Robus R2WLEDNME-01 User manual

Specication:
Information for the Product user
1. Please note the requirement to dispose of Waste Electrical & Electronic Equipment separately from household waste
(WEEE marked with crossed out wheelie bin symbol).
2. Please consider your role in contributing to re-use and recycling by returning this product at end of life to a collection
centre for waste electrical equipment or a Civic Amenity site, or to a retail outlet from which you are purchasing a
replacement.
3. This equipment may contain substances that are hazardous to health and the environment if disposed of carelessly.
It is important that it is separated from normal household waste and recycled in the WEEE chain
4. The “crossed out wheelie bin symbol” on a product indicates this equipment must not be disposed of in normal household
waste, but should be disposed of according to local WEEE regulations
Issue 1 130913
2W LED NON MAINTAINED
RECESSED EMERGENCY LIGHT
R2WLEDNME-01
Please read instruction before commencing installation and
retain for future reference.
Model No. R2WLEDNME-01
Supply Voltage: 220-240V~50/60Hz
Power Consumption : 2W
Lumen Output : 190lm
Colour Temperature: 6000-7000K
CRI: 75
Beam angle : 120o
Operating temp Range : 0°C ~ +40°C
Battery 3.6V/3.0Ah Ni-Cd
Discharge Duration >3 hours after minimum 24Hr charge
Safety Classification: Class I, Must be earthed
IP Rating: 20
Overall Diameter: 130mm
Depth: 65mm
Weight: 0.7Kg
Warranty: 2 year
Installation: Recessed
Suitable for mounting on a normally flammable surface
Complies with EN60598-1;EN60598-2-22;EN55015;EN61000-3-2;
EN61000-3-3;EN61547
ISO 9001:2008
Q UAL IT Y ASSU RE DCO MPAN Y
Dimensions:
The Installation must be carried out by an electrician
LED Group
Western Retail Park Tel: [phone]
Nangor Road Fax: [phone]
Dublin 12 Email: [email protected]
Ireland Website: www.led.ie
Page 1
Ø85mm
Cutout 75mm
Ø130mm
Cutout 75-110mm
65mm
Battery 3.6V3.0Ah
2W Energency LED

ISO 9001:2008
Q UAL IT Y ASSU RE DCO MPAN Y
The Installation must be carried out by an electrician
Testing:
Installation and Maintenance Record:
LED Group
Western Retail Park Tel: [phone]
Nangor Road Fax: [phone]
Dublin 12 Email: [email protected]
Ireland Website: www.led.ie
Page 2
The emergency lighting must be inspected and tested regularly in accordance
with local codes of practice: note: for safety reasons tests should be carried
out during daylight hours.
The minimum recommended test schedule is as follows:
After installation, allow 24 hours to ensure full battery charge and then
interrupt the supply; check after 3 hours that LED is still lighting.
1. Daily check that charge indicator led is working
2. Monthly, interrupt mains for a short period and check LED lights
3. Six-monthly, check 1 hour duration
4.At the end of year 3 and subsequently every year, check 3 hour duration:
batteries must be replaced when they can no longer support 3 hour operation.
5. Complete record sheet on installation and retain in maintenance file.
6. Update file with ongoing test records for inspection by fire officer or
Installer
Installation Type
Installation test duration & Date
Signed
Month Test
Short
Short
Short
Short
Short
Short
Short
Short
Short
1Hr.
1Hr.
3Hr.
Short
1
2
3
4
5
6
7
8
9
10
11
12
Date
xxxxx xxxxx xxxxx xxxxx
xxxxx xxxxx xxxxx xxxxx xxxxx xxxxx
1st Year
Signed Date Signed Date Signed Date Signed Date
2st Year 3st Year 4st Year 5st Year

! Electrical products can cause death or injury, or damage to property. If in any
doubt about the installation or use of this product, consult a competent
ISO 9001:2008
Q UAL IT Y ASSU RE DCO MPAN Y
The Installation must be carried out by an electrician
LED Group
Western Retail Park Tel: [phone]
Nangor Road Fax: [phone]
Dublin 12 Email: [email protected]
Ireland Website: www.led.ie
Page 3
Installation:
1. Ensure mains supply is switched off before commencing work
2. Before cutting, ensure that the hole does not impinge on joists, pipe work,
cables or other building services
Fig 2. Connect the Driver to AC power supply
220-240V,50/60Hz. Connect battery to
the driver by means of the quick fix
connector.
Fig 1. This luminaire requires a round hole
Ø75-110mm to be cut into the ceiling for
correct installation.
Fig 3. Offer the luminaire up to cut-out with the springs
being held vertically.
Put the driver and battery on the top of insulation.
Cutout Ø75-110mm with
the white strim
no use the white strim
use the white strim
Connect box
Battery 3.6V3.0Ah
2W Energency LED
Fig 4.Switch test: the green LED should come on indicating
conrrect battery charge has started. when press the switch
test, the emergency lamp will come on and the green
LED will turn off
E NL
Brown Blue
Y./G.
Information for the Product user
1. Please note the requirement to dispose of Waste Electrical & Electronic Equipment separately from household waste (WEEE
marked with crossed out wheelie bin symbol).
2. Please consider your role in contributing to re-use and recycling by returning this product at end of life to a collection centre for
waste electrical equipment or a Civic Amenity site, or to a retail outlet from which you are purchasing a replacement.
3. This equipment may contain substances that are hazardous to health and the environment if disposed of carelessly. It is important
that it is separated from normal household waste and recycled in the WEEE chain
4. The “crossed out wheelie bin symbol” on a product indicates this equipment must not be disposed of in normal household waste,
but should be disposed of according to local WEEE regulations