Argos 617/9447 User manual

Assembly Instructions - Please keep for future reference
Dimensions
Width - 80cm
Depth - 48cm
Height - 76cm
Important - Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Curved PC Trolley
issue 4 3/12/10
617/9447
617/9674

We do not
recommend the use
of power drill/ drivers
for inserting screws,
as this could damage
the unit. Only use hand
screwdrivers.
Warning: The unit weighs
approximately 22.1kgs.
Please lift with care.
●Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
●From time to time check that
there are no loose screws on this
unit.
●This product should not be
discarded with household waste.
Take to your local authority waste
disposal centre.
Note: If required the next page
can be cut out and used as a
reference throughout the
assembly. Keep this page with
these instructions for future
reference.
1
Safety and care advice
Important - Please read these instructions fully before starting assembly
Care and maintenance
Check you have all the
components and tools listed on
pages 2 and 3.
plastic bags and separate them
into their groups.
Remove all fittings from the
Keep children and animals
away from the work area, small
parts could choke if swallowed.
Make sure you have enough
space to layout the parts before
starting.
Do not stand on the panels, this
could cause damage.
Assemble the unit as close to its
final position (in the same room)
as possible.
Assemble on a soft level
surface to avoid damaging the unit
or your floor.
Parts of the assembly will be
easier with 2 people.
Dispose of all packaging carefully
and responsibly.

Components - Panels
Please check you have all the panels listed below
2
Top (80 x 48cm)
1
Left side (67.5 x 47.8cm)
2
Right side (67.5 x 47.8cm)
3
Bottom (80 x 48cm)
4
Keyboard (74.6 x 30cm)
5
Centre support (48 x 36.8cm)
6
Back support (76.8 x 16.7cm)
7
Shelf (42.5 x 24cm)
8
Cross shelf (36 x 32.8cm)
9
If you have damaged or missing components,
call the Customer Helpline:08456 400800

Locking pin x 4
Locking nut x 4Dowel x 6
45mm Screw x 17 15mm Screw x 24
Shelf support x 4
Phillips screwdriver
(medium & large)
Flatblade screwdriver
(medium)
Small
hammer Ruler/tape
measure
Components - Fittings
Please check you have all the fittings listed below
Tools required
Ruler - Use this ruler to help correctly identify the screws
AB C
DF
G
E
3
Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings
may be supplied than are required.
H
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 105 110 115 120 125 130 135 140 145 150 155 160 165 170
Runner left x 1Runner right x 1Castor x 2
I
Front castor x 2
J
Cover cap x 4
K

C
Assembly Instructions
Step 1
Fitting the runners
4
a: 2
F
Step 1
a: Use Screws to fix
the Runner left , onto
Left side 2 .
Insert Dowel into Left
side 2 .
Slide top of the runner to
access the first hole.
F
G
2
C
2
C
b:
F
H3
G
b: Use Screws to fix
the Runner right , onto
Right side .
Insert Dowel into
Right side 2 .
Slide top of the runner to
access the first hole.
F
H
3
C
3
3
H
F
3
H
F
2
G
F
2
G
F
Note: It would be useful to
ask someone to help you
at this stage.

Assembly Instructions
Step 3
5
D
4
a:
a: Use Screws to fix
Bottom ,Left side 2 ,
Right side onto the
unit.
D
2
3
4
Fitting bottom and
side panels
2
3
b: Use Screws to fix
Back support onto
Centre support 5 .
D
7
6
a: Insert Dowels into
Cross shelf .
C
9
Step 2
Fitting the centre
support
c: Use Screws to fix
Cross shelf onto the
unit.
D
9
a:
b:
9
C
6
7
D
c:
D
9
Note: It would be useful to
ask someone to help you
at this stage.
Note: It would be useful to
ask someone to help you
at this stage.
Continued on next page.

Assembly Instructions
Step 4
6
Fitting the top panel
a: Screw in Locking pins
b onto Top .
B
a:
1
B
1
b:
b: Use Locking nuts
to fix the Table top
onto the unit .
A
1
A
1
A
A
B
c: Use Screws to fix
the Front castors and
Castors onto the unit.
F
J
I
J
I
F
J
Ic:
Note: The Front
castors feature a
locking arm. We
recommend you lock
the castors when you
have finally positioned
the unit in place.
J
J
F
Step 3 - continued
b: Use Screws to fix
Left side 2 , Right side
3 onto the unit.
D
2
3
b: D
3
2
Note: It would be useful to
ask someone to help you
at this stage.

Assembly Instructions
Step 6
Fitting the shelf
7
Place Shelf supports
into the unit.
Slide shelf into the
unit.
E
Use Cover caps to
cover the screws.
K
E
8
8
Note: Adjust the shelf
supports to the desired
height.
Step 7
Cover the screws
Assembly is complete.
K
Use Screws to fix the
Keyboard onto the
unit.
F
5
Step 5
Fitting the drawer panel
5
F
Note: It would be useful to
ask someone to help you
at this stage.
If you need help or have damaged or missing parts, call the Customer Helpline : 08456 400800