
AFB-1545 Antenna
before sealing
Wrap tape
from bottom,
sealing to
enclosure.
Overlap
sealing tape
(1) inch be-
yond the
rigid section
of the an-
tenna
AFB-1545 Antenna
after sealing

1 Series OUTPOST®Wireless Callbox Field Programming
Have questions? Call 800-USA-1-USA (800-872-1872) or visit our website at www.ritron.com 9
H
OW TO
R
EADOUT
C
URRENT
R
ADIO
F
REQUENCY
& T
ONE
C
ODES
.....
Make sure your record the programming content of your radio before proceeding
1. Loosen the (4) captive screws in the front corners of the case. These screws are captive to the housing; to prevent
damaging them, DO NOT remove the screws from the housing.
2. Separate the case front from the case back, leaving the battery connected to the radio. Make sure the unit has
batteries installed. NOTE: The voltage of the batteries must be greater than 6 VDC to program properly.
3. Press and release the ON/PTT button on the front of the Callbox to turn the radio on.
4. Press and RELEASE the Program button (See FIG-2 on page 5 for location). The radio will immediately begin to
display a series of four digits; with each digit separated by a hyphen.
5. Write down the four (4) digits. The first two digits indicate the frequency code and the last two digits the tone code;
see Table 1 and Table 2 on pages 11 and 12. In this example an RQX-451 is programmed to operate on the
“Brown Dot” frequency of 464.500 MHz (Frequency code “04”) with 100.0 Hz tone (Tone code “12”).
6. If a 5th digit is displayed, the channel has been programmed for DQC and the last three digits indicate the DQC
code; see Table 3 on page 12. In this example an RQX-451 was programmed to operate on the “Brown Dot”
frequency of 464.500 MHz (Frequency code “04”) with a DQC code of “723”.
7. If the channel is PC programmed with any frequency or tone not listed in Table 1, Table 2 or Table 3 on pages 11
and 12, the radio will sound the error tone on contents read out and display an "E". The PC programmer will be
required to readout the radios frequency and tone programming.
8. Normal radio operation resumes after the programming information has been displayed.
FREQUENCY CODE DQC CODE
FREQUENCY CODE TONE CODE

1 Series OUTPOST®Wireless Callbox Field Programming
10 Have questions? Call 800-USA-1-USA (800-872-1872) or visit our website at www.ritron.com
04
12
H
OW TO
F
IELD
P
ROGRAM
F
REQUENCY
& T
ONE
C
ODES
...................
To match other radios, the owner can select Frequency, Tone and DQC Codes from Table 1, Table 2 and Table 3on
pages 11 and 12. In our example, we will program an RQX-451 to operate on the "Brown Dot" frequency of 464.500
MHz with 100.0 Hz tone.
1. Refer to Table 1 on page 11 to determine the two-digit frequency code and write it down.
2. Refer to Table 2 on page 12 to determine the two-digit tone code for 100.0 Hz and write it
down.
3. Loosen the (4) captive screws in the front corners of the case. These screws are captive to the
housing; to prevent damaging them, DO NOT remove the screws from the housing.
4. Separate the case front from the case back, leaving the battery connected to the radio. Make
sure the unit has batteries installed.
NOTE: The voltage of the batteries must be greater than 6 VDC to program properly.
5. Press and release the ON/PTT button on the front of the unit to turn the radio on.
6. Press and HOLD the Program Button (See FIG-2 on page 5 for location). A "P" will appear on
the program display as you enter program mode and the radio will beep rapidly.
7. Release the program button after the beeping has stopped. The radio will emit a triple beep
indicating that the radio is in program mode and a hyphen will appear on the program display.
8. Enter the 1st digit of the frequency code by clicking the Program button until the program
display shows the desired number. Pause—the radio will sound a low tone and show a
hyphen across the center of the display to indicate that it is ready to accept the next digit.
9. Enter the 2nd digit of the frequency code by clicking the Program button until the program
display shows the desired number. Pause—the radio sounds a low tone and will show a
hyphen across the center of the display to indicate that it is ready to accept the next digit.
10. Enter the 1st digit of the tone code (or 1st digit of the DQC code) by clicking the Program button
until the program display shows the desired number. Pause—the radio sounds a low tone and
will show a hyphen across the center of the display to indicate that it is ready to accept the
next digit.
11. Enter the 2nd digit of the tone code (or 2nd digit of the DQC code) by clicking the Program
button until the program display shows the desired number. Pause—the radio sounds a low
tone and will show a hyphen across the center of the display to indicate that it is ready to
accept the next digit.
12. FOR DQC CODES ONLY – Enter the 3rd digit of the DQC code by clicking the Program button
until the program display shows the desired number. Pause—the radio sounds a low tone and
will show a hyphen across the center of the display to indicate that it is ready to accept the
next digit.
13. Press and release the ON/PTT button to save your programming. A triple beep will sound to
indicate that programming was successful and a hyphen will appear on the program display.
The radio is now ready for another program entry..
NOTE: An error tone will sound if you attempt to save an incorrect code, an "E" will appear on
the display and the radio will turn off. Check the digits you are attempting to enter, then start
over.
14. Once you have made your final program entry, press the ON/PTT button a second time to turn
the radio off. Turn the radio back on for normal operation.

1 Series OUTPOST®Wireless Callbox Field Programming
Have questions? Call 800-USA-1-USA (800-872-1872) or visit our website at www.ritron.com 11
T
ABLE
1: P
ROGRAMMABLE
F
REQUENCY
C
ODES
..............................
UHF Business Band
Code Frequency ColorDot BW
01 467.7625 J 25
02 467.8125 K 25
03 464.5500 Yellow Dot 25
04 464.5000 Brown Dot 25
05 467.8500 Silver Star 25
06 467.8750 Gold Star 25
07 467.9000 Red Star 25
08 467.9250 Blue Star 25
09 469.2625 25
10 462.5750 White Dot 25
11 462.6250 Black Dot 25
12 462.6750 Orange Dot 25
13 464.3250 25
14 464.8250 25
15 469.5000 25
16 469.5500 25
17 463.2625 25
18 464.9125 25
19 464.6000 25
20 464.7000 25
21 462.7250 25
22 464.5000 12.5
23 464.5500 12.5
24 467.7625 12.5
25 467.8125 12.5
26 467.8500 12.5
27 467.8750 12.5
28 467.9000 12.5
29 467.9250 12.5
30 461.0375 12.5
31 461.0625 12.5
32 461.0875 12.5
33 461.1125 12.5
34 461.1375 12.5
35 461.1625 12.5
36 461.1875 12.5
37 461.2125 12.5
38 461.2375 12.5
39 461.2625 12.5
UHF Business Band
Code Frequency ColorDot BW
40 461.2875 12.5
41 461.3125 12.5
42 461.3375 12.5
43 461.3625 12.5
44 462.7625 12.5
45 462.7875 12.5
46 462.8125 12.5
47 462.8375 12.5
48 462.8625 12.5
49 462.8875 12.5
50 462.9125 12.5
51 464.4875 12.5
52 464.5125 12.5
53 464.5375 12.5
54 464.5625 12.5
55 466.0375 12.5
56 466.0625 12.5
57 466.0875 12.5
58 466.1125 12.5
59 466.1375 12.5
60 466.1625 12.5
61 466.1875 12.5
62 466.2125 12.5
63 466.2375 12.5
64 466.2625 12.5
65 466.2875 12.5
66 466.3125 12.5
67 466.3375 12.5
68 466.3625 12.5
69 467.7875 12.5
70 467.8375 12.5
71 467.8625 12.5
72 467.8875 12.5
73 467.9125 12.5
74 469.4875 12.5
75 469.5125 12.5
76 469.5375 12.5
77 469.5625 12.5
VHF Business Band
Code Frequency ColorDot BW
03 151.625 Red Dot 25
04 151.955 Purple Dot 25
05 151.925 25
06 154.540 25
07 154.515 25
08 154.655 25
09 151.685 25
10 151.715 25
11 151.775 25
12 151.805 25
13 151.835 25
14 151.895 25
15 154.490 25
16 151.655 25
17 151.745 25
18 151.865 25
24 151.700 12.5
25 151.760 12.5
26 152.700 25
VHF MURS**
Code Frequency ColorDot BW
01 154.600 Green Dot 25
02 154.570 Blue Dot 25
19 151.820 MURS 12.5
20 151.880 MURS 12.5
21 151.940 MURS 12.5
22 154.600 MURS 12.5
23 154.570 MURS 12.5
Notes
** MURS frequencies do not require
an FCC license. All other fre-
quencies require an FCC license.
•BW is the bandwidth in kHz.
•12.5 kHz indicates a narrow band
channel, 25 kHz indicates a wide
band channel.
C
ANADIAN
F
REQUENCY
C
ODES
..................................................
Canada Models
UHF Business Band
Code Frequency ColorDot BW
01 458.6625 25
02 469.2625 25
Canada Models
VHF Business Band
Code Frequency ColorDot BW
01 151.055 25
02 151.115 25
British Columbia Models
VHF Business Band
Code Frequency ColorDot BW
01 154.100 25
02 158.940 25

1 Series OUTPOST®Wireless Callbox Field Programming
12 Have questions? Call 800-USA-1-USA (800-872-1872) or visit our website at www.ritron.com
T
ABLE
2: I
NTERFERENCE
E
LIMINATOR
P
ROGRAMMABLE
QC T
ONE
C
ODES
......................................................................
Code Frequency
01 67.0
02 71.9
03 74.4
04 77.0
05 79.7
06 82.5
07 85.4
08 88.5
09 91.5
10 94.8
11 97.4
12 100.0
13 103.5
Code Frequency
14 107.2
15 110.9
16 114.8
17 118.8
18 123.0
19 127.3
20 131.8
21 136.5
22 141.3
23 146.2
24 151.4
25 156.7
26 162.2
Code Frequency
27 167.9
28 173.8
29 179.9
30 186.2
31 192.8
32 203.5
33 210.7
34 218.1
35 225.7
36 233.6
37 241.8
38 250.3
39 69.4
Code Frequency
40 159.8
41 165.5
42 171.3
43 177.3
44 No Tone
45 183.5
46 189.9
47 196.6
48 199.5
49 206.5
50 229.1
51 254.1
T
ABLE
3: D
IGITAL
I
NTERFERENCE
E
LIMINATOR
P
ROGRAMMABLE
DQC
TONE
C
ODES
...................................................................
Code
023
025
026
031
032
036
043
047
051
053
054
065
071
Code
072
073
074
114
115
116
122
125
131
132
134
143
145
Code
152
155
156
162
165
172
174
205
212
223
225
226
243
Code
244
245
246
251
252
255
261
263
265
266
271
274
306
Code
311
315
325
331
332
343
346
351
356
364
365
371
411
Code
412
413
423
431
432
445
446
452
454
455
462
464
465
Code
466
503
506
516
523
532
546
565
606
662
612
624
627
Code
631
632
645
654
664
703
712
723
731
732
734
743
754

1 Series OUTPOST®Wireless Callbox Field Programming
Have questions? Call 800-USA-1-USA (800-872-1872) or visit our website at www.ritron.com 13
804
H
OW TO
F
IELD
P
ROGRAM
F
EATURE
C
ODES
....................................
The 1 Series OUTPOST®Callbox can be field programmed for a number of simple and advanced features. Refer to
Table 4 below for the simple, single digit codes available for field programming. Refer to Table 5 for the advanced
three digit codes available for field programming. In our example we will program an RQX-451 for an RQX Reset Time
of 30 seconds.
1. Refer to Table 5 to determine the three-digit feature code and write it down.
2. Loosen the (4) captive screws in the front corners of the case. These screws are captive to the
housing; to prevent damaging them, DO NOT remove the screws from the housing.
3. Separate the case front from the case back, leaving the battery connected to the radio. Make
sure the unit has batteries installed.
NOTE: The voltage of the batteries must be greater than 6 VDC to program properly.
4. Press and release the ON/PTT button on the front of the unit to turn the radio on.
5. Press and HOLD the Program Button (See FIG-2 on page 5 for location). A "P" will appear on
the program display as you enter program mode and the radio will beep rapidly.
6. Release the program button after the beeping has stopped. The radio will emit a triple beep
indicating that the radio is in program mode and a hyphen will appear on the program display.
7. Enter the 1st digit of the feature code by clicking the Program button until the program display
shows the desired number. Pause—the radio will sound a low tone and show a hyphen across
the center of the display to indicate that it is ready to accept the next digit.
NOTE: If entering a simple, single digit code skip to step 10.
8. Enter the 2nd digit of the feature code by clicking the Program button until the program display
shows the desired number. Pause—the radio sounds a low tone and will show a hyphen
across the center of the display to indicate that it is ready to accept the next digit.
9. Enter the 3rd digit of the feature code by clicking the Program button until the program display
shows the desired number. Pause—the radio sounds a low tone and will show a hyphen
across the center of the display to indicate that it is ready to accept the next digit.
10 Press and release the ON/PTT button to save your programming. A triple beep will sound to
indicate that programming was successful and a hyphen will appear on the program display.
The radio is now ready for another program entry.
NOTE: An error tone will sound if you attempt to save an incorrect code, an "E" will appear on
the display. Check the digits you are attempting to enter, then re-enter.
11. Once you have made your final program entry, press the ON/PTT button a second time to turn
the radio off. Turn the radio back on for normal operation.
T
ABLE
4: S
INGLE
D
IGIT
R
ADIO
F
EATURE
C
ODES
...........................
Code Feature Default Description
1
2
3 Volume Level – Medium √Sets Volume level to 50%
4 Volume Level – High Sets Volume level to 100%
5
6
7 Transmit Low Pwr (1 W) √
8 Transmit High Pwr (2 W) UHF Mode Only: Refer to Special Notice on page 3 regarding Alkaline
Battery usage.
9 Call Tone ON √When PTT button is initially pressed a Call Tone will be transmitted.
0 Call Tone OFF
√The Callbox is set from the factory with these options enabled.

1 Series OUTPOST®Wireless Callbox Field Programming
14 Have questions? Call 800-USA-1-USA (800-872-1872) or visit our website at www.ritron.com
T
ABLE
5: A
DVANCED
F
EATURE
C
ODES
.........................................
Code Feature Default Description
RQX Reset Time
801 5 seconds RQX Reset Time is the length of time the RQX Callbox can remain
802 10 seconds √inactive (not receiving or transmitting) before it automatically shuts off.
803 20 seconds
804 30 seconds
805 45 seconds
806 1 minute
807 2 minutes
808 3 minutes
809 4 minutes
Special Features
821 Reset to Factory Defaults Resets Callbox to Factory default programming.
822 Display Radio Revision Callbox will display a sequence of 6 digits to identify operating code
revision. This is helpful when troubleshooting the radio.
823 Enable External +V Enables the External +V “Loss of power” notification feature.
824 Disable External +V √Disables the External +V “Loss of power” notification and reverts back to
“Low Battery” notification.
825 Enable Auto Turn-Off √Callbox will automatically turn off when it has not been used (transmit or
receive) for a period of time longer than RQX Reset Time.
826 Disable Auto Turn-Off Callbox will remain on at all times. This mode of operation is not
recommended for battery-powered applications.
827 Enable Busy Channel Lockout Callbox cannot transmit when there is a received signal. A “busy signal”
will be heard on the Callbox speaker when the PTT is pressed and a
received signal is present.
828 Disable Busy Channel Lockout√Callbox will transmit whenver the PTT is pressed, regardless of any
received signal.
829 Mic Gain High Places the microphone into high gain operation where quiet and distant
voices will be heard. This mode of operation will increase background
noise transmitted by the Callbox.
820 Mic Gain Normal √Places the microphone into normal gain operation for the majority of
applications where the user is talking directly into the Callbox. This
mode of operation will decrease background noise transmitted by the
Callbox.
Receive Volume Level
875 10% Sets the speaker volume level of received signals.
876 25%
877 50% * √
878 75%
879 100% *
√The Callbox is set from the factory with these options enabled.
* Setting is also available with Single-Digit Radio Feature Code programming.

1 Series OUTPOST®Wireless Callbox Programmable Features
Have questions? Call 800-USA-1-USA (800-872-1872) or visit our website at www.ritron.com 15
P
ROGRAMMABLE
O
UTPOST
®
C
ALLBOX
F
EATURES
............................
The OUTPOST®Callbox has a variety of programmable
features that determine how your callbox operates. Some
of these features can be Field Programmed (FP) by you
without using special tools, while other features can only
be Programmed (PC) with a PC and RQX Series PC
Programmer version 10.0.2 or higher. Contact your
Ritron dealer or the factory for details.
Glossary of Terms
Intercom Mode – The Automatic Turn-Off feature has
been disabled and the Callbox is able to receive calls at
any time.
Sleep – If Automatic Turn-Off is DISABLED and Battery
Saver is ENABLED the Callbox will go into a low current
Sleep Time when it is not being used, waking up
periodically to check for a received message. Pressing
the ON/PTT button will wake-up the radio immediately.
Wake-Up – When Battery Saver is ENABLED and the
Callbox has entered the low current Sleep state, the
radio will wake-up periodically to check for a received
message. The Sleep Time is set by the Battery Saver Off
Time.
No Activity Time – A continuous period of time where
the Callbox is not sending or receiving a call.
Programmable Features Key:
FP for Field Programmable Feature– no software required
PC for PC Programmable Feature with Software
Field Programming Enable .................. (PC)
This option is ENABLED as the Factory Default setting.
This permits all Field Programmable features (FP) to be
field programmed by you. If DISABLED, the features can
only be programmed using special Ritron PC
Programming software.
Send Call Tone .......................... (PC or FP)
The Factory Default setting has the Call Tone feature ON
(refer to “How to Field Program Radio Feature Codes on
page 13). The callbox can be programmed to transmit a
Call Tone if the Reset Time has expired and the ON/PTT
button is pressed. This will alert system users that the
call is originating from the callbox.
Speaker Volume............................(PCorFP)
The Factory Default setting is medium volume. Field
programming allows you to select from 5 different
Volume settings. PC Programming allows any volume
level between 2 – 100%. A lower speaker volume
reduces audio distortion and provides a more natural
sound. For best performance, do not set the volume any
higher than is necessary for your application.
High/Low Power............................(PCorFP)
The callbox can be set to transmit at high (2-Watt) or low
(1-Watt) power. Low power is recommended in battery
powered installations.
Refer to Special Note on page 3regarding
Alkaline batteries.
Automatic Turn-Off .................... (PC or FP)
This feature is ENABLED as the Factory Default setting.
The callbox will turn OFF when the RQX Reset Time has
expired. The Reset Time is a pre-programmed amount of
time of “no activity” (no calls transmitted, no calls
received) before the callbox turns OFF in order to
conserve battery life. The callbox can be turned back ON
when the ON/PTT button is pressed. This is the
recommended mode of operation for all battery only
powered applications.
If Automatic Turn-OFF is NOT selected via the PC
programming software, the callbox does NOT completely
turn OFF, but remains in the Intercom mode, allowing the
callbox to receive calls at any time.
Operating the callbox with Automatic Turn-OFF
DISABLED significantly increases battery drain, and is
therefore NOT recommended for battery only powered
applications. Battery life can be increased using the
Battery Saver Enable feature detailed in this section.
Battery Saver Enable .......................... (PC)
When the OUTPOST®Callbox is programmed to operate
with Automatic Turn-Off disabled, Battery Saver can
increase battery life in both internal or external battery
powered applications.
With Battery Saver Enable, the callbox will periodically
Wake-Up and listen for a received signal before returning
to a low current Sleep state. The time between Wake-Up
states can be PC programmed between 0.5 - 8 seconds
with the Battery Saver Sleep Time setting. A longer time
between Wake-Up states will result in increased battery
life.
The callbox immediately leaves Battery Saver mode any
time the ON/PTT Button is pressed or a signal is
received, and will not return to Battery Saver until the
period of no activity exceeds the RQX Reset Time.
TX Time Out Time ................................ (PC)
Set from the factory for 60 seconds, the TX Time Out
Time can be programmed for 1-255 seconds. This sets
the length of time the Callbox can transmit continuously.
If the ON/PTT button is held down.
DTMF or Selcall ANI ............................ (PC)
The RQX can be programmed to send a 3-7 digit DTMF
or Selcall ANI code at the beginning of each transmission
for radio identification.
!

1 Series OUTPOST®Wireless Callbox Programmable Features
16 Have questions? Call 800-USA-1-USA (800-872-1872) or visit our website at www.ritron.com
P
ROGRAMMABLE
O
UTPOST
®
C
ALLBOX
F
EATURES
(C
ONTINUED
).............................................................................................
External +12 VDC Power Fail Alert Tone
................................................(PC or FP))
By selecting the +12 VDC Power Fail Alert Tone feature
the callbox will look for a loss of the +12 VDC power
source. The callbox will immediately transmit an Alert
Tone to notify personnel that the +12 VDC source has
been lost and is now operating on battery back-up. The
callbox will transmit an Alert Tone once every hour until
the +12 VDC power source is restored or until the back-
up batteries are exhausted. Even if this feature is NOT
selected, it will always revert to Back-up Battery power,
see page 3for details.
RQX Reset Time ........................... (PCorFP)
Set from the factory for 10 seconds, the RQX Reset Time
can be Field Programmed to 9 different times ranging
from 5 seconds to 4 minutes, and PC programmed for 1-
255 seconds. A shorter RQX Reset Time will result in
increased battery life. In standard Automatic Turn-Off
operation a longer RQX Reset Time will allow more time
for a response before the Callbox turns off.
RQX Reset Time defines the Inactivity Time allowed
before the Callbox:
•Turns Off if Automatic Turn-Off is ENABLED.
•Enters Battery Power Saver mode if Battery Power
Saver is ENABLED.
Busy Channel TX Inhibit .............(PC or FP)
If another user on the same frequency but, on a different
tone code is transmitting on your frequency, the callbox
will not be allowed to transmit. The callbox will beep a
series of long, low tones (like a busy signal) while the
ON/PTT button is held down.
Transmit Beep Enable...........................(PC)
This feature is turned on from the factory to provide a
short beep in the callbox speaker any time the ON/PTT
button is pressed. This assures the callbox user that the
radio has turned on and is ready to transmit their
message. With this feature disabled the callbox will only
beep when the radio is first turned on.
RX Courtesy Beep Enable .....................(PC)
In high noise environments it is sometimes difficult to
determine when a received message has ended. With
the RX Courtesy Beep enabled the callbox will sound a
short beep on the speaker at the end of each received
transmission.
Narrow or Wide Band Operation............(PC)
A number of table frequencies, which are Field
Programmable, offer you a choice between either narrow
(12.5 kHz) or wide (25 kHz) band operation. See
“Programmable Frequency Codes” on page 11. The
callbox automatically makes the narrow or wide band
adjustment depending on the frequency code selected.
The callbox can be PC programmed with Ritron RQX
software to operate either narrow or wide band on any
custom frequency within the specified band.
I
NTERCOM
(A
LWAYS
O
N
) P
ROGRAMMING
...................................
The OUTPOST®can be PC programmed by the factory
or by your Ritron dealer to operate as a two-way
intercom. When operating as an intercom the Automatic
Turn-Off must be DISABLED so that the radio will remain
ON in a “intercom” mode. The callbox can receive a call
from another radio at any time. The higher current
requirements of Intercom operation make it undesirable
in battery powered only installations. It is recommended
that you power the callbox using +12 VDC capability.
See page 3.
Required Radio Settings via PC Programming:
Automatic Turn-Off....................................... (PC or FP)
This feature must be DISABLED for the callbox to
remain ON at all times.
Other Programmable Features to Consider:
Battery Saver...........................................................(PC)
Battery Saver can be used to increase battery life in
battery powered applications. With Battery Saver
activated, the callbox will periodically “wake-up” and
listen for a received signal before returning to a low
current “sleep” mode. The Sleep Time can be PC
programmed between 0.5 - 8 seconds. A longer sleep
time will result in increased battery life, but may result in
missed calls.
Busy Channel TX Inhibit...............................(PC or FP)
If ENABLED this feature prevents you from talking over
someone else on the same channel even if they are
using a different tone code. The radio will beep a series
of long, low tones that sounds like a “busy signal” when
you press down the ON/PTT button.

1 Series OUTPOST™ Wireless Callbox Licensing
Have questions? Call 800-USA-1-USA (800-872-1872) or visit our website at www.ritron.com 17
FCC Licensing
Except for the five (5) MURS frequencies listed on page 11,
the FCC requires the owners of radios operating on these
frequencies to obtain a station license before using them.
The station licensee is responsible for ensuring that
transmitter power, frequency and deviation are within the
limits specified by the station license. The station licensee is
also responsible for proper operation and maintenance of
the radio equipment. This includes checking the transmitter
frequency and deviation periodically, using appropriate
methods.
To get an FCC license for VHF or UHF frequencies, submit
FCC application Form 601. Your Ritron dealer can help you
with this process.
How to Obtain an FCC Radio License
Because your Ritron radio operates on Private Land Mobile
frequencies, it is subject to the Rules and Regulations of the
FCC, which requires all operators of these frequencies to
obtain a station license before operating their equipment.
Make application for your FCC license on FCC Forms 601,
Schedules D and H, and Fee Remittance Form 159.
To have forms and instructions faxed to you by the FCC, call
the FCC Fax-On-Demand system at 202-418-0177 from
your fax machine; request Document numbers 3000159,
3060001, 3060003, and 3060006.
To have Document numbers 3000159, 3060001, 3060003,
and 3060006 mailed to you, call the FCC Forms Hotline at
800-418-FORM (800-418-3676).
For help with questions concerning the license application,
contact the FCC at 888-CALL-FCC (888-225-5322) or log
on at www.fcc.gov
You must decide which radio frequency(ies) you can
operate on before filling out your application.
For help determining your frequencies, call Ritron at
800-USA-1-USA (800-872-1872).
Safety Standards
The FCC (with its action in General Docket 79-144, March 13,
1985) has adopted a safety standard for human exposure to
radio frequency electromagnetic energy emitted by FCC
regulated equipment. Ritron observes these guidelines and
recommends that you do also:
• DO NOT hold the radio so that the antenna is very close to or
touching exposed parts of the body, especially the face or
eyes, while transmitting. Keep the radio vertical, four inches
away while talking into the front panel.
• DO NOT press the Push-To-Talk except when you intend to
transmit.
• DO NOT operate radio equipment near electrical blasting caps
or in an explosive atmosphere.
• DO NOT allow children to play with any radio equipment that
contains a transmitting device.
• Repair of Ritron products should be performed only by
Ritron authorized personnel.
INDUSTRY CANADA Regulations
Industry Canada requires the owners of the radios to
obtain a radio license before using them.
Application forms can be obtained from the nearest
Industry Canada District office.
INDUSTRY CANADA License Application
1. Fill in the items per the instructions. If you need
additional space for any item, use the reverse side
of the application.
2. Use a typewriter or print legibly.
3. Make a copy for your files.
4. Prepare a check or money order to “Receiver
General for Canada”, for the amount listed on the
following schedule for each radio purchased.
(Licenses are renewed annually on April 1st.
Refer to the following schedule for application fees
for each month.)
5. Mail the completed application, along with your
check or money order, to the closest Industry
Canada District Office.
Month of Initial Month of Initial
Application Fee Application Fee
April...........................$52 October....................$33
May...........................$50 November...............$29
June..........................$46 December...............$26
July............................$43 January....................$23
August......................$40 February..................$20
September..............$36 March.......................$16
Notes: Fees are subject to change without notice.
The annual renewal fee is $41
Service
Federal law prohibits you from making any internal
adjustments to the transmitter, and/ or from changing
transmit frequencies unless you are specifically
designated by the licensee.
If your radio equipment fails to operate properly, or
you wish to have the radio programmed, contact your
authorized dealer or Ritron.
U.S. Manufacturer:
RITRON, INC.
Repair Department
505 West Carmel Drive
Carmel, IN 46032 USA
Phone: [phone]
FAX: [phone]