Rocky's EAZY ROLLERS 305/336 User manual

For use with 4" (outside diameter)
aluminum irrigation tubing.
(Not Supplied By Rocky's)
1
Insert one end of irrigation tubing into 4" hub
(item #65).
1
10529
55 10771 19 5
61
209
21
ROCKY'S EAZY ROLLERS INSTRUCTIONS - #3 PORTABLE
Bolt the castors (item #209) to the A-frames
(item #55), as shown in the diagram.
Assemble one end unit to the tube, using
the small handle (item #71), as shown in
the diagram.
Assemble the other end unit to the tube,
using the white knob (item #61).
For smoother operation, apply
petroleum based grease between the
hub (item #65) and the black bushing
(item #105). This should be done once a
year.
Position the assembled roller unit at the
widest end of the pool.
NOTE:
APPLY WATERPROOF
GREASE.
36
For regular shaped pools,
align the outside edge of the
tube parallel with the end of
the pool.
For irregular shaped pools,
the outside edge of the tube
should be 3'
inside
from the
end of
the pool.
5
1/16"
Insert the anchor bolt
(item #11) through
the spring (item
#25), through the
spring guard (item #109) and
through the hole of the A-frame.
Tools Required:
Reversible Electric Drill
1/2" Concrete (masonary) Drill Bit
Hammer & Center Punch or Nail.
5/16" Hex Head Socket Bit
1/2" Wrench
5/8" Wrench
SELF-DRILLING
NOTE:
Tube length should be about 1' wider than pool.
65
2
MARK
#1
4
15
65
Slug
MARK
#2
This box contains the following items:
1
5
11
15
19
21
25
29
55
61
65
71
101
103
105
107
109
201
209
Self-tapping Screw
5/16"x1" Bolt
3/8"x6" Anchor Bolt
Concrete Anchor
5/16" Washer
3/8" Washer
Spring
Acorn Nut
#3 A-Frame
White Knob
4" Regular Hub
Small Handle
Male Grommet
Female Grommet
Plastic Bushing
Plastic Washer
Spring Guard
22' Strapping
2" Plastic Wheels
12
2
2
2
2
8
2
4
2
1
2
1
10
10
2
2
2
1
4
501
505
511
515
505
21
517
523
55
533
539
545
549
549
555
555
109
587
583
ITEM
#
DESCRIPTIONQTY.
RE-
ORDER
#
11
25
109
Any questions,check out our Web Site:
www.rockysrollers.com
Go to FAQ (Frequently AskedQuestiona)
®
V E RY I M POR TA N T
PREVENT DROWNING
Attach Warning Label to one end of tube.
Hit center slug
with hammer &
center punch,or
large nail.
Drive the concrete anchor into
the hole with a hammer.
Leave the anchor raised 1/
16".
To set the concrete anchor,
then tap the slug into the hole with a
hammer, then using a center punch or
large nail drive the slug down into the
anchor forcing legs out into concrete.
Using one of the two holes in the A-frame as a guide,
make mark #1 on deck. With a 1/2" concrete drill
bit, drill a 1 1/2" deep hole at mark #1. Complete
steps 5 and 6 before continuing with step 4.
On the other side of the roller unit, make mark #2 by
using one of the two holes in the A-frame as of guide.
With a 1/2" concrete drill bit, drill a 1 1/2" deep hole
at mark #2.
NOTE:
Set one bolt at front of frame on one end and
one at the rear of the frame on the other end.
Repeat with other side.
With 2 self-drill/tapping screws
(item #1), attach hub to tube using
electric drill. Apply pressure to
ensure screw cuts into
aluminum tube then cuts
it's own thread.
(No predrilling required)

T9605074
7A
8A8B
7B
Open cover over the pool and set
into position. Ensure that the end
of the cover (where it attaches to
the roller) is square to the roller.
If the cover has seams, then the
seams should be parallel to the
roller. (This may not be possible
with some types of covers.)
When cutting the cover, al-
low a 1 1/2" wide border
around the pool edge to com-
pensate for shrinkage.
FOR IRREGULAR, KIDNEY, OR ROUND SHAPED INGROUND POOLS
Open cover over the pool and set
into position. Ensure that the
seams on the cover are parallel to
the roller. (This may not be possible
with some types of covers).
GROMMET DETAIL
Position the blue strap on the cover. With the
hole punch provided (item #207), punch a hole
through the strapping and the cover. Ensure that
the hole in strapping is at least 1 1/2" from the
end of the strap and that the hole in the cover is
at least 1 1/2" from the end of the cover. Use a
piece of wood to avoid damaging the hole punch.
COVER STRAP
WOOD
207
Insert female grommet (item #103) through hole
in strapping and cover. Ensure that material is
completely pushed down shaft. Insert male
grommet (item #101) into female grommet. Once
in place, hit gently with hammer until secure.
(Caution - excess force will break grommet).
COVER
101 STRAP
1
STRAP
Using self-
tapping/drill
screws (item #1),
secure strap to tube.
FOR REGULAR SHAPED INGROUND POOLS
ROLLER
SEAMS
1 1/2" BORDER
COVER
POOL
Attach the cut cover to
the roller with the blue
straps (See grommet
detail). Ensure length
of strap allows cover
to lay flat on pool, to
prevent wind from get-
ting under cover.
STRAPS EVERY 3'
COVER
POOL
SEAMS
ROLLER
A
When cutting the cover, allow a
1 1/2" wide border around the pool edge to com-
pensate for shrinkage.
For odd shaped pools, pinch the cover and attach the strap as shown. Attach the cut cover
to the roller with the blue straps (see grommet detail) by folding the cover in a straight line
as shown in the diagrams. Ensure that the fold in the cover is straight.
Cover
Strap
Grommets
STRAPS EVERY 3'
Roller
Fold in
cover
103
For odd shaped pools, pinch the cover and attach
the strap as shown.
ROCKY'S REEL SYSTEMS INC. Tel: [phone] Fax: [phone]
North America: Tel:[phone] Fax: [phone] Web Site: www.rockys.ca E-Mail: [email protected]a