Rockwell Automation Allen-Bradley Kinetix TLP Series User manual

Installation Instructions
Original Instructions
Kinetix TLP Multi-purpose Servo Motors
with 046…235 mm Frame Size
Catalog Numbers TLP-A046-005, TLP-A046-010, TLP-A070-020, TLP-A070-040, TLP-A090-075, TLP-A100-100, TLP-A115-100,
TLP-A115-200, TLP-A145-050, TLP-A145-090, TLP-A145-100, TLP-A145-150, TLP-A200-200, TLP-A200-300, TLP-A200-350,
TLP-A200-450, TLP-A200-550, TLP-A200-750, TLP-A235-11K, TLP-A235-15K
About the Kinetix TLP Servo Motors
Kinetix® TLP servo motors, tested and validated for optimal performance with Kinetix 5100 servo drives, are available with or without 24V DC
holding brakes, and a wide-range of other economical and customizable options.
You are responsible for inspecting the equipment before accepting the shipment from the freight company. Check the items you receive against your
purchase order. Notify the carrier of shipping damage or missing items immediately. Store or operate your motor in a clean and dry location within
the Environmental Specifications on page 15.
Topic Page Topic (continued) Page
About the Kinetix TLP Servo Motors 1 Motor Dimensions (200 and 235 mm frame sizes) 8
Catalog Number Explanation 2 Connector Data 9
Before You Install the Motor 2 Load Force Ratings 10
Motor Installation 4 Environmental Specifications 15
Motor Dimensions (046…100 mm frame sizes) 6 Motor Accessories 15
Motor Dimensions (115 and 145 mm frame sizes) 7 Additional Resources 16
ATTENTION: To avoid personal injury and damage to the motor, do not lift or handle the motor by the motor shaft or on-motor cable (when present). The cap on
the shaft can come loose and cause you to drop the motor. Stress on the on-motor cable can disrupt the power and signal connectivity.

2Rockwell Automation Publication TLP-IN001A-EN-P - October 2019
Kinetix TLP Servo Motors with 046…235 mm Frame Size
Catalog Number Explanation
(1) Multi-turn revolution depends on the system settings and configuration.
(2) Rated power hierarchy is only for comparative purposes. Use Motion Analyzer to size and select motors for your application, and/or the torque/speed curves in the Kinetix 5100 Drive Systems Design Guide,
publication KNX-RM011.
Before You Install the Motor
Perform these inspection steps and review the guidelines for shaft seals, couplings and pulleys, and electrical noise prevention.
1. Remove the motor carefully from its shipping container.
2. Visually inspect the motor for any damage.
3. Examine the motor frame, front output shaft, and mounting pilot for any defects.
4. Notify the carrier of shipping damage immediately.
Remove the Shaft Cap
Remove the protective cap installed on the motor shaft by hand pressure only. Do not use a hammer or other tools as they can damage the motor
shaft and shaft seal.
ATTENTION: Do not attempt to open and modify the motor. Only a qualified Rockwell Automation employee can service this motor.
TL P - A xxx - xxx - Dx xx x x
Factory Options
A = Standard (without shaft seal)
S = Shaft seal
Brake
2 = No brake
4 = 24V DC holding brake
Shaft Key
J = Shaft key
K = Smooth shaft
Connector
A3 = Rectangular connectors with 0.3 mm (11.8 in.) on-motor cables
A1 = Rectangular connectors with 1.0 mm (39.4 in.) on-motor cables
MC = Military style connectors forTLP-A115-xxx and TLP-A145-xxx motors
MD = Military style connectors for TLP-A200-200, TLP-A200-300, TLP-A200-350, TLP-A200-450 motors
ME = Military style connectors for TLP-A200-550,TLP-A200-750, and TLP-A235-xxx motors
Rated Power (2)
005 = 50 W 075 = 750 W 200 = 2.0 kW 550 = 5.5 kW
010 = 100 W 090 = 900 W 300 = 3.0 kW 750 = 7.5 kW
020 = 200 W 100 = 1.0 kW 350 = 3.5 kW 11K = 11 kW
040 = 400 W 150 = 1.5 kW 450 = 4.5 kW 15K = 15 kW
050 = 500 W
Frame Size - Bolt Circle Diameter (BCD)
046 = 46 mm 115 = 115 mm
070 = 70 mm 145 = 145 mm
090 = 90 mm 200 = 200 mm
100 = 100 mm 235 = 235 mm
Voltage Class
A = 200V
Series Type
P = Multi-purpose
Series
TL = Kinetix TLP multi-purpose servo motors that are optimized to the ratings of Kinetix 5100 servo drives.
Feedback
D = 24-bit absolute single-turn and multi-turn (65,536 revolutions capable) with battery enabled encoder. (1)

Rockwell Automation Publication TLP-IN001A-EN-P - October 2019 3
Kinetix TLP Servo Motors with 046…235 mm Frame Size
Prolong Motor Life
Proper design and maintenance can increase the life of a servo motor. Follow these guidelines to maximize the life of a servo motor operated within
the Environmental Specifications on page 15:
•Always provide a drip loop to carry liquids away from the connection to the motor.
• Whenever possible, provide shields that protect the motor housing, shaft, seals, and their junctions from contamination by foreign matter
or fluids.
• Shaft seals are subject to wear and require periodic inspection and replacement. Replacement is recommended every 3 months, not to
exceed 12 months, depending on use. See Shaft Seal Kits on page 15 for more information.
• Inspect the motor and seals for damage or wear on a regular basis. If you detect damage or excessive wear, replace the item.
• The brake option on this servo motor is a spring-set holding brake that releases when voltage is applied to the brake coil. A separate power
source is required to disengage the brake. This power source can be applied by a servo motor controller or manual operator control.
If system main power fails, holding brakes can withstand occasional use as stopping brakes. However, this creates rotational mechanical
backlash that can cause damage to the system, increase brake wear, and reduce brake life.
Shaft Seals
An additional seal is required on the motor shaft near the motor front bearing if the shaft is exposed to significant amounts of fine dust or fluids,
such as lubricating oil from a gearbox. An IP65 rating for the motor requires a shaft seal and environmentally sealed connectors and cables.
The additional seal is not recommended in applications where the motor shaft area is free of liquids or fine dust, and a lower rating is sufficient:
•SeeEnvironmental Specifications on page 15 for a brief description of the IP rating for these motors.
•SeeShaft Seal Kits on page 15 for seal kits compatible with your motor.
• See Kinetix Rotary Motion Specifications Technical Data, publication KNX-TD001, for Bulletin 2090 cables with environmentally sealed
connectors compatible with these motors.
Couplings and Pulleys
Mechanical connections to the motor shaft, such as couplings and pulleys, require a torsionally rigid coupling or a reinforced timing belt. The high
dynamic performance of servo motors can cause couplings, pulleys, or belts to loosen or slip over time. A loose or slipping connection causes system
instability and can damage the motor shaft. All connections between the system and the servo motor shaft must be rigid to achieve acceptable
response from the system. Periodically inspect connections to verify their rigidity.
When mounting couplings or pulleys to the motor shaft, verify that the connections are properly aligned and that axial and radial loads are within
the specifications of the motor. See Load Force Ratings on page 10 for guidelines to achieve 40,000 hours of motor bearing life.
IMPORTANT
Holding brakes are not designed to stop rotation of the motor shaft, and they are not intended to be used as a safety device. They are designed to
hold a motor shaft at 0 rpm for loads up to the rated brake holding torque. Follow these steps to prevent motor shaft rotation.
1. Command the servo drive to 0 rpm.
2. Verify the motor is at 0 rpm.
3. Engage the brake.
4. Disable the drive.
Disabling the drive removes the potential for brake wear caused by a badly-tuned servo system oscillating the shaft.
Correct: Position the motor so that the cable enters from beneath
the motor and forms a drip loop.
This configuration applies to
TLP-A046-xxx, TLP-A070-xxx,
TLP-A090-075, and TLP-A100-xxx motors.
This configuration applies to
TLP-A115-xxx, TLP-A145-xxx,
TLP-A200-xxx, and TLP-A235-xxx motors.
Incorrect: The cable
lacks a drip loop.
Incorrect: The cable
lacks a drip loop.

4Rockwell Automation Publication TLP-IN001A-EN-P - October 2019
Kinetix TLP Servo Motors with 046…235 mm Frame Size
Prevent Electrical Noise
Electromagnetic interference (EMI), commonly called electrical noise, can affect motor performance. Follow these guidelines to reduce the effects
of EMI:
• Isolate the power transformers or install line filters on all AC input power lines.
• Use shielded cables.
• Shield signal cables from power wiring.
• Do not route motor cables over the vent openings on servo drives.
• Ground all equipment by using a single-point parallel ground system that employs ground bus-bars or large straps.
• If necessary, use additional electrical-noise reduction techniques to reduce EMI in noisy environments.
See System Design for Control of Electrical Noise Reference Manual, publication GMC-RM001, for additional information on reducing EMI.
Install Cables
Correct cable routing and careful cable construction improve system electromagnetic compatibility (EMC).
Follow these guidelines to build and install the cables:
• Keep the wire lengths as short as possible.
• Route noise sensitive wiring (encoder, serial, and I/O) away from input power and motor power wiring.
• Separate cables by 0.3 m (1 ft) minimum for every 9 m (30 ft) of parallel run.
• Ground both ends of the encoder cable shield and twist the signal wire pairs to help prevent EMI from other equipment.
Motor Installation
Motor installation must comply with all local regulations and use of equipment and installation practices that promote safety and electromagnetic
compatibility:
• All motors include a mounting pilot for aligning the motor on a machine.
• Preferred fasteners are stainless steel.
ATTENTION: Damage can occur to the motor bearings and the feedback device if sharp impact is applied tothe shaft during installation of couplings and pulleys.
Damage to the feedback device can result from applying leverage to the motor mounting face when removing devices mounted on the motor shaft.
Do not strike the shaft, couplings, or pulleys with tools during installation or removal. Use a wheel puller, to apply pressure from the user end of the shaft, when
attempting to remove any device from the motor shaft.
ATTENTION: High voltage can be present on the shield of a power cable, if the shield is not grounded.Verify that there is a connection to ground for any power
cable shield.
ATTENTION: Unmounted motors, disconnected mechanical couplings, loose shaft keys, and disconnected cables are dangerous if power is applied. Identify
(tag-out) disassembled equipment and restrict access to (lock-out) the electrical power.
Before applying power to the motor, remove the shaft key and other mechanical couplings that could be thrown from the shaft.
ATTENTION: Verify that cables are installed and restrained to prevent uneven tension or flexing at the connector. Provide support at 3 m (10ft)intervals
throughout the cable run.
Excessive and uneven lateral force at the cable connector can result in the connector’s environmental seal opening and closing as the cable flexes.

Rockwell Automation Publication TLP-IN001A-EN-P - October 2019 5
Kinetix TLP Servo Motors with 046…235 mm Frame Size
Install the Motor
Perform these steps to install the motor.
1. Leave enough space around the motor so it can dissipate heat and stay within its specified operating temperature range.
See Environmental Specifications on page 15 for the operating temperature range. Do not enclose the motor unless forced air is blown
across the motor for cooling. A fan that blows air across the motor improves its performance. Keep other heat-producing devices away from
the motor.
2. See Load Force Ratings on page 10 to determine the radial and axial shaft load limitations of your motor.
3. Install the motor with the connector positioned beneath the motor housing.
This position can provide better environmental protection for the connector.
4. Mount and align the motor.
5. Attach the motor cables that transmit power, feedback, and brake signals as described below.
a. Carefully align the cable connector with the motor connector.
b. Hand-tighten military style connectors on TLP-A115…TLP-A235 motors and press rectangular connectors together on
TLP-A046…TLP-A100 motors until the contacts are inserted and a click is heard.
ATTENTION: Damage can occur to the motor bearings and the feedback device if sharp impact is applied tothe shaft during installation of couplings and pulleys.
Damage to the feedback device can result from applying leverage to the motor mounting face when removing devices mounted on the motor shaft.
Do not strike the shaft, couplings, or pulleys with tools during installation or removal. Use a wheel puller, to apply pressure from the user end of the shaft, when
attempting to remove any device from the motor shaft.
BURN HAZARD: Outer surfaces of the motor can reach a high temperature, 125 °C (257 °F), during motor operation.
Take precautions to prevent accidental contact with hot surfaces. Consider motor surface temperature when selecting motor mating connections and
cables.
ATTENTION: Keyed connectors must be properly aligned and hand-tightened.
Do not use tools, or apply excessive force, when mating the cable to the motor connector. If the connectors do not go together with light hand force,
realign and try again.
ATTENTION: The overall shield on the motor cable must be grounded to obtain an effective encoder signal.
The encoder data signal is transmitted through an impedance-matched twisted-wire pair that requires effective shielding for optimum performance.
Make sure there is an effective connection between the motor cable shield and the drive system ground.

6Rockwell Automation Publication TLP-IN001A-EN-P - October 2019
Kinetix TLP Servo Motors with 046…235 mm Frame Size
Motor Dimensions (046…100 mm frame sizes)
Motor Dimensions (046…100 mm frame sizes)
Motors are designed to metric dimensions. Inch dimensions are approximate conversions from millimeters. Dimensions without tolerances are for
reference.
Motor
Cat. No.
HD
mm (in.)
LA
mm (in.)
LB (1)
mm (in.)
(1) ForTLP-A046-005 motors with brake, add 34.2 mm (1.35 in.). For TLP-A046-010 motors with brake, add 34.8 mm (1.37 in.).
ForTLP-A070-020 motors with brake, add 33.6 mm (1.32 in.). For TLP-A070-040 motors with brake, add 33.7 mm (1.33 in.).
For TLP-A090-075 motors with brake, add 37.4 mm (1.47 in.).
For TLP-A100-100 motors with brake, add 31.1 mm (1.22 in.).
L-LB (2)
mm (in.)
(2) Tolerance for this dimension is ±0.50 mm (±0.020 in.).
LW
mm (in.)
D
mm (in.)
M
mm (in.)
S
mm (in.)
N (5)
mm (in.)
(5) See dimensions diagram for tolerances.
P
mm (in.)
G
mm (in.)
GD
mm (in.)
W
mm (in.)
WK
mm (in.)
TLP-A046-005
53.8
(2.12)
5.0
(0.20)
71.9
(2.83) 25.0
(0.98)
16.0
(0.630)
8.0
(0.3149)
46.0
(1.811)
4.50 (3)
(0.177)
(3) Tolerance for this dimension is ±0.10 mm (±0.0039 in.).
30.0
(1.181)
40.0
(1.57)
6.20
(0.244)
3.0
(0.118)
3.0 (6)
(0.118)
(6) Tolerance for this dimension is -0.004, -0.029 mm (0.000157, -0.001141 in.).
3.0 (8)
(0.118)
(8) Tolerance for this dimension is +0, -0.025 mm (+0, -0.000984 in.).
TLP-A046-010 86.0
(3.39)
TLP-A070-020
74.1
(2.92)
7.5
(0.30)
84.7
(3.33) 30.0
(1.18)
20.0
(0.787)
14.0
(0.5512)
70.0
(2.756)
5.50 (4)
(0.216)
(4) Tolerance for this dimension is ±0.20 mm (±0.0079 in.).
50.0
(1.968)
60.0
(2.36)
11.0
(0.433)
5.0
(0.197)
5.0 (7)
(0.197)
(7) Tolerance for this dimension is +0, -0.030 mm (+0, -0.001181 in.).
5.0 (7)
(0.197)
TLP-A070-040 106.7
(4.20)
TLP-A090-075 94.1
(3.70) 8.0
(0.31)
116.5
(4.59)
40.0
(1.57)
25.0
(0.984)
19.0
(0.7480)
90.0
(3.543)
6.60 (4)
(0.260)
70.0
(2.755)
80.0
(3.15)
15.5
(0.610)
6.0
(0.236)
6.0 (7)
(0.236)
6.0 (7)
(0.236)
TLP-A100-100 98.8
(3.89)
153.9
(6.06)
35.0
(1.38)
20.0
(0.787)
16.0
(0.6299)
100
(3.937)
6.60 (3)
(0.260)
80.0
(3.149)
86.0
(3.38)
13.0
(0.630)
5.0
(0.197)
5.0 (7)
(0.197)
5.0 (7)
(0.197)
LB
LE ±50
(2.0 in.)
LP ±50
(2.0 in.) L-LB
LA
T
DNP
HD
TP
WK
GD
W
G
LW
Shaft End Details
Shaft
Diameter
S Diameter Holes on
M Diameter Bolt Circle
Dimensions are in mm (in.)
Power Connector
Feedback Connector Pilot Diameter Tolerances
TLP-A046xx Motors:
Ø 29.979…30.000 (1.180…1.181)
TLP-A070xx Motors:
Ø 49.975…50.000 (1.967…1.968)
TLP-A090xx Motors:
Ø 69.970…70.000 (2.754…2.755)
TLP-A100xx Motors:
Ø 79.970…80.000 (3.148…3.149)
Key Details
Shaft Diameter Tolerances
TLP-A046xx Motors:
Ø 7.991…8.000 (0.3146…0.3149)
TLP-A070xx Motors:
Ø 13.989…14.000 (0.5507…0.5512)
TLP-A090xx Motors:
Ø 18.987…19.000 (0.7475…0.7480)
TLP-A100xx Motors:
Ø 15.989…16.000 (0.6295…0.6299)
Optional Shaft Seal
Refer to page 15
for motor shaft seal
kit information.
Shaft and Pilot Tolerances TLP-A046xx TLP-A070xx TLP-A090xx TLP-A100xx
Shaft Runout (T.I.R.) 0.02 (0.0008) 0.02 (0.0008) 0.02 (0.0008) 0.02 (0.0008)
Pilot Eccentricity (T.I.R.) 0.04 (0.0016) 0.30 (0.0118) 0.04 (0.0016) 0.04 (0.0016)
Max Face Runout (T.I.R.) 0.04 (0.0016) 0.04 (0.0016) 0.04 (0.0016) 0.04 (0.0016)
Shaft-end Threaded Hole (TP) M3x0.5-6H, 6 M4x0.7-6H, 8 M6x1.0-6H, 10 M5x0.8-6H, 15
On-motor Cable Length (LE/LP) A1 Connector = 1.0 m (39.4 in.), A3 Connector = 300 mm (11.8 in.)

Rockwell Automation Publication TLP-IN001A-EN-P - October 2019 7
Kinetix TLP Servo Motors with 046…235 mm Frame Size
Motor Dimensions (115 and 145 mm frame sizes)
Motor Dimensions (115 and 145 mm frame sizes)
Motors are designed to metric dimensions. Inch dimensions are approximate conversions from millimeters. Dimensions without tolerances are for
reference.
Motor
Cat. No.
HD
mm (in.)
HD1
mm (in.)
LA
mm (in.)
LB (1)
mm (in.)
(1) For TLP-A115-100 motors with brake, add 39.3 mm (1.55 in.).
For TLP-A115-200 motors with brake, add 27.0 mm (1.06 in.).
ForTLP-A145-050 and TLP-A145-100 motors with brake, add 36.0 mm (1.42 in.).
ForTLP-A145-090 and TLP-A145-150 motors with brake, add 34.5 mm (1.36 in.).
L-LB
mm (in.)
LW
mm (in.)
D (3)
mm (in.)
(3) See dimensions diagram for tolerances.
M
mm (in.)
S (4)
mm (in.)
(4) ForTLP-A115 motors, the tolerance is ±0.10 mm (±0.0039 in.).
ForTLP-A145 motors, the tolerance is ±0.30 mm (±0.0118 in.).
N (3)
mm (in.)
P
mm (in.)
G
mm (in.)
GD
mm (in.)
W (5)
mm (in.)
(5) Tolerance for this dimension is +0, -0.036 mm (+0, -0.01417 in.).
WK (5)
mm (in.)
TLP-A115-100
122.9
(4.84)
148.1
(5.83)
12.0
(0.47)
154.0
(6.06) 45.0 (2)
(1.77)
(2) Tolerance for this dimension is +0.38, -0.50 mm (+0.015, -0.020 in.).
36.0
(1.42)
22.0
(0.87)
115
(4.53)
9.0
(0.354)
95.0
(3.74)
100
(3.94)
18.0
(0.71) 7.0
(0.28)
8.0
(0.315)
8.0
(0.315)
TLP-A115-200 199.7
(7.86)
TLP-A145-050
138.6
(5.46)
176.4
(6.94)
11.5
(0.45)
148.2
(5.83)
55.0
(2.17)
145
(5.71)
110
(4.33)
130
(5.12)
TLP-A145-090 164.2
(6.46)
TLP-A145-100 148.2
(5.83)
TLP-A145-150 168.2
(6.62)
LA
DNP
TP
WK
GD
W
G
HD
HD1
LB
L-LB
T
LW
LW
Shaft End Details
Shaft
Diameter
Optional Shaft Seal
Refer to page 15
for motor shaft seal
kit information.
S Diameter Holes on
M Diameter Bolt Circle
Dimensions are in mm (in.)
Shaft and Pilot Tolerances TLP-A115xx TLP-A145xx
Shaft Runout (T.I.R.) 0.02 (0.0008) 0.02 (0.0008)
Pilot Eccentricity (T.I.R.) 0.04 (0.0016) 0.04 (0.0016)
Max Face Runout (T.I.R.) 0.02 (0.0008) 0.04 (0.0016)
Shaft-end Threaded Hole (TP) M6x1.0-6H, 20 M6x1.0-6H, 20
Power Connector
Feedback Connector
Pilot Diameter Tolerances
TLP-A115xx Motors:
Ø 94.965…95.000 (3.739…3.740)
TLP-A145xx Motors:
Ø 109.965…110.000 (4.329…4.330)
Key Details
Shaft Diameter Tolerances
TLP-A115xx Motors:
Ø 21.987…22.000 (0.9656…0.8661)
TLP-A145-050… TLP-A145-150 Motors:
Ø 21.987…22.000 (0.9656…0.8661)
Alternative Shaft
Keyway Type

8Rockwell Automation Publication TLP-IN001A-EN-P - October 2019
Kinetix TLP Servo Motors with 046…235 mm Frame Size
Motor Dimensions (200 and 235 mm frame sizes)
Motor Dimensions (200 and 235 mm frame sizes)
Motors are designed to metric dimensions. Inch dimensions are approximate conversions from millimeters. Dimensions without tolerances are for
reference.
Motor
Cat. No.
HD
mm (in.)
HD1
mm (in.)
LA
mm (in.)
LB (1)
mm (in.)
(1) ForTLP-A200-200 and TLP-A200-750 motors with brake, add 34.1 mm (1.34 in.).
ForTLP-A200-300 and TLP-A200-350 motors with brake, add 33.2 mm (1.31 in.).
For TLP-A200-450 motors with brake, add 44.0 mm (1.73 in.).
For TLP-A200-550 motors with brake, add 32.0 mm (1.26 in.).
ForTLP-A235-11K and TLP-A235-15K motors with brake, add 63.0 mm (2.48 in.).
L-LB (2)
mm (in.)
(2) Tolerance for this dimension is +0.38, -0.50 mm (+0.015, -0.020 in.).
LW
mm (in.)
D
mm (in.)
M
mm (in.)
S
mm (in.)
N (5)
mm (in.)
(5) See dimensions diagram for tolerances.
P
mm (in.)
G
mm (in.)
GD
mm (in.)
W
mm (in.)
WK (5)
mm (in.)
TLP-A200-200
174.9
(6.89)
231.0
(9.09)
20.0
(0.79)
169.7
(6.68)
79.0
(3.11)
63.0
(2.48)
35.0
(1.38)
200.0
(7.87)
13.5 (3)
(0.53)
(3) Tolerance for this dimension is ±0.10 mm (±0.0039 in.).
114.3
(4.50)
180.0
(7.09)
30.0
(1.18)
8.0
(0.31)
10.0 (6)
(0.394)
(6) Tolerance for this dimension is +0, -0.036 mm (+0, -0.01417 in.).
10.0 (6)
(0.394)
TLP-A200-300 202.8
(7.98)
TLP-A200-350
TLP-A200-450 254.0
(10.0)
TLP-A200-550
240.0
(9.45)
280.4
(11.04) 113.0
(4.45)
90.0
(3.54)
42.0
(1.65) 13.5 (4)
(0.53)
(4) Tolerance for this dimension is ±0.20 mm (±0.0079 in.).
37.0
(1.46)
12.0 (7)
(0.47)
(7) Tolerance for this dimension is +0, -0.043 mm (+0, -0.00169 in.).
12.0 (7)
(0.47)
TLP-A200-750 342.7
(13.49)
TLP-A235-11K
194.6
(7.66)
279.1
(10.99)
372.1
(14.65) 116.0
(4.57)
235.0
(9.25)
200.0
(7.87)
220.0
(8.66)
TLP-A235-15K 451.1
(17.76)
55.0
(2.17)
49.0
(1.93)
10.0
(0.39)
16.0 (7)
(0.63)
16.0 (7)
(0.63)
LA
TP
WK
GD
W
L-LB
T
HD
HD1
LW
DN
LB
P
LW
G
Shaft End Details
Shaft Diameter
Optional Shaft Seal
Refer to page 15 for motor
shaft seal kit information.
S Diameter Holes on
M Diameter Bolt Circle
Dimensions are in mm (in.)
Shaft and Pilot Tolerances TLP-A200-xxx TLP-A235-11K TLP-A235-15K
Shaft Runout (T.I.R.) 0.02 (0.0008) 0.04 (0.0016) 0.04 (0.0016)
Pilot Eccentricity (T.I.R.) 0.04 (0.0016) 0.04 (0.0016) 0.04 (0.0016)
Max Face Runout (T.I.R.) 0.04 (0.0016) 0.06 (0.0024) 0.06 (0.0024)
Shaft-endThreaded Hole (TP) M12x1.75-6H, 25 M16x2.0-6H, 32 M20x2.5-6H, 40
Power Connector
Feedback
Connector
Pilot Diameter Tolerances
TLP-A200-200…TLP-A200-750 Motors:
Ø 114.265…114.300 (4.4986…4.500)
TLP-A235-11K…TLP-A235-15K Motors:
Ø 199.954…200.00 (7.8722…7.8740)
Key Details
Shaft Diameter Tolerances
TLP-A200-200…TLP-A200-450 Motors:
Ø 34.984…35.000 (1.3773…1.3779)
TLP-A200-550…TLP-A200-750 Motors:
Ø 41.984…42.000 (1.6529…1.6535)
TLP-A235-11K Motors:
Ø 41.984…42.000 (1.6529…1.6535)
TLP-A235-15K Motors:
Ø 54.989…55.030 (2.1649…2.1665)
Alternative Shaft
Keyway Type
Lifting points apply toTLP-A200-550,
TLP-A200-750, and TLP-A235-xxx
servo motors only.
Brake connectors apply to TLP-A200-550,
TLP-A200-750, and TLP-A235-xxx
servo motors only.
Power Connector
Feedback
Connector
Brake
Connector

Rockwell Automation Publication TLP-IN001A-EN-P - October 2019 9
Kinetix TLP Servo Motors with 046…235 mm Frame Size
Connector Data
This section identifies the power, feedback, and brake pins on the motor connectors.
The motor power connector pinouts apply to the motor catalog numbers listed.
Motor Power Connector Pinouts
Motor Brake Connector Pinout
Motor Feedback Connector Pinouts
Pin Signal Motor Cat. No.
1U
TLP-A046
TLP-A070
TLP-A090
TLP-A100
2V
3BR+
4W
5
6BR–
12
6
5
4
3
Pin Signal Motor Cat. No.
A–
TLP-A115
TLP-A145
BW
C–
D–
E
FU
GBR+
HBR–
IV
A
B
C
D
E
F
G
H
I
Pin Signal Motor Cat. No.
ABR+
TLP-A200-200
TLP-A200-300
TLP-A200-350
TLP-A200-450
BBR–
C–
DU
EV
FW
G
H–
J–
A
B
C
D
E
F
G
H
I
Pin Signal Motor Cat. No.
AU
TLP-A200-550
TLP-A200-750
TLP-A235-11K
TLP-A235-15K
BV
CW
D
A
B
CD
Pin Signal Motor Cat. No.
A BR+ TLP-A200-550
TLP-A200-750
TLP-A235-11K
TLP-A235-15K
BBR–
A
B
Pin Signal Motor Cat. No.
1T+
TLP-A046
TLP-A070
TLP-A090
TLP-A100
2BAT+
3–
4T–
5BAT–
6–
7DC+5V
8
9SHIELD
12
6
5
4
3
9
8
7
Pin Signal Motor Cat. No.
AT+
TLP-A115
TLP-A145
TLP-A200
TLP-A235
BT–
CBAT+
DBAT–
E…K –
LSHIELD
M…P –
R
SDC+5V
T–
A
B
C
D
E
F
G
H
JKL
M
N
P
R
ST

10 Rockwell Automation Publication TLP-IN001A-EN-P - October 2019
Kinetix TLP Servo Motors with 046…235 mm Frame Size
Load Force Ratings
Motors are capable of operating with a sustained shaft load. The location and direction of radial and axial load forces are shown in the figure, and
maximum load rating values are in the tables.
Load Forces on Shaft
The following tables represent 40,000-hour L10 bearing fatigue life at various loads and speeds. This 40,000-hour bearing life does not account for
possible application-specific life reduction, such as bearing grease contamination from external sources.
Radial Load Force Ratings (maximum) for Non-brake Motors
Motor
Cat. No. (1)
(1) 1.0 kgf = 2.2 lbf or 9.8 N.
Speed, max
rpm
RPM
500
kgf
750
kgf
1000
kgf
1125
kgf
1250
kgf
1500
kgf
2000
kgf
2250
kgf
2500
kgf
3000
kgf
3375
kgf
3750
kgf
4500
kgf
5000
kgf
6000
kgf
TLP-A046-005-Dxxx2x6000 –––––8.8–––7.0––6.1–5.6
TLP-A046-010-Dxxx2x6000 –––––9.7–––7.7––6.8–6.1
TLP-A070-020-Dxxx2x6000 –––––22.4–––17.8––15.5–14.1
TLP-A070-040-Dxxx2x6000 –––––25–––19.9––17.4–15.8
TLP-A090-075-Dxxx2x6000 –––––35.6–––28.2––24.7–22.4
TLP-A100-100-Dxxx2x3000 –61.8–––49.0–42.8–38.9–––––
TLP-A115-100-Dxxx2x5000 – – – – 52.9 – – – 42 – – 36.7 – 33.3 –
TLP-A115-200-Dxxx2x5000 – – – – 58.1 – – – 46.1 – – 10.3 – 36.6 –
TLP-A145-050-Dxxx2x3000 –106.8–––84.7–74–67.3–––––
TLP-A145-090-Dxxx2x2000 130.1–103.3––90.282––––––––
TLP-A145-100-Dxxx2x3000 –106.8–––84.7–74–67.3–––––
TLP-A145-150-Dxxx2x3000 –113.6–––90.2–78.8–71.6–––––
TLP-A200-200-Dxxx2x3000 –125.9–––99.9–87.3–79.3–––––
TLP-A200-300-Dxxx2x2500 –140–––111.1–97.1–88.2–––––
TLP-A200-350-Dxxx2x3000 –140–––111.1–97.1–88.2–––––
TLP-A200-450-Dxxx2x3000 –149.7–––118.8–103.8–94.3–––––
TLP-A200-550-Dxxx2x3000 –149.2–––118.4–103.4–94–––––
TLP-A200-750-Dxxx2x2500 –159.3–––126.4–110.4–100.3–––––
TLP-A235-11K-Dxxx2x2000 435–345.3––301.6274––––––––
TLP-A235-15K-Dxxx2x2000 463.1–367.6––321.1291.7––––––––
Axial load force applied to the center of the shaft.
Radial load force applied at the midpoint of the shaft extension.

Rockwell Automation Publication TLP-IN001A-EN-P - October 2019 11
Kinetix TLP Servo Motors with 046…235 mm Frame Size
Axial Load Force Ratings (maximum radial load) for Non-brake Motors
Motor
Cat. No. (1)
(1) 1.0 kgf = 2.2 lbf or 9.8 N.
Speed, max
rpm
RPM
500
kgf
750
kgf
1000
kgf
1125
kgf
1250
kgf
1500
kgf
2000
kgf
2250
kgf
2500
kgf
3000
kgf
3375
kgf
3750
kgf
4500
kgf
5000
kgf
6000
kgf
TLP-A046-005-Dxxx2x6000 –––––5.6–––4.1––3.4–3.0
TLP-A046-010-Dxxx2x6000 –––––6 –––4.4––3.7–3.3
TLP-A070-020-Dxxx2x6000 –––––10.1–––7.4––6.2–5.5
TLP-A070-040-Dxxx2x6000 –––––11.3–––8.3––7.0–6.2
TLP-A090-075-Dxxx2x6000 –––––13.6–––10.1––8.5–7.5
TLP-A100-100-Dxxx2x3000 –18.4–––13.6–11.4–10.1–––––
TLP-A115-100-Dxxx2x5000 – – – – 18.1 – – – 13.4 – – 11.2 – 9.9 –
TLP-A115-200-Dxxx2x5000 – – – – 20.5 – – – 15.1 – – 12.7 – 11.2 –
TLP-A145-050-Dxxx2x3000 –28.1–––20.8–17.5–15.4–––––
TLP-A145-090-Dxxx2x2000 37.2–27.5––23.120.4––––––––
TLP-A145-100-Dxxx2x3000 –28.1–––20.8–17.5–15.4–––––
TLP-A145-150-Dxxx2x3000 –31.2–––23.1–19.4–17.1–––––
TLP-A200-200-Dxxx2x3000 –54.3–––40.2–33.7–29.7–––––
TLP-A200-300-Dxxx2x2500 –60.8–––45.0–37.7–33.3–––––
TLP-A200-350-Dxxx2x3000 –60.8–––45.0–37.7–33.3–––––
TLP-A200-450-Dxxx2x3000 –65.3–––48.3–40.5–35.8–––––
TLP-A200-550-Dxxx2x3000 –65.0–––48.1–40.3–35.6–––––
TLP-A200-750-Dxxx2x2500 –69.8–––51.7–43.3–38.2–––––
TLP-A235-11K-Dxxx2x2000 65.0–48.1––40.335.6––––––––
TLP-A235-15K-Dxxx2x2000 77.7–57.5––48.242.6––––––––
Axial Load Force Ratings (zero radial load) for Non-brake Motors
Motor
Cat. No. (1) Speed, max
rpm
RPM
500
kgf
750
kgf
1000
kgf
1125
kgf
1250
kgf
1500
kgf
2000
kgf
2250
kgf
2500
kgf
3000
kgf
3375
kgf
3750
kgf
4500
kgf
5000
kgf
6000
kgf
TLP-A046-005-Dxxx2x6000 –––––7.8–––5.7––4.8–4.2
TLP-A046-010-Dxxx2x6000 –––––7.8–––5.7––4.8–4.2
TLP-A070-020-Dxxx2x6000 –––––15.4–––11.4––9.5–8.4
TLP-A070-040-Dxxx2x6000 –––––15.4–––11.4––9.5–8.4
TLP-A090-075-Dxxx2x6000 –––––20.4–––15.1––12.6–11.1
TLP-A100-100-Dxxx2x3000 –27.5–––20.4–17.1–15.1–––––
TLP-A115-100-Dxxx2x5000 – – – – 27.9 – – – 20.6 – – 17.3 – 15.3 –
TLP-A115-200-Dxxx2x5000 – – – – 27.9 – – – 20.6 – – 17.3 – 15.3 –
TLP-A145-050-Dxxx2x3000 –56.4–––41.7–35.0–30.9–––––
TLP-A145-090-Dxxx2x2000 67.2–49.7––41.736.8––––––––
TLP-A145-100-Dxxx2x3000 –56.4–––41.7–35.0–30.9–––––
TLP-A145-150-Dxxx2x3000 –56.4–––41.7–35.0–30.9–––––
TLP-A200-200-Dxxx2x3000 –91.9–––68.0–57.0–50.3–––––
TLP-A200-300-Dxxx2x2500 –91.9–––68.0–57.0–50.3–––––

12 Rockwell Automation Publication TLP-IN001A-EN-P - October 2019
Kinetix TLP Servo Motors with 046…235 mm Frame Size
Radial Load Force Ratings (maximum) for Brake Motors
TLP-A200-350-Dxxx2x3000 –91.9–––68.0–57.0–50.3–––––
TLP-A200-450-Dxxx2x3000 –91.9–––68.0–57.0–50.3–––––
TLP-A200-550-Dxxx2x3000 –91.9–––68.0–57.0–50.3–––––
TLP-A200-750-Dxxx2x2500 –91.9–––68.0–57.0–50.3–––––
TLP-A235-11K-Dxxx2x2000 136.5–101.0––84.774.8––––––––
TLP-A235-15K-Dxxx2x2000 136.5–101.0––84.774.8––––––––
(1) 1.0 kgf = 2.2 lbf or 9.8 N.
Motor
Cat. No. (1)
(1) 1.0 kgf = 2.2 lbf or 9.8 N.
Speed, max
rpm
RPM
500
kgf
750
kgf
1000
kgf
1125
kgf
1250
kgf
1500
kgf
2000
kgf
2250
kgf
2500
kgf
3000
kgf
3375
kgf
3750
kgf
4500
kgf
5000
kgf
6000
kgf
TLP-A046-005-Dxxx4x6000 –––––10.5–––8.4––7.3–6.6
TLP-A046-010-Dxxx4x6000 –––––10.9–––8.7––7.6–6.9
TLP-A070-020-Dxxx4x6000 –––––26–––20.6––18–16.4
TLP-A070-040-Dxxx4x6000 –––––27.3–––21.7––18.9–17.2
TLP-A090-075-Dxxx4x6000 –––––39.3–––31.2––27.2–24.7
TLP-A100-100-Dxxx4x3000 –65.3–––51.8–45.3–41.1–––––
TLP-A115-100-Dxxx4x5000 ––––57.9–––45.9––40.1–36.4–
TLP-A115-200-Dxxx4x5000 ––––60.3–––47.8––41.8–38–
TLP-A145-050-Dxxx4x3000 –120.3–––95.5–83.4–75.8–––––
TLP-A145-090-Dxxx4x2000 142.1–112.8––98.589.5––––––––
TLP-A145-100-Dxxx4x3000 –120.3–––95.5–83.4–75.8–––––
TLP-A145-150-Dxxx4x3000 –124.1–––98.5–86–78.2–––––
TLP-A200-200-Dxxx4x3000 – 140.4 – – – 111.4 – 97.3 – 88.4 –––––
TLP-A200-300-Dxxx4x2500 – 149.7 – – – 118.8 – 103.8 – 94.3 –––––
TLP-A200-350-Dxxx4x3000 – 149.7 – – – 118.8 – 103.8 – 94.3 –––––
TLP-A200-450-Dxxx4x3000 – 158.8 – – – 126.1 – 110.1 – 100.1 –––––
TLP-A200-550-Dxxx4x3000 – 154.8 – – – 122.9 – 107.3 – 97.5 –––––
TLP-A200-750-Dxxx4x2500 – 163.3 – – – 129.6 – 113.2 – 102.9 –––––
TLP-A235-11K-Dxxx4x2000 458.3 – 363.8 – – 317.8 288.7 – – – –––––
TLP-A235-15K-Dxxx4x2000 478.8–380––332301.6––––––––
Axial Load Force Ratings (zero radial load) for Non-brake Motors (continued)
Motor
Cat. No. (1) Speed, max
rpm
RPM
500
kgf
750
kgf
1000
kgf
1125
kgf
1250
kgf
1500
kgf
2000
kgf
2250
kgf
2500
kgf
3000
kgf
3375
kgf
3750
kgf
4500
kgf
5000
kgf
6000
kgf

Rockwell Automation Publication TLP-IN001A-EN-P - October 2019 13
Kinetix TLP Servo Motors with 046…235 mm Frame Size
Axial Load Force Ratings (maximum radial load) for Brake Motors
Motor Cat. No. (1)
(1) 1.0 kgf = 2.2 lbf or 9.8 N.
Speed, max
rpm
RPM
500
kgf
750
kgf
1000
kgf
1125
kgf
1250
kgf
1500
kgf
2000
kgf
2250
kgf
2500
kgf
3000
kgf
3375
kgf
3750
kgf
4500
kgf
5000
kgf
6000
kgf
TLP-A046-005-Dxxx4x6000 –––––6.7–––5 ––4.2–3.7
TLP-A046-010-Dxxx4x6000 –––––6.9–––5.1––4.3–3.8
TLP-A070-020-Dxxx4x6000 –––––11.7–––8.7––7.3–6.4
TLP-A070-040-Dxxx4x6000 –––––12.3–––9.1––7.6–6.7
TLP-A090-075-Dxxx4x6000 –––––15.3–––11.3––9.5–8.4
TLP-A100-100-Dxxx4x3000 –20.1–––14.9–12.5–11–––––
TLP-A115-100-Dxxx4x5000 – – – – 20.3 – – – 15 – – 12.6 – 11.1 –
TLP-A115-200-Dxxx4x5000 – – – – 21.5 – – – 15.9 – – 13.3 – 11.8 –
TLP-A145-050-Dxxx4x3000 –34.2–––25.3–21.2–18.7–––––
TLP-A145-090-Dxxx4x2000 42.9–31.8––26.623.5––––––––
TLP-A145-100-Dxxx4x3000 –34.2–––25.3–21.2–18.7–––––
TLP-A145-150-Dxxx4x3000 –36–––26.6–22.3–19.7–––––
TLP-A200-200-Dxxx4x3000 –60.9–––45.1–37.8–33.4–––––
TLP-A200-300-Dxxx4x2500 –65.3–––48.3–40.5–35.8–––––
TLP-A200-350-Dxxx4x3000 –65.3–––48.3–40.5–35.8–––––
TLP-A200-450-Dxxx4x3000 –69.6–––51.5–43.2–38.1–––––
TLP-A200-550-Dxxx4x3000 –67.7–––50.1–42–37.1–––––
TLP-A200-750-Dxxx4x2500 –71.7–––53.1–44.5–39.3–––––
TLP-A235-11K-Dxxx4x2000 75.5–55.9––46.841.3––––––––
TLP-A235-15K-Dxxx4x2000 85–62.9––52.846.6––––––––

14 Rockwell Automation Publication TLP-IN001A-EN-P - October 2019
Kinetix TLP Servo Motors with 046…235 mm Frame Size
Axial Load Force Ratings (zero radial load) for Brake Motors
Motor
Cat. No. (1)
(1) 1.0 kgf = 2.2 lbf or 9.8 N.
Speed, max
rpm
RPM
500
kgf
750
kgf
1000
kgf
1125
kgf
1250
kgf
1500
kgf
2000
kgf
2250
kgf
2500
kgf
3000
kgf
3375
kgf
3750
kgf
4500
kgf
5000
kgf
6000
kgf
TLP-A046-005-Dxxx4x6000 –––––8.1–––6 ––5.0–4.4
TLP-A046-010-Dxxx4x6000 –––––8.1–––6 ––5.0–4.4
TLP-A070-020-Dxxx4x6000 –––––15.4–––11.4––9.5–8.4
TLP-A070-040-Dxxx4x6000 –––––15.4–––11.4––9.5–8.4
TLP-A090-075-Dxxx4x6000 –––––20.4–––15.1––12.6–11.1
TLP-A100-100-Dxxx4x3000 –27.5–––20.4–17.1–15.1–––––
TLP-A115-100-Dxxx4x5000 – – – – 27.9 – – – 20.6 – – 17.3 – 15.3 –
TLP-A115-200-Dxxx4x5000 – – – – 27.9 – – – 20.6 – – 17.3 – 15.3 –
TLP-A145-050-Dxxx4x3000 –56.4–––41.7–35.0–30.9–––––
TLP-A145-090-Dxxx4x2000 67.2–49.7––41.736.8––––––––
TLP-A145-100-Dxxx4x3000 –56.4–––41.7–35.0–30.9–––––
TLP-A145-150-Dxxx4x3000 –56.4–––41.7–35.0–30.9–––––
TLP-A200-200-Dxxx4x3000 –91.9–––68.0–57.0–50.3–––––
TLP-A200-300-Dxxx4x2500 –91.9–––68.0–57.0–50.3–––––
TLP-A200-350-Dxxx4x3000 –91.9–––68.0–57.0–50.3–––––
TLP-A200-450-Dxxx4x3000 –91.9–––68.0–57.0–50.3–––––
TLP-A200-550-Dxxx4x3000 –91.9–––68.0–57.0–50.3–––––
TLP-A200-750-Dxxx4x2500 –91.9–––68.0–57.0–50.3–––––
TLP-A235-11K-Dxxx4x2000 136.5–101.0––84.774.8––––––––
TLP-A235-15K-Dxxx4x2000 136.5–101.0––84.774.8––––––––

Rockwell Automation Publication TLP-IN001A-EN-P - October 2019 15
Kinetix TLP Servo Motors with 046…235 mm Frame Size
Environmental Specifications
Always store motors in a clean and dry location within the environmental conditions.
Environmental Ratings
Motor Accessories
The following accessories are available for Kinetix TLP servo motors.
2090-Series Motor Cables
Factory manufactured feedback, power, and brake cables are available in standard cable lengths. They provide the sealing that is needed to achieve
environmental ratings and shield termination. If you choose to build your own cables, connector kits available for Kinetix TLP motors are described
in the Kinetix Motion Accessories Specifications Technical Data, publication KNX-TD004.
Contact your nearest Rockwell Automation sales office or refer to the Kinetix Motion Accessories Technical Data, publication KNX-TD004, for
information about available 2090-Series cables for Kinetix TLP motors.
Shaft Seal Kits
Shaft seal kits are available, as are replacement kits for field installation. A shaft seal provides a barrier that prevents moisture and particles from
entering the motor bearings. Shaft seals are made of nitrile and kits and require lubrication to reduce wear.
Shaft Seal Kit Selection
See Shaft Seal Kits for Kinetix TLP Installation Instructions, publication 2090-IN044, for instructions on how to install a shaft seal.
Environmental Specifications
Attribute Value
Temperature, operating 0…40 °C (32…104 °F)
Temperature, storage -10…+80 °C (-14 …+176 °F)
Relative humidity 20…95% noncondensing
Kinetix TLP Motors IP Rating (1)
(1) IP rating descriptions are for reference only. Refer to the international standards for more complete rating descriptions.
Dust Protection Liquid Protection
On-motor cable connectors. IP30
Protection from objects with a
diameter of 2.5 mm (0.098 in.)
or more.
No protection from liquids.
Motor with shaft seal and Bulletin 2090 environmentally sealed cable
connectors. IP65 (2)
(2) IP40 without shaft seal installed.
Total protection from dust. Protected against low-pressure jets of water from all directions.
IMPORTANT Shaft seals are subject to wear and require periodic inspection and replacement. Replacement is recommended every 3 months, not to exceed 12 months,
depending on use.
Motor Cat. No. Shaft Seal Kit Cat. No. Motor Cat. No. Shaft Seal Kit Cat. No.
TLP-A046 TLP-SSN-F046 TLP-A115 TLP-SSN-F115
TLP-A070 TLP-SSN-F070 TLP-A145 TLP-SSN-F145
TLP-A090 TLP-SSN-F090 TLP-A200 TLP-SSN-F200
TLP-A100 TLP-SSN-F100 TLP-A235 TLP-SSN-F235

Allen-Bradley, Kinetix, Rockwell Automation, and Rockwell Software are trademarks of Rockwell Automation, Inc.
Trademarks not belonging to Rockwell Automation are property of their respective companies.
Rockwell Otomasyon Ticaret A.Ş., Kar Plaza İş Merkezi E Blok Kat:6 34752 İçerenköy, İstanbul, Tel: [phone]
Rockwell Automation maintains current product environmental information on its website at http://www.rockwellautomation.com/rockwellautomation/about-us/sustainability-ethics/product-environmental-compliance.page.
At the end of its life, this equipment should be collected separately from any unsorted municipal waste.
Publication TLP-IN001A-EN-P - October 2019
Copyright © 2019 Rockwell Automation, Inc. All rights reserved. Printed in the U.S.A.
Additional Resources
These documents contain information concerning related products from Rockwell Automation.
You can view or download publications at http://www.rockwellautomation.com/global/literature-library/overview.page.
Rockwell Automation Support
For technical support, visit http://www.rockwellautomation.com/support/overview.page.
Resource Description
Kinetix Rotary Motion Specifications Technical Data, publication KNX-TD001 Product specifications for Allen-Bradley® rotary motors, with performance, environmental,
certifications, load force, and dimension drawings.
Kinetix Servo Drives Specifications, publication KNX-TD003 Provides product specifications for Kinetix Integrated Motion over EtherNet/IP™, Integrated Motion
over Sercos interface, EtherNet/IP networking, and component servo drive families.
Kinetix Motion Accessories Specifications, publication KNX-TD004 Product specifications and dimensions for Allen-Bradley servo drive accessories.
Kinetix 5100 Servo Drives User Manual, publication 2198-UM004 Information on installing, configuring, starting, and troubleshooting a servo drive system.
Kinetix 5100 Drive System Design Guide, publication KNX-RM011 Information on drive system components and accessory items you need for your Kinetix drive/motor
combination.
Shaft Seal Kits for Kinetix TLP Servo Motors Installation Instructions, publication 2090-IN044 Information on the installation of a shaft seal on KinetixTL Pro servo motors.
Product Certifications website, rok.auto/certifications Provides declarations of conformity, certificates, and other certification details.
Allen-Bradley Industrial Automation Glossary, publication AG-7.1 A glossary of industrial automation terms and abbreviations.
System Design for Control of Electrical Noise Reference Manual, publication GMC-RM001 Information, examples, and techniques that are designed to minimize system failures that are caused
by electrical noise.