RKI Instruments 35-3001A-14 User manual

www.rkiinstruments.com
35-3001A-14
Methane Sample-Draw Detector
Operator’s Manual
Part Number: 71-0603
Revision: P1
Released: 8/10/22

35-3001A-14 Methane Sample-Draw Detector
WARNING
Read and understand this instruction manual before operating
detector. Improper use of the detector could result in bodily harm
or death.
Periodic calibration and maintenance of the detector is essential
for proper operation and correct readings. Please calibrate and
maintain this detector regularly! Frequency of calibration
depends upon the type of use you have and the sensor types.
Typical calibration frequencies for most applications are between
3 and 6 months, but can be required more often or less often
based on your usage.

35-3001A-14 Methane Sample-Draw Detector
Product Warranty
RKI Instruments, Inc. warrants gas alarm equipment sold by us to be free from defects in materials,
workmanship, and performance for a period of one year from date of shipment from RKI Instruments, Inc.
Any parts found defective within that period will be repaired or replaced, at our option, free of charge. This
warranty does not apply to those items which by their nature are subject to deterioration or consumption in
normal service, and which must be cleaned, repaired, or replaced on a routine basis. Examples of such items
are:
Warranty is voided by abuse including mechanical damage, alteration, rough handling, or repair procedures
not in accordance with the operator’s manual. This warranty indicates the full extent of our liability, and we
are not responsible for removal or replacement costs, local repair costs, transportation costs, or contingent
expenses incurred without our prior approval.
THIS WARRANTY IS EXPRESSLY IN LIEU OF ANY AND ALL OTHER
WARRANTIES AND REPRESENTATIONS, EXPRESSED OR IMPLIED, AND
ALL OTHER OBLIGATIONS OR LIABILITIES ON THE PART OF RKI
INSTRUMENTS, INC. INCLUDING BUT NOT LIMITED TO, THE WARRANTY
OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. IN
NO EVENT SHALL RKI INSTRUMENTS, INC. BE LIABLE FOR INDIRECT,
INCIDENTAL, OR CONSEQUENTIAL LOSS OR DAMAGE OF ANY KIND
CONNECTED WITH THE USE OF ITS PRODUCTS OR FAILURE OF ITS
PRODUCTS TO FUNCTION OR OPERATE PROPERLY.
This warranty covers instruments and parts sold to users by authorized distributors, dealers, and
representatives as appointed by RKI Instruments, Inc.
We do not assume indemnification for any accident or damage caused by the operation of this gas monitor,
and our warranty is limited to the replacement of parts or our complete goods.
a) Absorbent cartridges d) Batteries
b) Pump diaphragms and valves e) Filter elements
c) Fuses

35-3001A-14 Methane Sample-Draw Detector
Table of Contents
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
External Components. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Internal Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Mounting the Sample-Draw Detector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Connecting the Sample Lines to the Sample-Draw Detector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Wiring the Sample-Draw Detector to a Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Start Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Introducing Incoming Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Setting the Zero Reading . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Preventive Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Replacing Components of the Sample-Draw Detector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Adjusting the Low Flow Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Removing the Particle Filter’s Tubing Stub, if Necessary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Calibration Frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Calibration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Preparing for Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Setting the Zero Reading . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Setting the Response Reading . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Returning to Normal Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

35-3001A-14 Methane Sample-Draw Detector • 1
Overview
This operator’s manual describes the 35-3001A-14 methane sample-draw detector. This manual also
describes how to install, start up, maintain, and calibrate the sample-draw detector when using it with a gas
monitoring controller. A parts list at the end of this manual lists replacement parts and accessories for the
sample-draw detector.
Specifications
Table 1 lists specifications for the methane sample-draw detector. See the controller Operator’s Manual for
information specific to the controller.
WARNING: When using the 35-3001A-14, you must follow the instructions and warnings in
this manual to assure proper and safe operation of the 35-3001A-14 and to
minimize the risk of personal injury. Be sure to maintain and periodically
calibrate the 35-3001A-14 as described in this manual.
Table 1: Specifications
Target Gases and Detection Range Methane: 0 - 100% LEL
Input Power 24 VDC Nominal (18.5 VDC - 30 VDC)
Construction (housing) Fiberglass/polyester (NEMA 4X)
Dimensions 8.5 in. H x 6.5 in. W x 4.25 in. D
Weight 4.5 lbs.
Sampling Method Sample-draw
Sample Flow 3.0 SCFH typical, with no inlet or exhaust line
Flow to Sensor 1.0 SCFH (nominal)
Low Flow Setpoint 0.6 ± 0.1 SCFH
Maximum Recommended Inlet/
Exhaust Line Length for
1/4” O.D. x 1/8” I.D. Tubing
Inlet Exhaust
50 feet 0 feet
* RKI Instruments, Inc. does not recommend installing this tubing
size on both the inlet and exhaust.
Maximum Recommended Inlet/
Exhaust Line Length for
1/4” O.D. x 0.170” I.D. Tubing
Inlet Exhaust
50 feet 50 feet
75 feet 0 feet
Response Time 90% in 30 seconds
Accuracy ± 5% of reading or ± 2% of full scale (whichever is greater)

2 • 35-3001A-14 Methane Sample-Draw Detector
Description
This section describes the components of the methane sample-draw detector.
Figure 1: Methane Sample-Draw Detector Component Location
_Pump
Oxygen
Sensor
Terminal
Strip
Mounting
Foot, 4X
W
+
B
O
X
Y
G
E
N
S
PWR/SIG
Sensor
Current
14 8mA
Detector/Amp
Terminal Strip
(Factory
Wired)
GW B
W
LEL
GBR
R
+
OXY
S
AMP 2AMP
+
+S
Pilot LED
Fail LED
Sensor Flow
Control Valve
Pump Reset
Switch
Pressure
Switch
Adjustment
Screw
(behind PCB)
Flowmeter
BGW
Interconnect
Terminal
Strip
AMP 2
S
+S
AMP 1
+ R
+
WG
OXY
PWR/SIG
Particle
Filter
LEL /IR
Flowmeter Circuit
Board Connector
LEL /IR
Inlet
Fitting
Exhaust
Fitting
This End
To Inlet
Fitting 3/4" Conduit Hub
INLET
EXHAUST
IR Amplifier, x2
Pump Connector
Hydrophobic
Filter
IR CH4
Flow Block,x2
IR CH4 Sensor
(inside block), x2
IR CH4 Sensor
PCB, x2

35-3001A-14 Methane Sample-Draw Detector • 3
External Components
This section describes the sample-draw detector’s external components.
Housing
The sample-draw detector’s fiberglass housing is weather- and corrosion-resistant. It is suitable for
installation where general purpose equipment is in use.
The housing door is hinged on the left side and is secured by two latches on the right side. The flowmeter
and status LEDs are visible through a window in the housing door.
Four mounting feet are attached to the back of the housing (one at each corner). Use the mounting feet to
install the housing to a vertical surface.
Sample Fittings
The sample fittings are located on the left side of the bottom of the housing. The inlet fitting is near the front
of the housing and the exhaust fitting is near the back of the housing. The sample fittings accept 1/4 in. rigid
tubing. See the Installation section on page 7 to connect tubing to the sample fittings.
Particle Filter
A particle filter with a tubing stub on one end is shipped with the instrument but it is not factory installed. If
the particle filter is installed directly to the inlet fitting, the tubing stub must be used. If the particle filter is
installed somewhere else, like at the end of the inlet line, the tubing stub can be used or removed.
Conduit Hub
One 3/4” conduit hub is located on the right side of the bottom of the housing. It is used for routing wiring
into the housing by using conduit or an appropriate cable bushing.
Internal Components
This section describes the sample-draw detector’s internal components (see Figure 1). Figure 2 illustrates
how the gas sample moves through the flow system.
Figure 2: Methane Sample-Draw Detector Flow Diagram
Flowmeter
IR CH4
Sensor
Pump
IR CH4
Sensor
Restrictor
Particle Filter
Flowmeter PCB
Exhaust
Sensor Flow
Control Valve
Hydrophobic Filter
Pressure Switch
Inlet

4 • 35-3001A-14 Methane Sample-Draw Detector
Main Circuit Board
The main circuit board includes the detector/amp terminal strip, interconnect terminal strip, oxygen sensor
terminal strip, pump connector, and flowmeter circuit board connector (see Figure 1).
Detector/Amp Terminal Strip
The detector/amp terminal strip is the upper twelve-point terminal strip in the bottom right corner of the
main circuit board. Use the detector/amp terminal strip to connect the IR CH4amplifiers to the main circuit
board.
NOTE: The IR CH4amplifiers are factory-wired to the main circuit board. See the “Installation”
section on page 7 for all wiring procedures related to the sample-draw detector.
Interconnect Terminal Strip
The interconnect terminal strip is the lower twelve-point terminal strip in the bottom right corner of the main
circuit board. Use the interconnect terminal strip to connect the sample-draw detector to a controller.
Oxygen Sensor Terminal Strip
The oxygen sensor terminal strip is a two-point terminal strip in the upper right corner of the main circuit
board. This terminal strip is not used in this version of the sample-draw detector.
Pump Connector
The pump connector is the two-point connector below the oxygen terminal strip in the upper right corner of
the main circuit board. Use the pump connector to connect the pump to the main circuit board.
NOTE: The pump is factory-wired to the main circuit board. See “Installation” on page 7 for all
wiring procedures related to the sample-draw detector.
Flowmeter Circuit Board Connector
The flowmeter circuit board connector is a six-position connector in the upper left corner of the main circuit
board. Use the flowmeter circuit board connector to connect the flowmeter circuit board to the main circuit
board.
NOTE: The flowmeter circuit board is factory wired to the main circuit board. See “Installation”
on page 7 for all wiring procedures related to the sample-draw detector.
Flowmeter Circuit Board
The flowmeter circuit board is mounted to the left side of the main circuit board using standoffs. It includes
the flowmeter, sensor flow control valve, status LEDs, pressure switch, and pump reset switch.
Flowmeter
The flowmeter is mounted to the right side of the flowmeter circuit board. You can see it through the
window in the door. A ball in the flowmeter column indicates the flow rate to the sensor. The flowmeter
measures the flow in the range 0.2 to 2.0 SCFH (Standard Cubic Feet per Hour). The optimum flow rate is
1.0 SCFH.
Sensor Flow Control Valve
The sensor flow control valve is mounted to the flowmeter circuit board above the flowmeter. The sensor
flow control valve adjusts the flow rate to the detector. Turn the valve’s knob clockwise to increase the flow
and counterclockwise to decrease the flow.

35-3001A-14 Methane Sample-Draw Detector • 5
Status LEDs
Two status LEDs are above the flowmeter. They are also visible through the window in the housing door.
The green Pilot LED is on when the sample-draw detector is receiving power from the controller. The red
Fail LED is on when the sample flow rate is below the low flow level.
Pressure Switch
The pressure switch is mounted to the back of the flowmeter circuit board. The pressure switch monitors the
flow rate of the incoming gas sample.
If the flow rate falls below the preset low flow level, the pressure switch causes the Fail LED to turn on and
interrupts the signal from the detector. The interrupted detector signal causes a fail condition at the
controller. The low flow level is factory-set at 0.6 SCFH (±0.1 SCFH). See “Adjusting the Low Flow
Setting” on page 16 to adjust this setting.
Pump Reset Switch
The pump reset switch is located to the left of the status LEDs. When a low flow condition occurs, the pump
will be shut off. To reset the low flow condition and start the pump again, press and hold the pump reset
switch for about 2 seconds, then release.
Hydrophobic Filter
The hydrophobic filter is located toward the bottom left of the main circuit board. The filter prevents
particulates and water in the incoming gas sample from damaging the flow and detection systems. Replace
the filter when it appears dirty, discolored, or clogged.
Pump
The pump is mounted to the right side of the main circuit board. The pump pulls the gas sample into the
sample-draw detector. The pump operates on 24 VAC, which is generated from the 24 VDC supplied by the
controller.
IR CH4Sensor/IR CH4Sensor PCB
Each methane sensor is an infrared type plug-in detector. They are each installed in an IR CH4flow block
and the IR CH4flow blocks are mounted to the middle of the main circuit board. A small circuit board, the
IR CH4sensor PCB, with a 4-wire cable mates to the IR CH4sensor and retains each sensor in the flow
block. The cable is wired to an IR CH4amplifier. The IR CH4sensor PCB allows you to replace the sensor
without disconnecting the wiring.

6 • 35-3001A-14 Methane Sample-Draw Detector
IR CH4Amplifier
Each IR CH4amplifier converts the electrical output from the IR CH4 sensor to a 4 to 20 mA signal that
corresponds to the detection range and transmits the signal to a gas monitoring controller. A label on the
amplifier indicates the detector drive current. This drive current is factory set. One amplifier is mounted on
the top middle edge of the main circuit board. The other is mounted in the bottom left corner of the main
circuit board. Each amplifier consists of the zero pot, span pot, controller terminal strip, detector terminal
strip, and test points.
Figure 3: IR CH4Amplifier Component Location
Zero Pot
The zero pot is located in the upper right corner of the amplifier (see Figure 3). Use a small flat blade
screwdriver to turn the zero pot’s adjustment screw and adjust the amplifier’s zero (fresh air) output during
the start-up and calibration procedures. Turn the adjustment screw clockwise to increase the fresh air output
and counterclockwise to decrease the fresh air output.
Span Pot
The span pot is located below the zero pot (see Figure 3). Use a small flat blade screwdriver to turn the span
pot’s adjustment screw and adjust the amplifier’s gas response output during the calibration procedure. Turn
the adjustment screw clockwise to increase the span output and counterclockwise to decrease the span
output.
CAUTION: The amplifier includes additional pots. They are factory-set. Do not adjust them.
Controller and Detector Terminal Strips
The controller terminal strip and detector terminal strip are three- and four-position plug-in style terminal
strips, respectively. The controller terminal strip is located on the right side of the amplifier and the detector
terminal strip is to the left of it. Both terminal strips are factory wired to the sensor and main circuit board.
Test Points
The test points are on the left side of the amplifier (see Figure 3). The test points produce a 100 mV to 500
mV output that corresponds to the sample-draw detector’s 4 to 20 mA output. Use the test points and a
voltmeter to measure the amplifier’s output during the start-up and calibration procedures. The black test
point in the upper left corner is the negative (-) test point and the red test point to the left of the zero and span
pots is the positive (+) test point.
Factory Set Pots
Sensor
Current
148mA
WLELGBR
Test Points
100-500 mV Range Zero Pot
Detector
Terminal Strip
Span Pot
Controller
Terminal Strip
S
PWR / SIG

35-3001A-14 Methane Sample-Draw Detector • 7
Installation
This section describes procedures to mount the sample-draw detector in the monitoring environment and
wire the sample-draw detector to a controller.
Mounting the Sample-Draw Detector
1. Select the mounting site. Consider the following when you select the mounting site:
• Is there enough room to open the housing door and make wiring and tubing connections at the
bottom of the housing?
• Make sure there is sufficient room to perform start-up, maintenance, and calibration
procedures.
• Are the flowmeter and status LEDs visible?
Figure 4: Outline and Mounting Dimensions
Ø.30x.50(4X)MOUNTING
.78
1.13
.40
Pilot Fail
.85
.80
4.50
NOTE: Housing is4.3 inchesdeep
8.88
4.00
6.50
35-3001
www.rkiinstruments.com
Sample Drawing
Gas Detector
8.50

8 • 35-3001A-14 Methane Sample-Draw Detector
2. Close and latch the housing door.
NOTE: The sample-draw detector is shipped with the mounting feet “tucked under” the housing
to protect the mounting feet during shipment.
3. Slightly loosen the screw that secures the mounting foot to the housing, then rotate the mounting foot
180 degrees (see Figure 4).
4. Tighten the screw that secures the mounting foot to the housing.
5. Repeat steps 3 and 4 for the remaining three mounting feet.
6. Position the sample-draw housing on a vertical surface at eye level (4 1/2 to 5 feet from the floor).
7. Insert 1/4 inch screws through the slots in the mounting feet to secure the housing to the mounting
surface.
Connecting the Sample Lines to the Sample-Draw Detector
See Figure 6 for the fitting layout.
Installing the Inlet Line with Particle Filter Connected to the Inlet Fitting
1. Loosen the nut on the inlet fitting until 3 threads are visible.
2. Push the particle filter’s tubing stub into the inlet fitting until it stops. Be sure the arrow on the
particle filter is pointing toward the inlet fitting.
3. Hand tighten the nut on the inlet fitting so the ferrules clamp on the tubing. If the tube nut is removed,
see Figure 6 for the arrangement of the fitting components.
4. Connect a length of sample tubing to the other side of the particle filter and route it to the sampling
area. 1/4” O.D. rigid polypropylene, Teflon, or flexible polyurethane tubing may be used. RKI
Instruments, Inc. recommends using either 1/4” O.D. x 1/8” I.D. or 1/4” O.D. x 0.170” I.D. tubing
based on your length requirements. See “Specifications” on page 1 for maximum tubing lengths
based on tubing size.
CAUTION: If you use flexible sample tubing (polyurethane is acceptable), use an appropriate
insert if necessary to provide support to the tubing and ensure a good seal when
connecting to the flexible stub on the filter.
CAUTION: Avoid loops or slumps in the incoming sample line. To reduce response time, keep the
incoming sample line as short as possible.
Installing the Inlet Line without Particle Filter Connected to the Inlet Fitting
1. Loosen the nut on the inlet fitting until 3 threads are visible.
2. Push 1/4” O.D. rigid polypropylene or rigid Teflon sample tubing into the fitting until it stops.
Flexible polyurethane tubing may be used with an appropriate insert. RKI Instruments, Inc.
recommends using either 1/4” O.D. x 1/8” I.D. or 1/4” O.D. x 0.170” I.D. tubing based on your
length requirements. See “Specifications” on page 1 for maximum tubing lengths based on tubing
size.
CAUTION: If you use flexible sample tubing (polyurethane is acceptable), use an appropriate
insert to seal the connection between the tubing and the inlet fitting.

35-3001A-14 Methane Sample-Draw Detector • 9
3. Hand tighten the nut on the inlet fitting so the ferrules clamp on the tubing. If the tube nut is removed,
see Figure 6 for the arrangement of the fitting components.
4. Route tubing from the inlet fitting to the sample area. See “Specifications” on page 1 for maximum
tubing lengths based on tubing size.
CAUTION: Avoid loops or slumps in the incoming sample line. To reduce response time, keep the
incoming sample line as short as possible.
5. If desired, install the particle filter onto the end of the inlet line. Be sure the arrow on the particle
filter is pointed toward the inlet line.
Installing the Exhaust Line
1. Loosen the nut on the exhaust fitting until 3 threads are visible.
2. Push 1/4” O.D. rigid polypropylene or rigid Teflon sample tubing into the fitting until it stops.
Flexible polyurethane tubing may be used with an appropriate insert. RKI Instruments, Inc.
recommends using either 1/4” O.D. x 1/8” I.D. or 1/4” O.D. x 0.170” I.D. tubing based on your
length requirements. See “Specifications” on page 1 for maximum tubing lengths based on tubing
size.
CAUTION: If you use flexible sample tubing (polyurethane is acceptable), use an appropriate
insert to seal the connection between the tubing and the inlet fitting.
3. Hand tighten the nut on the exhaust fitting so the ferrules clamp on the tubing. If the tube nut is
removed, see Figure 6 for the arrangement of the fitting components.
4. Route the opposite end of the tubing to an open area where the sample can safely disperse or to an
exhaust duct. See “Specifications” on page 1 for maximum tubing lengths based on tubing size.
Wiring the Sample-Draw Detector to a Controller
WARNING: Always verify that the controller is off and that power to the controller is
off before you make wiring connections.
1. Turn off the controller.
2. Turn off power to the controller.
3. Unlatch and open the housing door of the sample-draw detector.
4. Guide a five-conductor, shielded cable or five wires in conduit through the conduit hub at the bottom
of the sample-draw housing. A minimum of 18 AWG wire is recommended.
5. Connect the cable to the sample-draw detector’s interconnect terminal strip as shown in Figure 5.
6. Close and latch the housing door of the sample-draw detector.
CAUTION: If using shielded cable, leave the cable shield’s drain wire insulated and
disconnected at the sample-draw detector. You will connect the opposite end of the
drain wire at the controller.
7. Route the cable or wires in conduit leading from the sample-draw detector through one of the conduit
hubs at the controller.

10 • 35-3001A-14 Methane Sample-Draw Detector
8. Connect the wires to the applicable detector/transmitter terminal strip at the controller as shown in
Figure 5. Refer to the controller operator’s manual and the controller detector head specification
sheet for the 35-3001A-14 for detector/terminal strip connections specific to the controller.
Figure 5: Wiring the Sample-Draw Detector to a Controller
9. If shielded cable is used, connect the cable’s drain wire to an available chassis (earth) ground at the
controller. RKI controllers typically have a ground stud that can be used to ground the cable’s drain
wire.
White
Not Used on
This Version
Black
Red
ZERO
SPAN
S
PWR/SIG
White
Red
Green
Black
Red
LEL/IR
LEL/IR
AMP2AMP1
AMP1 AMP2
PATS201PATS201
White
PATS101PATS101
OXY
IR CH4
Sensor PCB
IR CH4
Sensor OXY
Sensor
Current
148 mA
IR CH4
Sensor PCB
SPAN
Black
W
LEL
GBR
ZERO
S
PWR/SIG
W
LEL
GBR
Sensor
Current
148 mA
Red
Black
Green
4/20 Signal
+ 24 VDC
White
4/20 Signal
+ 24 VDC
IR CH4
Sensor
Controller or Recording Device
- (DC Ground)
- (DC Ground)
CH4 2
CH4 1

35-3001A-14 Methane Sample-Draw Detector • 11
Start Up
This section describes procedures to start up the sample-draw detector and place the sample-draw detector
into normal operation.
Introducing Incoming Power
1. Complete the installation procedures described earlier in this manual.
2. Verify that the wiring is correct and secure. Refer to the controller operator’s manual for connections
at the controller.
3. Turn on or plug in the power to the controller, then turn on the controller.
4. Verify that the sample-draw detector’s Pilot LED is on.
5. Verify that the controller is on and operating properly. Refer to the controller operator’s manual.
NOTE: When first powered up, the sample-draw detector will enter about a one minute period
when the 4-20 mA output is stabilizing and may be above the controller alarm points or
well below zero momentarily. RKI controllers have a one minute warmup period when
the controller does not display any gas reading or give any alarm indication. The
transmitter’s 4-20 mA signal should be stable by the time the controller’s warmup period
is over.
6. Verify that the flowmeter indicates a flow rate of approximately 1.0 SCFH. If necessary, use the
sensor flow control valve to adjust the flow rate. Turn the valve’s knob clockwise to increase the flow
and counterclockwise to decrease the flow.
NOTE: The following step tests for leaks in the sample line. This test will cause a low flow
condition at the sample-draw detector and a fail condition at the controller. Be sure to put
the controller into its calibration program or disable external alarms before performing
this test.
7. Verify that the incoming sample line is not leaking. To test the sample line, press and hold the reset
switch and plug the open end of the sample line with your thumb. If the flowmeter ball drops to the
bottom of the flowmeter, the incoming sample line is not leaking.
8. Remove your thumb from the sample line, release the reset switch, and verify the flowmeter returns
to a normal flow rate.
9. Enable alarms or place the controller in normal operation.
CAUTION: Allow the sample-draw detector to warm up for 5 minutes before you continue with
the next section, “Setting the Zero Reading.”

12 • 35-3001A-14 Methane Sample-Draw Detector
Setting the Zero Reading
CAUTION: If you suspect the presence of combustible or toxic gas or an abnormal oxygen
concentration in the monitoring environment, use the calibration kit and the zero air
calibration cylinder to introduce “fresh air” to the sensor and verify an accurate
zero setting. See “Calibration” on page 18 for instructions on using a zero air
calibration cylinder for setting the zero reading.
1. Verify that the sample-draw detector is sampling a fresh air environment (environment known to be
free of combustible and toxic gas and of normal oxygen concentration, 20.9%).
2. Verify a reading of 0% LEL on the controller display screen for the applicable channel.
If the display reading is 0% LEL both channels, start up is complete. The sample-draw detector is in
normal operation. If the display reading is not 0% LEL for both channels, continue with step 3.
3. Perform a zero (fresh air) operation at the controller. See “Calibration” on page 18 for instructions to
perform a zero (fresh air) operation.
Maintenance
This section describes maintenance procedures. It includes preventive maintenance procedures. This section
also includes procedures to troubleshoot the sample-draw detector, replace components of the sample-draw
detector, adjust the low flow setting, and remove the particle filter’s tubing stub.
Preventive Maintenance
This section describes a preventive maintenance schedule to ensure the optimum performance of the sample-
draw detector. It includes daily and biannual procedures.
Daily Visual Checks
1. Verify that the Pilot LED is on.
2. Verify that the flowmeter indicates a flow rate of approximately 1.0 SCFH. If necessary use the
sensor flow control valve to adjust the flow rate to 1.0 SCFH. Turn the valve’s knob clockwise to
increase the flow and counterclockwise to decrease the flow.
3. Verify a display reading of 0% LEL for both channels. Investigate significant changes in the display
reading.
Biannual Calibration
Calibrate the sample-draw detector as described in “Calibration” on page 18.
Troubleshooting
The troubleshooting guide describes symptoms, probable causes, and recommended action for problems you
may encounter with the sample-draw detector.
NOTE: This troubleshooting guide describes sample-draw detector problems only. See the
controller Operator’s Manual if the controller exhibits any problems.
Fail Condition
Symptoms
• The sample-draw detector’s Fail LED is on.
• The monitoring device is operating properly but indicates a reading well below zero.

35-3001A-14 Methane Sample-Draw Detector • 13
Probable causes
• The sample-draw detector’s flow rate is too low because of an obstructed sample line, failed
pump, etc.
• The sample-draw detector is malfunctioning.
• The sensor wiring is disconnected or misconnected.
Recommended action
1. At the sample-draw detector, set the correct flow rate with the sensor flow control valve.
2. If you cannot set the correct flow rate, check the sample lines for obstructions or kinks.
3. Verify that the sensor wiring is correct and secure. “Wiring the Sample-Draw Detector to a
Controller” on page 9 describes sensor wiring connections.
4. Calibrate the sample-draw detector as described in “Calibration” on page 18 and “Parts List” on
page 20.
5. If the fail condition continues, replace the sensor(s) as described in “Replacing Components of the
Sample-Draw Detector” on page 13.
6. If the fail condition continues, contact RKI Instruments, Inc. for further instruction.
Slow or No Response/Difficult or Unable to Calibrate
Symptoms
• Unable to accurately set the zero or response reading during the calibration procedure.
• The sensor requires frequent calibration.
Probable causes
• The calibration cylinder is low, out-dated, or defective.
• If a demand flow regulator calibration kit is used, the demand flow regulator is not functioning
properly.
• The sample-draw detector’s flow rate is too low because of an obstructed sample line, failed
pump, etc.
• The sample-draw detector is malfunctioning.
Recommended action
1. Verify that the calibration cylinder contains an adequate supply of a fresh test sample.
2. If a demand flow regulator calibration kit is used, use a different demand flow regulator to determine
if the original one is functioning properly.
3. If necessary, set the correct flow rate with the sensor flow control valve.
4. If you cannot set the correct flow rate, check the sample line for obstructions or kinks.
5. If the calibration/response difficulties continue, replace the sensor as described later in this section.
6. If the calibration/response difficulties continue, contact RKI Instruments, Inc. for further instruction.
Replacing Components of the Sample-Draw Detector
This section includes procedures to replace the IR CH4sensor, IR CH4amplifier, hydrophobic filter, and
particle filter.
Replacing the IR CH4Sensor
1. Turn off the controller.
2. Turn off power to the controller.

14 • 35-3001A-14 Methane Sample-Draw Detector
3. Open the housing door of the sample-draw detector.
4. Unscrew and remove the four screws that secure the IR CH4sensor PCB, then lift the IR CH4sensor
PCB and sensor off of the flow block.
There is a gasket at the bottom of the flow block. Be sure the gasket stays in place.
5. Unplug the sensor from the IR CH4sensor PCB.
6. Verify that you are using the correct replacement sensor, then plug the sensor into the IR CH4sensor
PCB.
7. Place the sensor and sensor PCB in the IR CH4sensor cavity.
8. Secure the sensor PCB on the flow block with the four screws you removed in step 4.
9. Close and latch the housing door.
10.Turn on power to the controller.
11.Turn on the controller.
CAUTION: Allow the replacement sensor to warm up for 5 minutes before you continue.
12.Calibrate the replacement sensor as described in “Calibration” on page 18.
Replacing the IR CH4Amplifier
1. Turn off the controller.
2. Turn off power to the controller.
3. Open the housing door of the sample-draw detector.
4. Remove the detector and controller plug-in terminal strips by grasping the sides of the strips with
your fingers. Let the terminal strips hang by their connected wires while you replace the amplifier.
5. Unscrew the screw in the lower left corner of the amplifier and remove the screw, lock washer, and
flat washer. Be careful not to lose any of these parts.
6. Remove the old amplifier from the main circuit board.
7. Install the new amplifier in the same orientation as the old amplifier. See Figure 1.
8. Reinstall the screw, lock washer, and flat washer you removed in step 5.
9. Install the detector and controller plug-in terminals strips into their sockets on the new amplifier. If
controller leads or detector cable leads were removed from the plug-in terminal strips during this
procedure, refer to Table 2 and Table 3 below.
Table 2:Reconnecting the Amplifier
to the Detector/Amp Terminal Strip
Amplifier Controller
Terminal Strip
Detector/Amp Terminal
Strip on Main PCB
PWR/SIG “-” -
PWR/SIG “S” S
PWR/SIG “+” +

35-3001A-14 Methane Sample-Draw Detector • 15
NOTE: When the sample-draw detector is first powered up with a new amplifier, the initial
output may be either high or below zero depending on the setting of the zero pot. Be sure
to make arrangements so that this does not cause unwanted alarms.
10.Turn on power to the controller.
11.Turn on the controller and place it into normal operation.
12.Allow the sample-draw detector to warmup for 5 minutes.
13.Calibrate the IR CH4sensor as described in “Calibration” on page 18.
Replacing the Hydrophobic Filter
1. Turn off the controller.
2. Turn off power to the controller.
3. Open the housing door of the sample-draw detector.
4. Disconnect the filter from the rubber elbows on each end of the filter, then remove the filter from the
sample-draw detector.
5. Install the new filter. Be sure the side of the filter marked “INLET” is connected to the elbow that is
connected to the inlet fitting.
6. Turn on power to the controller.
7. Turn on the controller.
8. Verify that the flow rate is approximately 1.0 SCFH, then close the housing door.
Replacing the Particle Filter
1. Turn off the controller.
2. Turn off power to the controller.
3. If the particle filter is installed at the inlet fitting:
1. Disconnect the tubing routed to the sampling area, if installed, from the particle filter.
2. Disconnect the particle filter from the tubing stub.
3. Install the new particle filter onto the tubing stub. Be sure the arrow on the particle filter is
pointing toward the inlet fitting.
4. Reinstall the tubing routed to the sampling area.
Table 3:Reconnecting the IR Methane Sensor to the Amplifier
Amplifier Detector
Terminal Strip Detector Lead
DETECTOR “R” RED
DETECTOR “W” WHT
DETECTOR “G” GREEN
DETECTOR “B” BLK

16 • 35-3001A-14 Methane Sample-Draw Detector
5. If the particle filter is installed at the end of the inlet line:
1. Remove the particle filter from the tubing stub.
2. Install the new particle filter onto the tubing stub. Be sure the arrow on the particle filter is
pointing toward the inlet line.
3. Turn on power to the controller.
4. Turn on the controller.
Adjusting the Low Flow Setting
NOTE: Adjusting the low flow setting will cause a low flow alarm at the sample-draw detector
and a fail alarm at the controller. Be sure to put the controller into its calibration program
or disable external alarms before performing this test.
The factory-set low flow setting is 0.6 SCFH (±0.1). To adjust the low flow setting:
1. Use the sensor flow control valve to set the flow to 0.6 SCFH. Turn the valve’s knob clockwise to
increase the flow and counterclockwise to decrease the flow.
If the sample-draw detector goes into low flow alarm before you can adjust the flow down to 0.6
SCFH, adjust the pressure switch adjustment screw 1/4 turn clockwise, then attempt to set the flow
again. Repeat this step until you are able to adjust the flow to 0.6 SCFH.
NOTE: The pressure switch adjustment screw is accessible through a circular cutout in the
flowmeter circuit board.
2. Slowly turn the pressure switch adjustment screw counterclockwise just until the sample-draw
detector goes into low flow alarm.
3. Turn the sensor flow control valve’s knob clockwise to increase the flow until the unit is out of low
flow alarm when the reset switch is pressed and released.
4. Decrease the flow very slowly by turning the sensor flow control valve’s knob counterclockwise and
verify that the low flow alarm is 0.6 SCFH (±0.1).
If the low flow alarm is set too high, turn the pressure switch adjustment screw slightly clockwise.
Repeat steps 3 and 4 if necessary.
5. Use the sensor flow control valve to set the flow to 1.0 SCFH.
6. Make sure the sample-draw detector’s Fail LED is off.