Lumascape Centria C1 User manual

INSTALLATION INSTRUCTIONS
STAKE MOUNT / CONCRETE ANCHOR
ADJUSTABLE SPOTLIGHT
LUMASCAPE ASIA PACIFIC Brisbane Technology Park, 18 Brandl Street, Eight Mile Plains, QLD 4113, Australia
Phone [phone] | Fax [phone] | Email: [email protected] | www.lumacape.com
LUMASCAPE NORTH AMERICA 1300 Industrial Road, Unit #19, San Carlos, CA 94070, USA
Phone [phone] | Fax [phone] | Email: [email protected] | www.lumacape.com
Products and specifications are subject to change without notice.
USA I Australia I Asia I Middle East I Europe
1 / 3
IN0181US N181205
Centria C1 LS2010
READ ALL SAFETY INSTRUCTIONS FIRST
› Follow instructions carefully, failure to do so will void
warranty.
› Ensure installation complies with local law and
applicable standards.
› Input voltage is 120-277 V AC, 50/60 Hz
› Only use Lumascape power supply, control equipment
and leader cables.
› Ensure mains input power is surge protected.
› Never make connections whilst the power is connected.
› Do not make modifications or alter the product.
› Keep luminaire and connections clean and free of debris
and moisture.
› It is the installers responsibility that the installation is
adequately sealed to avoid moisture ingress.
LS2010
LS6054
Stake Mount
Concrete Anchor
Order Separately
WARNING
Install in accordance with
National Electric Code, ANSI/NFPA 70 or
the Canadian Electrical Code,
Part I (CEC), CSA C22.1

INSTALLATION INSTRUCTIONS
STAKE MOUNT / CONCRETE ANCHOR
ADJUSTABLE SPOTLIGHT
LUMASCAPE ASIA PACIFIC Brisbane Technology Park, 18 Brandl Street, Eight Mile Plains, QLD 4113, Australia
Phone [phone] | Fax [phone] | Email: [email protected] | www.lumacape.com
LUMASCAPE NORTH AMERICA 1300 Industrial Road, Unit #19, San Carlos, CA 94070, USA
Phone [phone] | Fax [phone] | Email: [email protected] | www.lumacape.com
Products and specifications are subject to change without notice.
USA I Australia I Asia I Middle East I Europe
2 / 3
IN0181US N181205
Centria C1 LS2010
North American Market - Assemble Concrete Anchor / Spike
Step 1
Step 2
If required, assemble the anchoring fins. These can be a attached to the Mounting Spike / Concrete Anchor to
increase the stability and to eliminate any rotational movement in the finished installation.
Slide in the Mounting Spike / Concrete Anchor between the assembled Anchoring Fins. Secure the fins to the
anchor using screws. It is not time to attach the luminaire to the Spike / Anchor.
Luminaire can be inserted into
concrete / dry soil to this line.

INSTALLATION INSTRUCTIONS
STAKE MOUNT / CONCRETE ANCHOR
ADJUSTABLE SPOTLIGHT
LUMASCAPE ASIA PACIFIC Brisbane Technology Park, 18 Brandl Street, Eight Mile Plains, QLD 4113, Australia
Phone [phone] | Fax [phone] | Email: [email protected] | www.lumacape.com
LUMASCAPE NORTH AMERICA 1300 Industrial Road, Unit #19, San Carlos, CA 94070, USA
Phone [phone] | Fax [phone] | Email: [email protected] | www.lumacape.com
Products and specifications are subject to change without notice.
USA I Australia I Asia I Middle East I Europe
3 / 3
IN0181US N181205
Centria C1 LS2010
Colour Designation
Black Active
White Neutral
Green Earth
Red Data
North American Market
Luminaire Tilt
Loosen to adjust luminaire tilt.
Tighten to lock tilt into place.
Luminaire Rotation
Loosen to adjust luminaire rotation.
Tighten to lock rotation into place.
Mounting Spike / Concrete Anchor
Place in soil or concrete. It is the installers
responsibility to ensure that the installation
complies with local wiring rules.
Connection Wires
Connect to supply wires.
Refer to table for conductor
colour and designation.
Attach luminaire to
Mounting Spike / Concrete Anchor.
Power supply must be isolated prior to connection
or disconnection of cables. Failure to do so will
result in damage to the luminaire components.