Rockwell Automation Allen-Bradley Kinetix 350 User manual

Installation Instructions
Kinetix 350 Single-axis EtherNet/IP Servo
Drives
Catalog Numbers 2097-V31PR0-LM, 2097-V31PR2-LM, 2097-V32PR0-LM,
2097-V32PR2-LM, 2097-V32PR4-LM, 2097-V33PR1-LM, 2097-V33PR3-LM,
2097-V33PR5-LM, 2097-V33PR6-LM, 2097-V34PR3-LM, 2097-V34PR5-LM,
2097-V34PR6-LM
About the Kinetix 350 Drives
Kinetix® 350 single-axis EtherNet/IP servo drives provide an Ethernet enabled solution for
applications with output power requirements in the range of 0.4…3.0 kW (2…12 A rms).
Refer to the Kinetix 350 Single-axis EtherNet/IP Servo Drives User Manual, publication
2097-UM002, for detailed information on wiring, applying power, troubleshooting,
and integration with ControlLogix®, or CompactLogix® controller platforms.
Topic Page
About the Kinetix 350 Drives 1
Important User Information 2
Catalog Number Explanation 3
Before You Begin 4
Install the Kinetix 350 Drive 4
Connector Data 7
Power Wiring Requirements 11
Additional Resources 15

2Kinetix 350 Single-axis EtherNet/IP Servo Drives
Rockwell Automation Publication 2097-IN008B-EN-P - October 2011
Important User Information
Solid-state equipment has operational characteristics differing from those of electromechanical equipment. Safety Guidelines for
the Application, Installation and Maintenance of Solid State Controls (Publication SGI-1.1 available from your local Rockwell
Automation sales office or online at http://www.rockwellautomation.com/literature/) describes some important differences
between solid-state equipment and hard-wired electromechanical devices. Because of this difference, and also because of the
wide variety of uses for solid-state equipment, all persons responsible for applying this equipment must satisfy themselves that
each intended application of this equipment is acceptable.
In no event will Rockwell Automation, Inc. be responsible or liable for indirect or consequential damages resulting from the use or
application of this equipment.
The examples and diagrams in this manual are included solely for illustrative purposes. Because of the many variables and
requirements associated with any particular installation, Rockwell Automation, Inc. cannot assume responsibility or liability for
actual use based on the examples and diagrams.
No patent liability is assumed by Rockwell Automation, Inc. with respect to use of information, circuits, equipment, or software
described in this manual.
Reproduction of the contents of this manual, in whole or in part, without written permission of Rockwell Automation, Inc., is
prohibited.
Throughout this manual, when necessary, we use notes to make you aware of safety considerations.
WARNING: Identifies information about practices or circumstances that can cause an explosion in a
hazardous environment, which may lead to personal injury or death, property damage, or economic loss.
ATTENTION: Identifies information about practices or circumstances that can lead to personal injury or
death, property damage, or economic loss. Attentions help you identify a hazard, avoid a hazard and
recognize the consequences.
SHOCK HAZARD: Labels may be on or inside the equipment, for example, drive or motor, to alert people that
dangerous voltage may be present.
BURN HAZARD: Labels may be on or inside the equipment, for example, drive or motor, to alert people that
surfaces may reach dangerous temperatures.
IMPORTANT Identifies information that is critical for successful application and understanding of the product.

Kinetix 350 Single-axis EtherNet/IP Servo Drives 3
Rockwell Automation Publication 2097-IN008B-EN-P - October 2011
Catalog Number Explanation
This publication applies to the following Kinetix 350 drives.
Kinetix 350 Drives, Single-phase
Cat. No. Description
2097-V31PR0-LM 120/240V, 1 Ø, 2.0 A
2097-V31PR2-LM 120/240V, 1 Ø, 4.0 A
2097-V32PR0-LM 240V, 1 Ø, 2.0 A, with integrated filter
2097-V32PR2-LM 240V, 1 Ø, 4.0 A, with integrated filter
2097-V32PR4-LM 240V, 1 Ø, 8.0 A, with integrated filter
Kinetix 350 Drives, Single/Three-phase
Cat. No. Description
2097-V33PR1-LM 240V, 1 Ø or 3 Ø, 2.0 A
2097-V33PR3-LM 240V, 1 Ø or 3 Ø, 4.0 A
2097-V33PR5-LM 240V, 1 Ø or 3 Ø, 8.0 A
2097-V33PR6-LM 240V, 1 Ø or 3 Ø, 12.0 A
Kinetix 350 Drives, Three-phase
Cat. No. Description
2097-V34PR3-LM 480V, 3 Ø, 2.0 A
2097-V34PR5-LM 480V, 3 Ø, 4.0 A
2097-V34PR6-LM 480V, 3 Ø, 6.0 A

4Kinetix 350 Single-axis EtherNet/IP Servo Drives
Rockwell Automation Publication 2097-IN008B-EN-P - October 2011
Before You Begin
Remove all packing material, wedges, and braces from within and around the components. After
unpacking, check the item nameplate catalog number against the purchase order.
Parts List
The Kinetix 350 drive ships with the following:
•General-purpose power input (IPD) header, back-up power (BP) header, shunt resistor
and DC bus (BC) header, motor power (MP) header, and safe torque off (STO) header
•A ground clamp that also provides strain relief for motor power cable
•These installation instructions, publication 2097-IN008
Install the Kinetix 350 Drive
These procedures assume you have prepared your panel, and understand how to bond your
system. For installation instructions regarding equipment and accessories not included here, refer
to the instructions that came with those products.
TIP
The connector kit for motor feedback (catalog number 2090-K2CK-D15M) is not provided.
Replacement connector sets (catalog number 2097-CONN1) are also available. Refer to the
Kinetix Motion Control Selection Guide, publication GMC-SG001, for more information on
connector kits and replacement connector sets.
SHOCK HAZARD: To avoid hazard of electrical shock, perform all mounting and wiring of the
Kinetix 350 drive prior to applying power. Once power is applied, connector terminals may have
voltage present even when not in use.
ATTENTION: Plan the installation of your system so that you can perform all cutting, drilling,
tapping, and welding with the system removed from the enclosure. Because the system is of the
open type construction, be careful to keep any metal debris from falling into it. Metal debris or
other foreign matter can become lodged in the circuitry, which can result in damage to
components.

Kinetix 350 Single-axis EtherNet/IP Servo Drives 5
Rockwell Automation Publication 2097-IN008B-EN-P - October 2011
Mount the Kinetix 350 Drive
Follow these steps to mount the drive.
1. Observe these clearance requirements when mounting the drive to the panel. .
IMPORTANT
Mount the module in an upright position as shown. Do not mount the module on
its side.
Drive
Cat. No.
Dimensions A
mm (in.)
2097-V31PR0-LM
185 (7.29)
2097-V31PR2-LM
2097-V32PR0-LM
230 (9.04)2097-V32PR2-LM
2097-V32PR4-LM
2097-V33PR1-LM
185 (7.29) (1)
(1) If using an AC line filter, add 50 mm (2
in.).
2097-V33PR3-LM
2097-V33PR5-LM
2097-V33PR6-LM 230 (9.04)
2097-V34PR3-LM
185 (7.29) (1)
2097-V34PR5-LM
2097-V34PR6-LM 230 (9.04)
A
25 mm (1.0 in.) Clearance
for Airow and Installation
25 mm (1.0 in.) Clearance
for Airow and Installation
3 mm (0.12 in.)
Side Clearance
3 mm (0.12 in.)
Side Clearance
•Additional clearance and different hole patterns are required for side
mount and rear mount AC line filters. See the table and step 2for more
details.
•Additional clearance is required depending on the other accessory
items installed.
•Additional clearance is required for the cable and wires connected to
the top, front, and bottom of the drive.
•Additional 150 mm (6.0 in.) is required when the drive is mounted
adjacent to noise sensitive equipment or clean wire ways.
Refer to page 6for Kinetix 350 drive dimensions.

6Kinetix 350 Single-axis EtherNet/IP Servo Drives
Rockwell Automation Publication 2097-IN008B-EN-P - October 2011
2. Mount the Kinetix 350 drive to the cabinet sub-panel with a M4 (#6-32) steel machine
screw torqued to 1.1 N•m (9.8 lb•in).
For catalog numbers 2097-V33PR1-LM, 2097-V33PR3-LM, 2097-V33PR5-LM,
2097-V34PR3-LM, and 2097-V34PR5-LM that will be using an AC line filter, refer to
the AC Line Filter Installation Instructions, publication 2097-IN003, for sub-panel
mounting hole pattern.
Kinetix 350 Drive Mounting Dimensions
Dimensions mm (in.) Dimensions mm (in.)
Cat. No. A B Cat. No. A B
2097-V31PR0-LM 185.1 (7.29) 68.0 (2.68) 2097-V33PR3-LM 185.1 (7.29) 68.5 (2.70)
2097-V31PR2-LM 185.1 (7.29) 68.5 (2.70) 2097-V33PR5-LM 185.1 (7.29) 94.4 (3.72)
2097-V32PR0-LM 229.6 (9.04) 68.0 (2.68) 2097-V33PR6-LM 229.6 (9.04) 68.0 (2.68)
2097-V32PR2-LM 229.6 (9.04) 68.5 (2.70) 2097-V34PR3-LM 185.1 (7.29) 68.5 (2.70)
2097-V32PR4-LM 229.6 (9.04) 86.8 (3.42) 2097-V34PR5-LM 185.1 (7.29) 94.4 (3.72)
2097-V33PR1-LM 185.1 (7.29) 68.0 (2.68) 2097-V34PR6-LM 229.6 (9.04) 68.0 (2.68)
11.8
(0.46)
6.6
(0.26)
7.1
(0.28)
B
38.1
(1.5)
182
(7.18)
190
(7.50)
30.8
(1.21)
Ø 4.57
(0.18) 3x
A
238
(9.37)
61.0
(2.40)
9.7
(0.38)
5.0
(0.19)
Dimensions are in mm (in.).

Kinetix 350 Single-axis EtherNet/IP Servo Drives 7
Rockwell Automation Publication 2097-IN008B-EN-P - October 2011
Connector Data
Use this illustration to identify the Kinetix 350 drive features and indicators.
Kinetix 350 Drive Features and Indicators
Item Description
1 Data status indicator and diagnostic display
2 Memory module socket
3Networkstatusindicator
4 Module status indicator
5 Axis status indicator
6 Ethernet communication port (Port 1)
7 I/O (IOD) connector
8 Motor feedback (MF) connector
9GroundLug
10 Shunt resistor and DC bus (BC) connector
11 Back-up power (BP) connector
12 Display control push buttons (3)
13 Mains (IPD) connector
14 Motor power (MP) connector
15 Safe torque-off (STO) connector
12
11
10
8
7
2
1
9
9
3
4
5
6
13 15
Top View
(2097-V33PR5-LM
Kinetix 350
drive is shown)
Bottom View
(2097-V33PR5-LM
Kinetix 350
drive is shown)
14

8Kinetix 350 Single-axis EtherNet/IP Servo Drives
Rockwell Automation Publication 2097-IN008B-EN-P - October 2011
Kinetix 350 Drive Connectors
Mains (IPD) Connector
Pin Orientation for 8-pin Ethernet Communication Port (port 1)
Designator Description Connector
IPD AC mains input power 4-position plug/header
PORT1 Ethernet communication port RJ45 Ethernet
IOD I/O SCSI 50 pin high density connector
MF Motor feedback 15-pin high-density D-shell (male)
BP Back-up power 2-pin quick-connect terminal block
BC Brake resistor and DC bus 5-pin quick-connect terminal block
MP Motor power 6-pin quick-connect terminal block
STO Safe torque off (STO) terminal 6-pin quick-connect terminal block
IPD Pin Description Signal
1 Protective earth (ground) PE
2ACpowerin L1
3ACpowerin L2
4 AC power in (3-phase models) L3
Port 1 Pin Description Signal
1 Transmit port (+) data terminal + TX
2 Transmit port (-) data terminal - TX
3 Receive port (+) data terminal + RX
4— —
5— —
6 Receive port (-) data terminal - RX
7— —
8— —
1
8

Kinetix 350 Single-axis EtherNet/IP Servo Drives 9
Rockwell Automation Publication 2097-IN008B-EN-P - October 2011
I/O (IOD) Connector Pinout
IOD Pin Description Signal
1…25 Reserved —
5 Drive logic common GND
6…25 Reserved —
26 +/- Overtravel, enable and home common COM
27 Negative hardware overtravel NEG_OT
28 Positive hardware overtravel POS_OT
29 Drive enable ENABLE
30 Home switch HOME_SW
31…35 Reserved —
36 Registration common REG_COM
37…38 Reserved —
39 Registration input REG
40…42 Reserved —
43 Brake release positive BRAKE+
44 Brake release negative BRAKE-
44…50 Reserved —
1
25 50
26

10 Kinetix 350 Single-axis EtherNet/IP Servo Drives
Rockwell Automation Publication 2097-IN008B-EN-P - October 2011
Motor Feedback (MF) Connector Pinout
Control Power Back-up (BP) Pinout
MF Pin Description Signal
1 Sine differential input+
AM+ Differential input+
SIN+
AM+
2 Sine differential input-
AM- Differential input-
SIN-
AM-
3 Cosine differential input+
BM+ Differential input+
COS+
BM+
4 Cosine differential input-
BM- Differential input-
COS-
BM-
5 Data differential input +
Index pulse+
DATA+
IM+
6Common ECOM
7 Encoder power (+9V) EPWR_9V (2)
(2) Encoder power supply uses either 5V or 9V DC based on encoder/motor used.
8 Single-ended 5V Hall effect commutation S3
9 Reserved —
10 Data differential input -
Index pulse-
DATA-
IM-
11 Motor thermal switch (normally closed) (1)
(1) Not applicable unless motor has integrated thermal protection.
TS
12 Single-ended 5V Hall effect commutation S1
13 Single-ended 5V Hall effect commutation S2
14 Encoder power (+5V) EPWR_5V (2)
15 Reserved —
BP Pin Description Signal
1 Positive 24V DC +24V DC
2 24V DC power supply return Return
Pin 11
Pin 6
Pin 15
Pin 1
Pin 10
Pin 5

Kinetix 350 Single-axis EtherNet/IP Servo Drives 11
Rockwell Automation Publication 2097-IN008B-EN-P - October 2011
Shunt Resistor and DC Bus (BC) Pinout
Motor Power (MP) Pinout
Safe Torque Off (STO) Pinout
The Kinetix 350 drive ships with the safe torque off enabled. Connect the safe torque off inputs
to a safety circuit, or install motion-allowed jumpers to obtain motion. Refer to the Kinetix 350
Single-axis EtherNet/IP Servo Drive User Manual, publication 2097-UM002, for details.
Power Wiring Requirements
Wire should be copper with 75 C (167 F) minimum rating. Phasing of main AC power is
arbitrary and earth ground connection is required for safe and proper operation.
BC Pin Description Signal
1…2 Positive DC bus/brake resistor B+
3 Brake resistor BR
4…5 Negative DC bus B-
MP Pin Description Signal
1 Motor power out U
2 Motor power out V
3 Motor power out W
4 Protective earth (ground) PE
STO Pin Description Signal
1 +24V DC output from the drive +24V DC control
2 +24V DC output common Control COM
3 Safety status Safety Status
4 Safety input 1 (+24V DC to enable) Safety Input 1
5 Safety common Safety COM
6 Safety input 2 (+24V DC to enable) Safety Input 2
IMPORTANT
The National Electrical Code and local electrical codes take precedence over the values and
methods provided.

12 Kinetix 350 Single-axis EtherNet/IP Servo Drives
Rockwell Automation Publication 2097-IN008B-EN-P - October 2011
Kinetix 350 Drive Power Wiring Requirements
Cat. No. Description
Terminals Recommended
Wire Size
mm2 (AWG)
Strip
Length
mm (in.)
Torque Value
N•m (lb•in)
Pin Signal
2097-V31PR0-LM
2097-V32PR0-LM
2097-V32PR2-LM
2097-V33PR1-LM
2097-V33PR3-LM
2097-V34PR3-LM
2097-V34PR5-LM
2097-V34PR6-LM
Mains input
power
L3
L2
L1
PE
2.5 (14) 7 (0.28) 0.5 (4.5)
2097-V32PR4-LM
2097-V33PR5-LM 4.0 (12) 7 (0.28) 0.5 (4.5)
2097-V31PR2-LM
2097-V33PR6-LM 6.0 (10) 7 (0.28) 0.56…0.79 (5.0…7.0)
2097-V31PR0-LM
2097-V32PR0-LM
2097-V32PR2-LM
2097-V32PR4-LM
2097-V33PR1-LM
2097-V33PR3-LM
2097-V33PR5-LM
2097-V34PR3-LM
2097-V34PR5-LM
2097-V34PR6-LM
2097-V31PR2-LM
Motor power
PE
W
V
U
2.5 (14) 7 (0.28) 0.5 (4.5)
2097-V33PR6-LM 4.0 (12) 7 (0.28) 0.5 (4.5)
2097-V31PR0-LM
2097-V32PR0-LM
2097-V32PR2-LM
2097-V32PR4-LM
2097-V33PR1-LM
2097-V33PR3-LM
2097-V33PR5-LM
2097-V34PR3-LM
2097-V34PR5-LM
2097-V34PR6-LM
2097-V31PR2-LM
Brake resistor
and DC bus(1)
B+
B+
BR
B-
B-
2.5 (14) 7 (0.28) 0.5 (4.5)
2097-V33PR6-LM 4.0 (12) 7 (0.28) 0.5 (4.5)
2097-V3xPRx-LM Control
back-up power
+24V DC
Return
1.5 (16) 6 (0.25) 0.5 (4.5)
2097-V3xPRx-LM Safe torque off
STO-1 (2)
STO-2 (2)
STO-3
STO-4
STO-5
STO-6
+24V DC Control
Control COM
Safety Status
Safety Input 1
Safety COM
Safety Input 2
(1) Use for shunt resistor connection only.
(2) Use for bypassing the STO circuit only.

Kinetix 350 Single-axis EtherNet/IP Servo Drives 13
Rockwell Automation Publication 2097-IN008B-EN-P - October 2011
Ground Your Kinetix 350 Drive to the Subpanel
If the Kinetix 350 drive is mounted on a painted subpanel, ground to a bonded cabinet ground
bus with a braided ground strap or 4.0 mm2 (12 AWG) solid copper wire 100 mm (3.9 in.) long.
Connecting the Braided Ground Strap Example
For dimensions, see Kinetix 350 Drive Mounting Dimensions on page 6.
ATTENTION: To avoid personal injury and/or equipment damage, make sure installation complies
with specifications regarding wire types, conductor sizes, branch circuit protection, and disconnect
devices. The National Electrical Code (NEC) and local codes outline provisions for safely installing
electrical equipment.
To avoid personal injury and/or equipment damage, make sure motor power connectors are used
for connection purposes only. Do not use them to turn the unit on and off.
To avoid personal injury and/or equipment damage, make sure shielded power cables are
grounded to prevent potentially high voltages on the shield.
Bonded Cabinet
Ground Bus
Ground Grid or Power
Distribution Ground
Braided
Ground Strap
Ground Stud

14 Kinetix 350 Single-axis EtherNet/IP Servo Drives
Rockwell Automation Publication 2097-IN008B-EN-P - October 2011
Kinetix 350 Drive Motor-power Wire Shielding
A motor-power ground clamp and two #6-32 x 1 screws are supplied with the Kinetix 350 drive.
Install the supplied motor power ground clamp within 50…75 mm (2…3 in.) of the drive by
using the two #6-32 x 1 screws.
Motor Power Ground Clamp Installation
50…75
(2…3)
50…75
(2…3)
34.0
(1.34)
25
(1.0)
12.7
(0.50)
If panel is painted, remove paint to provide
metal-to-metal contact.
Motor Power Ground Clamp
Dimension are in mm (in.).

Kinetix 350 Single-axis EtherNet/IP Servo Drives 15
Rockwell Automation Publication 2097-IN008B-EN-P - October 2011
Additional Resources
These documents contain additional information concerning related products from Rockwell
Automation.
You can view or download publications at http://www.rockwellautomation.com/literature. To
order paper copies of technical documentation, contact your local Allen-Bradley® distributor or
Rockwell Automation sales representative.
Resource Description
Kinetix 350 Single-axis EtherNet/IP Servo Drives User Manual,
publication 2097-UM002
Information on installing, configuring, starting up,
troubleshooting, and specifications for your Kinetix 350 servo
drive system.
Kinetix 300 Shunt Resistor Installation Instructions, publication
2097-IN002
Information on installing and wiring Kinetix 300 shunt resistors.
Kinetix 300 AC Line Filter Installation Instructions, publication
2097-IN003
Information on installing and wiring the Kinetix 300 AC line
filter.
Kinetix 300 I/O Terminal Expansion Block Installation
Instructions, publication 2097-IN005
Information on installing and wiring the Kinetix 300 I/O
terminal expansion block.
Kinetix 300 Memory Module Installation Instructions,
publication 2097-IN007
Information on installing the Kinetix 300 memory module.
Kinetix 300 Memory Module Programmer Quick Start,
publication 2097-QS001
Information on using the memory module programmer to
duplicate the memory module.
Industrial Automation Wiring and Grounding Guidelines,
publication 1770-4.1
Provides general guidelines for installing a Rockwell
Automation industrial system.
Product Certifications website, http://www.ab.com Provides declarations of conformity, certificates, and other
certification details.

Rockwell Automation Publication 2097-IN008B-EN-P - October 2011 PN-124737
Supersedes Publication 2097-IN008A-EN-P - June 2011 Copyright © 2011 Rockwell Automation, Inc. All rights reserved. Printed in the U.S.A.
Rockwell Automation Support
Rockwell Automation provides technical information on the Web to assist you in using its products. At
http://www.rockwellautomation.com/support/, you can find technical manuals, a knowledge base of FAQs, technical and application
notes,sample code and links tosoftware service packs, and a MySupport feature that you can customize to make the best use of these
tools.
For an additional level of technical phone support for installation, configuration and troubleshooting, we offer TechConnectSM support
programs. For more information, contact your local distributor or Rockwell Automation representative, or visit
http://www.rockwellautomation.com/support/.
Installation Assistance
If you experience a problem within the first 24 hours of installation, please review the information that's contained in this manual.
You can also contact a special Customer Support number for initial help in getting your product up and running.
New Product Satisfaction Return
Rockwell Automation tests all of its products to ensure that they are fully operational when shipped from the manufacturing facility.
However, if your product is not functioning and needs to be returned, follow these procedures.
Documentation Feedback
Your comments will help us serve your documentation needs better. If you have any suggestions on how to improve this document,
complete this form, publication RA-DU002, available at http://www.rockwellautomation.com/literature/.
United States or Canada 1.440.646.3434
Outside United States or
Canada
Use the Worldwide Locator at
http://www.rockwellautomation.com/support/americas/phone_en.html, or contact your local
Rockwell Automation representative.
United States Contact your distributor. You must provide a Customer Support case number (call the phone number
above to obtain one) to your distributor to complete the return process.
Outside United States Please contact your local Rockwell Automation representative for the return procedure.
Allen-Bradley, CompactLogix, ControlLogix, Kinetix, Rockwell Software, Rockwell Automation, and TechConnect are trademarks of Rockwell
Automation, Inc.
Rockwell Otomasyon Ticaret A.Ş., Kar Plaza İş Merkezi E BlokKat:6 34752 İçerenköy, İstanbul, Tel: [phone]