Rocket Fish RF-TVMFM03 User manual

1 Install the TV brackets
Option 1: Installing for a at mounting surface
1Align the TV brackets (A and B) with the screw holes on the back of the TV.
2Place the M4/M5 washers (H) or M6/M8 washers (O) over the holes in the TV brackets that
align with the screw holes on the back of the TV, then insert the M4 screws (F), M5 screws (J),
M6 screws (L or M), or M8 screws (Q) through the washers.
3Tighten the screws until they are snug against the TV bracket. Do not over tighten.
2 Add the horizontal bars
1Slide the horizontal bars (C) through the wire guides on the TV brackets.
2Secure the bars to the TV brackets using the 9/16 in. × 8/32 in. Phillips head screws (W).
Option 2: Installing for an obstructed mounting surface
Note: Use additional washers (H) with M4/M5 hardware only.
1Place the M4/M5 spacers (I) or M6/M8 spacers (P) and the M4/M5 washers (H) into the
recessed screw holes on the back of the TV.
2Align the TV brackets (A and B) with the spacers and washers on the back of the TV.
3Place the M4/M5 washers (H) or M6/M8 washers (O) over the holes in the TV brackets that
align with the screw holes on the back of the TV, then insert the M4 screws (G), M5 screws (K),
M6 screws (N), or M8 screws (R or S) through the washers.
4Tighten the screws until they are snug against the TV bracket. Do not over tighten.
QUICK SETUP GUIDE
RF-TVMFM03
Tools you will need:
• Stud nder
• Awl
• Pencil
• Level
• Tape measure
• Phillips screwdriver
• Socket wrench with
1/2 in. socket or
adjustable wrench
• 7/32 in. wood drill bit
• Power drill
Package contents
ARight vertical TV bracket (1)
BLeft vertical TV bracket (1)
CHorizontal TV bracket (2)
DArm assembly (1)
EWall plate (1)
M4 bag
FM4 × 12 mm screws (4)
GM4 × 30 mm screws (4)
HM4/M5 washers (8)
IM4/M5 spacers (4)
M5 bag
JM5 × 12 mm screws (4)
KM5 × 30 mm screws (4)
M6 bag
LM6 × 12 mm screws (4)
MM6 × 20 mm screws (4)
NM6 × 35 mm screws (4)
OM6/M8 washers (4)
PM6/M8 spacers (4)
Thank you for choosing the Rocketsh RF-TVMFM03.
The RF-TVMFM03 TV mount is designed to support a
at-panel TV weighing up to 130 lbs. (58.9 kg).
M8 bag
QM8 × 16 mm screws (4)
RM8 × 40 mm screws (4)
SM8 × 60 mm screws (4)
Hex key bag
T3/16 in. hex key (1)
Lag bolt bag
ULag bolt washer (4)
V5/16 in. × 2-3/4 in. lag bolt (4)
Bracket hardware
W9/16 in. × 8/32 in. Phillips head screw (4)
X3/8 in. × 8/32 in. Phillips head screw (1)
Cable ties
Y8 in. nylon cable ties (5)
Cap screws
Z5/32 in. hex key (1)
AA Cap screws (2)
A B C
DE
M4 bag
Cap screws with hex key
M5 bag
M6 bag
Bracket hardware
M8 bag
Hex key bag Cable ties
Lag bolt bag
M4 ×12 mm
F
M4 ×30 mm
G
M5 ×12 mm
J K
M8 ×16 mm
Q
M8 ×40 mm
R
M8 ×60 mm
S
M6/M8
P
M4/M5
I
M6/M8
O
M4/M5
H
TY
M6 ×12 mm
L
M6 ×20 mm
M
M6 ×35 mm
N
WX
AA
VU Z
M5 ×30 mm
5/32 in.
5/16 in. × 2-3/4 in.
3/16 in.
3 Install the wall plate to a wood stud wall
Note: Any material covering the wall must not exceed 5/8 in. (16 mm).
1Locate the studs. Verify the center of the stud with an awl
or thin nail or use an edge-to-edge stud nder.
2Level the wall plate (E) and mark the hole locations.
3Drill pilot hole to a depth of 3 in. using a 7/32 in. diameter drill bit.
4Align the wall plate (E) with the pilot holes.
5Place the washers (U) over the holes in the wall plate (E),
insert the lag bolts (V) through the washers, then tighten
the lag bolts only until the washers (U) are pulled rmly
against the wall plate.
CAUTION: Avoid potential
injuries or property damage!
DO NOT over-tighten
the lag bolts (V).
10-1/5 in. 7 in.
TV shifts 7 in. from the home position to
full extension.
16 in.
<5/8 in.
Note: Intended for use on
wood stud walls with 16 in.
or less spacing only.
R
or
or
or
or
or
(75 mm)
3 in.
Wall
TV
C
M
Y
CM
MY
CY
CMY
K
RF-TVMFM03_10-0726_QSG_V2_EN.eps 1 7/2/2010 1:18:59 PMRF-TVMFM03_10-0726_QSG_V2_EN.eps 1 7/2/2010 1:18:59 PM

5-year limited warranty
Visit www.rocketshproducts.com for details.
We’re here for you
www.rocketshproducts.com
For customer service, call:
800-620-2790 (U.S./Canada markets)
© 2010 BBY Solutions, Inc., All Rights Reserved.
Distributed by Best Buy Purchasing, LLC 7601 Penn Avenue South, Richeld, MN USA 55423-3645
Distribuido por Best Buy Purchasing, LLC
Best Buy Imports, S. de R.L. de C.V. Av. Santa Fe 485, Segundo Piso, Colonia Cruz Manca, Programa Parcial de Desarrollo Santa
Fe, Delegación Cuajimalpa, Distrito Federal, México 05349
ROCKETFISH is a trademark of BBY Solutions, Inc. All other products and brand names are trademarks of their respective
owners.
6907-002019 <00>
ENGLISH 10-0726
4 Add the arm assembly to the wall plate
1Hang the upper lip of the arm assembly (D) over the top lip on the wall plate (E),
then lower the bottom lip of the arm assembly into the bottom lip on the wall plate.
2Secure the arm assembly (D) with the two cap screws (AA) using the 5/32 in. hex key (Z).
8 Manage the cables
Use cable ties (Y) to bundle and secure TV cables to the arm assembly.
HEAVY! You will need
assistance with this step.
5 Add the TV/bracket to arm assembly
1Slide the top and bottom edges of the arm assembly under the metal tabs on the
TV horizontal brackets (C).
2Align the center hole in the lower horizontal bar (C) with the hole in the face of
the arm assembly (D) and secure the TV with the bracket screw (X).
6 Adjust the viewing angle
When the television is mounted onto the arm assembly and secured, it can be adjusted
to make it level.
1Loosen the two screws on the arm assembly using the 5/32 in. hex key (Z).
2Adjust the TV ± 6° either clockwise or counter-clockwise.
3Retighten the screws.
7 Adjust the swivel tension
Adjust the swivel tension using the 5/32 in. hex key (Z).
9 Adjust the tilt
Adjust the tilt of the TV forward or backward 10° using your ngers or the 3/16 in. hex
key (T).
IMPORTANT SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS
CAUTION: Do not use this product for any purpose not explicitly specied by Rocketsh. Improper
installation may cause property damage or personal injury. If you do not understand these directions, or
have doubts about the safety of the installation, contact Customer Service or call a qualied contractor.
Rocketsh is not responsible for damage or injury caused by incorrect installation or use.
The weight of your TV must not exceed 130 lb (58.9 kg).The wall must be capable of supporting ve
times the weight of the TV and wall mount combined.
This product contains small items that could be a choking hazard if swallowed. Keep these items away
from young children!
11° 11°
Leveling
C
M
Y
CM
MY
CY
CMY
K
RF-TVMFM03_10-0726_QSG_V2_EN.eps 2 7/2/2010 1:19:11 PMRF-TVMFM03_10-0726_QSG_V2_EN.eps 2 7/2/2010 1:19:11 PM