John Lewis ercol Shalstone 80311511 User manual

Thank you for purchasing this Shalstone 2 Door Wardrobe. Please read the instructions carefully before use
to ensure safe and satisfactory operation of this product
WARNING. In order to prevent overturning this product must be used with the wall attachment device
provided
The fıttings pack contains
SMALL ITEMS
which should be
KEPT AWAY FROM YOUNG
CHILDREN.
This product is HEAVY, it should be assembled as near as possible to the point of use.TAKE CARE
WHEN LIFTING to avoid personal injury and (or) damage to the product.
Please check the pack contents before attempting to assemle this product. A full checklist of components is
given in this leaflet. If any components are missing, please contact the retailer from whom you bought this
product.
Pre-assembly preparation
Please ensure instructions are read in full before attempting to assemble this product.
This item is HEAVY
Shalstone 2 Door Wardrobe
Stock numbers 80311511
Necessary Tools
This product is product takes approximately 1 HOUR TO assemble with 2 PEOPLE.
for John Lewis
Page 1of 12

Screw 4mm x 35mm x 1 pc
Allen Key M.4 x 1 pc
Wooden Rail Support x 1 pc
1
Top Panel x 1
2
Base Panel x 1
3
Back Panel x 1
4
L/H Side Panel x 1
5
R/H Side Panel x 1
6
Drawer x 1
A
Cam Heads x 10 pcs
B
Cam Rods x 10 pcs
C
Wooden Dowels x 16 pcs
D
Hinge x 2 pcs
E
Soft Closing Hinge x 4 pcs
F
Screw 3,5mm x 50mm x 5 pcs
G
Screw 3,5mm x 16mm x 14 pcs
H
Screw 3,5mm x 25mm x 6 pcs
9
L/H Door x 1
I
7
Hanging Rail x 1
8
Bottom Rail x 1
Allen Head Screw (4 x 50mm) x 6 pcs
10
R/H Door x 1
J
11
Back Panel x 2
K
N
Textile Strap x 2 pcs
M
Wedges x 2 pcs
12
Vertical Back Rail x 1
L
1
Fittings and parts checklist
2
3
4
5
6
7
8
9
10
11
12
Page 2 of 12

Step 2
Attach the base panel ( 2 ) to the back panel ( 3 ) with 3x screws ( F) by using screwdriver as shown.
Step 1
RH x LH panels to be assembled before moving to step 2. Screw 5x cam rods ( B ) into the holes. Insert the
2x wooden dowels ( C ) in to the holes on the side panel by using a soft hammer as shown. Repeat same step for the
other panel.
4-5
C
2
3
2
3
F
F
F
B
B
B
B
B
C
Page 3 of 12

Step 3
Put 8x cam heads ( A ) into the holes as shown. Insert the 4x wooden dowels ( C ) into the holes
by using a soft hammer as shown.
Step 4
Attach the wooden rail support (L) to the top panel ( 1 ) by using 1x screw ( F ) as shown. Note that
the screw must be screwed from the top surface of the panel where there is a countersink on the hole .
A
2
Step 5
Put 2x cam heads ( A ) to the bottom rail ( 8 ) as shown. Insert the 2x wooden dowels ( C ) into
the holes by using a soft hammer as shown.
3
C
C
A
A
A
A
A
1
L
F
A
A
C
C
Page 4 of 12

3
Step 6
With the aid of an assistant, locate the atached base and back panel ( 2 ) ( 3 ) and bottom rail ( 8 )
on to the LH side panel ( 4 ) using cams and dowels provided. Tighten the 5x cam heads ( 1 ).
2
4
8
Step 7
With the aid of an assistant, locate the R/H side panel ( 5 ), on to the carcass using cams and
dowels provided. Tighten the 5x cam heads ( 1 ).
4
3
2
8
5
Page 5 of 12

7
1
Step 8
Slide the wooden hanging rail ( 7 ) through the hole of wooden rail support ( K ) on the top panel ( 1
) as shown.
Step 9
Attach top panel ( 1 ) to the carcass as shown. Tighten 6x Allen head screws ( I ) by using Allen
key provided ( K ).
I
I
K
Page 6 of 12

11
Step 10
Put into place the back panel ( 11 ). Attach the vertical back rail ( 12 ).
Join 2x back panels ( 11 ) with vertical back rail ( 12 ) locate in recess at rear of cabinet as shown. Note that it
would be better to put a styrofoam or a cardboard piece under the robe to protect its front surface from sharp
objects.
11
12
Page 7 of 12

Step 11
With uneven floors you may need to align the wardrobe. Please check the alignment of the
wardrobe before screwing the back panels and vertical rail. Screw the back panels by using 6x screws ( H ),
screw vertical back rail by using 1x screw ( J ) from the back and 1x screw ( F ) from the top panel as shown.
A
B
A-A = B-B
MEASURE & ALIGN
J
H
A
B
F
H
J
F
H
Page 8 of 12

Step 12
Lay the doors onto a smooth flat surface so the holes are facing upwards. Screw 4x soft closing hinges
(E) to top and bottom, 2x hinges (D) to the middle of the doors using 12x screws ( G ) as shown. See Clip top
BLUMOTION instructions for soft closing hinge details.
10
G - (3,5 x 16)
D - Hinge
9
90º
G
G
Step 13
Before adjusting the doors, use a spirit level to check the Base (or Top) of the unit is level front-to-back
and side in the 3 positions shown. Use alignment wedges ( M ) to make the unit level BEFORE making any
adjustment to the hinges as shown.
(İ)HEIGHT ADJUSTMENT
Loosen screws 'A' on fixing plates and move Door up or down as required. Retighten screws 'A'.
(İİ) FORWARD or BACKWARDS ADJUSTMENT
Loosen screw 'B' on fixing plate and move Door in or out as required. Retighten screw 'B'.
(İİİ) SIDEWAYS ADJUSTMENT
To move Door 'OUT' at hinge position, slacken screw 'C' slightly, then tighten screw 'B'. To move Door 'IN' at
hinge position, slacken screw 'B' slightly then tighten screw 'C'.
A
(İ)
B
(İİ)
C
(İİİ)
L
K
E - Soft Closing
Hinge
E
E
E
D
D
E
Page 9 of 12

Step 14
Please place the drawer into the unit as shown below.
Step 15
Assembly is complete.
Page 10 of 12